Engineering Science and Materials Commons^™

Mesoscale Modeling And Machine Learning Studies Of Grain Boundary Segregation In Metallic Alloys, Malek Alkayyali

All Dissertations

Nearly all structural and functional materials are polycrystalline alloys; they are composed of differently oriented crystalline grains that are joined at internal interfaces termed grain boundaries (GBs). It is well accepted that GB dynamics play a critical role in many phenomena during materials processing or under operating environments. Of particular interest are GB migration and grain growth processes, as they influence many crystal-size dependent properties, such as mechanical strength and electrical conductivity.

In metallic alloys, GBs offer a plethora of preferential atomic sites for alloying elements to occupy. Indeed, recent experimental studies employing in-situ microscopy revealed strong GB solute segregation …

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

High-Yield Bioinspired Atmospheric Water Capture Through Hydrogels, Yiwei Gao

UNLV Theses, Dissertations, Professional Papers, and Capstones

Water scarcity is a global issue affecting billions of people, and atmospheric water harvesting (AWH) technology has been identified as a potential solution. However, existing single-material AWH approaches have limited water harvesting yields due to alternated water capture, storage, and release stages, and only function within a high relative humidity range. In my doctoral research project, we developed a bio-inspired, hydrogel-based multi-layer AWH approach that allows for segregated capture, storage, and release stages, and is envisioned to have higher daily water harvesting efficiency even in low-humidity areas. My research began with understanding the relations between hydrogel mechanical stiffness, hydraulic permeability, …

Spectroscopic Studies On Silicon And Chalcopyrite Materials For Solar Energy Applications, Amandee Hua

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this dissertation, silicon-based materials for photovoltaics and chalcopyrite-based materials for photoelectrochemical water splitting are investigated using various spectroscopic and microscopic techniques. Although silicon dominates the photovoltaic market, further improvement can be made by using an alternative low temperature passivation approach. Currently, thermally grown SiO2 passivation is commonly used for silicon solar cells. However, this technique requires high processing temperatures (>800 °C), which increases the thermal budget, potentially decreases the bulk quality of Si, and can lead to difficulties in implementing in production lines. Here, a S-based passivation approach is studied that require lower processing temperatures of ~550 °C. …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Metastability And Degradation In Cu(In,Ga)Se2 Thin-Film Solar Cells, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cu(In,Ga)(S,Se)2 or CIGS is a thin-film semiconductor that has shown a device efficiency of 23.35% and 24.2% for single-junction and perovskite/CIGS tandem solar cells, respectively. CIGS offers promising properties such as tunable bandgap and ease of processing making them great candidates for thin-film tandem devices. However, knowledge of the effect of material defects, buffer materials, and post-deposition treatment (PDT) on degradation and metastability behavior in these devices is not well understood.In this dissertation, metastability and long-term degradation of CIGS thin-film solar cells have been investigated under combinatorial stress factors of heat, light, and voltage bias to systematically understand the effect …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Preface To The Special Issue On Lithium-Sulfur Batteries, Jia-Jia Chen, Ren-Jie Chen, Zhong Jin

Journal of Electrochemistry

No abstract provided.

Cobalt/Carbon Composites As Sulfur Hosts For High-Performance Lithium-Sulfur Batteries, Yun-Rui Yang, Huan-Huan Dong, Zhi-Qiang Hao, Xiang-Xi He, Zhuo Yang, Lin Li, Shu-Lei Chou

Journal of Electrochemistry

Lithium-sulfur (Li-S) battery is one of the promising energy storage devices because of its high energy density. However, the sulfur cathode suffers from sluggish electrochemical reaction kinetics, slow charge transfer, large volume expansion and severe shuttle effect of lithium polysulfides inevitably resulting in low reversible capacity, poor rate performance and short cycle life, limiting its practical applications. Herein, the recent progress of cobalt/carbon composites, including cobalt nanoparticles and cobalt single atoms, as the sulfur host materials in Li-S batteries is overviewed. In general, cobalt plays the role of electrocatalyst, which inhibits the shuttle effect of lithium polysulfides, accelerates the electrochemical …

Recent Advances Of Functional Electrolyte Additives For Lithium-Sulfur Batteries, Xiu-Qing Zhang, Shuai Tang, Yong-Zhu Fu

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries have become one of the most promising next-generation battery systems due to their high energy density and low cost. However, the application of Li-S batteries still faces critical challenges, such as the low conductivities of S and Li₂S, shuttle effect of polysulfides and dendrite growth of Li, etc. The optimization of the electrolyte can ameliorate the electrolyte|electrode interphase, conveniently regulating the parasitic reaction and improving the performance of the resultant batteries. The functional additives in electrolytes provide chances to tune the interphase and even the redox mechanism to improve the performance of the batteries. In …

Metals And Alloys As Catalytic Hosts Of Sulfur Cathode For Lithium-Sulfur Batteries, Zhen-Yu Wang, Xue-Ping Gao

Journal of Electrochemistry

Lithium-sulfur batteries are recognized as one of the most promising next-generation energy storage devices, owing to the high theoretical energy density of 2600 Wh·kg^–1. However, their application has been seriously hindered by the sluggish electrochemical reaction kinetics of elemental sulfur and discharged products (Li₂S₂/Li₂S), and the notorious “shuttle effect” of soluble intermediate lithium polysulfide species, leading to poor cycle stability, low sulfur utilization and inferior coulombic efficiency. Introducing catalytic hosts into sulfur cathode is an efficient path to propel the conversion of sulfur-contained species, thus preventing the dissolution and loss of active-sulfur …

Ultraviolet-Initiated In-Situ Cross-Linking Of Multifunctional Binder Backbones Enables Robust Lithium-Sulfur Batteries, Sha Li, Xiao Zhan, Gu-Lian Wang, Hui-Qun Wang, Wei-Ming Xiong, Li Zhang

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries show attractive prospects owing to their high theoretical energy density, but their commercialization still faces such challenges as lithium polysulfides shuttling, severe volume change and considerable polarization. These stubborn issues place higher demands on each component in the battery, such as the development of multifunctional binders with superior mechanical properties. Herein, ethoxylated trimethylolpropane triacrylate was firstly introduced into sulfur cathodes, and in-situ cross-linked by ultraviolet (UV) curing combined with traditional polyvinylidene difluoride binder (i.e., forming a binary binder, denoted as c-ETPTA/PVDF) to construct high-loading and durable Li-S batteries. The covalently cross-linked ETPTA framework not only significantly enhances …

Shape Memory Polymer-Based Multifunctional Syntactic Foams, Siavash Sarrafan

LSU Doctoral Dissertations

With the increase in popularity of shape memory polymers (SMPs), especially in applications such as aerospace, textile, biomedical engineering, and even structures, the weight of the material and the devices made with it has always been a crucial factor. Using the shape memory polymer as a matrix to make a syntactic foam is one of the best and most affordable approaches to creating a lighter material that still has the shape memory effect. The addition of particles of different stiffness, strength, and size, with variable fractions, creates a composite that enables engineering the mechanical, as well as other physical and …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Development Of Novel Electrodes And Electrolytes For Safer Aqueous Ammonium Ion Batteries With Enhanced Performance., Shelton Farai Kuchena

LSU Doctoral Dissertations

The Lithium-ion battery (LIBs) system has dominated the battery market because of its superior energy and power density. Problems related to LIBs such as safety, scarcity of cobalt and lithium have led researchers to explore alternative battery systems. NH₄⁺ ion is a nonmetal charge carrier with lower molar mass (18 mol g^-1) and smaller hydrated ionic size (3.31 Å) which results in excellent electrochemical properties. Furthermore, NH₄⁺ ion has a tetrahedral structure that has no preferred orientation as compared to spherical metal ions giving a different intercalation chemistry based on hydrogen bonding. These properties …

Beirut Arab University - Faculty Of Engineering - Newsletter Issue 0, Faculty Of Engineering, Beirut Arab University

Engineering Newsletters

No abstract provided.

A Review On Solid-State Li-S Battery: From The Conversion Mechanism Of Sulfur To Engineering Design, Huan-Huan Jia, Chen-Ji Hu, Yi-Xiao Zhang, Li-Wei Chen

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries attract sustained attention because of their ultrahigh theoretical energy density of 2567 Wh·kg^–1 and the actual value over 600 Wh·kg^–1. Solid-state Li-S batteries (SSLSBs) emerge in the recent two decades because of the enhanced safety when compared to the liquid system. As for the SSLSBs, except for the difference in the conversion mechanism induced by the cathode materials themselves, the physical-chemical property of solid electrolytes (SEs) also significantly affects their electrochemical behaviors. On account of various reported Li-S batteries, the advantages and disadvantages in performance and the failure mechanism are discussed in this review. …

Recent Research Progresses Of Solid-State Lithium-Sulfur Batteries, Yu Luo, Ru-Qin Ma, Zheng-Liang Gong, Yong Yang

Journal of Electrochemistry

All solid-state lithium-sulfur batteries (ASSLSBs) are considered to be one of the most promising next-generation energy storage systems, due to the promises of high energy density and safety. Although the use of solid-state electrolytes could effectively suppress the "shuttle effect" and self-discharge of the conventional liquid lithium-sulfur (Li-S) battery, the commercialization of ASSLSBs has been seriously hampered by the electrolyte degradation, electrode/electrolyte interfacial deterioration, electrochemo-mechanical failure, lithium dendrite growth and electrode pulverization, etc. This paper provides a comprehensive review of recent research progresses on the solid-state electrolytes, sulfur-containing composite cathodes, lithium metal and lithium alloy anodes, and electrode/electrolyte interfaces in …

Bimetallic Compound Catalysts With Multiple Active Centers For Accelerated Polysulfide Conversion In Li-S Batteries, Wu-Xing Hua, Jing-Yi Xia, Zhong-Hao Hu, Huan Li, Wei Lv, Quan-Hong Yang

Journal of Electrochemistry

Practical applications of lithium-sulfur (Li-S) batteries are hindered mainly by the low sulfur utilization and severe capacity fading derived from the polysulfide shuttling. Catalysis is an effective remedy to those problems by promoting the conversion of polysulfides to reduce their accumulation in the electrolyte, which needs the catalyst to have efficient adsorption ability to soluble polysulfides and high activity for their conversion. In this work, we have proposed a bimetallic compound of NiCo₂S₄ anchored onto sulfur-doped graphene (NCS@SG) to fabricate a catalytic interlayer for Li-S batteries. Compared to CoS, the NiCo₂S₄ demonstrated much higher …

Coni-Based Bimetal-Organic Framework Derived Carbon Composites Multifunctionally Modified Separators For Lithium-Sulfur Batteries, Yan-Jie Wang, Hong-Yu Cheng, Ji-Yue Hou, Wen-Hao Yang, Rong-Wei Huang, Zhi-Cong Ni, Zi-Yi Zhu, Ying Wang, Ke-Yi Wei, Yi-Yong Zhang, Xue Li

Journal of Electrochemistry

The commercial application of lithium-sulfur batteries (LSB) is still limited by the irreversible capacity fading caused by the shuttle of lithium polysulfides (LIPS). To address this issue, a bimetal (nickel, cobalt)-organic framework (MOF) derived carbon, (Ni, Co)/C, was prepared to modify the separator. The multifunctionally modified separator effectively captures LIPS, ensuring the stability and reversibility of sulfur fixation, while providing catalytic activity and improving ionic conductivity. The cobalt metal has a larger coordination number, more pore structure distribution, larger specific surface area, more surface C=O, and smaller particle size to achieve a large and rapid chemical sulfur fixation. The high …

Preface To The Special Issue On Lithium-Sulfur Batteries, Jia-Jia Chen, Ren-Jie Chen, Zhong Jin

Journal of Electrochemistry

No abstract provided.

Physics-Based Crystal Plasticity Model For Predicting Microstructure Evolution And Dislocation Densities, Juyoung Jeong

LSU Doctoral Dissertations

This work presents three different studies investigating plastic deformation mechanisms in metals and alloys using crystal plasticity finite element (CPFE) modeling. The first study presents a new nonlocal crystal plasticity model for face-centered cubic single crystals under heterogeneous inelastic deformation. The model incorporates generalized constitutive relations that incorporate the thermally activated and drag mechanisms to cover different kinetics of viscoplastic flow in metals and describes the plastic flow and yielding of single-crystals using dislocation densities. The model is compared to micropillar compression experiments for copper single crystals and clarifies the complex microstructural evolution of dislocation densities in metals. The second …

Oh, My Darling Clementine: A Detailed History And Data Repository Of The Los Alamos Plutonium Fast Reactor, Hannah K. Patenaude, Franz J. Freibert

College of Sciences Graduate Student Research

The Los Alamos Plutonium Fast Reactor, Clementine, provided the first fast neutron spectrum using a metallic plutonium fuel system and liquid mercury coolant. Clementine is often mentioned in the history of fast, metal-fueled, or metal-cooled designs, with little public information regarding the specifications or timeline. This paper contains a synopsis of each report regarding the development, operation, experimental results, failures, and subsequent disassembly of Clementine to explore this unique reactor within the context of modern advanced reactor development.

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Advances And Challenges On Cathode Catalysts For Lithium-Oxygen Batteries, Bo Wen, Zhuo Zhu, Fu-Jun Li

Journal of Electrochemistry

Aprotic lithium-oxygen batteries (LOBs) with high theoretical energy density have received considerable attention over the past years. However, the oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) at cathodes suffer from slow kinetics for large overvoltages in LOBs. Significant advances on catalysts have been achieved to accelerate cathode kinetics, but understanding on the formation/decomposition processes of Li₂O₂ is limited. Herein, this review highlights the fundamental understanding of the correlation between catalysts and formation/decomposition of Li₂O₂. Various types of cathode catalysts are discussed to reveal the mechanism of formation/decomposition of Li₂O₂, …

Recent Advances In Anode Materials Of Solid Oxide Electrolysis Cells, Geng Zou, Wei-Cheng Feng, Yue-Feng Song, Guo-Xiong Wang

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) as an electrochemical energy conversion device has attracted increasing attention due to its large current density, high Faradaic efficiency and energy efficiency. Oxygen evolution reaction at the anode, a four-electron transfer process, is an important half-reaction for SOEC, which contributes to the main polarization resistance and consumes most electric energy during the electrolysis process. Hence, designing anode materials with high activity and stability is crucial for the performance improvement and practical application of SOEC. Recently, some advances have been made in the development of high-performance anode. In the current review, the mechanisms for CO_{2 …}

Anodic Electrocatalysis Of Glycerol Oxidation For Hybrid Alkali/Acid Electrolytic Hydrogen Generation, Xin Feng, Bo-Wen Liu, Ke-Xin Guo, Lin-Feng Fan, Gen-Xiang Wang, Su-Qin Ci, Zhen-Hai Wen

Journal of Electrochemistry

Electrolytic hydrogen production is heavily restricted by high-energy consumption majorly due to the relatively high potential of anodic oxygen evolution reaction (OER). Development of OER-alternative reaction at the anode has been recently proposed as a promising pathway to address the associated issues. In this work, we report a hybrid acid/alkali dual-electrolyte electrolyzer by coupling acidic hydrogen evolution reaction (HER) using commercial Pt/C cathode with alkaline Electrocatalytic glycerol oxidation (GOR) which is implemented by developing a nickel foam (NF) supporting Co₃O₄ nanosheets anode that shows low overpotential and high selectivity toward GOR for formate production. The hybrid acid/alkali …

Preface To Special Issue On Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Highly Dispersed Pt Nanoparticles Root In Single-Atom Fe Sites In Ldhs Toward Efficient Methanol Oxidation, Qing-Cheng Meng, Lin-Bo Jin, Meng-Ze Ma, Xue-Qing Gao, Ai-Bing Chen, Dao-Jin Zhou, Xiao-Ming Sun

Journal of Electrochemistry

Active and durable electrocatalysts for methanol oxidation reaction are of critical importance to the commercial viability of direct methanol fuel cell, which has already attracted growing popularities. However, current methanol oxidation electrocatalysts fall far short of expectations and suffer from excessive use of noble metal, mediocre activity, and rapid decay. Here we report the Pt anchored on NiFe-LDHs surface hybrid for stable methanol oxidation in alkaline media. Based on the high intrinsic methanol oxidation activity of Pt nanoparticles, the substrates NiFe-LDHs further enhanced anti-poisoning ability and maintained unaffected stability after 200,000 s cycle test compared to commercial Pt/C catalyst. The …