Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 1081 - 1110 of 3176

Full-Text Articles in Engineering Science and Materials

On The Mechanical Properties Of Al/Cu-Grid/Al Intermetallic Composite, Hamza Essoussi, Said Ettaqi Jan 2021

On The Mechanical Properties Of Al/Cu-Grid/Al Intermetallic Composite, Hamza Essoussi, Said Ettaqi

Journal of Metals, Materials and Minerals

The present paper deals with the experimental investigation of new process combining static compression with high temperature as a simple way to prepare new Al/Cu-grid/Al metallic composite (MC) that consists of Aluminum matrix and Copper grid acting as ductile reinforcement stacked between the Al sheets. At the stage of composite fabrication, two different thermal cycles were tested to highlight the effect of processing temperature on the layers’ adherence and the mechanical properties of the prepared composites. Consequently, the microstructural and mechanical results revealed that the compression at 630℃ for 30 min, then furnace cooled to 450℃ followed by air cooling …

Go to article

Thermal Behavior Of Solid Acids In The Rb3h(So4)2-Rbhso4 System Under Ambient Atmosphere, Chatr Panithipongwut Kowalski, Permpoon Chaijaroen, Farook Kaewniyom Jan 2021

Thermal Behavior Of Solid Acids In The Rb3h(So4)2-Rbhso4 System Under Ambient Atmosphere, Chatr Panithipongwut Kowalski, Permpoon Chaijaroen, Farook Kaewniyom

Journal of Metals, Materials and Minerals

The thermal behavior of solid acids in the Rb3H(SO4)2-RbHSO4 system under ambient atmosphere has been studied in comparison to the previously reported high-temperature behavior of the same system under humidified atmosphere. The findings showed that, under this level of humidity, the transition of RbHSO4, the transition of Rb5H3(SO4)4, and the disproportionation of Rb3H(SO4)2, occurred at the same temperatures as those under humidified atmosphere. However, the results from differential scanning calorimetry did not reveal the reaction temperature between Rb3H(SO4)2 and RbHSO4 due to the slow process. The dehydration temperatures of Rb5H3(SO4)4 were surprisingly similar between the systems under low and high …

Go to article

Graphene Enhanced Linear Low-Density Polyethylene Nanocomposites By Premixing And Melt Compounding, Wan Nazri Wan Busu, Ruey Shan Chen, Muhammad Jefri Mohd Yusof, Sahrim Ahmad Jan 2021

Graphene Enhanced Linear Low-Density Polyethylene Nanocomposites By Premixing And Melt Compounding, Wan Nazri Wan Busu, Ruey Shan Chen, Muhammad Jefri Mohd Yusof, Sahrim Ahmad

Journal of Metals, Materials and Minerals

In this study, linear low-density polyethylene/graphene nanoplatelets (LLDPE/GNPs) nanocomposites were prepared from conventional melt-mixing method and our new approach; two-step premix mixing technique. Indirect mixing technique (IDT) was employed to fabricate a premix of LLDPE/ GNPs in the ratio of 80:20 wt%. The effects of GNPs loadings and the processing method of nanocomposites on the mechanical strength, decomposition temperature, crystallinity, electrical impedance and morphology were investigated. Irrespective of processing methods, the prepared nanocomposites exhibited crystalline structure due to the presence of GNPs whilst the degradation temperature was recorded to be increased with GNPs loadings that signified improved thermal stability. The …

Go to article

Preparation Of Transparent Alumina Thin Films Deposited By Rf Magnetron Sputtering, Busarin Noikaew Noikaew, Laksana Wangmooklang, Saisamorn Niyomsoan, Siriporn Larpkiattaworn Jan 2021

Preparation Of Transparent Alumina Thin Films Deposited By Rf Magnetron Sputtering, Busarin Noikaew Noikaew, Laksana Wangmooklang, Saisamorn Niyomsoan, Siriporn Larpkiattaworn

Journal of Metals, Materials and Minerals

Alumina (Al2O3) thin films were prepared by RF magnetron sputtering technique using Al2O3 ceramic target. Effects of sputtering powers and oxygen gas mixtures were investigated and the optimized coating condition was applied on semi-precious gemstones. RF sputtering powers were varied to optimize the transparency of the films. Besides, the oxygen gas mixtures were also studied at the optimized sputtering power with a constant sputtering pressure. Optical and physical properties of the thin films were investigated using UV-Vis Spectrophotometer, FESEM, XRF, GIXRD, XRR including a microscratch tester. The Al2O3 films were highly transparent in the visible region in form of an …

Go to article

Extraction Of Cellulose Nanofibers From Empty Palm Fruit Bunches Via Mechanical Defibrillation, Zi-Qian Tan, Takaomi Kobayashi, Duangdao Aht-Ong Jan 2021

Extraction Of Cellulose Nanofibers From Empty Palm Fruit Bunches Via Mechanical Defibrillation, Zi-Qian Tan, Takaomi Kobayashi, Duangdao Aht-Ong

Journal of Metals, Materials and Minerals

In recent years, there has been an increasing interest in finding alternative material to replace fossil-oil based product due to the environmental concern. Lignocellulosic biomass has emerged as the promising candidate due to its low-cost and sustainability. The objective of this work was to prepare cellulose nanofibers (CNFs) from empty palm fruit bunches (EPFB), which are the waste originating from palm oil industry. Cellulose fibers were first extracted from EPFB by chemical treatment, followed by mechanical disintegration using high-pressure homogenization. Fiber concentration and defibrillation time during mechanical treatment were studied to investigate their effects on the properties of produced nanofibers. …

Go to article

The Effect Of Phosphogypsum On Stabilizing Clay Soil And Improving Its Properties For Use As Foundation Soil, Mai Yahya Maaitah, Mus'ab Ziad Banat Jan 2021

The Effect Of Phosphogypsum On Stabilizing Clay Soil And Improving Its Properties For Use As Foundation Soil, Mai Yahya Maaitah, Mus'ab Ziad Banat

Journal of Metals, Materials and Minerals

Expansive soil covers large areas in a variety of regions in Jordan which is insufficient to meet the engineering specifications in construction. Phosphogypsum is considered to be the main by-product material which comes from phosphate rock deposits that is available in Jordan. The main purpose of this research is to study the effects of stabilization by phosphogypsum on expansive soil properties. Three Jordanian regions were chosen to represent the expansive soils, Irbid, Madaba, and Abu-Nusire city. Soils were mixed with phosphogypsum at different percentages by dry weight of soil. Some of the representative laboratory tests for swell properties were conducted: …

Go to article

The Effect Of Artificial Defects On The Fatigue Characteristics Of Aisi 4340 Steel, Yakov B. Unigovski, Dmitry Fishman, Liat Fishman, Liron Shichman, Ofir Moshe, Roni Shneck, Emmanuel Gutman Jan 2021

The Effect Of Artificial Defects On The Fatigue Characteristics Of Aisi 4340 Steel, Yakov B. Unigovski, Dmitry Fishman, Liat Fishman, Liron Shichman, Ofir Moshe, Roni Shneck, Emmanuel Gutman

Journal of Metals, Materials and Minerals

This study examined the fatigue life (Nf) and fatigue limit (FL) of AISI 4340 steel in relation to surface roughness, artificial defects and shot peening. Artificial surface defects on fatigue specimens were obtained by electrical discharge machining (EDM) or by pre-corrosion in 3.5% NaCl and perchloric acid solutions, followed by a fatigue test. The presence of artificial defects of various sizes, taken into account by the area  parameter, led to a significant decrease in fatigue characteristics, while shot peening contributed to their noticeable improvement. Defects resulting from electrochemical corrosion had a much greater negative effect on fatigue …

Go to article

The Enhancement Of Ethanol Gas Sensors Response Based On Calcium And Zinc Co-Doped Lafeo3/Fe2o3 Thick Film Ceramics Utilizing Yarosite Minerals Extraction As Fe2o3 Precursor, Endi Suhendi, Zeany Luckyta Amanda, Muhamad Taufik Ulhakim, Andhy Setiawan, Dani Gustaman Syarif Jan 2021

The Enhancement Of Ethanol Gas Sensors Response Based On Calcium And Zinc Co-Doped Lafeo3/Fe2o3 Thick Film Ceramics Utilizing Yarosite Minerals Extraction As Fe2o3 Precursor, Endi Suhendi, Zeany Luckyta Amanda, Muhamad Taufik Ulhakim, Andhy Setiawan, Dani Gustaman Syarif

Journal of Metals, Materials and Minerals

A gas sensor is a renewed interest of research which has been developed to make a device that can be detected the harmful gases and applied in the several fields of industries. In this paper, we report the modified of gas sensor based thick film ceramic LaFeO3/Fe2O3 by added calcium and zinc co-doping prepared by screen-printed technique. In this work, yarosite mineral was utilized as Fe2O3 precursor. It aims to take the advantages of abundance natural resources in Indonesia to save a cost in gas sensor fabrication. Then, x-ray diffraction (XRD), scanning electron microscopy (SEM) and electrical properties characterization were …

Go to article

Wollastonite And Talc Reinforced Polypropylene Hybrid Composites: Mechanical, Morphological And Thermal Properties, Naruedee Putfak, Amnouy Larpkasemsuk Jan 2021

Wollastonite And Talc Reinforced Polypropylene Hybrid Composites: Mechanical, Morphological And Thermal Properties, Naruedee Putfak, Amnouy Larpkasemsuk

Journal of Metals, Materials and Minerals

This study focused on evaluating the mechanical, thermal, and morphological properties of polypropylene (PP) hybrid composites containing two different inorganic mineral fillers, namely wollastonite (WO) and talc. The composites were prepared by melt mixing process using a twin screw extruder and an injection molding machine. All composites contained a constant filler loading at 20 wt% with varying WO/talc weight ratios (20/0, 15/5, 10/10, 5/15, and 0/20). Melt flow index (MFI), mechanical properties (impact strength and tensile properties), heat distortion temperature (HDT) fractured surface morphology, and thermal behaviors of the resulting composites were investigated. The results revealed an enhancement in the …

Go to article

Effect Of Nitrocarburizing And Argon Admixing On Low Carbon Steel For Component Facility In Radiometallurgical Installation, Erwan Hermawan, Suprapto Suprapto, Usman Sudjadi, Siti Shaleha, Maman Kartaman Ajiriyanto Jan 2021

Effect Of Nitrocarburizing And Argon Admixing On Low Carbon Steel For Component Facility In Radiometallurgical Installation, Erwan Hermawan, Suprapto Suprapto, Usman Sudjadi, Siti Shaleha, Maman Kartaman Ajiriyanto

Journal of Metals, Materials and Minerals

Steel is an important component in the industrialized world with rising growth in world consumption. Steel has wide applications due to its high strength, durability, and cost-effectiveness. This has applications in the nuclear power plant. In Indonesian nuclear industry, low carbon steel is used not only for the fabrication of reactor components but also for the radiometallurgical facilities. However, to avoid the risk of premature failure and enhance the longevity of the components in the service condition, surface modification for the improvement of hardness has been realized. Amongst several methods, surface hardening by following nitrocarburizing has been found to be …

Go to article

Structural, Magnetic And Transport Properties Of Ca And Sr Doped Lanthanum Manganites, Sunita Keshri, Shailendra Rajput, Sonali Biswas, Leena Joshi, Wojciech Suski, Piotr Wiśniewski Jan 2021

Structural, Magnetic And Transport Properties Of Ca And Sr Doped Lanthanum Manganites, Sunita Keshri, Shailendra Rajput, Sonali Biswas, Leena Joshi, Wojciech Suski, Piotr Wiśniewski

Journal of Metals, Materials and Minerals

This article presents a comparative study for the effect of average A-site cation size on the structural, transport and magnetic properties of Lanthanum manganites. Three polycrystalline colossal magneto-resistive compounds were synthesized using standard solid state reaction method. The electrical resistivity data were analyzed employing standard two-phase model to understand the conduction mechanism. The resistance of polycrystalline ceramic depends on the intragrain resistance (intrinsic resistance) and the intergrain or grain-boundary resistance (extrinsic resistance). The substitution of Sr ions at La-site provides higher magnetic and metal-insulator transitions as compared to Ca ions. The combined substitution of Ca and Sr ions at La-site …

Go to article

Formation Of Nano-Crystalline Chromium-Zirconium Nitride (Cr-Zr-N) Film Coating By Dc Unbalanced Magnetron Sputtering, Kumpon Leelaruedee, Kattareeya Taweesup, Patama Visuttipitukul Jan 2021

Formation Of Nano-Crystalline Chromium-Zirconium Nitride (Cr-Zr-N) Film Coating By Dc Unbalanced Magnetron Sputtering, Kumpon Leelaruedee, Kattareeya Taweesup, Patama Visuttipitukul

Journal of Metals, Materials and Minerals

This research aimed to improve the properties of chromium nitride (CrN) film coatings by addition of zirconium (Zr) as the third element to form Cr-Zr-N ternary nitride. DC unbalanced magnetron sputtering method was used to form Cr-Zr-N film with various Zr/Zr + Cr atomic ratios.  Mechanical properties, surface morphology and crystal structure of the film were investigated. In the research, Cr-Zr-N film were categorised into 3 types with different Zr amount: low zirconium, (Zr/Zr + Cr = 0.29), medium zirconium (Zr/Zr + Cr = 0.44), and high zirconium (Zr/Zr + Cr = 0.74). All Cr-Zr-N films exhibited nano-crystalline structures with …

Go to article

Controlled Plasma Tuning Of Mos2 Based Photodetector: From Visible To Ultraviolet Photo Response, Huda Musa Mutlaq, Ali Jabbar Fraih Jan 2021

Controlled Plasma Tuning Of Mos2 Based Photodetector: From Visible To Ultraviolet Photo Response, Huda Musa Mutlaq, Ali Jabbar Fraih

Journal of Metals, Materials and Minerals

Among diverse family of two-dimensional materials, molybdenum disulfide (MoS2) is one of the most promising materials for optical applications thanks to its tunable optical energy bandgap. In this work, a MoS2 based photodetector is fabricated and its optical properties is investigated. With the help of controlled oxygen plasma bombardment, its photoresponse is tuned from visible to ultraviolet region. The photodetector was subjected to three bombardment times of 60 s, 120 s, and 180 s, and it was observed that 180 s irradiation resulted in a change in the optical response range of the photodetector from visible to ultraviolet. In fact, …

Go to article

Retaining The High-Temperature Phases Of Rb3h(So4)2 And Rb5h3(So4)4 At Room Temperature, Chatr Panithipongwut Kowalski Jan 2021

Retaining The High-Temperature Phases Of Rb3h(So4)2 And Rb5h3(So4)4 At Room Temperature, Chatr Panithipongwut Kowalski

Journal of Metals, Materials and Minerals

The attempts to maintain the higher-temperature phases of Rb3H(SO4)2 and Rb5H3(SO4)4 were demonstrated in this work for the first time. The goal was to explore the possibility to utilize solid acids at lower temperatures while keeping the high-temperature phases which connects to the desirable conductivities. Enabling to do so will allow the ease of handling and thermal cycling, and the energy saving in fuel cell applications, and will allow researchers to study the high-temperature properties of solid acids at lower temperatures without the expenses for the in-situ measurements and the accessibility limitations. The four relatively simple methods, which were the …

Go to article

Poly(Vinyl)Alcohol Film Composited With Carbon Dots From Water Hyacinth Stalks Based On Gamma Irradiation For The Uv Blocking Film, Tanagorn Kwamman, Threeraphat Chutimasakul, Panida Sangangam, Nattamon Puengposop, Kanokorn Wechakorn Jan 2021

Poly(Vinyl)Alcohol Film Composited With Carbon Dots From Water Hyacinth Stalks Based On Gamma Irradiation For The Uv Blocking Film, Tanagorn Kwamman, Threeraphat Chutimasakul, Panida Sangangam, Nattamon Puengposop, Kanokorn Wechakorn

Journal of Metals, Materials and Minerals

UV-radiation in the range of 200 nm to 400 nm from sunlight can inhibit the photosynthesis process in plants, while visible light in the range of 400 nm to 700 nm promotes photosynthesis and plant growth. In this work, poly(vinyl)alcohol-carbon dots composite film (PVA-CDs film) was developed as a UV-blocking film due to the excellent optical properties of carbon dots and the film-forming properties of PVA. For the synthesis of carbon dots using gamma irradiation, water hyacinth stalk, an invasive aquatic plant, was used as a carbon source. The result showed that PVA-CDs composite film exhibited excellent UV absorption (200 …

Go to article

Luminescent Properties Of Polyaniline Capped Mn Doped Zns Quantum Dots, Anju Bala, Rajeev Sehrawat, Anil Kumar Sharma, Pardeep Soni Jan 2021

Luminescent Properties Of Polyaniline Capped Mn Doped Zns Quantum Dots, Anju Bala, Rajeev Sehrawat, Anil Kumar Sharma, Pardeep Soni

Journal of Metals, Materials and Minerals

Synthesis of polyaniline capped and Mn doped quantum dots are performed with co-precipitation tech. while structural, optical and morphological properties have been carried out by using Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD) study, photoluminescent (PL), absorption spectroscopy and High-Resolution Transmission Electron Microscopy (HR-TEM). Particles size is nearly 2 nm calculated using XRD analysis and nearly 2.5 nm as estimated from HR-TEM study. FTIR spectra confirm that ZnS and polyaniline interact through S-H vibrations. The absorption spectra analysis reflects the occurrence of blue shift at the peak of absorption along with the enhanced band gap of polyaniline capped ZnS(Mn) …

Go to article

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu Jan 2021

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Go to article

Determination Of Hydrogel Degradation By Passive Mechanical Testing, Avery Rosh-Gorsky Jan 2021

Determination Of Hydrogel Degradation By Passive Mechanical Testing, Avery Rosh-Gorsky

Honors Theses

This paper details a new technique to measure the mechanical properties of ETTMP PEGDA hydrogels using Hertz Contact Theory and simultaneously analyze both the model drug release and gel erosion in situ. This method involves curing a drug loaded hydrogel in a standard cuvette and placing a glass bead and phosphate buffer solution (PBS). Over time, the cross-linked network of the hydrogel breaks down, and, as a result, the ball sinks into the hydrogel. This method provides a macroscopic and inexpensive way to continuously and passively measure properties of the hydrogel as the hydrogel degrades. By plotting both the …

Go to article

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter Jan 2021

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Go to article

Application Of Laser Assisted Ultrasonic Nanocrystal Surface Modification On Aluminum And 3d Printed Titanium, Eman Hassan, Thomas Crouse Jan 2021

Application Of Laser Assisted Ultrasonic Nanocrystal Surface Modification On Aluminum And 3d Printed Titanium, Eman Hassan, Thomas Crouse

Williams Honors College, Honors Research Projects

A novel surface treatment, laser assisted ultrasonic nanocrystal surface modification (LA-UNSM), has proved effective in increasing surface hardness, and fatigue life. The objective of this research is to determine the effectiveness of this process on components created with additive manufacturing. To accomplish this, we investigated the effectiveness of LA-UNSM treatment on aluminum, a common 3d printed metal, and the effectiveness of LA-UNSM processing on 3d printed titanium. We first conducted our own literature review to assess the practicality of using this same treatment on aluminum. We then treated traditionally manufactured aluminum at varying levels of laser intensity to determine if …

Go to article

Development Of An Injectable Methylcellulose Hydrogel System For Nucleus Pulposus Repair And Regeneration, Nada A. Haq-Siddiqi Jan 2021

Development Of An Injectable Methylcellulose Hydrogel System For Nucleus Pulposus Repair And Regeneration, Nada A. Haq-Siddiqi

Dissertations and Theses

Low back pain is the most common cause of disability in the world and is often caused by degeneration or injury of the intervertebral disc (IVD). The IVD is a complex, fibrocartilaginous tissue that allows for the wide range of spinal mobility. Disc degeneration is a progressive condition believed to begin in the central, gelatinous nucleus pulposus (NP) region of the tissue, for which there are few preventative therapies. Current therapeutic strategies include pain management and exercise, or surgical intervention such as spinal fusion, none of which address the underlying cause of degeneration. With an increasingly aging population, the socioeconomic …

Go to article

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand Jan 2021

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Go to article

Synthesis Of A Two-Part Geopolymer From Red Mud And Silica Fume, Arup Kumar Mandal Jan 2021

Synthesis Of A Two-Part Geopolymer From Red Mud And Silica Fume, Arup Kumar Mandal

Journal of Metals, Materials and Minerals

In this present study, the development of a two-part geopolymer from waste red mud (RM) and silica fume (SF) by alkali activator is examined. The influence of silica fume addition, alkali concentration, curing duration are studied. The compressive strength of geopolymers has been achieved 0.8 MPa to 8 MPa with varying different compositions and synthesis parameters. The optimum RM/SF ratio is 60/40, the optimum solid/solution ratio is 1.8 gmL-1 or 2 gmL-1, and the optimum Na2SiO3/NaOH ratio is 0.5 day for 28 days curing time. The incorporation of iron in the geopolymer matrix contributes to geopolymerization. The study suggests that …

Go to article

Eco-Friendly Lake Pigment From Sappanwood: Adsorption Study And Its Application As Natural Colorant For Natural Rubber Toy Balloon, Jitnapa Sirirak, Ployphat Suppharatthanya, Kedsarin Chantha, Sutinee Girdthep, Supanee Chayabutra Jan 2021

Eco-Friendly Lake Pigment From Sappanwood: Adsorption Study And Its Application As Natural Colorant For Natural Rubber Toy Balloon, Jitnapa Sirirak, Ployphat Suppharatthanya, Kedsarin Chantha, Sutinee Girdthep, Supanee Chayabutra

Journal of Metals, Materials and Minerals

Due to the awareness of the impact of synthetic dye on human health and the environment, natural dye and lake pigment have attracted considerable attention from researcher. Herein, pink−red lake pigment from sappanwood was prepared using adsorption approach. The effects of initial pH, pH and concentration of brazilein solution, dosage of aluminium hydroxide, and adsorption time on adsorption were also explored. Results showed that the maximum adsorption capacity of 30 mg g-1 was achieved when 0.25%w/v of aluminium hydroxide and 100 mg L-1 of brazilein solution were applied. The adsorption kinetics and adsorption isotherm fitted the pseudo second order model …

Go to article

Using Shrimp Shells As Based Catalysts For Fame Production From Palm Oil Feedstock, Assadaporn Poonanan, Anupat Prukpaiboon, Paul Egwuonw Dim, Mutsee Termtanun Jan 2021

Using Shrimp Shells As Based Catalysts For Fame Production From Palm Oil Feedstock, Assadaporn Poonanan, Anupat Prukpaiboon, Paul Egwuonw Dim, Mutsee Termtanun

Journal of Metals, Materials and Minerals

In this study, waste shrimp shells from industry were used as a heterogeneous bio-based catalyst for trans-esterification reaction of fresh palm oil. CaO was prepared from shrimp shells calcination. Surface area, phase composition, and basicity of the calcined shrimp shell catalysts were studied using N2 adsorption (BET), X-ray diffraction (XRD), and CO2 temperature-programmed-desorption (CO2-TPD), respectively. The influence of shrimp shells calcination temperature and operation condition, methanol to palm oil ratio on trans-esterification reaction, were investigated. Five hours trans-esterification was carried out at 65℃ using different shrimp shell at four different calcination temperature: 700, 750, 800 and 850℃ with 9:1 methanol …

Go to article

Investigation Of Deposition Parameters On The Structural Properties And Hardness Of Tialn Films Deposited Via Reactive Pulsed Dc Magnetron Sputteringinvestigation Of Deposition Parameters On Structural Properties And Hardness Of Tialn Films Deposited By Reactive Pulsed Dc Magnetron Sputtering, Jariyaporn Rukkun, Kamon Aiempanakit, Pimchanok Reakaukot, Witthawat Wongpisan, Kirati Waree, Montri Aiempanakit Jan 2021

Investigation Of Deposition Parameters On The Structural Properties And Hardness Of Tialn Films Deposited Via Reactive Pulsed Dc Magnetron Sputteringinvestigation Of Deposition Parameters On Structural Properties And Hardness Of Tialn Films Deposited By Reactive Pulsed Dc Magnetron Sputtering, Jariyaporn Rukkun, Kamon Aiempanakit, Pimchanok Reakaukot, Witthawat Wongpisan, Kirati Waree, Montri Aiempanakit

Journal of Metals, Materials and Minerals

In this work, titanium aluminum nitride (TiAlN) films were deposited on a silicon substrate via reactive pulsed DC magnetron sputtering. The effect of deposition parameters such as nitrogen gas flow rate, substrate temperature, and bias voltage on the structural and mechanical properties of TiAlN films was investigated. The crystal structure, morphology, and hardness of TiAlN films were characterized via X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM, and nanoindentation. An improved crystallinity of TiAlN films was obtained by varying the substrate temperature and bias voltage. The morphology of the TiAlN film exhibited a columnar structure, and the morphology gradually …

Go to article

Improving Corrosion Resistance Of 3d Printed Ti-6al-4v By Tin Coating, Surada Nisaimun, Phitsanu Poolcharuansin, Patama Visuttipitukul, Pitichon Klomjit Jan 2021

Improving Corrosion Resistance Of 3d Printed Ti-6al-4v By Tin Coating, Surada Nisaimun, Phitsanu Poolcharuansin, Patama Visuttipitukul, Pitichon Klomjit

Journal of Metals, Materials and Minerals

TiN thin films were deposited on biomaterial 3D printed Ti-6Al-4V substrates using two methods including direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS). The coating times were compared between 5 min and 25 min. HiPIMS was developed based on DCMS by increasing degree of ionization in plasma and power densities in the order of kWcm-2 compared to Wcm-2 of DCMS. The film characteristics and mechanical properties were investigated by glancing incident x-ray diffractometer (GIXRD), field emission scanning electron microscope (FE-SEM), and atomic force microscope (AFM). Electrochemical behavior was analyzed by electrochemical impedance spectroscopy (EIS) in 1 M …

Go to article

Characteristic Of Fluorescence Spectroscopy Response Of Tetrakis (4-Sulfonatophenyl) Porphyrin Doped Polyaniline Toward Fe3+ Ion, Chatr Panithipongwut Kowalsk, Meatawadee Buntee, Prasit Pattananuwat Jan 2021

Characteristic Of Fluorescence Spectroscopy Response Of Tetrakis (4-Sulfonatophenyl) Porphyrin Doped Polyaniline Toward Fe3+ Ion, Chatr Panithipongwut Kowalsk, Meatawadee Buntee, Prasit Pattananuwat

Journal of Metals, Materials and Minerals

Here, we report a selective colorimetric chemosensor toward Fe3+ ion detection by the combination of sensitizer and hole transport consisting of polyaniline and tetrakis (4-sulfonatophenyl) porphyrin. Interestingly, the presence of tetrakis (4-sulfonatophenyl) porphyrin moiety on polyaniline can enhance the optical limiting properties of polyaniline, allowing the fluorophore signal for chemical sensor. The performance sensing behaviors toward metal ion are observed by the ultraviolet-Visible and fluorescence properties. The sensing of polyaniline-tetrakis (4-sulfonatophenyl) porphyrin toward Fe3+ ion exhibits a linear response in the concentration range of 0.01 M to 1.0 × 10-4 M over the other transition metals (Cu2+, Ni2+, Zn2+, Pb2+, …

Go to article

The Study On Un-Doped/Boron Doped/Un-Doped Triple Seg In Vertical Nand Flash Memory, Woong Lee, Chaeho Kim, Joonsuk Lee, Sehun Park, Yonghan Roh Jan 2021

The Study On Un-Doped/Boron Doped/Un-Doped Triple Seg In Vertical Nand Flash Memory, Woong Lee, Chaeho Kim, Joonsuk Lee, Sehun Park, Yonghan Roh

Journal of Metals, Materials and Minerals

Selective epitaxial growth (SEG) plays a critical role in vertical NAND flash memory because it serves as a ground select line (GSL) transistor, which is used to control the cell current in the vertical channel. In this study, different channel hole sizes between the adjacent hole and away hole from the common source line (CSL) were detected after vertical channel etch (VCE). This discrepancy severely impacts the boron concentration of SEG applied through ex-situ boron implantation, and results in large GSL Vth variations. Novel in-situ boron-doping of triple-layered un-doped/boron doped/un-doped SEG was developed to solve the high variation of the …

Go to article

Microwave-Assisted Ecofriendly Silver Nanoparticle Synthesis By Varieties Of Chrysanthemum Morifolium Ramat: Assessing Their Antioxidant, Photocatalytic And Antibacterial Activities, Mathivathani Kandiah, Laknee Nawamali De Silva Jan 2021

Microwave-Assisted Ecofriendly Silver Nanoparticle Synthesis By Varieties Of Chrysanthemum Morifolium Ramat: Assessing Their Antioxidant, Photocatalytic And Antibacterial Activities, Mathivathani Kandiah, Laknee Nawamali De Silva

Journal of Metals, Materials and Minerals

Based on recent developments in the field of Nanobiotechnology, this study is aimed at the assessment of antioxidant, photocatalytic and antibacterial activities of silver nanoparticles (AgNPs) synthesized using Chrysanthemum morifolium Ramat varieties (brown, yellow, purple, pink, salmon pink and white), where five varieties produced AgNPs except white. Antioxidant assays such as total flavonoid content, total phenolic content and total antioxidant capacity and free radical scavenging assays such as ferric reducing antioxidant power and DPPH radical scavenging assays were performed. Photocatalytic activity was assessed by the degradation of the model dye methylene blue. Anti-bacterial activity was determined on Staphylococcus aureus and …

Go to article

First Prev Next Last