Engineering Science and Materials Commons^™

Synthesis Of Structurally Ordered Platinum-Iron Catalysts With Enhanced Oxygen Reduction Reaction Activity, Ye-Zheng Cai, Ming-Chuan Luo, Fang-Hui Wang, Zhao-Nan Sun, Hong Zhu

Journal of Electrochemistry

To improve oxygen reduction reaction catalytic activity of the precious metals platinum for fuel cell, the precursors of carbon-supported structurally disordered platinum-iron alloy (D-Pt₃Fe/C and D-PtFe/C) catalysts with different compositions were synthesized via a modified polyol reduction method. Then, by optimizing the annealing conditions in the inert gas, we turned the structurally disordered platinum-iron alloy to the structurally ordered platinum-iron alloy (O-Pt₃Fe/C and O-PtFe/C) catalysts. The structural characterizations of the as-prepared catalysts were performed by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The results …

Rambling Between "Zhong Yong" And "Catalysis", Zi-Dong Wei

Journal of Electrochemistry

“Zhong Yong” represents a traditional Chinese wisdom, which was first proposed by Confucius and continuously richened by his followers. “Zhong Yong” pursues the balances among all kinds of contradictions, and insists that neither “too much” nor “not enough” is good. For a successful catalyst, on which the adsorption of reactants must be not so strong and not so weak either. On this point of view, there are the same pursuits for “Zhong Yong” and catalysis. In this paper, the author starts his story with a conversation between Confucius and his student, followed by 3 interesting stories happening in the ancient …

Nitrogen, Fluorine Co-Doped Silk-Derived Carbon For Electrochemical Oxygen Reduction With High Performance In Alkaline Solution, Fang-Fang Liu, Hong-Liang Peng, Shi-Jun Liao

Journal of Electrochemistry

A high-performance, doped carbon-based catalyst was synthesized by pyrolyzing hydrothermally treated silkworm cocoon. The effects of preparation conditions and fluorine promotion on various catalysts’ performance were investigated. The catalyst prepared under optimal conditions and doped with nitrogen and fluorine possessed the high specific surface area of more than 1000 m^2⋅g^-1 and contained 3.5 and 7.3% (by mass, the same below) N and F, respectively. The activity of the catalyst toward oxygen reduction reaction in an alkaline medium was comparable to that of commercial Pt/C, showing both superior tolerance to methanol poisoning and better durability. Doping with fluorine …

Electrochemical H2O2 Sensor Based On The Co-Immobilization Of Phosphmolybdic Acid And Graphene On Pedot Film Electrode With Nafion, Hao-Xian Zhou, Jun-Ming Zhang, Zhi-Yu Qu, Pan-Yu Zhang, You-Jun Fan

Journal of Electrochemistry

With a glassy carbon electrode (GCE) as the substrate, the poly(3,4-ethylenedioxythiophene) (PEDOT) film electrode was prepared through the electrochemical polymerization method, then a novel non-enzymatic electrochemical H₂O₂ sensor was fabricated by co-immobilizing phosphomolybdic acid and graphene with Nafion on the PEDOT/GCE electrode. The modified electrodes were characterized by scanning electron microscopy (SEM), while the responsive properties of the sensor to H₂O₂ were investigated by cyclic voltammetry and chronoamperometry. The results demonstrated that, under the optimized conditions, the sensor exhibited good electrocatalytic performance for H₂O₂ reduction. The current response of the sensor …

Electrochemical Detection Of Hydrogen Peroxide At Aunps Modified Electrode Using P-Hydroxyphenylboronic Acid As A Precursor, Chun-Yan Wang, Xiao-Qiu Liu, Ying-Xin Qi

Journal of Electrochemistry

We developed a new method for electrochemical detection of hydrogen peroxide (H₂O₂) based on boronate oxidation of p-hydroxyphenylboronic acid. This method using p-aminophenol which is produced from the reaction of H₂O₂ and p-aminophenylboronic acid as a well electrochemical probe, combined with a gold nanoparticles (AuNPs) modified electrode for an indirect detection of H₂O₂. Because of the large surface area and enhanced electrocatalytic behavior by the AuNPs modified electrode, the detection sensitivity was improved. The method could detect H₂O₂ in the concentration range of 1 ~ 100 …

Electrochemical Determination Of Hg(Ii) At Gold Nanoparticles@Carbonaceous Microspheres Modified Electrode, Tian-Yu Qiu, Ming-Chun Wang, Xian-Feng Du, Tian-Jia Jiang, Xing-Jiu Huang

Journal of Electrochemistry

The gold nanoparticles@carbonaceous microspheres (Au@CMSs) and  Au@CMSs modified glassy carbon electrode (GCE) were prepared. The Au@CMSs modified  GCE was further examined for possible sensitive detection of mercury ions (Hg(II)) in an aqueous solution by square wave anodic stripping voltammetry (SWASV). The excellent performance was found in the stripping analysis of Hg(II) in 0.1 mol•L^-1 NaAc-HAc(pH=5.0) with a sensitivity of 25.863 A•(mol•L^-1)^-1 and a detection limit of 3.69×10^-8 mol•L^-1 based on the 3σ method.

Fabrication Of Riboflavin Electrochemical Sensor Based On Au Nanoparticles/Polydopamine/Carbon Nanotubes Modified Glassy Carbon Electrode, Hua-Ping Peng, Mei-Ling Yu, Xin Liu, Pan Liu, Wei Chen, Ai-Lin Liu, Xin-Hua Lin

Journal of Electrochemistry

A novel electrochemical platform for the high sensitivity detection of riboflavin was constructed by Au nanoparticles/polydopamine/carbon nanotubes (Au-PDA-MWCNTs) nanocomposite modified glassy carbon electrode. The Au-PDA-MWCNTs nanocomposite was synthesized by in situ reduction method. The characteristics of the as-prepared Au-PDA-MWCNTs nanocomposite modified electrodes were investigated by using UV-Vis spectroscopy, scanning electron microscopy (SEM) and electrochemical methods. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to study the electrochemical behavior of riboflavin (RF) at Au-PDA-MWCNTs nanocomposite modified electrodes. The results demonstrated that the present electrochemical sensor exhibited a wide linear range from 5×10^-9 mol•L^-1to 1×10^-5 mol•L …

Synthesis Of Fe, N-Doped Graphene/Carbon Black Composite With High Catalytic Activity For Oxygen Reduction Reaction, Chi Chen, Zhi-You Zhou, Xin-Sheng Zhang, Shi-Gang Sun

Journal of Electrochemistry

Oxygen reduction reaction (ORR) is a bottleneck for improving the efficiency of proton-exchange membrane fuel cells as a cathode reaction due to its sluggish kinetics. The exploitation of low cost and high performance non-precious metal catalysts such as Fe/N/C based materials toward ORR has attracted extensive attentions. In this work, the Fe, N-doped graphene nanosheets/carbon black composite was prepared by hydrothermal polymerization and followed by a twice-heat-treatment procedure using 2-aminoimidazole as an N precursor, FeCl₃ as an Fe precursor and KJ600 carbon black as a support. The TEM images revealed that the graphene nanosheets were separated by carbon black …

Electrochemical Syntheses Of Graphene And Its Composites, Bo Zhao, Li Jiang, Ming-Hui Yuen, Xian-Zhu Fu, Rong Sun, Ching-Ping Wong

Journal of Electrochemistry

Graphene is a kind of ideal two-dimensional flat carbon nanomaterials which have unique chemical and physical properties. The attractive potential applications must be based on the high quality mass production of graphene. However, it remains a huge challenge. An electrochemical approach is a fast, environmental friendly and easy-operating method. single- or multi-layered graphene flakes can easily be produced in short periods of time. In this review, the structure, properties and preparation methods of graphene are first introduced. Accordingly, the electrochemical approaches used for the productions of graphene flakes, graphene/inorganic nanocomposites, graphene/polymer composites and graphene analogues are highlighted. Finally, challenges and …

Effect Of Flame Retardant On Electrochemical Performances Of Lithium Ion Battery With Lini0.4Co0.2Mn0.4O2 As A Positive Electrode Material, Yan-Zhuo Lv, Yong-Xian Ge, Zhen-Bo Wang, Ke Ke

Journal of Electrochemistry

The effect of flame retardant on the electrochemical performances of lithium ion battery by using LiNi_0.4Co_0.2Mn_0.4O₂ as a positive material was studied by measuring the first charge-discharge, cycling, circulation, and AC impedance curves. The experimental data indicated that the discharge capacity of the battery decreased, while the charge transfer resistance and the lithium ion diffusion resistance increased with the increases in the concentrations of the flame retardant in the electrolyte solutions. Furthermore, the stability of the battery at small discharge ratios and the cyclic performance were also improved by the addition of flame …

Electricity Generation Of Microbial Fuel Cell Using Stainless Steel Mesh As Cathode, Hong-Yan Dai, Hui-Min Yang, Xian Liu, Xuan Jian, Xiu-Li Song, Zhen-Hai Liang

Journal of Electrochemistry

In the present work, a dual-chamber microbial fuel cell (MFC) was constructed with aeration tank sludge as an inoculum, carbon felt as an anode and stainless steel mesh without any modification as a cathode. The influence of the cathode size was investigated in terms of voltage output, power generation and electrochemical impedance. The long-term durability of the stainless steel mesh cathode was also evaluated. Results showed that the stainless steel mesh exhibited satisfactory long-term durability as MFC cathode. When the stainless steel mesh size was 2 × 2 cm², the maximum output voltage, power density, the internal resistance …

The Study On Comparison Of Electrochemical Performance In Microbial Fuel Cell With Glucose And Sodium Acetate Acting As Substrates, Lei Fan, Yu Zhao, Ting Li, Qin-Bo Yuan, En-Zhi Wang, Xiao-Bin Wang, Jun-Wen Wang

Journal of Electrochemistry

By inoculating aerobic sludge and anaerobic sludge from the sewage treatment plant, two sets of dual-chamber microbial fuel cells (MFCs) were built with either glucose or sodium acetate acting as a substrate. Accordingly, the electrochemical performances of MFCs were explored with the concentration of the substrates being 0.0335 mol⋅L^-1. The results of the comparative study in glucose system and sodium acetate system showed that the impedance values of anodic half cell were 222 Ω for glucose and 213.67 Ω for sodium acetate, implying no significant effect on the internal resistance in battery with the different substrates. The exchange …

Thermoelastic Waves In Microstructured Solids, Arkadi Berezovski, Mihhail Berezovski

Publications

Thermoelastic wave propagation suggests a coupling between elastic deformation and heat conduction in a body. Microstructure of the body influences the both processes. Since energy is conserved in elastic deformation and heat conduction is always dissipative, the generalization of classical elasticity theory and classical heat conduction is performed differently. It is shown in the paper that a hyperbolic evolution equation for microtemperature can be obtained in the framework of the dual internal variables approach keeping the parabolic equation for the macrotemperature. The microtemperature is considered as a macrotemperature fluctuation. Numerical simulations demonstrate the formation and propagation of thermoelastic waves in …

Case Studies Of Cavity And External Wall Insulation Retrofitted Under The Irish Home Energy Saving Scheme: Technical Analysis And Occupant Perspectives, Aimee Byrne, Gerard Byrne, Garrett O'Donnell, Anthony Robinson

Articles

The residential sector represents 27% of primary energy consumption in Ireland. This paper examines the case study of the Irish government’s national grant scheme to encourage energy efficiency retrofit in private housing. That is the Home Energy Saving (HES) Scheme, later rebranded the Better Energy: Homes (BEH) Scheme. The methodology involved monitoring several homes immediately before and after retrofit alongside discussions with occupants. The examination focused on specific measures commonly introduced through the HES/BEH programme − cavity and external wall insulation. It has been found that a significant decrease in heat loss through the walls was measured in all cases. …

Fabrication And Testing Of Cfrp Composites With Embedded Piezoelectric Particles For Temperature Sensing And Energy Harvesting, Emilio Tarango Valles

Open Access Theses & Dissertations

As a part of this world's continuous evolution and technological advancements, smart materials and functional composites have become an attractive topic. In many cases, these new functional composites are replacing the traditional engineering material due to their customizable mechanical properties. This Thesis analyzes and demonstrates the signal response, sensing capabilities and structural properties from Carbon/Glass Fiber Reinforced Plastic Composites (CFRP) with embedded Lead Zirconate Titanate Particles (PZT). The added PZT particles function as actuators, giving the composites a functionality. The PZT quantity inside each composite was variated to study better and characterize the mechanical and electrical properties; the variations were …

Quantitative Assessment Of Secondary Flows Of Single-Phase Fluid Through Pipe Bends, Z. Kaldy, O. Ayala

Engineering Technology Faculty Publications

Single-phase fluid flow was simulated passing through various three dimensional pipe elbows. The simulations varied by Reynolds number, curvature ratios, and sweep angles and were all conducted using the k-e model available in COMSOL Multiphysics 5.1. The intent of this research was to qualitatively assess the flow characteristics under several different conditions. Many similarities were seen especially when comparing curvature ratios, the vorticity location for the turbulent cases show near identical behavior at the elbow midsection. One of the variables quantified in this paper is the maximum secondary velocity module which shows increasing values until the midsection of the elbow.

Improving The Engineering Properties Of Pla For 3d Printing And Beyond, Carmen R. Rocha

Open Access Theses & Dissertations

Additive manufacturing (AM), now more commonly known as 3D printing, has been classified as efficient, fast, and practical in the prototyping sector of product development. In the work presented here, we will use one of the AM techniques known as Material extrusion 3D printing (ME3DP), which has all the advantages of AM. However, one of the biggest challenges facing ME3DP technologies is the limitation of the range of materials used by this technique. Acrylonitrile butadiene styrene (ABS) and poly-lactic acid (PLA) are currently the most common thermoplastics materials used in ME3DP because of their ability to melt and be reprocessed. …

Methodology For Analyzing Epoxy-Cnt Phononic Crystals For Wave Attenuation And Guiding, Madhu Kolati

Dissertations, Master's Theses and Master's Reports

Phononic crystals (PhnCs) control, direct and manipulate sound waves to achieve wave guiding and attenuation. This dissertation presents methodology for analyzing nanotube materials based phononic crystals to achieve control over sound, vibration and stress mitigation. Much of the analytical work presented is in identifying frequency band gaps in which sound or vibration cannot propagate through these PhnCs. Wave attenuation and mitigation analysis is demonstrated using finite element simulation. Engineering principles from current research areas of solid mechanics, solid-state physics, elasto-dynamics, mechanical vibrations and acoustics are employed for the methodology. A considerable effort is put to show that these PhnCs can …

Towards The Scalability And Hybrid Parallelization Of A Spatially Variant Lattice Algorithm, Henry Roger Moncada Lopez

Open Access Theses & Dissertations

The purpose of this research is to design a faster implementation of the spatially variant algorithm that improves its performance when it is running on a parallel computer system.

The spatially variant algorithm is used to synthesize a spatially variant lattice for a periodic electromagnetic structure. The algorithm has the ability to spatially vary the unit cell orientation and exploit its directional dependencies. The algorithm produces a lattice that is smooth, continuous and free of defects. The lattice spacing remains strikingly uniform when the unit cell orientation, lattice spacing, fill fraction and more are spatially varied. This is important for …

Secondary Flow Of Liquid-Liquid Two-Phase Fluids In A Pipe Bend, M. Ayala, P. Santos, G. Hamester, O. Ayala

Engineering Technology Faculty Publications

A simulated study of oil and water in 90 degree bend was carried on COMSOL 5.1 to characterize flow pattern and analyze the secondary flow. The Euler-Euler k-e Reynolds Averaged Navier-Stokes model was used to represent the fluid motion. Changes in the Reynolds number, curvature ratio and direction of gravity were made to evaluate the effects in the intensity of the secondary flow. In the end, it was possible to see that the bend direction does not affect the formation of secondary flow for Reynolds above 100,000. It appears that the fluid behavior on the pipe bend is strongly related …

Applications Of Carbon Materials In Electrochemical Energy Storage, Ji Liang, Lei Wen, Hui-Ming Cheng, Feng Li

Journal of Electrochemistry

An electrode material for electrochemical energy storage is one of the key components for high performance devices. In a variety of electrochemical energy storage systems, carbon materials, especially the lately emerged carbon nanomaterials including the carbon nanotube and graphene, have been playing a very important role and brought new vitality to the development and demonstration of the broad application prospects. In this review, we summarize the applications of various carbon materials in the typical electrochemical energy storage devices, namely lithium/sodium ion batteries, supercapacitors, and lithium-sulfur batteries, as well as flexible electrochemical energy storage and electrochemical catalysis. A perspective of novel …

Electrodeposition Of Lanthanum In Deep Eutectic Solvents, Li Wang, You-Jun Fan, Lu Wei, Hai-Xia Liu, Shi-Gang Sun

Journal of Electrochemistry

With the choline chloride/urea deep eutectic solvents (DESs) as the medium, the olive-like lanthanum particles with uniform shape and size were successfully prepared through a potentiostatic deposition method. The prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray (EDX) spectroscopy and X-ray photoelectron spectroscopy (XPS). At the same time, the effect of deposition potential, temperature and time on the size and morphology of samples was investigated. The results demonstrated that the optimum conditions for the preparation of olive-like lanthanum particles were as follows: deposition potential of -1.7 V, temperature of 80 °C and …

Progress Of Self-Supported Supercapacitor Electrode Materials Based On Carbon Substrates, Shui-Jian He, Wei Chen

Journal of Electrochemistry

Self-supported electrode materials have been widely used in supercapacitors. Carbon materials are promising substrates in building self-supported electrode materials attributed to their diverse structures, rich resource, relatively low cost and high stability. Combined with our own research in this field, we summarize here the recent progress on the synthesis of self-supported electrode materials and their supercapacitance properties. The overall synthetic strategy could be divided into two categories: “top-down” and “bottom-up”. We hope this review is helpful for the development and application of renewable sources in self-supported electrode materials.

Synthesis Of Porous Carbon Nanosheets And Its Application In Sodium-Ion Battery, Jing-Fei Zhang, Jing Lu, Xiao-Yu Yang, Yun-Di Huang, Lin Xu, Dong-Mei Sun, Ya-Wen Tang

Journal of Electrochemistry

Owning to sodium’s high abundance, relatively low cost, similar chemical properties to Li and very suitable redox potential of E₀(Na⁺/Na) = -2.71 V versus SHE which is only 0.3 V above that of lithium, rechargeable sodium ion battery hold much promise as potential alternatives to current lithium ion batteries for energy storage applications. Carbon material is regarded as the most promising anode candidate for sodium ion battery. Particularly, carbon nanosheet with porous structure and high conductivity is expected to have improved sodium ion storage properties. In this paper, we present a two-step pyrolysis-based method for facile …

Effect Of Mno2 Content On Electrochemical Capacitance Behavior Of Active Carbon Electrode, Kun Shen, Xian-Liang Zhou, Qi-Shun Duan

Journal of Electrochemistry

In this work, the manganese dioxide (MnO₂) materials were prepared by solution approach at low temperature, thermal decomposition and electrochemical deposition. The actived carbon (AC) and MnO₂composite electrodes were used for aqueous supercapacitors. The morphologies and structures of the prepared materials were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the electrochemical behaviors were tested by cyclic voltammetry (CV) and galanostatic charge-discharge tests. Electrochemical test data show that the maximum specific capacitances of 151, 172 and 141 F•g^-1were obtained with the contents of MnO₂being 70, 60 and 70% in …

Fast And Accurate Evaluation Of Lifepo4 Cathode Materials By Single Particle Microelectrode, Fu-Qing Wang, Yi-Min Wei, Yu-Zhuan Su, Bing-Wei Mao, Kai Wu, Feng-Gang Zhao, Chun-Lei Chen, Xing-Lu Li, Jin Chong

Journal of Electrochemistry

Single particle microelectrode enables to evaluate the electrochemical responses for single particle of active material without binder and conductive agent. Thus, the influences of additive and electrode structure on the electrochemical performance of active materials can be ignored. Furthermore, this technology can be used to evaluate active materials fast. Therefore, single particle microelectrode allows fast and accurate determination of the intrinsic performance of active material. Cyclic voltammogram (CV), cycle performance, and kinetic behavior of LiFePO₄ cathode materials were evaluated by the single particle microelectrode. CV curve of LiFePO₄ particle with a pair of oxidation and reduction peaks was …

Special Issue: Electrochemistry Of Carbon Materials, Wei Chen

Journal of Electrochemistry

Carbon materials are traditional electrode materials due to their excellent electrical conductivities, high electrochemical stabilities and wide potential windows. Glassy carbon, graphite, various activated charcoals, carbon fibers etc. have been widely used in electrochemistry serving as electrode substrates or supports. In addition to their applications in basic electrochemistry, carbon materials have also played important roles in electrochemical energy storage and conversion. In recent years, various types of carbon structures, from zero-dimensional carbon nanodots, one-dimensional nanotubes, two-dimensional graphene to three-dimensional porous carbons, have attracted increasing attention in electrochemical field. It has been found that carbon materials have outstanding properties as advanced …

Colloidal Ionic Supercapacitors, Kun-Feng Chen, Dong-Feng Xue

Journal of Electrochemistry

Supercapacitors have high power density and long cycle life compared with battery systems, but they still suffer from low energy density at the same time. In order to increase the energy density of supercapacitors, we have developed a new type of pseudocapacitor, called colloidal ion supercapacitor, which can directly use commercial metal salts as electrode materials and form electroactive matter by in-situ electrochemical reactions without the need of additional materials synthesis processes. Colloidal ion supercapacitor can fully utilize the redox reaction of metal cations with multiple oxidation states, which can completely release the stored electrical energy of multiple-valence cations, leading …

Carbon Aerogel/Nickel Foam As Electrode For High-Performance Supercapacitor, Zhong Wu, Xin-Bo Zhang

Journal of Electrochemistry

Herein, a facile synthesis has been explored to prepare carbon aerogel/Ni foam. Graphene oxide, resorcinol and formaldehyde serve as precursors and polymerize in-situ on the Ni foam after hydrothermal synthesis at 85 ℃. After lyophilization treatment, the carbon aerogel/Ni foam with porous structure can be obtained. Electrochemical investigations reveal that the carbon aerogel/Ni foam exhibits superior performances in both aqueous and organic electrolytes involving high specific capacitance and long-term cycling stability. The excellent properties can be ascribed to the unique formation and porous structure, which allows more effective transportations of electron and electrolyte ion.

Chemical And Electronic Structure Of Surfaces And Interfaces In Cadmium Telluride Based Photovoltaic Devices, Douglas Arthur Duncan

UNLV Theses, Dissertations, Professional Papers, and Capstones

The surface and interface properties are of the upmost importance in the understanding, optimization, and application for photovoltaic devices. Often the chemical, electronic, and morphological properties of the films are empirically optimized, however when progress slows, a fundamental understanding of these properties can lead to breakthroughs. In this work, surfaces and interfaces of solar cell-relevant films are probed with a repertoire of X-ray analytical and microanalysis techniques including X-ray photoelectron (XPS), X-ray excited Auger electron (XAES), X-ray emission (XES) spectroscopies, and atomic force (AFM) and scanning electron (SEM) microscopies.

Silicon-based devices currently dominate the solar market, which is rather inflexible …