Engineering Science and Materials Commons^™

The Reduction Of Oxygen To Hydrogen Peroxide At The Poly(O-Phenylenediamine)-Filmed Electrode, Zhaoe Lu, Tiangeng Zhong, Guanyong Zhang

Journal of Electrochemistry

The poly(o-phenylenediamine) (PPD) filmed graphite electrode was formed by electro-polymerization of o-phenylenediamine in acidified (pH=1) 0.2 mol·L^-1 Na₂SO₄ solution using the cyclic voltammetric methed. The catalytic effect of the electrcareduction of oxygen in acid olution was demonstrated by the voltammogram of the electrode in the oxygen saturated acid solutionof Na₂SO₄. The current efficiency of the reduction of oxygen to hydrogen peroxide was determined by the electrolysis in a divided cell under the condition of constant current. The various effectsinfluencing the accmulation of H₂O₂ in the catholyte were discussed.

Studies On Coordination Behavior Of Dimethyl Sulfoxide In Complex Of Rare Earth With Cryptand, Shichang Liu, Tianpei Zhu

Journal of Electrochemistry

Electrochemical reduction reaction in the course of the titration of Eu(2.2.2) and Eu(2.2) using strong bonding solvent, DMSO, in C₂H₄Cl₂ has been investigated by cyclic voltammetry. The greater the concentration of strong bonding solvent, the more negative the half-wave potentials for the reduction reaction are. The coordination number of Eu(2.2.2) and Eu(2.2) which are 2 and 3 respectively, with DMSO can be calculated, according to the relations between half-wave potentials and the variety of concentration of DMSO.

An Investigation Of Hole Size Effects In A Composite Material During Tensile Fracture, David Floyd Moore

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental investigation was conducted to evaluate the hole size effects, i.e., the reduction in strength with an increase in hole size at a constant stress concentration factor, for a glass fiber reinforced epoxy crossply laminate during tensile fracture. The characteristic dimension according to the point-stress and average-stress criteria of the two-parameter models proposed by Whitney and Nuismer were determined and compared for a circular hole, optimized circular hole, square hole with radiused corners and square hole with sharp corners. Modified versions of the two-parameter models proposed by Karlak and Pipes, Wetherhold, and Gillespie were also compared. On the basis …

Studies Of Elecctrochcmical Oscillation Of Au/Hcl In Presence Of ″Positive Feedback″Of Substrate Electrodes, Bin Ren, Bingwei Mao, Xiongwei Cai, Tao Jiang, Jiqian Mu

Journal of Electrochemistry

/

A Photoelectrochemical Investigation Of Zirconium Oxide Film, Maizhi Yang, Ping Wei, Di Quarto F., Piazza S., Sunseri C.

Journal of Electrochemistry

A photoelectrochemical investigation has been carried out on zirconium initialoxide film and its oxide film grownanodically at constant rate up to different thickness. Both anodicand cathedic photocurrents on the photocurrent spectrum depended on the potential, but had littlerelation with the forming anedic films or measuring solutions. Photocurrent spectrum and photocurrenttransients suggested that the oxide films on zirconium were duplex layers structure. The internal layerwas ZrO₂ and the external layer ZrO₂·(H₂O)_n. The photocurrent included photogenerated carrier ininternal and external oxide films, as well as internal photoinjection process for electrons from thesubstrate metal into the …

Application Of Inhibitor To Improve The Anticorrosion Performance Of Electrophoretic Coating, Changshou Cai, Fangteng Su, Bihuan Liu, Guomou Wen, Jingdong Guo, Renxin Liu, Weidong Tian

Journal of Electrochemistry

To improve the anti-corrosion performance of electrocoating, organic andinorganic inhibitors are applied in an anodic electrophoretic-coating. The results show that the deposition of polymer with zinc phospate exhibits a high inbihition efficiency. The inhibition mechanism of the inhibitor in electrocoating has been studied.

A Investigation Of Hydrogen-Storage Alloy As Catalytic Electrode For Hydrogenation Of Nitrobenzene, Shigang Lu, Hanxi Yang, Changfa Wan

Journal of Electrochemistry

Since hydrogen-storage alloy ean not only absorb hydrogen atoms to form highlyreactive metal hydride as hydrogen source by electrolysis but also possesses a certain catalytic activityfor hydrogenation,it is thus feasible to utilize the allov as a novel electrode for electrolvtichydrogenation in organic electroreduction. This work employed misch metal AB₅ type alloy as acatalytic electrode and studied the electrochemical hydrogenation of nitrobenzene.

The hydrogen-storage electrode (MH) was a plastic bonded electrode sheet made from a paste of Mm(NiCoMnAl)₅ alloy powder and teflon emulsion. The electrolysis was performed at constantcurrent and controlled potential in a three electrode cell of H-type …

Transient Photocurrent Behavior Of Multiple Quantum Well Gaas/AlXGa(1-X)As Electrode, Liu Yao, Xurui Xiao, Yuan Lin, Yiping Zeng, Dianzhao Sun, Haiqun Zheng

Journal of Electrochemistry

Transient photocurrents induced by short light pulses at lattice-matched multiplequantum well (MQW)GaAs/Al_0.3)Ga_0.7 As electrodes were studied in the 1 ×10^-2 mol·dm^-3 ferrocene([Fc⁰]/[Fc⁺]=9/1)-0.1 mol·dm^-3 tetrabutylammonium tetrafluoroborate acetonitrile solutionin order to examine the relaxation photoprocesses and to evaluate kinetic parameters of superlattice electrodes.

GaAs/Al_0.3Ca_0.7 As MQW electrode consisting of 10 periods with each of GaAs well (5.3 nm) and Al_0.3Ga_0.7. As barrier (10 nm) showed two pronounced and well-resolved peak structures located at 1.503 eV and 1.699 eV in the photocurrent spectrum, corresponding to the …

Synthesis Of LiXCoo2 And Its Behaviour In Rechargeable Lithium Battery, Mingfeng Guo, Ruimin Yang, Zebo Zhang, Jincao Ye

Journal of Electrochemistry

The Variations of crystal lattice parameters of Li_xCoO₂ during charge anddischarge have been st ud ied by XRD and AAR spectroscopy. It was found that the Li_xCoO₂ crystalvolume expanded during charge and contracted during discharge. The crystal lattice structure was broken because of the formation of Co₃O₄ when deeply charge.The variation of lattice parameter C₀ value in cycling process was similar to that in charge process.The variation of 006 peak was the mostsensitive in every case. In case of preheating for 20 hours at 700℃ before operating high temperature, the …

The Effect Of Some Ions On Cr2O72- Anodic Formation Process At Pt And Pbo2 Electrodes, Shixiong Jin, Zhigang Zhou, Lan Wang

Journal of Electrochemistry

The influence of Ag₂SO₄, Li₂SO₄, Na₂SO₄, K₂SO₄, (NH₄)₂SO₄,MgSO₄ and KF on the evolution of O₂ and the formation of Cr₂O at Pt and PbO₂ anodes was investigated in mixed H₂SO₄-Cr₂(SO₂)₃ solutions. The kinetic data related respectively to Cr₂O formation and O₂ evolution at Pt and PbO₂ anodes were measured by method of resolving the steady-state polarization curve. The Tafel slope …

Self Assembly Via Layer By Layer Surface Reaction On Gold Electrodes And The Electrochcmical Characterization, Xiandui Dong, Juntao Lu, Chuanxin Cha

Journal of Electrochemistry

The self-assembled monolayers,which were built by spontaneous adsorption of ω-carboxylic acid thiols on gold surface,were used as substrate for further modification through later bylayer amide surface reactions. At each stage of modification,the gold surface was characterizedelectochemieally. The results demonstrated that the strategies of layer by layer self assembly is ofsignificant potential for fabrieating functionalized ultrathin layers.

Electroreduction Of The Nittobenzene On Titanium Electrode Implanted With Palladium, Zhongda Wu, Xianjun Zhu, Hongsen Wang

Journal of Electrochemistry

The titanium substrates were bombarded with 1×10¹⁷～5×10¹⁷ ions·cm^-2 ofpalladium at the room temperature. The surface composition of implanted electrode and concentration-depth profiles of various elements were measured by AES. The electrored uction processes ofnitrobenzene (NB) in 0.1 mol/L NaOH solution at Pd/Ti electrodes have been investigated by cyclicvoltaivimetry. The results show that the palladium implanted titanium electrodes exhibit a high catalyticactivity in the electroreduction of NB. The NB radical anion, which is the product of one-electronelectroreduction of NB, was detected by ESR in-situ in conjunction with electrochemical methods. Aniline was also detected as a product of …

Electroreduction Of Holmium Ion On Iron Electrde In Molten Cholorides, Qiqin Yang, Guankun Liu, Yuzhi Su

Journal of Electrochemistry

The cyclic voltammetry, open circuit potential-time curve after poteritiostatic electrolysis, current-time curve at potential step, X-ray diffraction and electron probe microanalysiswere used to investigate the electrode process of Ho(Ⅲ) reduced on iron electrode in molten chloridesand the phases of surface alloy layer. The Ho-Fe alloys are formed at first, and then the metallic holmium is deposited when Ho(Ⅲ) is reduced on iron electrode. The charge transfer is reversible. The free energies of formation for the four inter metallic compounds of Ho-Fe system, the diffusion coefficients and diffusion activation energy of Ho in alloyed cathode are determined.

Electrocatalytic Oxidation Of Formaidehyde And Formic Acid On A Pt/SbAd Electrode, Hong Li, Lincai Jiang, Xiong Jiang

Journal of Electrochemistry

The electrocatalytic activity for the oxidation of formaldehyde and formic acid ona Sb-modified platinum (Pt/Sb_ad) was investigated. Results showed that the Pt/Sb_ad electrode was electrocatalytically more active than a Pt electrode in the anodic oxidation of formaldehyde and formicacid. In the case of formaldehyde, an oxidation peak appeared at a potential of ca. 0.7V. During the oxidation of formic acid, a 4-fold increase in the 1st peak current was observed. The Sb-modified platinum electrode was found to be most electrocatalytically active at a coverage of 0.75±0.05. The electrocatalytic activity of the Pt/Sb_ad electrode can be best …

The Study Of The Growth Processes Of The Oxides On Lead Electrodes In Sulfuric Acid Solution, Hesheng Zhai, Xuguang Chen, Jinkua You, Yong Yang, Zugeng Lin

Journal of Electrochemistry

The growth processes of PbO and PbO₂ on lead electrodes have been investigatedby using in-situ methods that are combined with temporary AC resistance measurment technique and in-situ laser scanning photoelectrochemical microscopy. It is found that a linear relationship existsbetween the electrode resistance(R) and^1/2 after the electrode is oxidized at +0.6 V(vs.Hg/H₂SO₄/35% H₂SO₄) for more than 5 min. This result suggests that the growth of PbO is well distributed during the early stage of oxidation. The study by using laser scanning photoelectrochemical microscopy has further proved this point. The results also …

The Electrode Process Of Y(Ⅲ) On Copper Electrode And Its Surface Metallizing, Chungen Zhou, Shuzhen Duan

Journal of Electrochemistry

The reduction of yttrium ion on copper electrode in NaCl-KCl-YCl₃ molten saltshas been investigated. The results indicate that the formation of intermetallic compounds is occuredbefore the metallic yttrium to be formed. The formation of intermetallic compounds is controlled bythe process of which yttrium atoms are diffusing into copper electrode. The kinetic characters todiffusion of yttrium atoms were also discussed.

The Catalytic Behavior For Ni-W Electrode Modified By Carbon Ion Beam Implantion, Jishuang Zhang, Yaojiao Lv, Qinglian Li, Baoen Shen

Journal of Electrochemistry

The hydrogen evolution activity in acidic and basic mediums for Ni-W electrodemodified by carbon ion bean implantation was investigated. The experimental results show thiselectrode has superior catalytic activity for the hydrogen evolution reaction than that of the unmodified Ni-electrode. Long period testing of electrolysis under high current density show that this electrode hasalonger useful life hence it is a practical electrode material. The temperature effect of electrocatalytic property was also inverstigated. The experimental regularities are explained on the basis of the formation of surface multialloys of Ni-W-WC.

Development Of Nial-Based Intermetallic Alloys: Effect Of Chromium Addition, R. Tiwari, Surendra N. Tewari, R. Asthana, A. Garg

Chemical & Biomedical Engineering Faculty Publications

The mechanical behavior of dual-phase NiAl(Cr) microstructures, consisting of elongated primary NiAl grains aligned with an intergranular NiAl-Cr eutectic phase, produced by extrusion of a cast NiAl(Cr) alloy, has been examined. Chromium addition to create a dual phase NiAl-based aligned microstructure leads to large increases in the yield strength but no significant toughness improvement. This is achieved primarily by solid solution hardening and precipitation hardening. The constitutional hardening rate resulting from deviations from stoichiometry in the nickel-rich NiAl was estimated to be about 66 MPa per atomic per cent of nickel.

Nonlinear Finite Element Micromechanic Analysis Of Thermoplastic Composite Of Recycled High Density Polyethylene Reinforced With Short Glass Fibers, Qiming Lou

Masters Theses

This thesis studied the nonlinear micromechanic behavior of thermoplastic composite of recycled high density polyethylene (HDPE) reinforced with short glass fibers using finite element method. The composite material was modeled using a micromechanic unit cell to simulate the stress distribution between the plastic matrix and the fiber in the composite. Nonlinear behavior of recycled HDPE and imperfect bonding between the fiber and matrix were investigated. Load-bearing capability of the fiber was evaluated using stress partition ratio (SPR) in the composite models. The effect of fiber aspect ratio on the stress distribution of the composite was studied to optimize the material …

Investigation Into The Behavior Of Geometrically Nonlinear Composite Arches, John C. Bailey

Theses and Dissertations

This research modifies the existing finite element formulation of a potential energy based large deformation and moderate rotation theory. Hermitian shape functions replace the existing linear bending angle interpolations. Negligible differences between the two formulations indicate the underlying kinematics limit the accuracy, not the finite element interpolations. Using the new program, numerous nonlinear arch geometries are modeled to investigate the effects of arc length and thickness variations. Local and global snapping phenomena are captured as well as through the thickness shear driven nonlinearities.

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner

Theses and Dissertations

This study investigated the fatigue behavior and damage mechanisms of a [0-90]_4s SiC-MAS ceramic matrix composite under tension-tension loading at two elevated temperatures and two frequencies. Stress and strain hystereses, maximum and minimum strain, and modulus of elasticity were evaluated to characterize the material behavior. Microscopy and fractography were used to evaluate damage progression and mechanisms. Fatigue life was independent of frequency at both temperatures.

Characterization Of Fatigue Behavior Of 2-D Woven Fabric Reinforced Ceramic Matrix Composite At Elevated Temperature, Daniel J. Groner

Theses and Dissertations

This study investigated the fatigue behavior and associated damage mechanisms in notched and unnotched enhanced Sic-SiC ceramic matrix composite specimens at 1100°C. Stiffness degradation, strain variation, and hysteresis were evaluated to characterize material behavior. Microscopic examination was performed to characterize damage mechanisms. During high cycle-low stress fatigue tests, far less fiber-matrix interface debond was evident than in low cycle-high stress fatigue tests. Notched specimens exhibited minimal stress concentration during monotonic tensile testing and minimal notch sensitivity during fatigue testing. Damage mechanisms were also similar to unnotched.

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite Subjected To Tension-Tension Cycling With Hold Time, Scott A. Grant

Theses and Dissertations

This study was carried out to investigate the elevated temperature behavior of the SiC-MAS5 cross- ply [0-90]_4S ceramic matrix composite manufactured by Corning Inc. to fatigue with loading waveforms that combine the characteristics of stress rupture and high cycle fatigue. The test results were compiled in the form of S-N (cycles to failure), S-T (exposure time versus cycles to failure), S-S (energy exposure versus cycles to failure), normalized modulus degradation, strain progression, and hysteresis loop progression. From the mechanical behavior demonstrated by these curves, relationships between the effect of the environment and loading waveform were developed. In addition, a …

An Experimental And Analytical Investigation Of The Iosipescu Shear Test For Composite Materials, Barry Stuart Spigel

Mechanical & Aerospace Engineering Theses & Dissertations

Mechanical properties of composite materials under shear loading are difficult to determine. The Iosipescu Shear test, originally proposed for metals, has in recent years been applied to composites. It has the advantages of small specimen size, simple loading and a reasonably uniform shear stress in the test section.

The purpose of this work is to study the validity of the Iosipescu test method for measuring the shear modulus and shear strength of composites. Finite element analyses indicate that optimum specimen geometry and load locations depend upon the degree of orthotropy of the composite. Test results for a quasi-isotropic graphite/epoxy laminate …

Stress Fields In Composites With A Variable Interphase Under Thermo-Mechanical Loadings, Nianfeng Chen

Mechanical & Aerospace Engineering Theses & Dissertations

An interphase in a composite material has a important role for the composite performance. It influences directly or indirectly the strength, fatigue performance and effective properties of the composite. Recently, interphase has drawn increasing attention in composite mechanics. To the best of our knowledge, however, no one seems to have considered the effect of the variable material prope1ty in the interphase on the stress field in the composite material. In this research, the stress fields are determined in the continuous fiber composite and the particulate composite by using the four concentric circular cylinders model and the four phase spheres model, …

Investigation Of Tension-Compression Fatigue Behavior Of A Cross-Ply Metal Matrix Composite At Room And Elevated Temperatures, Elizabeth A. Boyum

Theses and Dissertations

This research, the first load-controlled tension-compression fatigue testing to be performed on a MMC, extends the existing knowledge of MMC fatigue damage mechanisms to include the tension compression loading condition. To accomplish this, a (0/90)2, SCS-6/Ti-15-3 laminate was subjected to tension- tension fatigue at room temperature, and tension-compression fatigue at both room temperature and 427°C. Stress and strain data was taken to evaluate the macro-mechanic behavior of the material. Microscopy and fractography were performed to characterize the damage on a micro-mechanic level. On a maximum applied stress basis, the room temperature tension-tension specimens had longer fatigue lives than the room …

Influence Of Embedded Optical Fibers On Compressive Strength Of Advanced Composites, Stefan B. Dosedel

Theses and Dissertations

This study investigated the effects of embedding optical fibers into advanced composite materials. This combination was meant to simulate 'smart structures' that have been shown to sense several different variables in the composite including strain, temperature, and damage. A laminate orientation taken from an existing aircraft structure was used to fabricate sixteen groups of specimens which were subjected to compression testing in an IITRI fixture to determine the ultimate compressive strength and modulus of elasticity. Ten of these groups were fabricated with optical fibers while the other six were control groups and contained no optical fibers. This study showed that …

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite Under Strain Controlled Tension-Tension And Tension-Compression Loading, James J. Gudaitis

Theses and Dissertations

This stuidy investigates the fatigue response of a cross-ply [0/90]_2s Nicalon/Calcium Aluminosillicate (Nicalcc/CAS) ceramic matrix composite at room temperature under strain controlled tension-tension and tension-compression fatigue loading. The primary objectives were to determine strain fatigue limits for both loading cases and to complete a fatigue life diagram (Δe-N) for all tests. Failure mechanisms were also studied. The average initial modulus value for this lay-up was 120 GPa. The ultimate tensile strain was 0.00988 mn/mm (285 MPa). Eight tests were conducted with maximum strains that ranged from 0.00300 mm/mm to 0.00722 mm/mm. The tension-tension fatigue limit was found to be …

Investigation Of Compressive Behavior For Metal Matrix Composites With A Circular Hole, Janet L. Gooder

Theses and Dissertations

This study investigated the notched and unnotched macromechanical response due to micromechanical behavior of [0/±45/90]_S SCS-6/β 21 S and [0/90] _2S Sigma/β 21S subjected to static compressive loads at room temperature. The stress-strain behavior and mechanical response in the presence of a circular hole was examined. A clear description of the progressive nature of damage, which ultimately resulted in failure, was provided. The effect of elevated temperature was shown for SCS-6/β 21S. The ultimate compressive strength and elastic modulus were reported for both MMCs. Sigma/β 21S and SCS-6/β 21S were mildly notch sensitive at room temperature. Notch sensitivity of …

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperatures Under Tension-Tension Loading, Richard J. Tuznik

Theses and Dissertations

A study was conducted which investigated the behavior of a Nicalon/ Calcium-Aluminosilicate (Nicalon/CAS) cross-ply [0/90]_2S ceramic matrix composite at elevated temperatures under tension-tension fatigue loading. Tension-tension fatigue tests were performed with a load ratio of R = 0.10 and a frequency of 10 Hertz at 700°C and 850°C. These results were compared to results from a previous study conducted at room temperature. Material behavior and damage was recorded by fatigue life curves, elastic modulus' maximum and minimum strain, acetate replication techniques, and post-mortem fractography. Analysis of these results showed identical matrix dominated damage behavior at RT and 700°C. Ultimate …