Engineering Science and Materials Commons^™

Comparison Of Fuzzy Clustering Methods And Their Applications To Geophysics Data, David J. Miller, Carl A. Nelson, Molly Boeka Cannon, Kenneth P. Cannon

Department of Mechanical and Materials Engineering: Faculty Publications

Fuzzy clustering algorithms are helpful when there exists a dataset with subgroupings of points having indistinct boundaries and overlap between the clusters. Traditional methods have been extensively studied and used on real-world data, but require users to have some knowledge of the outcome a priori in order to determine howmany clusters to look for. Additionally, iterative algorithms choose the optimal number of clusters based on one of several performance measures. In this study, the authors compare the performance of three algorithms (fuzzy c-means, Gustafson-Kessel, and an iterative version of Gustafson-Kessel) when clustering a traditional data set as well as real-world …

Experimental Investigation Of A Novel Blast Wave Mitigation Device, Zhenbi Su, Wen Peng, Zhaoyan Zhang, George Gogos, Reed Skaggs, Bryan Cheeseman, Chian Fong Yen

Department of Mechanical and Materials Engineering: Faculty Publications

A novel blast wave mitigation device was investigated experimentally in this paper. The device consists of a pistoncylinder assembly. A shock wave is induced within the cylinder when a blast wave impacts on the piston. The shock wave propagates inside the device and is reflected repeatedly. The shock wave propagation process inside the device lengthens the duration of the force on the base of the device to several orders of magnitude of the duration of the blast wave, while it decreases the maximum pressure over an order of magnitude. Two types of experiments were carried out to study the blast …

Me-Em 2009 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Energy Systems
• Health Systems
• Faculty & Staff
• Students
• Alumni
• Resources
• Graduates
• Publications
• ME-EM Community

The Role Of Silicon Content On Environmental Degradations Of T91 Steels, Ajit K. Roy, D. Maitra, Pankaj Kumar

Mechanical Engineering Faculty Research

T91 grade steels showed a gradual enhancement in tensile ductility at ambient temperature due to an increase in Si content from 0.5 to 2.0 weight percent (wt.%). However, the ultimate tensile strength was reduced only above 1.5 wt.% Si. The corrosion potential became more active in an acidic solution with increasing temperature. The cracking susceptibility in a similar environment under a slow-strain-rate (SSR) condition was enhanced at higher temperatures showing reduced ductility, time to failure, and true failure stress. Cathodic potentials applied to the test specimens in SSR testing caused an enhanced cracking tendency at 30 and 60°C, suggesting hydrogen …

Tensile Deformation Of A Nickel-Base Alloy At Elevated Temperatures, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam

Mechanical Engineering Faculty Research

The results of tensile testing involving Waspaloy indicate that the failure strain was gradually reduced at temperatures ranging between ambient and 300 °C. Further, serrations were observed in the engineering stress versus strain diagrams in the temperature range of 300-600 °C. The reduced failure strain and the formation of serrations in these temperature regimes could be the result of dynamic strain aging of this alloy. The extent of work hardening due to plastic deformation was reduced at temperatures above 300 °C. A combination of ductile and intergranular brittle failures was seen at temperatures above 600 °C. γ′ was detected at …

Study Of Multibody Dynamics Using Matlab, Kalyani Soman

Mechanical & Aerospace Engineering Theses & Dissertations

Research in computational dynamics has gained importance in the past few years because of the demand for analysis and simulation of various multi-body systems in the growing mechanical and aerospace industry. These multi-body systems are made of individual bodies that are interconnected via mechanical joints. Mathematically, these joints that connect the bodies can be described as constraint equations imposed upon the motions of the involved free bodies. This process will result in an equation of motion expressed in the form of a differential-algebraic equation. It is the main objective of this thesis to develop a solution algorithm that can take …

Me-Em 2008 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Engineering Education
• Students
• Alumni
• Resources
• Graduates
• Publications
• ME-EM Community

Control Of The Nanoscale Crystallinity And Phase Separation In Polymer Solar Cells, Chih-Wei Chu, Hoichang Yang, Wei-Jen Hou, Jinsong Huang, Gang Li, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Grazing-incidence x-ray diffraction and atomic force microscopy were performed on bulk heterojunction regioregular poly(3-hexylthiophene) (RR-P3HT) [6,6]-phenyl-C₇₁-butyric acid methyl esters spin-cast films with different film processing conditions to correlate the crystalline nanostructure of P3HT with the corresponding solar cell performance. The increase in long wavelength absorption for solvent annealed films is related to highly conjugated crystal structure of RR-P3HT phase-separated in the active layer. Upon thermal annealing, the solvent annealed 50-nm-thick device shows high solar cell performance with fill factor up to 73% and power conversion efficiency of 3.80%.

Stereolithography Of Poly(Ethylene Glycol) Hydrogels With Application In Tissue Engineering As Peripheral Nerve Regeneration Scaffolds, Karina Arcaute

Open Access Theses & Dissertations

In recent years, rapid prototyping (RP) technologies initially developed to create prototypes prior to production for the automotive, aerospace, and other industries, have found applications in tissue engineering (TE). Several different RP technologies are being used to fabricate biocompatible 3D structures with controlled micro- and macro-scale characteristics. The focus of this research was to explore the capabilities of the RP technology, stereolithography (SL), for creating complex, 3D scaffolds with applications in TE using a photocrosslinkable biopolymer, poly(ethylene glycol) (PEG). The primary objective was to create an implantable multi-lumen nerve guidance conduit (NGC) for the regeneration of peripheral nerves.

Studies of …

Modelagem Da Vida De Fadiga E Do Acúmulo De Deformações Permanentes Em Pavimentos Asfálticos Por Meio De Um Modelo De Dano Contínuo, Victor Ferreira Teixeira, Flavio V. Souza, Jorge Barbosa Soares

Department of Mechanical and Materials Engineering: Faculty Publications

: It is known that the conditions of the Brazilian roadways have an enormous impact over the national economy. In face of this problem, there is a need for new methodologies for pavement analyses and design that can more accurately predict pavement distresses. Among the main methods currently used, one can find purely empirical methods and mechanistic-empirical methods which make use of the pavement structure response. The evolution of numerical methods such as the Finite Element Method (FEM) or the Boundary Element Method (BEM) has made the mechanistic-empirical methods more popular for pavement analysis applications. This work shows a mechanistic …

College Of Engineering Senior Design Competition Spring 2007, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Me-Em 2007 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Research Expansion
• Research Groups
• Faculty & Staff
• Students
• Alumni
• Resources
• Graduates
• Publications

Improved Hole-Injection Contact For Top-Emitting Polymeric Diodes, Juo-Hao Li, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this letter, an efficient hole-injection contact was achieved for the top-emitting polymeric light-emitting diodes (PLEDs). The anode has a structure of metal/molybdenum oxide/ poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS). It has been found that hole injection was significantly improved by inserting a thin layer of MoO₃ between aluminum and PEDOT:PSS. An ultraviolet photoelectron spectroscopy (UPS) was used to investigate the change of work function, and photovoltaic measurement confirmed that the improved hole injection is due to the reduction of barrier height, resulted from the addition of transition metal oxide. PEDOT:PSS layer was found necessary in anode structure to further enhance the …

Influence Of Van Der Waals Forces On Increasing The Strength And Toughness In Dynamic Fracture Of Nanofibre Networks: A Peridynamic Approach, Florin Bobaru Ph.D.

Department of Engineering Mechanics: Faculty Publications

The peridynamic method is used here to analyse the effect of van der Waals forces on the mechanical behaviour and strength and toughness properties of three-dimensional nanofibre networks under imposed stretch deformation. The peridynamic formulation allows for a natural inclusion of long-range forces (such as van der Waals forces) by considering all interactions as ‘long-range’. We use van der Waals interactions only between different fibres and do not need to model individual atoms. Fracture is introduced at the microstructural (peridynamic bond) level for the microelastic type bonds, while van der Waals bonds can reform at any time. We conduct statistical …

Time-Economic Lifetime Assessment For High Performance Thermal Barrier Coating Systems, Marion Bartsch, Bernd Baufeld, S. Dalkilic, Iulian Mircea, K. Lambrinou, T. Leist, J. Yan, Anette M. Karlsson

Mechanical Engineering Faculty Publications

Strategies for time-economic lifetime assessment of thermal barrier coatings (TBC) in service are described and discussed on the basis of experimental results, achieved on material systems with coatings applied by electron beam physical vapour deposition. Service cycles for gas turbine blades have been simulated on specimens in thermo-mechanical fatigue tests, accelerating the fatigue processes by an increase of load frequency. Time dependent changes in the material system were imposed by a separate ageing, where the samples were pre-oxidized prior to the fatigue test. Results of thermo-mechanical fatigue tests on pre-aged and as-coated specimens gave evidence of interaction between fatigue and …

Low Voltage And Fast Speed All-Polymeric Optocouplers, Yan Yao, Hsiang-Yu Chen, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

An all-polymeric optocoupler has been demonstrated with a polymer light-emitting diode (PLED) as the light source (input unit) and a polymer/fullerene photodiode (PD) as the detector (output unit). The electroluminescence (EL) peak of the PLED is 560 nm, and the entire EL spectrum is within the response range of the PD. The optocoupler can work at low driving voltages, 5 V on the PLED and 0 V on the PD. The output photocurrent increases linearly with input current, and the current density transfer ratio reaches 1.5%. The frequency response of the optocoupler is at 500 kHz. With comparable performance to …

Origin Of Photomultiplication In C60 Based Devices, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this manuscript, the origin of the photomultiplication effect was studied in C₆₀ based devices by evaluating the wavelength dependent external and internal quantum efficiencies under various biases. The effect of materials with disordered structures on the photomultiplication effect was determined by intentionally integrating both ordered and disordered material structures into one organic solar cell device with a configuration of indium tin oxide/poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS)/pentacene/C₆₀ fullerene/bathocuproine (BCP)/Al. Our results show that both the disordered structure of C₆₀ and the charge trapping effect at the C₆₀ /PEDOT:PSS interface contribute to the photomultiplication effect. By studying the C60-only …

Deck-Mounted Steel Post Barrier System, John D. Reid, Ronald K. Faller, Jason A. Hascall

Department of Mechanical and Materials Engineering: Faculty Publications

An existing mountable safety barrier system, previously crash tested successfully on a wood bridge deck, was evaluated for use on a fiber reinforced plastic (FRP) bridge deck. In an attempt to avoid expensive full-scale crash testing, components of the existing system were evaluated using worst case conditions on two dynamic bogie crash tests and a series of computer simulations using nonlinear finite-element analysis. Simulation results closely approximated the physical results, with both displaying similar deformation, damage, and force levels. Both testing and simulation demonstrated that the barrier should function sufficiently if used on the FRP deck system. Further, the development …

Regional Mechanical Properties And Stress Analysis Of The Human Anterior Lens Capsule, Ryan M. Pedrigi, G. David, J. Dziezyc, J. D. Humphrey

Department of Mechanical and Materials Engineering: Faculty Publications

The lens capsule of the eye functions, in part, as a deformable support through which the ciliary body applies tractions that can alter lens curvature and corresponding refractive power during the process of accommodation. Although it has long been recognized that characterization of the mechanical properties of the lens capsule is fundamental to understanding this physiologic process as well as clinical interventions, prior data have been limited by one-dimensional testing of excised specimens despite the existence of multiaxial loading in vivo. In this paper, we employ a novel experimental approach to study in situ the regional, multiaxial mechanical behavior of …

A Scientific Foundation Of Collaborative Engineering, S. C.-Y. Lu, W. Elmaraghy, G. Schuh, R. Wilhelm

Department of Mechanical and Materials Engineering: Faculty Publications

Collaborative engineering is the practical application of collaboration sciences to the engineering domain. In today’s highly connected technology-driven economy, the production industry must rely on the best practices of collaborative engineering to stay competitive when designing, manufacturing, and operating complex machines, processes, and systems on a global scale. Despite its importance, collaborative engineering is currently more of a practiced art than a scientific discipline. A better understanding of how engineers should collaborate with all stakeholders to accomplish complex tasks that fulfill our increasing social responsibilities is a grand challenge. However, because we currently lack well-defined sciences of human collaboration, we …

Single-Sided Crash Cushion System, John D. Reid, John R. Rohde, Dean L. Sicking

Department of Mechanical and Materials Engineering: Faculty Publications

A single-sided crash attenuation cushion system having an impact head and three stage energy absorption mechanism. The energy absorbing mechanism has a mandrel for deforming thin-walled tubes in a controlled collapse to absorb impact forces from a colliding vehicle. The third stage of the absorption mechanism includes an additional deformable compressible tube between the fixed-object hazard and the thin walled tubes.

End Splice Assembly For Box-Beam Guardrail And Terminal Systemis, John D. Reid, John R. Rohde, Dean L. Sicking, King K. Mak

Department of Mechanical and Materials Engineering: Faculty Publications

An end splice assembly for a box-beam guardrail and terminal system having a first stage rail element and a second stage rail element. The assembly has two major connecting components. Upper and lower bent plate channels and upper and lower channel splice plates. The channels and plates have side walls which extend laterally to one another when the two rail elements are mated. The channels and plates are fastened together to provide moment strength to the splice within the system.

Preparation Of High-Strength Nanometer Scale Twinned Coating And Foil, Xinghang Zhang, Amit Misra, Michael Nastasi, Richard G. Hoagland

Department of Mechanical and Materials Engineering: Faculty Publications

Very high strength single phase stainless steel coating has been prepared by magnetron sputtering onto a substrate. The coating has a unique microstructure of nanometer spaced twins that are parallel to each other and to the substrate surface. For cases where the coating and substrate do not bind strongly, the coating can be peeled off to provide foil.

Order And Disorder, Entropy In Math, Science, Nature And The Arts, Sol Neeman Ph.D., Arie Maharshak

Engineering Studies Faculty Publications and Creative Works

Often, science and engineering students have difficult time in viewing certain concepts in their holistic form. An example for such a concept is the concept of Entropy. Although it originated from the field of thermodynamics, the relation between order and disorder is a profound one and manifests itself in various fields, sometimes unrelated, such as math and science, nature and the arts. In the discipline of physics, the amount of disorder in a system has been quantified by the concept of Entropy. In the area of information theory it provides a quantitative measure of the amount of compression that may …

Statistical Interpretation Of Mohr-Coulomb Theory As Applied To Fracture In Brittle Materials Containing Cracks, Mudit J. Monsi

Mechanical & Aerospace Engineering Theses & Dissertations

Fracture in brittle materials containing pre-existing cracks was studied. The probability of of crack growth under both shear and tensile stresses was determined for an arbitrary distribution of crack sizes. Two different crack orientation distributions, random and uniform, as well as friction were also taken into account. The material's reliability was assumed to depend on the number of active cracks at a particular stress level, and this was expressed as an arbitrary 2-parameter Weibull distribution. Two new and efficient methods for calculating crack growth probabilities based on spherical triangles and spherical caps were developed. They utilized normalized stress coordinates and …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

College Of Engineering Senior Design Competition Spring 2006, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Modeling And Representation Of Geometric Tolerances Information In Integrated Measurement Processes, Xiaoping Zhao, T. M. Kethara Pasupathy, Robert G. Wilhelm

Department of Mechanical and Materials Engineering: Faculty Publications

Modeling and representation of geometric tolerances information across an enterprise is viable due to the advances in Internet technologies and increasing integration requirements from industry. In Integrated Measurement Processes (IMP), geometric tolerances data model must support different models from several well-defined standards: including ASME Y14.5M-1994, STEP, DMIS, and others. In this paper, we propose a layered conformance level geometric tolerances representation model. This model uses the widely applied ASME Y14.5M-1994 as its foundation layer by abstracting most information from this standard. The additional geometric tolerances information defined by DMIS and STEP is incorporated into this model to form corresponding conformance …

Experimental And Finite Element Analysis Of Preloaded Bolted Joints Under Impact Loading, Brendan O'Toole, Kumarswamy Karpanan, Masoud Feghhi

Mechanical Engineering Faculty Research

One of the primary parameters in analyzing bolted joints is preload in the bolt. We have considered several possible preload modeling techniques to analyze the effect of preload on the dynamic response of the bolted joints. Five different methods of applying preload in the nonlinear finite element analysis are evaluated. These methods are “force on bolt and nut”, “force on bolt shank”, “interference fit”, “thermal gradient” and “initial stress method”. Explicit and implicit analyses are used for transient response and preload generation in bolt respectively. Time history and shock response spectrum are used to compare experimental and simulation results. Simulation …

Energy Efficient Process Heating: Managing Air Flow, Kevin Carpenter, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Much energy is lost through excess air flow in and out of process heating equipment. Energy saving opportunities from managing air flow include minimizing combustion air, preheating combustion air, minimizing ventilation air, and reconfiguring openings to reduce leakage.

This paper identifies these opportunities and presents methods to quantify potential energy savings from implementing these energy-savings measures. Case study examples are used to demonstrate the methods and the potential energy savings.The method for calculating savings from minimizing combustion air accounts for improvement in efficiency from increased combustion temperature and decreased combustion gas mass flow rate.

The method for calculating savings from …