Engineering Science and Materials | Open Access Articles

Using Shrimp Shells As Based Catalysts For Fame Production From Palm Oil Feedstock, Assadaporn Poonanan, Anupat Prukpaiboon, Paul Egwuonw Dim, Mutsee Termtanun

Journal of Metals, Materials and Minerals

In this study, waste shrimp shells from industry were used as a heterogeneous bio-based catalyst for trans-esterification reaction of fresh palm oil. CaO was prepared from shrimp shells calcination. Surface area, phase composition, and basicity of the calcined shrimp shell catalysts were studied using N2 adsorption (BET), X-ray diffraction (XRD), and CO2 temperature-programmed-desorption (CO2-TPD), respectively. The influence of shrimp shells calcination temperature and operation condition, methanol to palm oil ratio on trans-esterification reaction, were investigated. Five hours trans-esterification was carried out at 65℃ using different shrimp shell at four different calcination temperature: 700, 750, 800 and 850℃ with 9:1 methanol …

Go to article

Investigation Of Deposition Parameters On The Structural Properties And Hardness Of Tialn Films Deposited Via Reactive Pulsed Dc Magnetron Sputteringinvestigation Of Deposition Parameters On Structural Properties And Hardness Of Tialn Films Deposited By Reactive Pulsed Dc Magnetron Sputtering, Jariyaporn Rukkun, Kamon Aiempanakit, Pimchanok Reakaukot, Witthawat Wongpisan, Kirati Waree, Montri Aiempanakit

Journal of Metals, Materials and Minerals

In this work, titanium aluminum nitride (TiAlN) films were deposited on a silicon substrate via reactive pulsed DC magnetron sputtering. The effect of deposition parameters such as nitrogen gas flow rate, substrate temperature, and bias voltage on the structural and mechanical properties of TiAlN films was investigated. The crystal structure, morphology, and hardness of TiAlN films were characterized via X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM, and nanoindentation. An improved crystallinity of TiAlN films was obtained by varying the substrate temperature and bias voltage. The morphology of the TiAlN film exhibited a columnar structure, and the morphology gradually …

Go to article

Improving Corrosion Resistance Of 3d Printed Ti-6al-4v By Tin Coating, Surada Nisaimun, Phitsanu Poolcharuansin, Patama Visuttipitukul, Pitichon Klomjit

Journal of Metals, Materials and Minerals

TiN thin films were deposited on biomaterial 3D printed Ti-6Al-4V substrates using two methods including direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS). The coating times were compared between 5 min and 25 min. HiPIMS was developed based on DCMS by increasing degree of ionization in plasma and power densities in the order of kWcm-2 compared to Wcm-2 of DCMS. The film characteristics and mechanical properties were investigated by glancing incident x-ray diffractometer (GIXRD), field emission scanning electron microscope (FE-SEM), and atomic force microscope (AFM). Electrochemical behavior was analyzed by electrochemical impedance spectroscopy (EIS) in 1 M …

Go to article

Characteristic Of Fluorescence Spectroscopy Response Of Tetrakis (4-Sulfonatophenyl) Porphyrin Doped Polyaniline Toward Fe3+ Ion, Chatr Panithipongwut Kowalsk, Meatawadee Buntee, Prasit Pattananuwat

Journal of Metals, Materials and Minerals

Here, we report a selective colorimetric chemosensor toward Fe3+ ion detection by the combination of sensitizer and hole transport consisting of polyaniline and tetrakis (4-sulfonatophenyl) porphyrin. Interestingly, the presence of tetrakis (4-sulfonatophenyl) porphyrin moiety on polyaniline can enhance the optical limiting properties of polyaniline, allowing the fluorophore signal for chemical sensor. The performance sensing behaviors toward metal ion are observed by the ultraviolet-Visible and fluorescence properties. The sensing of polyaniline-tetrakis (4-sulfonatophenyl) porphyrin toward Fe3+ ion exhibits a linear response in the concentration range of 0.01 M to 1.0 × 10-4 M over the other transition metals (Cu2+, Ni2+, Zn2+, Pb2+, …

Go to article

The Study On Un-Doped/Boron Doped/Un-Doped Triple Seg In Vertical Nand Flash Memory, Woong Lee, Chaeho Kim, Joonsuk Lee, Sehun Park, Yonghan Roh

Journal of Metals, Materials and Minerals

Selective epitaxial growth (SEG) plays a critical role in vertical NAND flash memory because it serves as a ground select line (GSL) transistor, which is used to control the cell current in the vertical channel. In this study, different channel hole sizes between the adjacent hole and away hole from the common source line (CSL) were detected after vertical channel etch (VCE). This discrepancy severely impacts the boron concentration of SEG applied through ex-situ boron implantation, and results in large GSL Vth variations. Novel in-situ boron-doping of triple-layered un-doped/boron doped/un-doped SEG was developed to solve the high variation of the …

Go to article

Microwave-Assisted Ecofriendly Silver Nanoparticle Synthesis By Varieties Of Chrysanthemum Morifolium Ramat: Assessing Their Antioxidant, Photocatalytic And Antibacterial Activities, Mathivathani Kandiah, Laknee Nawamali De Silva

Journal of Metals, Materials and Minerals

Based on recent developments in the field of Nanobiotechnology, this study is aimed at the assessment of antioxidant, photocatalytic and antibacterial activities of silver nanoparticles (AgNPs) synthesized using Chrysanthemum morifolium Ramat varieties (brown, yellow, purple, pink, salmon pink and white), where five varieties produced AgNPs except white. Antioxidant assays such as total flavonoid content, total phenolic content and total antioxidant capacity and free radical scavenging assays such as ferric reducing antioxidant power and DPPH radical scavenging assays were performed. Photocatalytic activity was assessed by the degradation of the model dye methylene blue. Anti-bacterial activity was determined on Staphylococcus aureus and …

Go to article

Improvement Of The Superconducting Properties Of Carbon Addition On Bi1.6pb0.4sr2 Ca2cu3o10+Δ Prepared Through The Two-Step Sintering Process, Dini Rizqi Dwikunti Siregar, Sigit Dwi Yudanto, Septian Adi Chandra, Eka Feby Ronauli Lubis, Syahrul Humaidi, Nono Darsono

Journal of Metals, Materials and Minerals

The effects of the addition of carbon nanoparticles and nanotubes on the Bi1.6Pb0.4Sr2Ca2Cu3O10+δ (BPSCCO) have been reported. BPSCCO samples were synthesized using the sol-gel method. BPSCCO with nominal composition was sintered at 840°C for 30 h, then grounded and added an amount of carbon. Pure and carbon added BPSCCO were sintered at 840°C for 30 hours. Resistivity measurements were carried out to determine the superconducting properties of the samples. We found that the addition of carbon nanoparticles and nanotubes increased the critical zero temperature (Tc-zero) of BPSCCO from 94.67 K to 97.8 K and 102.03 K for the pure BPSCCO, …

Go to article

Stress Softening Characteristics Of Thin Monoholar Rubber Flat Slab, Kulyuth Boonseng, Chatchai Waiyapattanakorn, Prayoon Surin

Journal of Metals, Materials and Minerals

Thin monoholar rubber flat slab gives rise to unconventional mechanical properties under tension loading not found in thin solid rubber flat slab. However there has been no proper report on its stress softening characteristics. Stress softening is an important phenomenon occurring in all elastomeric materials under cyclic tension loading. Parameters pertinent to stress softening investigated in this research are stress-strain characteristics, permanent set strain and hysteresis loss energy of the thin monoholar rubber flat slab in comparison with the thin solid rubber fat slab when undergoing 7 cycles of stretching. Noticeable differences of stress-strain hysteresis loops diminution of the thin …

Go to article

Photoelectrochemical Cathodic Protection Of Amorphous Zinc Oxide Coating On Hot Rolled Steel Ss400 In A 3 Wt% Nacl Solution And A Na2s-Naoh Solution, Phatchara Wipataphan, Worapot Sripianem, Naw Blessing Oo, Thanate Na Wichean, Boossayamas Dachbumroong, Oratai Jongprateep, Gasidit Panomsuwan, Naray Pewnim, Ratchatee Techapiesancharoenkij

Journal of Metals, Materials and Minerals

The photoelectrochemical cathodic protection of amorphous ZnO thin-film coating on hot rolled steel SS400, in the 3 wt% NaCl environment, was investigated. The ZnO thin film was coated on a SS400 substrate at 200℃ using the spray pyrolysis technique. The x-ray diffractometry analysis confirmed the amorphous ZnO coatings. Two different types of the electrochemical cells were used: a single-cell and a double-cell system. Two different types of the photoelectrolytic solutions were compared: (i) 0.1 M Na2S + 0.2 M NaOH and (ii) 3 wt% NaCl solution. The ZnO-coated SS400 samples were subjected to potentiostatic polarization testing under dark and UV …

Go to article

Influence Of Graphite Feedstock On The Characteristics Of Silver-Decorated Graphene Oxide And Antimicrobial Property, Ebrahim Mahmoudi, Wei Lun Ang, Gasidit Panomsuwan, Oratai Jongprateep, Abdul Wahab Mohammad, Law Yong Ng, Muneer M. Ba-Abbad

Journal of Metals, Materials and Minerals

Graphite from different sources has significant influence on the properties of graphene oxide (GO) and reactivity of GO towards further modification with other nanoparticles. However, such effect has not yet been properly explored. This study aims to investigate the characteristics and antimicrobial property of GO decorated with silver nanoparticles (known as Ag-GO composite) where the GO is synthesized via modified Hummer’s method from various graphite feedstock, namely natural graphite flake (NGF), natural graphite powder (NGP), and synthetic graphite powder (SGP). The Ag-GO nanocomposite was then synthesized using chemical reduction methods. Antimicrobial properties of the Ag-GO were tested using the standard …

Go to article

Preparation Of A Mixed Al/Sc Nano-Oxide Derived From The Bauxite Residue (Red Mud) Via The Sulfuric Acid Roasting–Leaching–Precipitation Process, Razieh Habibpour, Eslam Kashi, Mehdi Janfada

Journal of Metals, Materials and Minerals

In this study, three methods were used and compared for the selectable extraction of aluminum/ scandium with the least amount of iron in red mud (RM) samples from the Iran alumina plant in Jajarm as follows: 1) RM direct acid leaching with H2SO4, 2) RM washing with hydrochloric acid and oxalic acid before leaching with H2SO4, and 3) RM sulfuric acid roasting-leaching-precipitation. The aim was to extract the highest amount of scandium while preventing the leaching of other metals, especially iron. Due to any discriminative features, the selective separation of Al/Sc with …

Go to article

Interface Characterization In Tungsten Fiber/Zr-Based Bulk Metallic Glass Matrix Composite, Mohammad Ammar Mofid, Mostafa Jafarzadegan

Journal of Metals, Materials and Minerals

In this research, Zr55Cu30Al10Ni5 bulk metallic glass (BMG) alloy is used as the base material to form tungsten fiber reinforced BMG composites. The composites are synthetized using melt infiltration casting method and their microstructure and compressive properties are investigated. Two different infiltration times of 10 min and 15 min are used to produce the composites. The microstructural evaluation of the interface between tungsten fiber and BMG matrix reveals that a narrow reaction band emerges between the tungsten wires and BMG alloy. Some portions of this layer are broken into the fine Zr/W-rich particles …

Go to article

Engineering Science and Materials Commons^™

Full-Text Articles in Engineering Science and Materials

Using Shrimp Shells As Based Catalysts For Fame Production From Palm Oil Feedstock, Assadaporn Poonanan, Anupat Prukpaiboon, Paul Egwuonw Dim, Mutsee Termtanun

Journal of Metals, Materials and Minerals

Journal of Metals, Materials and Minerals

Improving Corrosion Resistance Of 3d Printed Ti-6al-4v By Tin Coating, Surada Nisaimun, Phitsanu Poolcharuansin, Patama Visuttipitukul, Pitichon Klomjit

Journal of Metals, Materials and Minerals

Characteristic Of Fluorescence Spectroscopy Response Of Tetrakis (4-Sulfonatophenyl) Porphyrin Doped Polyaniline Toward Fe3+ Ion, Chatr Panithipongwut Kowalsk, Meatawadee Buntee, Prasit Pattananuwat

Journal of Metals, Materials and Minerals

The Study On Un-Doped/Boron Doped/Un-Doped Triple Seg In Vertical Nand Flash Memory, Woong Lee, Chaeho Kim, Joonsuk Lee, Sehun Park, Yonghan Roh

Journal of Metals, Materials and Minerals

Microwave-Assisted Ecofriendly Silver Nanoparticle Synthesis By Varieties Of Chrysanthemum Morifolium Ramat: Assessing Their Antioxidant, Photocatalytic And Antibacterial Activities, Mathivathani Kandiah, Laknee Nawamali De Silva

Journal of Metals, Materials and Minerals

Improvement Of The Superconducting Properties Of Carbon Addition On Bi1.6pb0.4sr2 Ca2cu3o10+Δ Prepared Through The Two-Step Sintering Process, Dini Rizqi Dwikunti Siregar, Sigit Dwi Yudanto, Septian Adi Chandra, Eka Feby Ronauli Lubis, Syahrul Humaidi, Nono Darsono

Journal of Metals, Materials and Minerals

Stress Softening Characteristics Of Thin Monoholar Rubber Flat Slab, Kulyuth Boonseng, Chatchai Waiyapattanakorn, Prayoon Surin

Journal of Metals, Materials and Minerals

Journal of Metals, Materials and Minerals

Influence Of Graphite Feedstock On The Characteristics Of Silver-Decorated Graphene Oxide And Antimicrobial Property, Ebrahim Mahmoudi, Wei Lun Ang, Gasidit Panomsuwan, Oratai Jongprateep, Abdul Wahab Mohammad, Law Yong Ng, Muneer M. Ba-Abbad

Journal of Metals, Materials and Minerals

Preparation Of A Mixed Al/Sc Nano-Oxide Derived From The Bauxite Residue (Red Mud) Via The Sulfuric Acid Roasting–Leaching–Precipitation Process, Razieh Habibpour, Eslam Kashi, Mehdi Janfada

Journal of Metals, Materials and Minerals

Interface Characterization In Tungsten Fiber/Zr-Based Bulk Metallic Glass Matrix Composite, Mohammad Ammar Mofid, Mostafa Jafarzadegan

Journal of Metals, Materials and Minerals