Engineering Science and Materials Commons^™

Controlled Buckling Breakaway Cable Terminal, John D. Reid, John R. Rohde, Dean L. Sicking

Department of Mechanical and Materials Engineering: Faculty Publications

A crash attenuation apparatus for use with a guardrail system having rail posts and rail elements. An impact head has a buffer nose section and a rail post breaking beam system. The post breaking beam system has upper and lower breaking beams attached to the head. A guide tube is attached to the side of the head. A strut member extends from a first attachment point on the rail element to a second point downstream. Upon impact by a vehicle, the head breaks the first rail post, before impacting the strut and buckling the rail element downstream.

Performance Of Proton Exchange Membranefuel Cell With Co/H2 Fuel, Hong-Mei Yu, Zhong-Jun Hou, Bao-Lian Yi, Ke-Wan Bi, Jing-Xin Zhang, Zhi-Yin Lin, Ming Han

Journal of Electrochemistry

Fuel of proton exchange membrane fuel cell(PEMFC) mostly comes from reformatecontains CO which will poison the fuel cell electrocatalyst. The effect of CO on the performance of PEMFC was studied in this paper. The results of the experiment show that when CO is fed inPEMFC ,the cell voltage will be decreased violently,then it will become steady with some vibration. The poison will become more serious with higher CO content and weaker at higher temperature. The adsorption of CO on the electrocatalyst is reversible. The PtRu electrocatalyst is moresuitable for the electrocatalysis of CO/H₂ than Pt electrocatalyst.

Atmospheric Corrosion Of Steels In China, Cai-Feng Liang

Journal of Electrochemistry

Data of eight year atmospheric exposures of 17 steels at 7 sites in China were analyzed. The result showed that the most detrimental pollution is sulfur dioxide and chloride ion for corrosion of carbon steels and low alloy weathering steels. This is in accordance with the common knowledge.The effect of sulfur dioxide is serious in the first few years and becomes weak obviously in the later years. The environment factor of humid hot is much more important in long run than the ordinarily acknowledged humidity, pollution for non weathering steels,although it is not obvious in the beginning. If pollution were …

Properties Of Metallized Polyo-Toluididemembrane Modified Electrode, Li-Zong Dai, Yi-Ting Xu, Hui-Huang Wu

Journal of Electrochemistry

The platinum particles were electrodeposited on poly(o-toluidide), POT, modified electrode, and the surface configuration and crystal orientation of Pt particles were investigated by SEM and XRD. At the same time the oxidation of isopropanol on platinized POT modified electrode was studied. The results indicate that Pt particles deposite towards preferred-orientation; moreover the increase in polymer electroactivity due to proton doping affects the dimension and graininess of deposited Pt particles. At the metallized polymer electrode the oxidation of isopropanol can occur in POT electroactive potential region, however at the more positive than 0.70 V (SCE) potential where POT loses redox activity …

Galvanic Corrosion Of Tin-W Electro-Couple During Tungsten Chemical Mechanical Polishing, Xuan Cheng, Chang-Jian Lin

Journal of Electrochemistry

Chemical mechanical polishing (CMP) is a process whereby mechanicaland chemical forces are combined to remove material from a wafer and polish it to a flatsurface. Tungsten CMP is an important prcess to gain the global planarity of siliconwafers with tungsten (W) plugs. Tungsten is actually deposited on a thin adhesive layerof titanium nitride (TiN) on silicon. When close to the final stage of polishing, TiN and W will be simultaneously exposed to the polishing chemistry, forming a galvaniccouple. The corrsion of TiN and W couple will result in different polish rate.

Electrochemical Behavior Of Tinicu Shape Memry Alloy In Simulated Body Fluid, Cheng-Hao Liang, Hong-Yan Sui

Journal of Electrochemistry

The study of TiNiCu shape memory alloys (SMA) in Hank's simulated body fluidwas carried out. The results showed that narrow passive range was found in acid environment andactive anodic dissolution was discovered at 100~150 mV vs SCE on anodic polarization cure ofTiNiCu SMA. Temperature had little effect on anodic polarization. With the decrease of pH andthe increase of Cl^- concentration ,pitting corrosion potential (E_b) shifted negatively. The electrochemical capability of TiNiCu SMA was inferior to that of TiNi SMA. Observations by means ofXRD and SEM indicate that TiNiCu SMA is not in single crystal structure, which caused …

Study Of The Oxidation Dynamics Of Tizro2 Metal-Ceramics, Wen-Chao Li, Li-Dong Teng

Journal of Electrochemistry

The oxidation dynamics of hot-pressed Ti-ZrO₂ metal-ceramics with the compositionof 50 vol.% Ti and 50 vol.% ZrO₂ has been studied.Thermodynamic analysis shows that Ticould react with O₂ but not with N₂ in the oxidizing process of TiZrO₂ composites at 0.1 MPa air. The oxidation dynamic behavior of Ti-ZrO₂ composites is analogous to that of pure Ti. Theactivation energy for the oxygen diffusion in Ti-ZrO₂ composites is higher than that in Ti solutions, for the presence of ZrO₂ restrains the oxygen diffusion in Ti-ZrO₂ composites. At early stagethe oxidation of Ti-ZrO_{2 …}

Preparation And Properties Of Separator For Lithium-Ion Battery, Xu-Mei Ren, Feng Wu, Chuan Wu, Han-Jun Li, Xue-Jie Huang

Journal of Electrochemistry

Lithium-ion batteries are well adapted to the new multimedia applications. PP/PE based microporous film is commonly used as separator in commercial lithium ion batteries. Herewe report a microporous film which is superior to the commercial available separator. The microporous PVDF polymer separators were prepared by the phase inversion process. The pore size of the separator is Φ 7 μm , and it's porosity is 75 %. The membrane in LiPF₆-EC/DEC showedhigh ionic conductivity (above 10^-3 S/cm at room temperature), and good mechanical properties(10³ kg/cm²). The half-cells consisted of Li/PVDF separator/MCMB showed excellent cyclingcharacteristics and …

The Effect Of Calcium On The Properties Of Molybdenum Nitride Electrode, Yun-Gui Zhu, Xue-Liang Li, Dao-Rong Lu, Jian-Bo He, Ji-Huai Xia

Journal of Electrochemistry

The effect of calcium on the properties of molybdenum nitride film electrode wasstudied by using XRD, SEM and cyclic voltammetry. The results show that the specific electriccapacity and the voltage operating range of electrode vary with the concentration of additive in thedipping solution. At the optimum concentration of additive in the dipping solution, the specificelectric capacity of the electrode is 2.1 times as large as that of the electrode prepared in the dipping solution without additive, and the voltage operating range of electrode is increased by 0.11 V. The active mechanism of calcium on the properties of film electrode suggested …

Corrosion Behavior Of Titanium In Fgd System, J-C Lin, T-L Chang, C-T Dung, S-L Lee, S-D Chyou, S-D Guo

Journal of Electrochemistry

In-situ corrosion test of titanium in flue gas desulfurization(FGD) system has been studied. Specimens of commercial Ti alloy have been put in four different locations (i. e , cooler, pre-scruber, absorber and heater) of the FGD system for 271 days. The corrosion rate is very low (i.e.<1 mpy) in all locations. Almost no corrosion can be found in the prescruber(0 mpy), but a sensible corrosion rate is estimated in the heater (0.58 mpy). Examination through SEM, all the specimens are subject to pitting corrosion except those in the prescruber. ESCA analysis indicates that the surface film for the specimen in prescruber is calcium carbonate, but titanium nitrate for the specimen in heater. Cyclic anodic potentiodynamic polarization (CAPP) of titanium in aerated and deaerated green solution provides an interpretation on the corrosion behavior of the titanium in the FGD system.

Performance Of A Direct Methanol Fuel Cell, Zhao-Bin Wei, Jian-Guo Liu, Ya-Guang Jiao, Wei-Jiang Zhou, Wen-Zhen Li, Li-Kang Chen, Qin Xin, Bao-Lian Yi

Journal of Electrochemistry

A direct methanol fuel cell with 9cm² active area consists of Pt-Ru/C anode ,Pt/Ccathode and Nafion 115 membrane. The effect of operating conditions: methanol solution concentration, oxygen pressure and cell temperature on the cell performances was investigated. The results show that performance of single cell was enhanced by increasing oxygen pressure and celltemperature ,and a maximum power density 75 mW/cm² was obtained in the range of 250-300mA/cm² current density, 0.2 MPa oxygen pressure, 1.0 mol/L methanol concentration and 75 ℃ cell temperature. When cell operating at room temperature, a relatively low, but a stable performance of cell …

The Effect Of Preparation Condition On The Photoelectrochemical Performance Of Both The Pani Film And Tio2-Pani Composite Film On Au, Huai-Guo Huang, Hong-Ping Zhang, Zhi-Xin Zheng, Yan-Yan Xi, Ling-Ling Wu, Zhong-Hua Lin

Journal of Electrochemistry

Both the PANI (polyaniline) film and TiO₂-PANI composite film on the PATP(paminothiophenol)/Au substrate were obtained under different preparation condition by electrochemical methods, and their photoelectrochemical performances were alo studied. The resultsshowed that the photoelectrochemical performances of the films depend deeply on the comditionsof preparation. The self-assembling of PATP favors the adhesion of PANl. The partially-oxidizedPANI has a greater photoelectrochemical response than that of the reduced PANI and oxidized PANl. There is an optimum of film thickness for the photoelectrochemical performance of PANI film. Heat treating is in favor of the photoelectrochemical performance of TiO₂, but decreases …

Study On Corrosion Resistance Of Electroless Nickel Composite Coatings, Tsong-Jen Yang, Meng-Feng Jou

Journal of Electrochemistry

The eletroless nickel composite coating was prepared by uniform dispersion of diamond (or PTFE) particles throughout electroless nickel deposition. Corrosion resistance of composite coating in 3.5% NaCl aqueous solution was investigated by electrochemical analysis, dipping test and salt spray test. The results showed that the corrosion resistance of composite coating was inferior to that of electroless nickel coating if small amount of particles was added to the composite coating. Microsturctural analysis by SEM, AES, XRD, and EPMA indicated that the distribution of phosphorus is not homogeneous in the composite coating. The phosphorus_rich region acts as microcathode, however, the phosphorus-lean region …

Preparation Of Ti-Based Nanocrystalline Tio2 Film Electrode With High Activity, Dao-Bao Chu, Guang-Xia Shen, Xing-Fu Zhou, Chang-Jian Lin, Hua-Shui Lin

Journal of Electrochemistry

The potentiostatic electrosynthesis of Ti(EtO)₄ was studied by anodic dissolution of metal titanium(TA1) in solution of 0.005 mol·L^-1 (EtO)₄NBr in the ethanol (AR) in the presence negligible CH₃COCH₂COCH₃. The Ti-based nanocrystalline TiO₂ Film electrode (Ti/nano-TiO₂) was prepared by sol-gel method. By TEM, SEM and XRD, it has been shown that the anatase particle of TiO₂ was 10～35 nm in diameter and the film was 0.5 μm in thickness. The nanocrystalline film was composed of a three-diminsional network of interconnected particles. Reodx behavior and electrocatalytic activities of …

New Progress In Studies Of Lithium Nickel Oxide As Positive Electrode Materials Of Lithium Ion Batteris, Han-San Liu, Yong Yang, Zhong-Ru Zhang, Zu-Geng Lin

Journal of Electrochemistry

Lithium nickel oxide as the positive electrode of lithium ion batteries has aroused more and more interests.This paper reviews the recent reserches on synthesis and element-substitution of LiNiO₂ cathode material,and summarizes the intrinsical relationship between properties and sturcture of the material.The developments of new synthesis methods and mutilsubstitution of the material are expecting to be studied in the future research.

Electrochemistry Characteristic Of Carbon Steel Under Biofilm And Sulfide Film, Ze-Hua Dong, Xing-Peng Guo, Jia-Shen Zheng, Li-Ming Xu

Journal of Electrochemistry

Wire Beam Electrode (WBE) made of Q235 carbon steel was applied to study theheterogeneous corrosion beneath biofilm formed by Sulfate Reducing Bacteria (SRB) in cultureand sulfide film in solution with 1% NaCl and 300 mg/L⋅S^2-. The potential, galvanic density mapping, as well as polarization curve and Electrochemical Impedance Spectrum (EIS) were measured to predict the localized corrosion under biofilm and sulfide film. As a result, the mappingshowed the potential fluctuation on the WBE suface decreased over time due to the conductivityof the biofilm and sulfide film. Therefore, the potential mapping could not be a criterion of localized corrosion …

Factors Affecting The Quality Of Dry Shotcrete, El Rasheid Mohamed Abdalla El Khidir

Archived Theses and Dissertations

No abstract provided.

On Multifunctional Collaborative Methods In Engineering Science, Jonathan B. Ransom Sr.

Mechanical & Aerospace Engineering Theses & Dissertations

Engineers are challenged to produce better designs in less time and for less cost. Hence, to investigate novel and revolutionary design concepts, accurate, high-fidelity data must be assimilated rapidly into the design, analysis and simulation process. This data assimilation should consider diverse mathematical modeling and multi-discipline interactions necessitated by concepts exploiting advanced materials and structures. Integrated high-fidelity methods with diverse engineering applications provide the enabling technologies to assimilate these high-fidelity, multi-disciplinary data rapidly at an early stage in the design. These integrated methods must be multifunctional, collaborative and applicable to the general field of engineering science and mechanics.

Multifunctional methodologies …

Computational Investigation Of Aeromechanical Hcf Effects In A Compressor Rotor, Andrew L. White

Theses and Dissertations

High-Cycle Fatigue is a major problem facing the gas turbine industry today. It has been investigated by many researchers, using many different methods. Due to its highly complex nature, designers still do not have adequate tools to accurately predict the onset of high-cycle fatigue. A three-dimensional Navier-Stokes program was used to perform a study of the unsteady aerodynamics on a compressor rotor. The effect of aerodynamic detuning on the forced response of a rotor blade was compared to a baseline tuned rotor case. Detuning consisted of a ten percent decrease in circumferential spacing between alternate pairs of blades. The high-cycle …

Fatigue Response Of Thin Stiffened Aluminum Cracked Panels Repaired With Bonded Composite Patches, Jason B. Avram

Theses and Dissertations

This research investigated the fatigue response of precracked and patched 2024-T3 Aluminum panels with stiffeners. Patches were single-sided, unidirectional three ply boron/epoxy. Stiffeners were 2024-T3 aluminum and were riveted and bonded on. Disbonds were introduced into the repair bondline by inserting teflon strips. Three disbond configurations were investigated rack tip disbond (CTD) located at the edge of the patch in the path of crack propagation, full-width disbond (FWD) covering the entire crack, and end disbond (ED) located at each end of the patch and covering the full width. Each repaired panel was subjected to tension/tension cyclic fatigue with a maximum …

Modification Of Position And Attitude Determination Of A Test Article Through Photogrammetry To Account For Structural Deformation, Sean A. Krolikowski

Theses and Dissertations

This study improved the current method of position and attitude determination to account for structural deformation of the wind tunnel test article due to aerodynamic loading. To account for deformation, parabolic bending and linear twisting coefficients were added into the Levenberg-Marquardt multi-parameter solver. By accounting for deformation, the accuracy of position and attitude determination was greatly improved. This study also takes a qualitative look at the optimum number of wind tunnel cameras and model targets. Optimal configuration was found to be around 50 targets and 2 cameras offset by 90 degrees.

The Development Of A Finite Element Program To Model High Cycle Fatigue In Isotropic Plates, William C. Shipman

Theses and Dissertations

As part of a joint AFRL/DAGSI turbine blade research effort, a computer program has been developed that uses a von Karman large-deflection two-dimensional finite element approximation to determine stress levels and patterns in isotropic thin plates. The dynamic loading of various plates has been carried out in order to model a high cycle fatigue situation. The research considered the various effects of mode shapes, resident frequency, non-linear cyclic effect, endurance limits, and stress variations within a high cycle fatigue environment. Two main initiatives were taken. First, a transient analysis tool was developed that calculates stress and displacement patterns over a …

The Applications Of Confocal Raman Micro-Spectroscopy For Study Of Practical Electrode Materials, Yong Yang, Wei Chu, Jun-Min Nan, Xun-Guang Chen, Zu-Geng Lin

Journal of Electrochemistry

Some recent research work about applications of confocal Raman micro spectroscopy for study of practical electrode materials carried out in our lab has been briefly introduced. The examples include study of electrochemical Li⁺ intercalation process, characterization of surface oxide film on AB₅ type electrodes and passive film and pitting corrosion of Rebar electrodes.

A Study On The Performance Of Matrix Prepared By Tape Cast And Its Molten Carbonate Fuel Cells (Mcfcs), Hua-Xin Lin, Bao-Lian Yi, Li Zhou, Chang-Qing He, Lian-Ying Kong, En-Jun Zhang

Journal of Electrochemistry

The matrix prepared with γ-LiAlO₂ powder and by tape cast displayed higher ability of preventing from gas cross over and lower ohmic polarization. The voltages of the stack (three cells, 122 cm²) stacked with the matrix were 2.02 and 1.78 V at 200 and 246 mA/cm², respectively, and the output power reached 53.4 W. The cell (28 cm ²) voltages were 0.85 and 0.75 V at 200 and 300 mA/cm², respectively, and the output power was about 6.6 W. Compensating the shrinkage of matrix in stacking cells promoted the enhancement of the …

Two-Dimensional Surface Raman Imaging Of A Roughened Iron Electrode In Saline Water, Pei-Gen Cao, Jian-Lin Yao, Jun-Wei Zheng, Bin Ren, Ren-Ao Gu, Zhong-Qun Tian

Journal of Electrochemistry

The analysis of the composite and distribution of iron oxide due to pit corrosion in saline solutions (3.4% NaCl) is of great importance. Many electrochemical methods, XPS, and other photoelectronic techniques have been applied to this domain. Surface enhanced Raman scattering (SERS) spectroscopy can provide the vibrational information of surface species with high sensitivity and is very useful in the study of surface chemistry of iron. Notwithstanding, the application of SERS in iron corrosion is hampered for its SERS-inactivity. Efforts have been devoted to extend the use of SERS to the study of iron.

How Can Direct Mthanol Fuel Cell Benefit From Carbonate Media, Lin Zhuang, Yang Wang, Jun-Tao Lu

Journal of Electrochemistry

The kinetics of methanol oxidation and oxygen reduction in 0.5 mol/L K₂CO₃ were compared with those in 0.5 mol/L H₂SO ₄. Experiments revealed that carbonate media could be more beneficial to direct methanol fuel cell(DMFC). Firstly, both electrode reactions show better performance in the carbonate than in the acid; secondly, materials other than noble metals become possible to be used as the anodic and cathodic catalysts; thirdly, the potential dectease caused by methanol crossover could be depressed by using metal oxide catalysts not stable in acid, such as MnO₂.

Synthesis Of Limn2O4-ΔClΔ Cathode Material By Like-Sol-Gel Methode, Zhao-Yong Chen, Yi He, Xing-Quan Liu, Zhi-Jie Li, Zuo-Long Yu

Journal of Electrochemistry

LiMn₂O_4-δCl_δ was synthesized by like sol gel methode, with calculated LiOH·H₂O, Mn(No₃)₂⋅6H₂O and LiCl·H₂O, and made electrochemical test with these compounds as positive materials. Result demostrated that LiMn₂O_4-δCl_δ cathode material has exellent stability and nearly no capacity loss after reaching stability.

In Situ Raman Spectroelectrochemical Characterization Of The Prussian Blue/Platinum Modified Electrode, Xiao-Wei Cao, Rong Wang, Gui-Hua Wang, Zong-Rang Zhang

Journal of Electrochemistry

Prussian Blue is known to be deposited electrochemically on the electrode surface, producing a dense redox active layer. Since the Prussian Blue modified electrode was first reported by Neff in 1978, different in situ spectroelectrochemical techniques have been widely used to investigate its electrochemical mechanism. But no research work related to the in situ Raman spectroscopic studies on it has been reported. In this paper we try to characterize the nature of thin Prussian Blue films on platinum substrates with in situ Raman spectroelectrochemical technique.

Adsorption Behavior Of Co At The Ultrathin Rh And Pt Film Electrodes, Yong Xie, Xiao-Qin Li, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Pt group metals have been widely used in catalysis such as hydrogenation of organic compounds and the oxidation of carbon monoxide. The information about CO adsorption on the Pt group surfaces and the influence of other surface species, such as hydrogen and CO₂ will be greatly helpful to elucidate the adsorption behavior of CO on Pt group metal surfaces and get a deeper understanding of catalytic mechanisms of Pt group metals. Surface enhanced Raman spectroscopy (SERS) has been becoming an increasingly important means to characterize the electrochemical metal solution interface over the past two decades. Our laboratory has successfully …

Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode Ii. Eqcm And In-Situ Ftir Spectroscopic Studies In Acid Media, Guo-Liang Chen, Sheng-Pei Chen, Zhi-You Zhou, Chun-Hua Zhen, Shi-Gang Sun

Journal of Electrochemistry

The adsorption and oxidation of ethanol on nm Pt/GC electrode in acid solutions containing 0.1 mol·L ^-1 H₂SO₄ +0.1 mol·L ^-1 CH₃CH₂OH was investigated by using cyclic voltammetry, EQCM and in situ FTIR spectroscopy. The experimental results demonstrated that the oxidation of CH₃CH₂OH is closely relaed to solution acidity and oxygen species on electrode surface; CH₃CH₂OH was oxidized on nm Pt/GC electrode in acidic media via a dual path reaction mechanism, i.e . CH₃CH₂OH may be oxidized into CO₂ through …