Engineering Science and Materials Commons^™

Investigation Of Ceo2 As Cathode Electrocatalyst For Direct Borohydride Fuel Cell, Xue-Min Ni, Ya-Dong Wang, Mu Pan

Journal of Electrochemistry

The performance of CeO₂ as oxygen reduction electrocatalyst in direct borohydride fuel cell was investigated.The experimental results indicate that CeO₂ shows significant electrocatalytic performance for oxygen reduction and exhibits no observed promotion effect on hydrolysis or electro-oxidation of BH₄^-.The power density of experimental one-compartment fuel cell with CeO₂ as cathode electrocatalyst can reach a 67.8 mW·cm^-2 at room temperature.

Preparation And Electrochemical Behavior Of Li4Ti5O12 Nanosheets As Anode Material For Lithium Ion Battery, Yi-Fei Wang, Yu-Feng Tang, Zheng Qiu, Li Yang

Journal of Electrochemistry

Spinel lithium titanate(Li₄Ti₅O₁₂) nanosheets with a size range of 200 ～400 nm were synthesized by hydrothermal process from the amorphous hydrous titanium oxide precursors.The as-prepared products were characterized by X-ray powder diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The electrochemical behaviors of Li₄Ti₅O₁₂ electrode in conventional organic electrolyte and ionic liquid electrolyte were investigated by using cyclic voltammetry,galvanostatic charge-discharge and AC impedance techniques.The experimental results indicate that the as-prepared nanostructured Li₄Ti₅O₁₂,evaluated as anode material,exhibited good reversibility and cycle performance.It is expected to be a …

Synthesis Of High-Performance Lini1/3Co1/3Mn1/3O2 Cathode Materials Via Azeotropic Distillation Method, Sheng-An Xia, Li-Xia Yuan, Ze Yang, Zhao-Hui Wang, Yun-Hui Huang, Shuang Li, Wu-Xing Zhang, Ya-Bin Meng, Wei-Gong Zheng

Journal of Electrochemistry

Layered LiNi_1/3Co_1/3Mn_1/3O₂ is one of the most promising alternative materials for LiCoO₂ in lithium ion batteries due to its low cost,large capacity and excellent cyclability.In this paper,LiNi_1/3Co_1/3Mn_1/3O₂ was synthesized via azeotropic distillation method with isobutyl alcohol as an azeotropic agent.The structure and surface morphology were characterized by X-ray diffraction(XRD) and scanning electron microscope(SEM),respectively.The as-prepared LiNi_1/3Co_1/3Mn_1/3O₂ shows a layered α-NaFeO₂ structure;the particles are small and uniformly distributed.As compared with the sample prepared by traditional method,the present cathode material …

Electrochemical Behavior Of Co-Ru Composite In Alkaline Solution, Su-Mei Yao, Guo-Chun Li, Xue-Ping Gao

Journal of Electrochemistry

The electrochemical properties of Ru doped cobalt hydroxides synthesized via homogeneous chemical co-precipitation were investigated in 6 mol·L^-1 KOH solution by galvanostatic charge-discharge process and cyclic voltammetry(CV).It is demonstrated that Ru doped cobalt hydroxides exhibited good capacitive characteristic and high specific capacitance.The sample with a Co/Ru molar ratio of 8 /1 shows the optimized electrochemical performance,including capacitive property and discharge capacity.The microstructure and morphology of the obtained Ru doped hydroxides were characterized by X-ray diffraction(XRD) and scanning electron microscope(SEM).The amorphous structure of ruthenium dioxide nanoparticles and single-crystal structure of Co(OH)₂ platelets were confirmed.Based on a structure analysis and …

The Electrochemical Characteristics Of Cpo-Pll/Gc Electrode, Wen Zhao, Xia-Qin Wu, Zhong-Qing Lu, Wen-Jing Hou, He-Xing Li

Journal of Electrochemistry

Poly-L-lysine(PLL) was electropolymerized onto the surface of glassy carbon(GC) electrode.1[(3-dimethylamino)propyl]-3-ethylcarbodiimide hydrochloride(EDC) was used as a Cross-linking agent to immobilized Chloroperoxidase(CPO) onto the PLL/GC electrode.A pair of well-defined redox peaks was observed at CPO-PLL/GC electrode,which clearly suggested that PLL can promote the direct electron transfer between the CPO and the GC electrodes.The cyclic voltammetry results also showed that the electron transfer at CPO-PLL/GC is a surface adsorption-controlled quasi-reversible process,which is accompanied with proton transfer.The CPO-PLL/GC electrode exhibited a good electrochemical stability and excellently electrocatalytic activity for electrochemical reduction of O₂.

Electrochemical Corrosion Behavior Of Tio2/Ha Composite Coating On Medical Titanium In Tyrode's Physiological Solution, Li-Li Kong, Long-Xiang Lin, Rong-Gang Hu, Fan Zhang, Chang-Jian Lin

Journal of Electrochemistry

Titanium and its alloys have been widely used as medical implant materials because of their good mechanical properties and biocompatibility.However,the physiological corrosion of metal will release metal ions,resulting in toxic and side effects.In this paper,in order to improve the corrosion resistance of titanium,and to enhance its bioactivity and osseointegration,the surface modification of titamum were performed.Using eletrochemical methods Tafel polarization and electrochemical impedance spectroscopy(EIS) were applied to study the electrochemical corrosion behavior of TiO₂ /HA composite coating.It is indicated that the corrosion resistance of the prepared TiO₂ /Ti material in Tyrode's physiological solution is improved because of the enhanced …

Electrocatalytic Reduction Of L-Cystine At Pb/Nanotio2 Film Electrode, Dao-Bao Chu, Feng Wang, Ying Xiao, Xue-Jiao Zhang

Journal of Electrochemistry

The nanoporous Ti-based TiO₂ films electrodes modified with Pb particles(Pb/nanoTiO₂) were prepared by using anodization and potentiostatic electro-deposition.The optimum deposition conditions were determined by comparing with various deposition potentials and time.The SEM analyses indicated that the TiO₂ films were homogeneous nanoporous structure,and the Pb particles well dispersed on the TiO₂ films.The L-cystine electrocatalytic activity reduction on the Pb/nanoTiO₂ film electrodes was investigated by cyclic voltammetry and Chronoamperometric curves.The results showed that this type of the electrode posseses high acticity and stability.

Study Of Electrodes Modified With Hybrid Copper Cobalt Hexacyanoferrate-Mwcnts Composites, Shan Jiang, Yun Zhang, Xiao-Yan Wang, Xiao-Fei Yao

Journal of Electrochemistry

The hybrid modified electrodes were obtained by electrochemical deposition of copper-cobalt hexacyanoferrate(CuCoHCF) /multi-walled carbon nanotubes(MWCNTs) on the surface of glassy carbon electrode.The effects of the amount of MWCNTs and composition of electrolyte on the properties of modified electrode had been researched.The copper cobalt hexacyanoferrate-MWCNTs modified electrodes show excellent electrochemical properties compared with that modified only copper-cobalt hexacyanoferrate.The CuCoHCF-MWCNTs/GCE exhibits obvious electrocatalytic activity towards oxidation of hydrogen peroxide.The oxidation peak current increased linearly with the concentration of hydrogen peroxide in the range of 3.16 × 10^-5 ～ 2.92 × 10^-3 mol· L^-1.The linear equation is given up …

Preparation And Characterization Of Sulfur/Mesoprous Carbon Composite Cathodes, Wen-Hua Zhang, Yao Chen, Xin-Ping Ai, Yu-Liang Cao

Journal of Electrochemistry

A sulfur/mesoporous carbon composite was prepared by thermally treating a mixture of sublimed sulfur and mesoporous carbon. The microstructure of the mesoporous carbon was characterized by BET analysis and X-ray diffraction(XRD). The electrochemical performance of the S/C composite as cathode materials was evaluated by the galvanostatic method. The results confirmed that the mesoporous carbon could not only greatly enhance the electrochemical activity of sulfur electrode, but also effectively confine the diffusion of dissolved polysulfides in organic electrolyte. As a result,the S/C composites showed high capacity, good cycle performance and excellent rate capability. The specific capacity of the S/C composite was …

The Synthesise Of Electron-Conducting Redox Hydrogel And Its Application In Microbial Fuel Cell, Kai-Peng Wang, Sheng-Li Chen

Journal of Electrochemistry

Efficient electron transfer between the microbe and the anode is key for the electricity generation in Microbial fuel cell(MFC).Through the modification of anode,the rate of electron transfer can be accelerated,therefore the performance of MFC can be enhanced.In this paper,we report the synthesis of a type of electronconducting and bio-compatible redox hydrogel and its application.The hydrogel consists of poly(4-vinylpyridine) as backbone and neutral red as the redox center.By immobiliazing neutral red on the backbone through covalent bond,the secondary contamination due to the soluble redox mediator to external environment can be prevented.MFCs using the hydrogel-modified carbon anode significantly exhibit shorter acclimation period,and …

Electrochemical Properties Of Ni(Oh)2 Doped By Nio, Fei-Biao Chen, Bo-Rong Wu, Wei-Feng An, Zhao-Jun Yang, Feng Wu, Shi Chen

Journal of Electrochemistry

The Ni(OH)₂ cathode material of MH/Ni was doped by NiO,which behaves as a capacitor and can improve the charge-discharge rate capacity of Ni(OH)₂.The electrochemical properties of Ni(OH)₂ was characterized by charge-discharge curves and cyclic voltammetry.The results showed that the material had the best discharge property when doped by 5% NiO,and the discharge specific capacity could reach 310.1 mAh/g at 0.2 C rate and remianed 79.5% at 3 C rate.The difference oxidation and reduction potentials between the of the battery was 164 mV when the Ni(OH)₂ was doped by 5% NiO,which showed a good cyclic property.

Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.

Electrosynthesis Of P-Aminobenzenearsenic Acid, Chun-An Ma, Qin-An Zheng, Qiang Zhou, Ying-Hua Xu

Journal of Electrochemistry

The electrochemical reduction of p-nitrophenyl arsonit acid to p-aminobenzenearsenic acid was studied using controlled-current electrolysis.The results showed that the yield of p-aminobenzenearsenic acid was determinated by the following factors:the concentrations of sulphuric acid,the amount of additive,temperature and the concentrations of p-nitrophenyl arsenic acid.The optimum electrolytic conditions were obtained to be is 10% H₂SO₄,1% NaCl,80 ℃,25 g/350 mL p-nitrophenyl arsenic acid and 10 A·dm^-2.The yield of arsanilic acid could be reached 64.7% under the optimum electrolytic conditions.

Cobalt-Doped Todorokite Prepared By Refluxing At Atmospheric Pressure As Lithium-Ion Battery Cathode, Rui-Qi Li, Chun-Hua Song, Chao Xu, Li-Xing Tu, Guo-Hong Qiu, Fan Liu

Journal of Electrochemistry

Cobalt-doped todorokites were prepared by refluxing at atmospheric pressure,and then charactered by X-ray diffraction(XRD),thermogravimetry(TG) and the analysis of chemical compositions.These measurements showed that all of the refluxing products were single phase of todorokites and the structure formulas were Mg_xCo_yMnO_z·nH₂O,where 0.18 ≤ x ≤ 0.22,0 ≤ y ≤ 0.24,2.10 ≤ z ≤ 2.53,and 0.35 ≤ n ≤0.73.The electrochemical characteristics of cobalt-doped todorokites were examined as lithium insertion hosts for cathodes in rechargeable lithium batteries.The first discharge capacity of undoped todorokite electrode was 211 mAh/g and the discharge capacity became 37 mAh/g after 30 …

Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Lscm-Ceo2 Catalyst Layer In Thin Film Sofc, Yun-Yun Wang, Bo Huang, Xin-Jian Zhu, Wan-Qi Hu, Qing-Chun Yu

Journal of Electrochemistry

Solid oxide full cell(SOFC) running directly on hydrocarbon fuels has attracted much attention in recent years. In this paper, a dual-layer structure anode was fabricated by tape casting and screen printing method. The addition of a LSCM-CeO₂ catalyst layer to the supported anode surface yielded better performance in ethanol fuel. The maximum power density reached 710 and 669 mW/cm² at 850 ℃ running on hydrogen gas steam and ethanol steam,respectively. No significant degradation in performance has been observed after 216 h of cell testing when the Ni-ScSZ13 anode was exposed to the ethanol steam at 700 ℃. Very …

An Ab-Initio Study Of The Elastic Properties Of Important Group Iv Diborides At High Temperatures, Manny Gonzales

Open Access Theses & Dissertations

Presented is an ab-initio Molecular Dynamics (MD) study, employing the Density Functional Theory (DFT), of the lattice parameter, thermal expansion coefficients and elastic constants of ZrB₂, TiB₂ and HfB₂ as a function of temperature. The MD trajectories provide the equilibrium lattice parameters at finite temperatures, and the gradient of the energy from these equilibrium solutions is then used to calculate the components of the stiffness tensor. The results for ZrB₂ are shown to agree well with reported experimental results for the lattice parameters and elastic constants as a function of temperature.

Spectroscopic Study Of The Inhibition Of Calcium Oxalate Calculi By Larrea Tridentata, Luis Alonso Pinales

Open Access Theses & Dissertations

The causes of urolithiasis include such influences as diet, metabolic disorders, and genetic factors which have been documented as sources that aggravate urinary calculi depositions and aggregations, and, implicitly, as causes of urolithiasis. This study endeavors to detail the scientific mechanisms involved in calcium oxalate calculi formation, and, more importantly, their inhibition under growth conditions imposed by the traditional medicinal approach using the herbal extract, Larrea tridentata. The calculi were synthesized without and with Larrea tridentata infusion by employing the single diffusion gel technique. A visible decrease in calcium oxalate crystal growth with increasing amounts of Larrea tridentata herbal infusion …

Temporal Scales For Transport Patterns In The Gulf Of Finland, Bert Viikmae, Tarmo Soomere, Mikk Viidebaum, Mihhail Berezovski

Publications

The basic time scales for current-induced net transport of surface water and associated time scales of reaching the nearshore in the Gulf of Finland, the Baltic Sea, are analysed based on Lagrangian trajectories of water particles reconstructed from three-dimensional velocity fields by the Rossby Centre circulation model for 1987–1991. The number of particles reaching the nearshore exhibits substantial temporal variability whereas the rate of leaving the gulf is almost steady. It is recommended to use an about 3 grid cells wide nearshore area as a substitute to the coastal zone and about 10–15 day long trajectories for calculations of the …

Waves In Materials With Microstructure: Numerical Simulation, Mihhail Berezovski, Arkadi Berezovski, Juri Engelbrecht

Publications

Results of numerical experiments are presented in order to compare direct numerical calculations of wave propagation in a laminate with prescribed properties and corresponding results obtained for an effective medium with the microstructure modelling. These numerical experiments allowed us to analyse the advantages and weaknesses of the microstructure model.

College Of Engineering Senior Design Competition Fall 2009, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Each student in his or her senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. The senior design project encourages the student to use everything learned in the engineering program to create a practical, real-world solution to an engineering challenge.

A highlight of the year-long senior design project is the senior design competition. This competition, which usually takes place the week before finals each semester, helps focus the senior students on increasing the quality and potential for commercial application for their design projects.

Judges from local industry evaluate the projects on innovation, commercial …

Indirect Electrosynthesis Of Double Aldehyde Starch Using Pb-(Bro3-/Br-) As Electro-Catalytic Mediator, Ni-Na Chen, Ri-Yao Chen, Xi Zheng, Xiao Chen, Zhen Chen

Journal of Electrochemistry

In this paper,Nafion membrane was used as the separator in the electrolysis cell to indirectly electro-generating the double aldehyde starch(DAS) with BrO₃^-/Br^-as a redox mediator and Pb as an anode.Effects of temperature,concentration of sulfuric acid and starch on the electro-oxidation of DAS were discussed.The steady state polarization curves were obtained.The experiment results showed that the current efficiency was over 50% when the electrolysis current density was 15mA/ cm².

Preparation Of Polyaniline/Polyester Conductive Fabric Via In-Situ Polymerization, Fang Na, Wei Wang

Journal of Electrochemistry

The formation of PANI coating on the surface of PET fiber and fabric was obtained by in-situ polymerization method.The coating′s thickness was about 1～2 μm.Orthogonal test methodology was used to analyze the main factors of preparation of PANI / PET conductive fabric.The effects of the aniline monomer concentration,oxidant: aniline molar ratio,doping acid concentration and types,reaction time on the conductivities of the fabric were studied.The structure of the polymer were characterized by SEM,FTIR and XRD.The results indicated that there was uniform and continuous polyaniline film on the surface of polyester fabric.The contents of oxidation and reduction of polyaniline molecular chain structure …

Progresses In Electrocatalysis Of Nanomaterials—Tuning The Surface Structure And Property Of Electrocatalysts, Yan-Xia Jiang, Na Tian, Zhi-You Zhou, Sheng-Pei Chen, Shi-Gang Sun

Journal of Electrochemistry

The property of an electrocatalyst depends strongly on its surface structure.The study of surface structure-catalytic functionality is the base of design and preparation of electrocatalysts of high activity,high stability and high selectivity at microstructure level.In this paper,based mainly on our results concering hydrogen and oxygen adsorption-desorption,ethylene glycol oxidation and CO₂ reduction,the research progresses in tuning the surface structure and property of electrocatalysts are summarized.This paper overviews firstly the cyclic voltammetric characteristics,electrocatalytic properties of platinum single crystal planes lying on different crystallographic zones of the unit stereographic triangle of face-centered cubic(fcc) metals.Next,the innovation of electrochemical methods to control the surface …

Electrooxidation Of Formic Acid On Pd-Ni Alloy Film Electrode-The Effect Of Dealloying, Chao Wang, Fei-Fei Shi, Jin-Yi Wang, Han-Xuan Zhang, Wen-Bin Cai

Journal of Electrochemistry

A Pd-Ni alloy film was electrodeposited on Au disc electrode at a constant potential from a weakly basic bath containing PdCl₂,NiSO₄ and ethylenediamine.The as-deposited film was then subjected to potential cycling in a perchloric acid solution for surface dealloying treatment.The dealloyed Pd-Ni film electrode was examined for the electrocatalytic oxidation of formic acid,and compared with the as-deposited one as well as a Pd film electrode.The FE-SEM and electrochemical measurements on the Pd-Ni films revealed that the dealloying treatment caused a surface roughening and an increase in specific surface reaction area.The ICP-AES and XPS analyses demonstrated that the …

Electrocatalysis In Polymer Electrolyte Membrane Fuel Cells, Li Li, Si-Guo Chen, Xue-Qiang Qi, Yao-Qiong Wang, Meng-Bo Ji, Lan-Lan Li, Zi-Dong Wei

Journal of Electrochemistry

This review presents the study of Chongqing University in electrocatalysis for polymer electrolyte membrane fuel cells(PEMFCs).Based on the understanding to the performance degradation of PEMFCs' catalysts,the university has being concentrated on how to increase the activity,stability and utility of noble metal catalysts.It covers the molecular design of near-surface alloy catalysts for improvement of activity to oxygen reduction reaction(ORR) and resistance to foreign poison species,selective deposition of Pt on the so-called "three-phase interface" for a high Pt utility,and invention of anti-flooding electrode against water flooding in the catalyst layer of the membrane assemble electrode(MEA),and so on.The catalytic mechanism of electrode reactions …

Highly Durable Pt/Ruo2/C Catalyst For The Cathode Of Direct Methanol Fuel Cells, Chun-Yu Du, Tao Dong, Ge-Ping Yin, Peng-Fei Shi

Journal of Electrochemistry

Instability of the carbon-supported Pt(Pt/C) catalyst at the cathode is one of the key technical challenges for the development of Direct Methanol Fuel Cells(DMFCs).In this paper,an efficient approach to enhancing the stability of the cathode catalyst was explored by designing and synthesizing a novel nanocomposite support,RuO₂ coated carbon black(RuO₂/C).Firstly,a wet chemical method was employed to synthesize the RuO₂/C nanocomposite,from which Pt/RuO₂/C catalyst was further prepared by a microwave method.The morphology and crystalline structure of the RuO₂/C support and Pt/RuO₂/C catalyst were then characterized by TEM and XRD.Finally,the electrochemical performance …

Synthesis And Electrocatalytic Properties Of Ni-Pd/C Catalysts With Pd-Enriched Surface, Yu-Mei Chen, Zhi-Xiu Liang, Sheng-Li Chen

Journal of Electrochemistry

The Ni-Pd alloy catalysts with Pd-enriched surface were synthesized through a modified polyol process.The synthesized materials were investigated by XRD and electrochemical methods,and tested as electrocatalysts for CH₃OH-tolerant oxygen reduction.The results indicated that the synthesized Ni-Pd nanoparticles possess multiple phases containing Pd-Ni alloy and pure Ni.Comparing with Pd/C,the prepared Ni-Pd/C nanoparticles exhibited better resolved voltammetric peaks between the hydrogen absorption and adsorption,and positively shifted current peaks for the reduction of Pd oxide.The prepared Ni-Pd alloys with Pd-enriched surface have significantly enhanced ORR activity and improved CH₃OH tolerance as comparing with Pd/C catalysts.

Complex Reduction Preparation Of Carbon Supported Pd Nanoparticle Catalyst And Its Electrocatalysis For Formic Acid Oxidation, Wei He, Yong-Yin Kang, Chong Du, Zhi-Qing Zou, Xiao-Gang Zhang, Hui Yang

Journal of Electrochemistry

A simple procedure involved the complexing of PdCl₂ with sodium citrate followed by ethylene glycol reduction has been employed for the preparation of carbon-supported Pd nanoparticles(Pd/C).The XRD and TEM characterizations indicate that Pd nanoparticles with a small particle size were well-dispersed on carbon support.The mean particle sizes of the Pd/C catalysts were found to be increased from 2.7 to 5.8 nm with heat-treatments at different temperature.The mass activity of the Pd/C catalyst for formic acid electrooxidation increased with the decrease in Pd particle size.However,the specific activity increased with Pd particle size.Furthermore,the Pd/C catalyst with a particle size of ca.3.6 …

Electrocatalytic Performance Of Carbon Supported Ir Catalysts With Different Ir Loadings For Ammonia Oxidation, Yu-Zhi Jiang, Qing-Mei Kong, Tian-Hong Lu, Yi-Ming Zhou, Ya-Wen Tang

Journal of Electrochemistry

The electrocatalytic performance of the Ir/C catalyst as the anodic catalyst in the amperometric and electrochemical NH₃ sensor was investigated.The experimental results illustrated that in the NaClO₄ neutral electrolyte,the electrocatalytic performance of the Ir/C catalyst for the NH₃ oxidation is related to the Ir loading in the Ir/C catalyst.Among the Ir/C catalysts with different Ir loading,the best electrocatalytic activity,stability and sensitivity were achieved by the Ir/C catalyst with 10% Ir loadings.In addition,the current densities of the NH₃ oxidation at the Ir/C catalysts with the different Ir loadings were linearly proportional to the NH₃ concentration.The Ir/C …

Cyclic Voltammetric And In-Situ Ftir Spectroscopic Studies Of Adsorption And Reduction Of No On Electrode Of Pt Nanoparticles, Qian Cheng, Yan-Xia Jiang, Dong-Mei Zeng, Shi-Gang Sun

Journal of Electrochemistry

Adsorption and reduction of NO on electrode of Pt nanoparticles in acid solutions were studied by means of cyclic voltammetry(CV) and in-situ FTIR spectroscopy.The results indicated that the reduction of NO is a complicated process including the adsorption of NO on electrode surface.Two types of surface-bonded NO were determined on Pt nanoparticles.The weakly adsorbed NO was reduced between 0.6 V and-0.05 V,which yielded nitrous oxide(N₂O) and ammonium(NH₄⁺) as products;while the strongly bonded NO was reduced at more negative potentials between-0.05V and-0.15V,producing only NH₄⁺ species.