Engineering Science and Materials Commons^™

Greek Key-Inspired Fractal Metamaterials With Enhanced Flexibility And Energy Absorption., Zhennan Zhang

Electronic Theses and Dissertations

Architected materials with intricate three-dimensional (3D) geometries offer unique properties and functionalities but face challenges in manufacturing costs and complexity. This research explores the integration of simple 2D Greek Key-inspired lattices into fractal designs to achieve exceptional mechanical performance. Using 3D printing and kerfing, these fractal structures demonstrate enhanced flexibility and energy absorption capabilities. Through three-point bending and in-plane tensile tests, the 2D fractal lattices exhibited a 600-fold reduction in bending force and a tensile stretch capacity of up to 520%, significantly outperforming brittle parent materials. Out-of-plane compression tests revealed a five-fold increase in energy absorption compared to honeycomb structures, …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Additive Manufacturing Of Aluminum Alloy By Metal Fused Filament Fabrication (Mf3)., Luke J. Malone

Electronic Theses and Dissertations

This research studies metal-fused filament fabrication (MF3) for manufacturing aluminum alloy parts. An aluminum alloy powder-based feedstock with a polymer-binder system was extruded via capillary rheometry to form a filament. The filament was used to print green parts that were involved in a two-step debinding process combining solvent and thermal extraction of the polymer binder, then sintered in a partial vacuum. Resulting grain structure, sintered density, and mechanical properties will be characterized and compared to metal injection molded (MIM) specimens. The main objective is to gain an understanding of the MF3 process characteristics and the ensuing material properties and microstructure …

Mechanical Property Evaluation Of Additively Manufactured Materials Across A Wide Temperature Range, Sanket Vinayak Hirve

Electronic Theses and Dissertations

Additive manufacturing (also called 3d printing) has transitioned from a prototyping-only technology to a technology that is able to create usable parts with complex geometries. 3D printed parts are beginning to be used across all areas of engineering, such as biomedical, aerospace, automobile and many more. Typically, the term “3D printing” refers to layer by layer deposition of polymer materials, while the term “additive manufacturing” refers to layer by layer metal deposition. Conventional manufacturing, or substrative manufacturing, has several main problems that additive manufacturing can help overcome, such as high cost for low volume production, inability to create very complex …

Optical Direct Detection Of Thermal Vibrations Of Ultralow Stiffness Micro-Nano Structures., Sri Sukanta Chowdhury

Electronic Theses and Dissertations

A direct detection optical vibrometer is constructed around an 850 nm laser and a quadrant photodetector (QPD). The limit of detection is 0.2 fW which corresponds to a minimum amplitude of 0.1 Å. The vibrometer is used to measure the thermal vibration spectra of low stiffness micromechanical structures have nanometer features. One structure measured is a cantilevered 30 μm diameter glass fiber. Vibration amplitudes as low as 1.1 Å are measured. The thermal vibration spectra show fundamental resonances at 80-250 Hz and a signal to noise ratio (SNR) of 23-55 dB. Young’s modulus of glass in the cantilevers, estimated from …

Lithium Polysulfide Battery With Improved Capacity And Cycle Performance Using Carbon Black Coated Free-Standing Carbon Cloth, Zhen Wei

Electronic Theses and Dissertations

Lithium ion batteries (LIBs) have been used in various applications such as portable electronics, grid storages, and electric vehicles (EVs). Despite its commercial success, further advancement of the battery is necessary to satisfy the increasing demands for low-cost and high- performance energy storage devices as LIB is reaching its theoretical limits. Lithium sulfur battery (LSB) is one of the promising candidates for the next generation energy storage technologies. LSB uses sulfur cathode which is a low-cost and earth abundant material with an extremely high theoretical capacity of 2600 Wh kg-1. Although there have been numerous researches aiming to establish the …

Development Of S-Nitroso-N-Acetylpenicillamine (Snap) Impregnated Medical Grade Polyvinyl Chloride For Antimicrobial Medical Device Interfaces, Corbin Feit

Electronic Theses and Dissertations

In the clinical setting, polyvinyl chloride (PVC) accounts for 25% of all polymers used in medical device applications. However, medical devices fabricated with PVC, such as endotracheal tubes, extracorporeal circuits (ECCs), or intravenous catheters suffer from thrombosis and infection. Mortality associated with hospital associated infections (HAIs) exceed 100,000 deaths each year. One method to overcome these challenges is to develop bioactive polymers with nitric oxide (NO) release. Nitric oxide exhibits many physiological roles including, antibacterial, antithrombic, anti-inflammatory activity. In this study, Tygon® PVC tubing was impregnated with a NO donor molecule, S-nitroso-N-acetylpenicillamine (SNAP), via a simple solvent-swelling-impregnation method, where polymer …

Development Of In Vitro Point Of Care Diagnostics (Ivpcd) Based On Aptamers Integrated Biosensors, Nileshi Saraf

Electronic Theses and Dissertations

The global market for the medical diagnostic industry is worth 25 billion dollars in the United States and is expected to grow exponentially each year. Presently available methods for biodetection, such as immunoassays, chemiluminescence and fluorescent based assays are expensive, time consuming and require skilled labor with high-end instruments. Therefore, development of novel, passive colorimetric sensors and diagnostic technologies for detection and surveillance is of utmost importance especially in resource constrained communities. The present work focusses on developing novel and advanced in vitro biodiagnostic tools based on aptamer integrated biosensors for an early detection of specific viral proteins or small …

Interfacial Behavior In Polymer Derived Ceramics And Salt Water Purification Via 2d Mos2, Hao Li

Electronic Theses and Dissertations

In the present dissertation, the behavior of the internal potential barrier in a polymer-derived amorphous SiAlCN ceramic was studied by measuring its complex impedance spectra at various dc bias as well as different testing and annealing temperatures. The complex impedance spectra of the polymer-derived a-SiAlCN were measured under various dc bias voltages in a temperature range between 50 and 150°C, as well as different annealing temperatures (1100-1400 °C). All spectra, regardless of temperature and bias, consist of two semi-circular arcs, corresponding to the free-carbon phase and the interface, respectively. The impedance of the free-carbon phase is independent of the bias, …

Geothermal Resource Assessment Of Mississippi, Adam Blake Goodwin

Electronic Theses and Dissertations

Geothermal energy is exploited through the process of using hot water or steam extracted from reservoirs of geothermal heat in Earth's crust which is derived from the upward convection and conduction of heat from Earth’s mantle and core. This energy can be harnessed to power geothermal heat pumps, heat water, or to generate electricity. Previous geothermal assessments of Mississippi have been locally focused, either in the southern Mississippi River flood plains or in eastern north central Mississippi at an active lignite coal mine. The focus of this project was to calculate and map heat flow estimates within the entire state …

A Numerical Study Of Granular Dam-Break Flows, Nuttita Pophet

Electronic Theses and Dissertations

Granular flows are mass movements of mixtures of solid particles and interstitial fluid. Examples include landslides, debris flows and tailings dam-break flows. These types of flows are often catastrophic events, and cover a wide range of phenomena of interest to both scientists and engineers. The mechanical properties of granular materials and the hydraulic behavior of the flows originate from solid and fluid phases, their distribution and interaction. Understanding the behavior of these types of flows and developing reliable predictive models are important.

Nanoscale Spectroscopy In Energy And Catalytic Applications, Yi Ding

Electronic Theses and Dissertations

Emerging societal challenges such as the need for more sustainable energy and catalysis are requiring more sensitive and versatile measurements at the nanoscale. This is the case in the design and optimization of new materials for energy harvesting (solar cells) and energy storage devices (batteries and capacitors), or for the development of new catalysts for carbon sequestration or other reactions of interest. Hence, the ability to advance spectroscopy with nanoscale spatial resolution and high sensitivity holds great promises to meet the demands of deeper fundamental understanding to boost the development and deployment of nano-based devices for real applications. In this …

Theoretical And Experimental Study For Tailoring The Electromagnetic Properties Of Conductive Materials, Jeffrey Jennings

Electronic Theses and Dissertations

Induction in leaded, implanted medical devices exposed to radio frequency (RF) magnetic fields during magnetic resonance imaging (MRI) produce Joule heating in adjacent tissues causing various issues, including death. Given the importance of MRI as a diagnostic tool and the growth in leaded device-related treatments, identification of a solution ensuring their compatibility is of great interest. Electromagnetic (EM) surface property tailoring in lead materials to change their inductive response by adding functionally-graded, heterogeneous surface layers is a possible solution. However, non-uniform EM properties introduce two challenges: the added complexity of analyses and characterization of the graded region. This dissertation addresses …

Analysis Of Residual Stress And Damage Mechanisms Of Thermal Barrier Coatings Deposited Via Ps-Pvd And Eb-Pvd, Linda Rossmann

Electronic Theses and Dissertations

Thermal barrier coatings (TBCs) are critical to gas turbine engines, as they protect the components in the hot section from the extreme temperatures of operation. The current industry standard method of applying TBCs for turbine blades in jet engines is electron-beam physical vapor deposition (EB-PVD), which results in a columnar structure that is valued for its high degree of strain tolerance. An emerging deposition method is plasma-spray physical vapor deposition (PS-PVD), capable of producing a variety of customizable microstructures as well as non-line-of-sight deposition, which allows more complex geometries to be coated, or even multiple parts at once. The pseudo-columnar …

Fabrication And Characterization Of Nonlinear Optical Ceramics For Random Quasi-Phase-Matching, Xuan Chen

Electronic Theses and Dissertations

A number of technologies rely on the conversion of short laser pulses from one spectral domain to another. Efficient frequency conversion is currently obtained in ordered nonlinear optical materials and requires a periodic spatial modulation of their nonlinear coefficient which results in a narrow bandwidth. One can trade off efficiency for more spectral bandwidth by relaxing the strict phase-matching conditions and achieve nonlinear interaction in carefully engineered disordered crystalline aggregates, in a so-called random quasi-phase-matching (rQPM) process. In this dissertation, we examine appropriate fabrication pathways for (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT) and ZnSe transparent ceramics for applications in the mid-IR. The main challenge …

Ice Adhesion Analysis Of Severely Aged Pdms Rubbers, Theodore R. Woll

Electronic Theses and Dissertations

The goal of this study was to evaluate and optimize the ice adhesion test initially developed by the University of Denver and to examine Polydimethylsiloxane (PDMS) based silicone rubbers for their ice-phobicity as a function of their physical and chemistry properties, and under severe oxidative aging. The test is based on an ice block bonded to a silicone rubber substrate and subjected to shear. In its original state, the test had severe limitations that caused the ice to be dislodged through a mixture of shear and peeling. Several steps were taken in this research to improve the test, and the …

Modeling And Validations Of Control Parameters For Material Extrusion-Based Additive Manufacturing Of Thixotropic Aluminum Alloys., Lars Herhold

Electronic Theses and Dissertations

Additive Manufacturing (AM) with metals has been accomplished mainly through powder bed fusion processes. Initial experiments and simulations using Material Extrusion Additive Manufacturing (MEAM) have been performed by various researchers especially using low melting alloys. Recently Stratasys Inc. submitted a patent application for the use of their Material Extrusion technology also called Fused Deposition Modeling (FDM) where they describe the process using thixotropic semi-solid alloys. Currently this process using semi-solid, engineering type alloys such as A356 or THIXALLOY 540 aluminum have not been researched to evaluate the control parameters. This research combines the in-depth knowledge of applying thixotropic semi-solid aluminum …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Optimization Of Microfluidic Particle Separator Geometry Using Computational Fluid Dynamics, Joseph Petersen

Electronic Theses and Dissertations

Computational fluid dynamics software was used to simulate the motion of circulating tumor cells in a variety of microfluidic cell isolation devices. Design of several novel microfluidic cell isolation devices was aided by viewing streamlines of fluid in devices in simulation. Devices that performed best in simulation used 5-micrometer wide guiding channels to guide cells to the capture location in the device. While these devices performed better than other devices in simulation and captured all particles regardless of position along inlet, experimental results differ from simulation.

Simulation Of Gas Dynamic Cold Spray Process, Sai Rajkumar Vadla

Electronic Theses and Dissertations

The utilization of computational fluid dynamics (CFD) as a study tool in the aerodynamics and turbomachinery industry reinforces efficiency in the design of aircraft or for understanding the flow through pipes. CFD offer tools to model different geometries and perform a more extensive study of the flow phenomena. This gives the opportunity to model a variety of geometries and analyze their behavior under different operating conditions. A similar approach can be applied to coating technologies. Coating technologies play an essential role in the manufacturing industry. Their ability to form layers of specific materials onto engineering components to enhance mechanical and …

Additive Manufacturing With High Density Polyethylene: Mechanical Properties Evaluation, Calvin Wampol

Electronic Theses and Dissertations

High-density polyethylene is a common recyclable plastic that has a large potential as an additive manufacturing material due its economic and environmental benefits. However, high-density polyethylene has undesirable thermal properties that cause the material to shirk and not adhere to the printing bed during an additive manufacturing processes. Researchers have attempted to combat these thermal properties but have only created novel filaments of high-density polyethylene without being able to create 3D printed specimens for mechanical property testing. This paper presents several methods to create 3D printed specimens with pure high-density polyethylene filament on a fused filament fabrication type 3D printer. …

Data Driven Discovery Of Materials Properties., Fadoua Khmaissia

Electronic Theses and Dissertations

The high pace of nowadays industrial evolution is creating an urgent need to design new cost efficient materials that can satisfy both current and future demands. However, with the increase of structural and functional complexity of materials, the ability to rationally design new materials with a precise set of properties has become increasingly challenging. This basic observation has triggered the idea of applying machine learning techniques in the field, which was further encouraged by the launch of the Materials Genome Initiative (MGI) by the US government since 2011. In this work, we present a novel approach to apply machine learning …

The Development Of A Vacuum Forming System For Kydex® And Other Thermoplastic Sheet, Andrew G. Smith

Electronic Theses and Dissertations

Vacuum forming is a popular, cost effective method amongst large and small scale applications. The method is used to mold a material to the surface of a mold/pattern in order to create a negative copy for reproduction or an object in positive form. The prototype vacuum forming system developed and documented herein is of a membrane-seal type that consists of three (3) principle parts: radial platen, Hinged Frame and Platen Support Assembly, and a PVC surge tank. Each part is described in detail through design, manufacturing, and testing processes. The design supports functional versatility, small scale molding, and uses readily …

Polyelectrolyte And Hydrogel Stabilized Liquid Crystal Droplets For The Detection Of Bile Acids, Jinan Deng

Electronic Theses and Dissertations

Liquid crystal (LC) droplets show great potential as an optical probe for sensor applications due to their large surface areas and stimuli-response director configurations. Bile acids with amphipathic properties, which are formed in liver and secreted into the small intestine, play an important role in the digestion of fats and fat-soluble vitamins. After the digestion process, most of bile acids are recycled back to the liver and ready for the next digestion. Only a few of them are excreted into body fluids. However, there is significant increases in the concentration level of bile acids in body fluids for patients with …

The Study Of Physiochemical Properties Of Cerium Oxide Nanoparticles And Its Application In Biosensors, Swetha Barkam

Electronic Theses and Dissertations

Biosensors continue to get smaller and faster with the advancement in nanotechnology through the use of nanomaterials to achieve high sensitivity and selectivity. However, the continued reliance on biomolecules or enzymes in the biosensor assembly poses the problem of reproducibility, storage and complexity. This dissertation research address some of the challenges by investigating the physiochemical properties of nanoparticles to understand its interaction with biological systems and develop enzyme free biosensors. In this study, we have demonstrated a novel strategy to integrate cerium oxide nanoparticles (CNPs) as an efficient transducer through rigorous screening for developing enzyme/label free biosensors for detecting analytes …

Redox-Active Solid State Materials And Its Biomedical And Biosensing Applications, Ankur Gupta

Electronic Theses and Dissertations

Reactive oxygen species (ROS) are byproducts of physiological processes in human body, and strengthened production of ROS is known to cause acute conditions such as inflammation, aging, Alzheimer's disease, melanoma and ovarian cancer, fibrosis and multiple sclerosis. Therefore, early detection of ROS at nanomolar concentration (at cellular level) and developing more potent antioxidants is essential for regular health monitoring. As an example, ROS are also responsible for inflammation reactions at orthopedic implants-tissue interface triggered by wear debris. Inflammation induced by ROS results in revision surgery. Coatings of redox-active materials exhibiting antioxidant properties on implants have potential to mitigate the inflammation …

Developing An Insider Threat Experimental Environment, Eric Ortiz

Electronic Theses and Dissertations

Simulated, 3D gaming environments have been used for a wide-range of applications including training, entertainment, and experimentation in an assortment of domains for some time. This can be attributed to their unique ability to emulate multifaceted situations that may be difficult to control, while affording participants the opportunity to operate in a relatively safe environment. In cybersecurity research, investigation of insider threat behavior is an endeavor that has received little attention in terms of available environments and resources for experimental manipulation. This research effort aimed to close this gap. A simulated, 3D gaming environment and accompanying scenarios were developed for …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

Advanced Metrology And Diagnostic Loss Analytics For Crystalline Silicon Photovoltaics., Eric Schneller

Electronic Theses and Dissertations

Characterization plays a key role in developing a comprehensive understanding of the structure and performance of photovoltaic devices. High quality characterization methods enable researchers to assess material choices and processing steps, ultimately giving way to improved device performance and reduced manufacturing costs. In this work, several aspects of advanced metrology for crystalline silicon photovoltaic are investigated including in-line applications for manufacturing, off-line applications for research and development, and module/system level applications to evaluate long-term reliability. A frame work was developed to assess the cost and potential value of metrology within a manufacturing line. This framework has been published to an …

Quantification Of The Effect Of Degassing On The Microstructure, Chemistry And Estimated Strength Of Nanocrystalline Aa5083 Powder, Clara Hofmeister

Electronic Theses and Dissertations

Degassing is a critical heat treatment process in aluminum powder metallurgy, where powders are subjected to high temperature in vacuum to remove volatile gaseous species absorbed in and adsorbed on powders. For cryomilled aluminum alloy powders with nanoscale features, degassing can cause accelerated microstructural and chemical changes including removal of volatiles, grain growth, dislocation annihilation, and formation of dispersoids. These changes can significantly alter the mechanical behavior of consolidated components based on their contributions to strength. In this study, cryomilled AA5083 (0.4 wt.% Mn; 4.5 wt.% Mg; minor Si, Fe, Cu, Cr, Zn, Ti; balance Al) powders were degassed at …