Engineering Science and Materials Commons^™

Using Dft On Ultrasound Measurements To Determine Patient-Specific Blood Flow Boundary Conditions For Computational Hemodynamics Of Intracranial Aneurysms, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Boundary conditions (BCs) is one pivotal factor influencing the accuracy of hemodynamic predictions on intracranial aneurysms (IAs) using computational fluid dynamics (CFD) modeling. Unfortunately, a standard procedure to secure accurate BCs for hemodynamic modeling does not exist. To bridge such a knowledge gap, two representative patient-specific IA models (Case-I and Case-II) were reconstructed and their blood flow velocity waveforms in the internal carotid artery (ICA) were measured by ultrasonic techniques and modeled by discrete Fourier transform (DFT). Then, numerical investigations were conducted to explore the appropriate number of samples (N) for DFT modeling to secure the accurate BC by comparing …

Numerical Investigation Of Supersonic Flow Over A Wedge By Solving 2d Euler Equations Utilizing The Steger–Warming Flux Vector Splitting (Fvs) Scheme, Mitch Wolff, Hashim H. Abada, Hussein Awad Kurdi Awad Kurdi Saad

Mechanical and Materials Engineering Faculty Publications

Supersonic flow over a half-angle wedge (θ = 15°) with an upstream Mach number of 2.0 was investigated using 2D Euler equations where sea level conditions were considered. The investigation employed the Steger–Warming flux vector splitting (FVS) method executed in MATLAB 9.13.0 (R2022b) software. The study involved a meticulous comparison between theoretical calculations and numerical results. Particularly, the research emphasized the angle of oblique shock and downstream flow properties. A substantial iteration count of 2000 iteratively refined the outcomes, underscoring the role of advanced computational resources. Validation and comparative assessment were conducted to elucidate the superiority of the Steger–Warming flux …

Analysis Of Additively Manufactured Inconel 718 Combustion Behavior In Promoted Oxygen Environments, Dominic George Dieguez

Open Access Theses & Dissertations

Promoted combustion testing is a vital tool for engineers to establish the combustion and flammability characteristics of materials (metallic or otherwise) in oxygen enriched environments. Historically, much of the established data for metallic promoted combustion has been with regards to materials in their cast and wrought forms. However, with the emergence of additive manufacturing as a preferred method of fabrication, the need exists to evaluate how metals in that form behave. Recent testing has demonstrated that even if a metal or alloy is nominally the same with regards to chemistry, flammability between samples in the wrought form can differ significantly …

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

Investigation On The Effects Of Biofouling On The Boundary Layer, Adam N. Bacon

LSU New Orleans Theses and Dissertations

This study is an investigation of the effect of biofouling on the boundary layer of a flat plate and a NACA 4-digit series foil. Three identical hydrofoils made of resin were placed in the Gulf of Mexico at Grand Isle, Louisiana, and observed and analyzed by marine biologists at the University of New Orleans for their species composition. The resulting biofouling that grew was primarily made up of barnacles and bryozoans. The foils were submerged in an open channel flume at zero incidence and subjected to a series of experiments whose arc-length Reynolds numbers ranged from approximately 13000 to 32000. …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Deep Learning Based Optical Flow Analysis Of High-Speed Flows, Daniel H. Zhang, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

Two-dimensional Rayleigh scattering imaging is utilized to quantify the high-speed flow velocity by employing deep learning based optical flow analysis, along with density fields from Rayleigh scattering intensity profiles.

Generating Blood Analog For Laser Induced Fluorescent Particle Image Velocimetry, Chungyiu Ma, Jared Chong, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

To mimic blood non-Newtonian viscosity features under designated temperatures from 305 to 315 K, transparent blood analogs were generated by the mixture of xanthan gum and deionized water with fluorescent particles for laser induced fluorescent particle image velocimetry.

3d Flow Field Quantification In An Artery Model Using Optical Flow Method Based On Simulated Multi-Angle Angiography, Zifeng Yang, Hang Yi, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

3D flow field in a numerically simulated arterial model is quantified using the three-dimensional optical flow method based on simulated simultaneous multi-angle X-ray angiography of the blood flow with contrast agent perfusions.

Mechanics Of Pure Bending And Eccentric Buckling In High-Strain Composite Structures, Jimesh D. Bhagatji, Oleksandr G. Kravchenko, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This paper presents fabrication, experimental testing, and progressive failure modeling to study the deformation of an ultra-thin composite beam. The research study examines the deformation modes of a post-deployed boom under repetitive pure bending loads using a four-point bending setup and …

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Dual Airfoil Testing System, Zifeng Yang, Collin Charvat, Jack Stafford, Kyle Mathews, Logan Kelly

Mechanical and Materials Engineering Faculty Publications

A dual airfoil testing system includes a platform including a frame defining a chamber that is configured to receive a horizontal flow of air for testing a first airfoil and a second airfoil contained in the chamber and a control system including a controller to control a first attack angle stepper motor, a second attack angle stepper motor, at least one gap stepper motor, and at least one stagger stepper motor. The controller is configured to automatically control and adjust the stepper motors to control and adjust the attack angle of the first airfoil, the attack angle of the second …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Experimental Characterization And Quantification Of Deformation Behavior In A Porous Carbon Fiber Network, Robert N Quammen

Theses and Dissertations--Chemical and Materials Engineering

Due to their wide range of attractive functional properties (such as low thermal conductivity and low density) porous materials are utilized in a variety of applications. In order to characterize these properties and others, the intrinsically heterogeneous microstructures of these materials need to be taken into account. These microstructures result in interactions across multiple length scales spanning several orders of magnitude. This makes the creation of robust computational models and straight-forward predictions of mechanical properties difficult for porous materials. With this in mind, this dissertation aims to provide experimental mechanical and deformation information spanning the length scales of interest for …

Multi-Mode Regulation Of The Drying Process Of Industrial Gas, Isamidin Xakimovich Sidikov Pr, Nashvandova Gulruxsor Murot Qizi Phd

Technical science and innovation

Currently, much attention is paid to the issue of energy efficiency of gas processing enterprises. The continuous growth of world prices for energy resources requires constant improvement of the management system, providing the most optimal conditions for the flow of technological processes. A conceptual model of the heat-mass transfer process occurring in the absorber as an object of research has been developed, which characterizes the relationship of the variables involved in the drying process of natural gas, control, measurable and immeasurable, as well as controlled parameters have been selected, which are used to develop and study a mathematical model of …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Ultra Wide Band Gap Oxides For Advanced Optoelectronics And Supercapacitor Applications: A Case Study Of Intrinsic And Doped Germanium Dioxide, Paul Gaurav Nalam

Open Access Theses & Dissertations

Germanium dioxide (GeO2) is a metal oxide semiconductor with multiple polymorphs that has recently garnered a significant amount of scientific attention owing to its novel ultra-wide band gap and pseudo-capacitive properties, which can potentially transcend current power electronic, optoelectronic, and supercapacitor technologies. However, due to the difficulty in the synthesis of stable crystalline phases of individual polymorphs of GeO2 thin films, this material system demands complex and resource-intensive deposition techniques to synthesize. An attempt was made to develop cost-effective and scalable deposition techniques to stabilize specific crystalline phases of GeO2 thin films. These phases were further structurally fine-tuned to state …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Augmenting External Surface Pressures’ Predictions On Isolated Low-Rise Buildings Using Cfd Simulations, Md Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

The aim of this paper is to enhance the accuracy of predicting time-averaged external surface pressures on low-rise buildings by utilizing Computational Fluid Dynamics (CFD) simulations. To achieve this, benchmark studies of the Silsoe cube and the Texas Tech University (TTU) experimental building are employed for comparison with simulation results. The paper is structured into three main sections. In the initial part, an appropriate domain size is selected based on the precision of mean pressure coefficients on the windward face of the cube, utilizing Reynolds Averaged Navier-Stokes (RANS) turbulence models. Subsequently, recommendations regarding the optimal computational domain size for an …

Switching Methods For Three-Dimensional Rotational Dynamics Using Modified Rodrigues Parameters, Matthew Jarrett Banks

Mechanical & Aerospace Engineering Theses & Dissertations

A rigid body in space has three degrees of rotational freedom. As a result, a minimum of three independent parameters is required to define the three-dimensional orientation of a rigid body. As is well known, every set of three independent parameters has at least one orientation where mathematical or geometrical singularities are encountered; therefore, when the use of a three-parameter representation is desired, a method for singularity avoidance must also be considered. A common practice for singularity avoidance is to switch between parameter sets whose singularities occur at different orientations. With this in mind, modified Rodrigues parameters (MRP) are considered …

Development, Experimental Validation, And Progressive Failure Modeling Of An Ultra-Thin High Stiffness Deployable Composite Boom For In-Space Applications, Jimesh D. Bhagatji

Mechanical & Aerospace Engineering Theses & Dissertations

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This research focuses on fabrication, experimental testing, and progressive failure modelling to study the deformation of an ultra-thin composite beam. The research study examines deformation modes of a boom under repetitive pure bending loads using 4-point bending setup. The material and …

The Plastics Collection Reference Packet, Special Collections Research Center

Special Collections Research Center

This reference packet is an informational tool to support further research into the history of plastics—whether interested in companies, individuals within the plastics industry's history, historical plastics materials, essays, and more. All content featured within this packet was previously published on the former plastics.syr.edu website as part of a Syracuse University Libraries and Special Collections Research Center (SCRC) partnership established in 2007 with the Plastics Pioneers Association (PPA)—an association of plastics industry professionals interested in preserving the plastics industry's past.

Morphology And Hemodynamics Of Cerebral Arteries And Aneurysms In A Rare Pair Of Monozygotic Twins, Hang Yi, Zifeng Yang, Luke C. Bramlage, Bryan R. Ludwig

Mechanical and Materials Engineering Faculty Publications

In this preliminary study, the underlying pathophysiology mechanisms of cerebral aneurysms (CAs) in monozygotic twins (MTs) were investigated via a rare pair of MTs (twin A and twin B) involving four reconstructed arterial models using preclinical information. First, dimensions and configurated outlines of three-perspective geometries were compared. Adopting an in-vitro validated numerical CA model, hemodynamic characteristics were investigated in the MTs, respectively. Despite expected genetic similarities, morphological comparisons show that configurations of cerebral arteries exhibit significant differences between the twins. The ICA size of twin A is larger than that in twin B (2.23~25.86%), varying with specific locations, attributing to …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Mechanical Properties And Performance Of A Novel Nano-Engineered Unitized Composite With Quasi-Isotropic Layup, Brian Matthew Pudlo

Theses and Dissertations

Carbon nanotubes (CNTs) exhibit outstanding mechanical, electrical, and thermal properties, but are a challenge to effectively implement into macroscopic composites for aerospace applications. This research investigates the mechanical properties and performance of a newly developed hybrid NanoStitch composite, alongside a control polymer matrix composite, at room temperature. Both composite material systems investigated in this work have quasi-isotropic layup. Monotonic tension-tofailure, tension-tension fatigue, and creep tests were performed to characterize the performance of the composites under cyclic and sustained loading. Experimental results obtained for the quasi-isotropic NanoStitch composite were compared to those obtained for the quasi-isotropic control composite. The properties and …

Towards An Understanding Of The Thermodynamic Properties Of Crtao4: A Computational Perspective, Tanner B. Gordon

Theses and Dissertations

Materials that can withstand higher temperatures are paramount for next-generation aircraft design. Hypersonic capabilities and jet-turbine engines operate in extreme environments. Choosing materials that have high thermal stability and oxidation resistance for these applications can increase engine efficiency, reduce size, weight and power (SWaP), and increase the maneuverability of the aircraft. The mixed oxide CrTaO₄ has been experimentally observed to significantly contribute to oxidation resistance at high temperatures. However, and despite its significance, its properties remain largely unknown. This work explores the thermal properties of this material from a multi-scale approach, by obtaining an accurate description of the thermodynamics …

Hemodynamic Investigations In Intracranial Aneurysms: A Commentary, Hang Yi, Mark Johnson, Luke Bramlage, Zifeng Yang, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Intracranial aneurysms (IAs) are abnormal bulges in a blood vessel in the brain that have a potential to rupture and even causing a stroke, which can lead to lasting brain damage, long-term disability, or even loss of life. It has been widely acknowledged that hemodynamic factors, e.g., instantaneous wall shear stress, time-averaged wall shear stress, wall shear stress gradient, gradient oscillatory number, oscillatory shear index, pulsatile blood flow waveform (flow rate magnitude and shape, physical flow period), relative residence time/turnover time, blood pressure, and vortex (i.e., size, location, and numbers), have a close relationship with the pathobiology (i.e., initiation, growth, …