Engineering Science and Materials Commons^™

An Understanding Of The Application Of Research Methods In Engineering Management, Andres Sousa-Poza, Rafael Landaeta, Leonardo Bedoya, Ipek Bozkurt, Yaneth Correa

Engineering Management & Systems Engineering Faculty Publications

In this article, the use of research methods in the field of Engineering Management is analyzed. For this study, a database was formed by using articles from three journals in the Engineering Management field: the Engineering Management Journal (EMJ), the IEEE Transactions on Engineering Management and the Journal of Engineering and Technology Management (JETM). Articles written between 1999 and 2003 were analyzed and an Engineering Management research position map was developed to describe holistically the research methods being used in Engineering Management. No judgment on the Engineering Management field per se was undertaken as a result of this study. Instead, …

Evolution Of The Band Structure Of Β-In2 S3−3x O3x Buffer Layer With Its Oxygen Content, N. Barreau, S. Marsillac, J. C. Bernède, L. Assmann

Electrical & Computer Engineering Faculty Publications

The evolution of the band structure of β-In2 S3−3x O3x (BISO) thin films grown by physical vapor deposition, with composition x, is investigated using x-ray photoelectron spectroscopy. It is shown that the energy difference between the valence-band level and the Fermi level remains nearly constant as the optical band gap of the films increases. As a consequence, the difference between the conduction band level and the Fermi level increases as much as the optical band gap of the films. The calculation of the electronic affinity [ ] of the BISO thin films shows that it decreases linearly from 4.65 …

Fuzzy System Identification Based Upon A Novel Approach To Nonlinear Optimization, Raymond Scott Starsman

Electrical & Computer Engineering Theses & Dissertations

Fuzzy systems are often used to model the behavior of nonlinear dynamical systems in process control industries because the model is linguistic in nature, uses a natural-language rule set, and because they can be included in control laws that meet the design goals. However, because the rigorous study of fuzzy logic is relatively recent, there is a shortage of well-defined and understood mechanisms for the design of a fuzzy system. One of the greatest challenges in fuzzy modeling is to determine a suitable structure, parameters, and rules that minimize an appropriately chosen error between the fuzzy system, a mathematical model, …

Developing A Methodology To Detect Partial Failures For Dynamic Systems, Anwar A. Al-Jowder

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this research is to develop a decision support system that can assist in detecting partial failures in dynamic systems such as Fire Control System Tracking Radar (TR) onboard Naval Ships. Partial failures do not necessarily shut down the system immediately but cause degradation of operational performance. Previous work has shown that experts in the field of failure detection, test point insertion and Built-In-Test Equipment (BITE) can provide useful input in detecting partial failures. Partial failures affect operational system performance and support costs, which can be significant. Often, however, partial failure detection consists of the estimations and opinions …

Study Of A Growth Instability Of Γ-In[Sub 2]Se[Sub 3], C. Amory, J. C. Bernede, S. Marsillac

Electrical & Computer Engineering Faculty Publications

γ-In[sub 2]Se[sub 3] thin film are deposited for various substrate temperatures in the range of 523–673 K. This study shows that at 573 and 673 K the thin films are well crystallized with grains aligned along the c axis. Between these temperatures, a domain of instability appears where the γ-In[sub 2]Se[sub 3] thin films have a randomly orientation and the c-lattice parameter increases. The presence of the metastable phase κ-In[sub 2]Se[sub 3], during the growth, can explain the existence of this domain of instability. The insertion of Zn during the preparation process allows us to stabilize the phase κ at …

On Multifunctional Collaborative Methods In Engineering Science, Jonathan B. Ransom Sr.

Mechanical & Aerospace Engineering Theses & Dissertations

Engineers are challenged to produce better designs in less time and for less cost. Hence, to investigate novel and revolutionary design concepts, accurate, high-fidelity data must be assimilated rapidly into the design, analysis and simulation process. This data assimilation should consider diverse mathematical modeling and multi-discipline interactions necessitated by concepts exploiting advanced materials and structures. Integrated high-fidelity methods with diverse engineering applications provide the enabling technologies to assimilate these high-fidelity, multi-disciplinary data rapidly at an early stage in the design. These integrated methods must be multifunctional, collaborative and applicable to the general field of engineering science and mechanics.

Multifunctional methodologies …

A Comparison Of Quasi-Static Indentation Testing To Low Velocity Impact Testing, Michael J. Douglas

Mechanical & Aerospace Engineering Theses & Dissertations

A static test method for modeling low-velocity foreign object impact events to composites would prove to be very beneficial to researchers since much more data can be obtained from a static test than from an impact test. In order to examine if this is feasible, a series of static indentation and low velocity impact tests were carried out and compared. Square specimens of many sizes and thicknesses were utilized to cover the array of types of low velocity impact events. Laminates with a rt/4 stacking sequence were employed since this is by far the most common type of engineering laminate. …

Textured Mos 2 Thin Films Obtained On Tungsten: Electrical Properties Of The W/Mos 2 Contact, E. Gourmelon, J. C. Bernède, J. Pouzet, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Textured films of molybdenum disulfide have been obtained by solid state reaction between the constituents in thin films form when a (200) oriented tungsten sheet is used as substrate. The crystallites have their c axis perpendicular to the plane of the substrate. The annealing conditions are T=1073K and t=30 min. The films are stoichoimetric and p type. Such highly textured films are achieved without foreign atom addition (Ni, Co...). It appears, as shown by x-ray photoelectron spectroscopy, that a thin WS₂ layer is present at the interface W/MoS₂. The crystallization process is discussed by a …

Large Amplitude Pitching Of Supermaneuver Delta Wings Including Flow Control, Yahia A. Abdelhamid

Mechanical & Aerospace Engineering Theses & Dissertations

The unsteady, three-dimensional Navier-Stokes equations are solved to simulate and study the aerodynamic response of a delta wing undergoing large amplitude pitching motion up to 90° angle of attack. The primary model under consideration consists of a 76° swept, sharp-edged delta wing of zero thickness, initially at zero angle of attack. The freestream Mach number and Reynolds number are 0.3 and 0.45 × 106, respectively. The governing equations are solved time-accurately using the implicit, upwind, Roe flux-difference splitting, finite-volume scheme. Both laminar and turbulent flow solutions are investigated. In the laminar flow solutions, validation of the computational results is carried …

Effect Of Temperature On Short-Term Creep Rupture Response In Polymer Matrix Pultruded Composites, Robert Harold Munson

Mechanical & Aerospace Engineering Theses & Dissertations

Polymer matrix pultruded composites have increasingly been used in applications where high strength-to-weight ratio and corrosion resistance are needed. Bridge and pier components are a couple of recent applications due the composite's resistance to corrosion from salt water. In applications of this sort, the material will commonly be subjected to sizable static loads while exposed to varying weather conditions. In using pultruded composites for these applications safely, a better understanding of the material's response to ambient conditions is necessary.

In this thesis, rectangular specimens of a polyester matrix glass reinforced pultruded composite sheet are subjected to both static tensile loading …

Newton Parameter Update Algorithm For Recurrent Neural Networks Applied To Adaptive System Identification And Control, Donald Allen Gates

Electrical & Computer Engineering Theses & Dissertations

This paper shows that the combination of a second-order neural network parameter update algorithm and internal network feedback can be effectively used for adaptive, nonlinear, dynamical system identification and control. Adaptive neural identification and control algorithms are typically utilized for real-time applications where the rate of adaptation is often critical. A fast, adaptive network parameter update algorithm is presented.

Simulation results show that this algorithm is capable of quickly identifying and adapting to changes in system parameters, making it feasible to use for real-time control and fault accommodation applications.

An Experimental Investigation Into The Effect Of Clearance And Torque On Load Sharing In A Bolted Joint, Jerry B. Robertson

Mechanical & Aerospace Engineering Theses & Dissertations

The shear load experienced by each bolt in a multi-fastener bolted butt joint is a percentage of the total load applied to the joint. Joint failure can be premature when one fastener is subjected to a disproportional amount of the total load. Conversely, the ultimate load the joint can endure may be increased if the distribution of loads can be equalized by some means. In this investigation, two and four fastener butt joints were studied. An instrumented bolt was constructed that could measure the bending stresses in the bolt associated with the bearing load. That data was converted into force …

Efficient Dynamic Unstructured Methods And Applications For Transonic Flows And Hypersonic Stage Separation, Xiaobing Luo

Mechanical & Aerospace Engineering Theses & Dissertations

Relative-moving boundary problems have a wide variety of applications. They appear in staging during a launch process, store separation from a military aircraft, rotor-stator interaction in turbomachinery, and dynamic aeroelasticity.

The dynamic unstructured technology (DUT) is potentially a strong approach to simulate unsteady flows around relative-moving bodies, by solving time-dependent governing equations. The dual-time stepping scheme is implemented to improve its efficiency while not compromising the accuracy of solutions. The validation of the implicit scheme is performed on a pitching NACA0012 airfoil and a rectangular wing with low reduced frequencies in transonic flows. All the matured accelerating techniques, including the …

Design Optimization Of Magnetic Bearings And Magnetic Suspension Systems, V. Dale Bloodgood Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic suspension systems were first demonstrated as practical by Holmes and Beams in the 1930's. Since then, numerous academic researchers have worked with various types of these systems. Commercial applications have largely been limited to magnetic bearings for rotating machinery. Other applications that have held considerable promise include wind tunnel model suspensions, space payload pointing and vibration isolation systems, satellite momentum storage and control devices and electromagnetic launch systems. However, none of these have progressed significantly beyond the prototype stage. Maglev trains have not reached serious commercial service but are being aggressively developed in Germany and Japan.

Design methods for …

Ir-Hot Gas Heat Source For Automated Tow Placement, Ray Walton Grenoble

Mechanical & Aerospace Engineering Theses & Dissertations

A series of five experiments on the NASA Langley automated tow placement robot revealed stagnation of gas flow in the nip region. Since the torches could not heat effectively in the nip region, the roller temperature was the dominant influence on interlaminar bond strength. The roller temperatures required for high bond strength caused resin and fiber on the panel top surface to adhere to the compaction roller. Resin and fiber was pulled from the panel surface and wrapped around the roller, which was a severe processing problem. A supplemental radiant heat source was designed to permit reductions in roller temperature. …

Placement Of Piezoelectric Actuators For Active Control Of Vibration Using Modal Parameters, Xuegeng Zhu

Mechanical & Aerospace Engineering Theses & Dissertations

An equation is derived to model the piezoelectric actuators incorporation with flexible structures. This equation permits the comparison of the performance indices over the entire structure for a piezoelectric actuator with constant area, which is unachievable if the Finite Element Method is used for complicated structures.

An index has been developed for placement of piezoelectric actuator for control of vibration of a flexible structure. This index is derived from the definition of H2norm. Computation of the proposed index requires only the natural frequencies and corresponding mode shapes of the structures of interest. The method is well suited to large …

Thermal And Mechanical Behavior Of Cryogenic Propellant Tank Concepts For Advanced Launch Vehicles, H. Kevin Rivers

Mechanical & Aerospace Engineering Theses & Dissertations

An important step in developing a cost-effective, fully-reusable, launch vehicle is the development of durable, lightweight, insulated, cryogenic propellant tanks. Current cryogenic tanks are expendable, and much of the technology that exist is not usable on future vehicles. As part of the Reusable Launch Vehicle/ X-33 Program, an experimental apparatus for evaluating the effects of both thermal and mechanical loading on cryogenic-tank concepts was developed at the NASA Langley Research Center. Studies to determine the behavior of various liquid-oxygen- and liquid-hydrogen-tank concepts under simulated mission conditions were performed as part of this research and are reported. Selected analytical studies of …

Research Related To Multi Degree Of Freedom Magnetic Suspensions, Yan Yang

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis covers the activities associated with 1) recommissioning of the 6-inch Magnetic Suspension and Balance System (MSBS) and 2) enhancing the Annular Suspension and Pointing System (ASPS). These activities continue the program of research in the multi degree of freedom magnetic suspension program at Old Dominion University. The 6-inch MSBS is a large gap magnetic suspension system used as a model support and balance system in wind tunnels. The first stage of recommissioning of the 6- inch MSBS for the 6-inch subsonic wind tunnel is performed. Experimental data and computational results for the magnetic field distribution of the MSBS …

Correlation Of Finite Element Prediction And Experimental Measurements Of Aircraft Panel Structural Vibration, Olaf L. Storaasli

Mechanical & Aerospace Engineering Theses & Dissertations

With the rapid development of computational capabilities and the implementation of complex tools for commercial finite element programs, predicting structural dynamics and related acoustics of complex structures is presently achievable. Structural finite element modeling is a design tool widely utilized for analysis of problems of all kinds. However, high frequency vibration of complex structures, such as the reinforced aircraft panel used for this study, currently does not correlate well with experimental measurements using conventional modeling methods. An investigation into the commonly used modeling techniques as well as the new tools of commercial finite element analysis packages for the prediction of …

An Experimental Investigation Of Bolt Preload Relaxation In Pultruded Gfrp Composite Joints, Srinivas Ravi

Mechanical & Aerospace Engineering Theses & Dissertations

Mechanically fastened joints in pultruded composites are necessary for reasons of maintenance, repair, and assembly. Pultruded composites utilize polymers as matrices and therefore are susceptible to time-dependent effects. The positive effects of increasing the clamping force in bolted joints are well known. To maintain a safe operation of the assembly a minimum clamping force must be guaranteed. But since these materials show time-dependent effects, the bolt-preload relaxes over a period of time. The present study is aimed at investigating the bolt preload relaxation. In this study 1/2 in. thick pultruded sheets were first tested under compression in the thickness direction. …

Development Of Curved-Plate Elements For The Exact Buckling Analysis Of Composite Plate Assemblies Including Transverse-Shear Effects, David Michael Mcgowan

Mechanical & Aerospace Engineering Theses & Dissertations

The analytical formulation of curved-plate non-linear equilibrium equations including transverse-shear-deformation effects is presented. The formulation uses the principle of virtual work. A unified set of non-linear strains that contains terms from both physical and tensorial strain measures is used. Linearized, perturbed equilibrium equations (stability equations) that describe the response of the plate just after buckling occurs are then derived after the application of several simplifying assumptions. These equations are then modified to allow the reference surface of the plate to be located at a distance z_c, from the centroidal surface. The implementation of the new theory into the …

Broadband Dynamic Modification Using Feedforward Control, Kendeas Antonis Karantonis

Mechanical & Aerospace Engineering Theses & Dissertations

The use of feedforward control for dynamic modification is relatively new to the area of structural vibration control. In this thesis the disturbance path dynamics of a flexible aluminum beam, pinned at both ends and under the influence of broadband excitation inputs, are modified through the use of feedforward control. The ideal algebraically determined feedforward control method for response cancellation is first presented. Theoretically, this compensator modifies the disturbance path dynamics to any desired behavior. This ideal algebraic approach can only be used for minimum phase systems. In non-minimum phase systems, right half s-plane plant zeros emerge as unstable poles …

Analysis And Testing Of Plates With Piezoelectric Sensors And Actuators, Jeffrey S. Bevan

Mechanical & Aerospace Engineering Theses & Dissertations

Piezoelectric material inherently possesses coupling between electrostatics and structural dynamics. Utilizing linear piezoelectric theory results in an intrinsically coupled pair of piezoelectric constitutive equations. One set describes the direct piezoelectric effect, where strains produce an electric field, and the other set describes the converse effect, where an applied electrical field produces strain. The purpose of this study is to compare the finite element analysis and experiments of a thin plate with bonded piezoelectric material.

Since an isotropic plate in combination with a thin piezoelectric layer constitutes a laminated composite, the classical laminate plate theory is used in the formulation to …

Dynamics And Control Of A Three Dimensional Gantry Crane With Cable Flexibility, Uchendu H. Eke

Mechanical & Aerospace Engineering Theses & Dissertations

The control of payload swing in industrial gantry cranes is a topic of widespread interest. In this thesis, the control of the swing of a payload idealized by a point mass assumption is investigated utilizing s, compact robotics matrix/vector representation of the dynamical model. In this form, this particular system can be viewed as sn underactuated manipulator with equal numbers of active and passive degrees of freedom. The full three dimensional model is developed and linearized by modelling the cable as a single thread of fiexible wire and the degree of dynamic coupling between the active and passive coordinates is …

Development And Experimental Verification Of A Finite Element Model For Ptc Panel Thermal Analysis, Hamid Sayar

Mechanical & Aerospace Engineering Theses & Dissertations

The Pyramidal Truss Core (PTC) panel is a new structural concept being used in applications requiring a high strength to weight ratio. This study is concerned with investigating the thermal characteristics of the PTC panels. In this regard, the focus of the analysis was to develop an accurate finite element model of PTC panels for thermal analysis. The resulting model included radiation mode of heat transfer as the dominant means of the heat transfer while neglecting the influence of heat transfer through natural convection. The accuracy of the developed model was verified by comparison of the finite element results with …

Progressive Failure Analysis Methodology For Laminated Composite Structures, David Wayne Sleight

Mechanical & Aerospace Engineering Theses & Dissertations

A progressive failure analysis model has been developed for predicting the nonlinear response and failure of laminated composite structures. The progressive failure analysis uses C¹ plate and shell elements based on classical lamination theory to calculate the in-plane stresses. Several failure criteria, including the maximum strain criterion, Hashin's criterion, and Christensen's criterion, are used to predict the failure mechanisms and several options are available to degrade the material properties after failures. The progressive failure analysis model is implemented in COMET and can predict the damage and response of a laminated composite structures from initial loading to final failure.

Effects Of Elevated Temperature On The Physical Aging Of A High Temperature Thermoplastic Resin And Composite, Mark Feldman

Mechanical & Aerospace Engineering Theses & Dissertations

Development of a High Speed Civil Transport is considered by the commercial aviation industry to be one of the next big challenges for our national aircraft industry. Critical to the success of this aircraft is the development of advanced polymeric composites for both the primary and secondary structures and the predictive methodology necessary for assessment of long term durability. While polymeric composites offer an excellent strength to weight ratio a key disadvantage is the time dependent properties exhibited by the polymer matrix which can age and ultimately effect the resultant stiffness of a laminate.

Experimental studies were performed to determine …

An Approach For Multidisciplinary Design Optimization, Robert V. Krueger

Mechanical & Aerospace Engineering Theses & Dissertations

Multidisciplinary Design Optimization (MDO) is an optimization technique that allows complex designs to be improved by managing conflicting goals in such a fashion so as to improve the overall design. This thesis presents a nonhierarchic MDO formulation and gives a general explanation of how it is to be applied to various appropriate problems. In addition, this thesis evaluates the viability of this MDO technique by applying it to two distinct, multidisciplinary problems that have been used as examples in other literature. The first example problem is a combined aerodynamic/structural problem and the second example is an alkylation process problem. First, …

Finite Element Formulation Of A Three-Node Spatially Curved And Twisted Beam, Umesh Vishnu Padhye

Mechanical & Aerospace Engineering Theses & Dissertations

A three-node curved and twisted beam element is developed for linear analysis of structures modeled with curved and pre-twisted beams. A set of governing equations consisting of kinematic relations, constitutive relations, and equilibrium equations is derived. The beam element has three rotational and three displacement degrees of freedom at each node. The differential equations of kinematics are solved exactly for linearly varying longitudinal strains, constant transverse shear strains, linearly varying twist, and quadratically varying curvature changes to obtain the description of rotation and displacement modes. These rotation and displacement modes are then used as the basis functions for development of …

Modeling And Simulation Of Load Introduction For Fuselage Crown Panel Testing, Kevin P. Belack

Mechanical & Aerospace Engineering Theses & Dissertations

This paper discusses the mechanism and behavior of load introduction to internally pressurized fuselage crown panels. Emphasis is placed on the finite element modeling of a simulated pressure-box test machine and representative fuselage crown panel. The geometry and mesh requirements for the finite element model are examined through numerical studies which gradually increase in complexity. These numerical studies culminate in the detailed specification of boundary conditions, mesh densities, load introduction mechanisms, element choice and solution process for the simulation of a pressure-box test machine and test panel.

The results obtained using the finite element model are then compared with experimental …