Engineering Science and Materials Commons^™

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

Investigation On The Effects Of Biofouling On The Boundary Layer, Adam N. Bacon

LSU New Orleans Theses and Dissertations

This study is an investigation of the effect of biofouling on the boundary layer of a flat plate and a NACA 4-digit series foil. Three identical hydrofoils made of resin were placed in the Gulf of Mexico at Grand Isle, Louisiana, and observed and analyzed by marine biologists at the University of New Orleans for their species composition. The resulting biofouling that grew was primarily made up of barnacles and bryozoans. The foils were submerged in an open channel flume at zero incidence and subjected to a series of experiments whose arc-length Reynolds numbers ranged from approximately 13000 to 32000. …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Numerical Simulation Of Laser Induced Elastic Waves In Response To Short And Ultrashort Laser Pulses., Alireza Zarei

All Dissertations

In an era of intensified market competition, the demand for cost-effective, high-quality, high-performance, and reliable products continues to rise. Meeting this demand necessitates the mass production of premium products through the integration of cutting-edge technologies and advanced materials while ensuring their integrity and safety. In this context, Nondestructive Testing (NDT) techniques emerge as indispensable tools for guaranteeing the integrity, reliability, and safety of products across diverse industries.

Various NDT techniques, including ultrasonic testing, computed tomography, thermography, and acoustic emissions, have long served as cornerstones for inspecting materials and structures. Among these, ultrasonic testing stands out as the most prevalent method, …

Analysis Of Drying Behavior Of Robocasted Barium Titanate, Abigail Ortega

Open Access Theses & Dissertations

Finding an adequate ceramic formulation for material extrusion is a time-consuming process. The necessary equipment may be unavailable to perform the desired test. This study demonstrated an alternative to observe a material after extrusion to understand its drying process. This study focused on 55 solid loading volume percent and a 39 solid loading volume percent, each with two different binder treatments focusing on fresh same day made binder, a 30 day old, aged binder and lastly an artificial binder obtained by a fuming process. Firstly, a formulation was created and loaded onto a pressure-based syringe to be extruded with a …

A Manufacturing-To-Response Pathway For Manufacturing Optimization Of Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Dissertations

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Comparison Of Meteorological Drought Indices In Tanzania Using The Meteorological Drought Monitoring Software Package, Paul Ts Limbu

Tanzania Journal of Engineering and Technology (TJET)

Low precipitation, substantial evaporation, and an unequal distribution of precipitation throughout the area are the characteristics of drought, a climatic abnormality. This study used the Meteorological Drought Monitoring (MDM) software and monthly rainfall data from the Tanzania Meteorological Authority (TMA) to examine and compare the Deciles Index (DI), Standardised Precipitation Index (SPI), Percent of Normal Index (PNI), Rainfall Anomaly Index (RAI), Z-Score Index (ZSI), China-Z Index (CZI), and Modified China-Z Index (MCZI) for drought monitoring in Tanzania from 1988 to 2017. It was found that ZSI represented the dry years better than other indices, followed by DI, RAI, PNI, SPI, …

Thermal Performance Investigation Of Thermoelectric Cooling System With Various Hot-Side Cooling Methods, Bowo Y. Prasetyo, Parisya P. Rosulindo, Fujen Wang

Makara Journal of Technology

Thermoelectric devices have been widely used in various applications, including cooling and power generation. The potential application of thermoelectric cooling systems has been studied. However, these systems still face challenges in achieving optimal performance compared with other cooling systems. Several factors, including the hot-side cooling method, influence the performance of thermoelectric systems. This study aimed to investigate the effects of different hot-side cooling methods on the thermoelectric performance and thermal behavior of thermoelectric cooling systems. The testing methods involved the combination of the thermoelectric module with five hot-side heat exchangers, including a square heatsink, a round heatsink, a two-pipe heat …

Injectable And Rapidly Expandable Thrombin-Decorated Cryogels Achieve Rapid Hemostasis And High Survival Rates In A Swine Model Of Lethal Junctional Hemorrhage, Syed Muntazir Andrabi, S.M. Shatil Shahriar, Al-Murtadha Al-Gahmi, Benjamin L. Wilczewski, Mark A. Carlson, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Effective therapies are urgently needed to stabilize patients with marginally compressible junctional hemorrhage long enough to get them to the hospital alive. Herein, we report injectable and rapidly expandable cryogels consisting of polyacrylamide and thrombin (AT cryogels) created by cryo-polymerization for the efficient management of lethal junctional hemorrhage in swine. The produced cryogels have small pore sizes and highly interconnected porous architecture with robust mechanical strength. The cryogels exhibit rapid shape memory properties and prove to be resilient against fatigue. These cryogels also show high water/blood absorption capacity, fast blood clotting effect, and enhanced adhesion of red blood cells and …

Numerical Analysis Of Flow Fields For The Different Models Of The Shrouded Savonius Rotor, Alsaied Khalil Mahmoud, Mohamed Mahgoub Bassuoni, Mohamed Fawzy Obiaa, Ahmed Mostafa Khaira

Journal of Engineering Research

In this study, the effect of three different lengths (short, medium, and long) of flanged shrouded Savonius wind turbines is investigated three-dimensional (3-D) numerically by ANSYS-FLUENT. The 3-D numerical model of a simple rotor is validated by comparing the results with previous published experimental ones at the same operating conditions and geometry. The numerical and experimental results indicate a good agreement with each other when using the SST K-ω model with a time step size of 0.0025 s.The analysis of the numerical results of the three flanged shrouded models shows an enhancement of the torque coefficient at tip speed ratio …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto

Faculty Publications

Residual stresses developed during additive manufacturing (AM) can influence the mechanical performance of structural components in their intended applications. In this study, thermomechanical residual stress simulations of the laser powder bed fusion (LPBF) process are conducted for both simplified (plate and cube-shaped) geometries as well as five complex lattice geometries fabricated with Inconel 718. These simulations are conducted with the commercial software package Simufact Additive©, which uses a nonlinear finite element analysis and layer-by-layer averaging approach in determining residual stresses. To verify the efficacy of the Simufact Additive© simulations, numerical results for the plate and cube-shape geometries are analyzed for …

Copper−Cystine Biohybrid-Embedded Nanofiber Aerogels Show Antibacterial And Angiogenic Properties, Anik Karan, Navatha S. Polavaram, Margarita Darder, Yajuan Su, Syed Muntazir Andrabi, S M Shatil Shahriar, Johnson V. John, Zeyu Luo, Mark A. Decoster, Yu Shrike Zhang, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Copper−cystine-based high aspect ratio structures (CuHARS) possess exceptional physical and chemical properties and exhibit remarkable biodegradability in human physiological conditions. Extensive testing has confirmed the biocompatibility and biodegradability of CuHARS under diverse biological conditions, making them a viable source of essential Cu²⁺. These ions are vital for catalyzing the production of nitric oxide (NO) from the decomposition of Snitrosothiols (RSNOs) found in human blood. The ability of CuHARS to act as a Cu²⁺ donor under specific concentrations has been demonstrated in this study, resulting in the generation of elevated levels of NO. Consequently, this dual function makes …

Implantation Of A Capsular Tension Ring During Cataract Surgery Attenuates Predicted Remodeling Of The Post-Surgical Lens Capsule Along The Visual Axis, Kurt A. Ameku, Caleb C. Berggren, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Cataract surgery permanently alters the mechanical environment of the lens capsule by placing a hole in the anterior portion and implanting an intraocular lens (IOL) that has a very different geometry from the native lens. We hypothesized that implant configuration and mechanical interactions with the post-surgical lens capsule play a key role in determining long-term fibrotic remodeling.

Methods: We developed the first finite element-growth and remodeling (FE-G&R) model of the post-surgical lens capsule to evaluate how implantation of an IOL with and without a capsular tension ring (CTR) impacted evolving lens capsule mechanics and associated fibrosis over …

Engineering Neurotoxin-Functionalized Exosomes For Targeted Delivery To The Peripheral Nervous System, Mena Asha Krishnan, Olawale A. Alimi, Tianshu Pan, Mitchell Kuss, Zeljka Korade, Guoku Hu, Bo Liu, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The administration of therapeutics to peripheral nerve tissue is challenging due to the complexities of peripheral neuroanatomy and the limitations imposed by the blood–nerve barrier (BNB). Therefore, there is a pressing need to enhance delivery effectiveness and implement targeted delivery methods. Recently, erythrocyte-derived exosomes (Exos) have gained widespread attention as biocompatible vehicles for therapeutics in clinical applications. However, engineering targeted Exos for the peripheral nervous system (PNS) is still challenging. This study aims to develop a targeted Exo delivery system specifically designed for presynaptic terminals of peripheral nerve tissue. The clostridium neurotoxin, tetanus toxin-C fragment (TTC), was tethered to the …

Yap Mechanotransduction Under Cyclic Mechanical Stretch Loading For Mesenchymal Stem Cell Osteogenesis Is Regulated By Rock, Eunju Kim, Brandon D. Riehl, Tasneem Bouzid, Ruiguo Yang, Bin Duan, Henry J. Donahue, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

While yes-associated protein (YAP) is now recognized as a potent mechanosensitive transcriptional regulator to affect cell growth and differentiation including the osteogenic transcription of mesenchymal stem cells (MSCs), most studies have reported the YAP mechanosensing of static mechanophysical cues such as substrate stiffness. We tested MSC response to dynamic loading, i.e., cyclic mechanical stretching, and assessed YAP mechanosensing and resultant MSC osteogenesis. We showed that cyclic stretching at 10% strain and 1 Hz frequency triggered YAP nuclear import in MSCs. YAP phosphorylation at S127 and S397, which is required for YAP cytoplasmic retention, was suppressed by cyclic stretch. We also …

Me-Em 2022-23 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Research Updates
• Curriculum and Instruction
• Facilities
• New Faculty
• Research, Machine Learning
• Research, Ana Dyreson
• In Memoriam
• Student Success
• Alumni Profile and Activity
• Graduates
• Faculty Awards and Honors
• Patents and Publications
• Donors
• Grants and Contracts

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Deep Learning Based Optical Flow Analysis Of High-Speed Flows, Daniel H. Zhang, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

Two-dimensional Rayleigh scattering imaging is utilized to quantify the high-speed flow velocity by employing deep learning based optical flow analysis, along with density fields from Rayleigh scattering intensity profiles.

Long-Term Simulation Of Stem Cell Mechanobiology, Manoochehr Rabiei

Mechanical and Aerospace Engineering Dissertations - Archive

An accurate representation of cellular mechanobiology necessitates the inclusion of subcellular elements characterized by minute masses and dimensions. These minute objects yield multiscale dynamic models with disproportionate terms, which require inordinate amounts of computational time to simulate. The computational requirements limit the time span of the simulation to time histories shorter than one second, even when employing supercomputers. This work presents a high-speed approach to simulating the mechanobiology of stem cells. The proposed approach separates the computational time from the size, and distribution, of masses of the subcellular elements, enabling the simulation of weeks-long cellular processes within hours on a …

Generating Blood Analog For Laser Induced Fluorescent Particle Image Velocimetry, Chungyiu Ma, Jared Chong, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

To mimic blood non-Newtonian viscosity features under designated temperatures from 305 to 315 K, transparent blood analogs were generated by the mixture of xanthan gum and deionized water with fluorescent particles for laser induced fluorescent particle image velocimetry.

Dueling Robot, Abigail Coy

All Undergraduate Projects

This project was undertaken as a personal challenge to combine a Mechanical Engineering Technology degree and an Electrical Engineering Technology degree into a single final project showing the cumulative knowledge gained. It was determined that a robot to participate in Western Allied Robotics would be designed and manufactured for the 3 lb. weight class.

A two-part power system was designed to provide more power to the weapon arm. This design combined a compressive spring’s kinetic energy with the torque from the electric motor. Research determined all of the purchased components required and analysis were performed to determine the geometry and …

3d Flow Field Quantification In An Artery Model Using Optical Flow Method Based On Simulated Multi-Angle Angiography, Zifeng Yang, Hang Yi, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

3D flow field in a numerically simulated arterial model is quantified using the three-dimensional optical flow method based on simulated simultaneous multi-angle X-ray angiography of the blood flow with contrast agent perfusions.

Mechanics Of Pure Bending And Eccentric Buckling In High-Strain Composite Structures, Jimesh D. Bhagatji, Oleksandr G. Kravchenko, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This paper presents fabrication, experimental testing, and progressive failure modeling to study the deformation of an ultra-thin composite beam. The research study examines the deformation modes of a post-deployed boom under repetitive pure bending loads using a four-point bending setup and …

Insights Into The Characterization And Degradation Of Electrospun Polycaprolactone Scaffolds For Tissue Engineering Applications, Caleb B. Wells

Theses and Dissertations

Electrospun polymeric biodegradable scaffolds are essential in tissue engineering, particularly for Engineered Tissue Vascular Grafts (ETVGs), which promise advancements in treating coronary artery disease, peripheral arterial disease, congenital cardiovascular defects, and renal disease. These scaffolds present a solution to issues with autologous graft availability and durability. While large-diameter grafts in low-pressure environments have seen success, small-diameter grafts in high-flow scenarios remain challenging. Understanding polymeric scaffold degradation and behavior during incubation, especially under dynamic mechanical loading, is vital for clinical translation of small-caliber ETVGs.

This research focuses on characterizing the mechanical and microstructural properties of electrospun polycaprolactone (PCL) scaffolds and their …

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Dual Airfoil Testing System, Zifeng Yang, Collin Charvat, Jack Stafford, Kyle Mathews, Logan Kelly

Mechanical and Materials Engineering Faculty Publications

A dual airfoil testing system includes a platform including a frame defining a chamber that is configured to receive a horizontal flow of air for testing a first airfoil and a second airfoil contained in the chamber and a control system including a controller to control a first attack angle stepper motor, a second attack angle stepper motor, at least one gap stepper motor, and at least one stagger stepper motor. The controller is configured to automatically control and adjust the stepper motors to control and adjust the attack angle of the first airfoil, the attack angle of the second …