VLSI and Circuits, Embedded and Hardware Systems Commons^™

Switching Trajectory Control For High Voltage Silicon Carbide Power Devices With Novel Active Gate Drivers, Shuang Zhao

Graduate Theses and Dissertations

The penetration of silicon carbide (SiC) semiconductor devices is increasing in the power industry due to their lower parasitics, higher blocking voltage, and higher thermal conductivity over their silicon (Si) counterparts. Applications of high voltage SiC power devices, generally 10 kV or higher, can significantly reduce the amount of the cascaded levels of converters in the distributed system, simplify the system by reducing the number of the semiconductor devices, and increase the system reliability.

However, the gate drivers for high voltage SiC devices are not available on the market. Also, the characteristics of the third generation 10 kV SiC MOSFETs …

Compact Modeling Of Sic Insulated Gate Bipolar Transistors, Sonia Perez

Graduate Theses and Dissertations

This thesis presents a unified (n-channel and p-channel) silicon/silicon carbide Insulated Gate Bipolar Transistor (IGBT) compact model in both MAST and Verilog-A formats. Initially, the existing MAST model mobility equations were updated using recently referenced silicon carbide (SiC) data. The updated MAST model was then verified for each device tested. Specifically, the updated MAST model was verified for the following IGBT devices and operation temperatures: n-channel silicon at 25 ˚C and at 125 ˚C; n-channel SiC at 25 ˚C and at 175 ˚C; and p-channel SiC at 150 ˚C and at 250 ˚C. Verification was performed through capacitance, DC output …

High Temperature Cmos Silicon Carbide Asynchronous Circuit Design, Landon John Caley

Graduate Theses and Dissertations

Designing a digital circuit to operate in an extreme temperature range is a challenge with increasing demand for a solution. Large variations in temperature have a distinct impact on electron mobilities causing substantial changes to the threshold voltage of the devices. These physical changes affect the setup and hold times of clocked components, such as D-Flip Flops, of a traditional synchronous digital circuit. Focusing primarily on high temperature circuit operation, this dissertation presents a digital circuit design methodology pairing an asynchronous circuit design paradigm called NULL Convention Logic (NCL) as well as traditional Boolean circuitry with a wide-bandgap semiconductor material, …

Design, Layout, And Testing Of A Silicon Carbide-Based Under Voltage Lock-Out Circuit, Michael Dalan Glover

Graduate Theses and Dissertations

Silicon carbide-based power devices play an increasingly important role in modern power conversion systems. Finding a means to reduce the size and complexity of these systems by even incremental amounts can have a significant impact on cost and reliability. One approach to achieving this goal is the die-level integration of gate driver circuitry with the SiC power devices. Aside from cost reductions, there are significant advantages to the integration of the gate driver circuits with the power devices. By integrating the gate driver circuitry with the power devices, the parasitic inductances traditionally seen between the gate driver and the switching …

A Silicon Carbide Based Solid-State Fault Current Limiter For Modern Power Distribution Systems, Erik Darnell Johnson

Graduate Theses and Dissertations

The fault current limiter represents a developing technology which will greatly improve the reliability and stability of the power grid. By reducing the magnitude of fault currents in distribution systems, fault current limiters can alleviate much of the damage imposed by these events. Solid-state fault current limiters in particular offer many improved capabilities in comparison to the power system protection equipment which is currently being used for fault current mitigation. The use of silicon carbide power semiconductor devices in solid-state fault current limiters produces a system that would help to advance the infrastructure of the electric grid.

A solid-state fault …

The Development And Packaging Of A High-Density, Three-Phase, Silicon Carbide (Sic) Motor Drive, Jared Hornberger

Graduate Theses and Dissertations

Technology advances within the power electronics field are resulting in systems characterized by higher operating efficiencies, reduced footprint, minimal form factor, and decreasing mass. In particular, these attributes and characteristics are being inserted into numerous consumer applications, such as light-emitting diode lighting, compact fluorescent lighting, smart phones, and tablet PCs, to industrial applications that include hybrid, electric, and plug-in electric vehicles and more electric aircraft. To achieve the increase in energy efficiency and significant reduction in size and mass of these systems, power semiconductor device manufacturers are developing silicon carbide (SiC) semiconductor technology.

In this dissertation, the author discusses the …

Characterization And Modeling Of 4h-Sic Low Voltage Mosfets And Power Mosfets, Mihir Mudholkar

Graduate Theses and Dissertations

The integration of low voltage and high voltage circuits on SiC has profound applications. SiC power devices have proved their superiority in terms of high temperature operation, faster switching frequencies and larger power densities when compared with Si power devices. The control of SiC power devices however, lies in the hands of low voltage circuits built on Si. Thus, there exists a separation in the overall system between the low voltage and high voltage side, which increases system cost, weight and reduces efficiency. With the advancement in low voltage SiC processing technology, low voltage control circuits can be made on …