Systems and Communications Commons^™

Computational Modeling For Transportation Network Security, Sherif A. Tolba

Master's Theses

No abstract provided.

An Rf Cmos Implementation Of An Adaptive Filter For Narrow-Band Interferer Suppression In Uwb Systems, Markus Both

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Ultra-wideband (UWB) technology is a new type of technology for wireless communication that is based on the transmission of low power sub-nanosecond pulses. UWB communication utilizes a large bandwidth that overlaps and is coexistent with other wireless communication standards that can be also considered as narrow-band interferers. Because UWB systems are highly susceptible to narrow-band interferers, there is a demand for interferer suppression. An adaptive filter consisting of a two-element diversity receiver that performs minimum mean square error combining (MMSE) by the LMS algorithm is proposed. Thereby the elements of the LMS algorithm as well as the receiver LNA were …

Mapping Device With Wireless Communication, Xiangyu Liu

Electrical Engineering Undergraduate Honors Theses

Wireless communication is one of the most powerful communication methods that people use nowadays. The key advantage of wireless communications is that it can cover large distances without having to run any cables from one end to the other. Based on this advantage, wireless communication has many important applications, such as remote controls, cell phones, and global positioning system (GPS). This senior design project is developed to use wireless communication technology to map the geographic characteristics of an unknown place. It contains two wireless communication modules with Atmega1281 microprocessor, two robots with the 8051 microcontroller, six pairs of infrared transmitters …

Value Capture In Global Production Networks: Evidence From The Taiwanese Electronics Industry, Namchul Shin, Alan Eisner

Cornerstone 3 Reports : Interdisciplinary Informatics

No abstract provided.

Auto-Tuning Antenna, John Chen, Jennifer Tighe

Electrical Engineering

Radio transmitters and antennas have differing impedances at the output and feedpoint, depending on frequency. Modern antenna tuning methods involve manual or automatic resistance and reactance network adjustment to match transmitter and antenna impedance. This reduces power reflections to the transmitter, but introduces losses and prevents full transmitter power from being radiated at the antenna. This project utilizes a variable length antenna element to tune and match transmitter and antenna impedances, allowing efficient power transfer to the antenna. The antenna length varies from 0 to 30.5 inches. The method involves an RF signal with a maximum power of 2 watts …

Development Of A Simulation Tool For Analysis Of Freeway Crashes Due To Cell Phone Usage, Sourabh Sriom

UNLV Theses, Dissertations, Professional Papers, and Capstones

Research shows that drivers are susceptible to numerous distractions while driving which can be held responsible as the reason of a crash. Usage of cell phones, i.e. talking or texting while driving is considered one of the prominent distractions which causes a crash. This dissertation aims to study the number of crashes occurring on the freeways and their relation with the drivers of these cars using cell phones while they are driving. Since crashes occur relatively less frequently, the study of crashes is done using what is called the "rare event" theory. Java based simulations are done to model a …

Power Control And Security Games For Wireless Communication Networks, Bo Liang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, game theoretic analysis of wireless communication networks has been performed. Game theory provides valuable tools can be used to solve problem of conflict and cooperation in wireless communication networks. Game theoretic tools can be applied to multiple layers of wireless networks. First, we consider power control issues at the physical layer of wireless networks. A game theoretic analysis for resource allocation policies in fading interference channels in the presence of quality of service (QoS) constraints is performed. We model a two player non-cooperative power control game and assume that both transmitters and receivers know the channel side …

A Comparison Of Bss Algorithms In Harsh Environments, Christopher Osterwise, Steven Grant

Electrical and Computer Engineering Faculty Research & Creative Works

This paper compares the performance of several blind source separation (BSS) algorithms in environments of varying reverberation, noise, microphone spacing, and sparsity. of particular interest are two frequency domain algorithms: one Cascaded ICA with Intervention Alignment (CICAIA), and one algorithm by Pham, Servire, and Boumaraf. the former is found to work exceptionally well in high noise, low microphone spacing environments. the latter proves to work exceptionally well in high SNR and moderate- to widely spaced arrays. in addition, while the literature on BSS algorithms is extensive, their performance under varying noise conditions has not been widely explored. Also, though usually …

Calibration And 3-D Sound Reproduction In The Immersive Audio Environment, Pratik Shah, Steven Grant, William Chapin

Electrical and Computer Engineering Faculty Research & Creative Works

The effectiveness of virtual environments depends largely on how efficiently they recreate the real world. in the case of auditory virtual environments, the importance of accurate recreation is enhanced since there are no visual cues to assist perception, as in the case of audio-visual virtual environments. in this paper, we present the Immersive Audio Environment (IAE), an easily constructible and portable structure, which is capable of 3-D sound auralization with very high spatial resolution. a novel method for acoustically positioning loudspeakers in space, which is required by the IAE for simulation of sound sources, is presented in this paper. Our …

Low Complexity Feature Extraction For Classification Of Harmonic Signals, Peter William

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this dissertation, feature extraction algorithms have been developed for extraction of characteristic features from harmonic signals. The common theme for all developed algorithms is the simplicity in generating a significant set of features directly from the time domain harmonic signal. The features are a time domain representation of the composite, yet sparse, harmonic signature in the spectral domain.The algorithms are adequate for low-power unattended sensors which perform sensing, feature extraction, and classification in a stand-alone scenario. The first algorithm generates the characteristic features using only the duration between successive zero-crossing intervals. The second algorithm estimates the harmonics’ amplitudes of …

Proportionate Affine Projection Sign Algorithms For Network Echo Cancellation, Zengli Yang, Yahong Rosa Zheng, Steven L. Grant

Electrical and Computer Engineering Faculty Research & Creative Works

Two proportionate affine projection sign algorithms (APSAs) are proposed for network echo cancellation (NEC) applications where the impulse response is often real valued with sparse coefficients and long filter length. the proposed proportionate-type algorithms can achieve fast convergence and low steady-state misalignment by adopting a proportionate regularization matrix to the APSA. Benefiting from the characteristics of l1-norm optimization, affine projection, and proportionate matrix, the new algorithms are more robust to impulsive interferences and colored input than the proportionate least mean squares (PNLMS) algorithm and the robust proportionate affine projection algorithm (Robust PAPA). the new algorithms also achieve much faster convergence …

Proportionate Affine Projection Sign Algorithms For Sparse System Identification In Impulsive Interference, Zengli Yang, Yahong Rosa Zheng, Steven L. Grant

Electrical and Computer Engineering Faculty Research & Creative Works

Two proportionate affine projection sign algorithms (APSAs) are proposed for system identification applications, such as network echo cancellation (NEC), where the impulse response is often real valued with sparse coefficients and long filter length. the proposed proportionate-type algorithms can achieve fast convergence and low steady-state misalignment by adopting a proportionate regularization matrix to the APSA. Benefiting from the characteristic of l1-norm algorithms, affine projection, and proportionate matrix, the new algorithms are robust to impulsive interferences and colored input and achieve much faster convergence rate in sparse impulse responses than the original APSA, the normalized sign algorithm (NSA), and the proportionate …

Chaotic Bandgaps In Hybrid Acousto-Optic Feedback And Their Implications, Monish Ranjan Chatterjee, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

The nonlinear dynamics of a hybrid acousto-optic device was examined from the perspective of the Lyapunov exponent (LE) and bifurcation maps. The plots for LE versus system parameters and bifurcation maps have recently been examined against known simulation results including chaotic encryption experiments [1]. It is verified that the "loop gain" (feedback gain (β) times incident light amplitude (Iin) needs to be greater than one as a necessary , but not sufficient condition for the onset of chaos.

It is found that for certain combinations of β, Iin, net bias voltage (αtοt), and the initial value of the first-order scattered …

Monofilar Spiral Slot Antenna For Dual-Frequency Dual-Sense Circular Polarization, Xiulong Bao, Max Ammann

Articles

A dual-band antenna with right-hand circular polarization for the first frequency and the counter polarization at the second frequency is realized with compact printed spiral slots. The coupled spiral slots are fed by a 50 Ω microstrip line. Dual-sense circularly-polarized performance is achieved by realizing oppositely-directed current rotation for the two frequency bands. A parametric study shows that the additional slot significantly improves the bandwidth for both frequency bands. Measured results show that the fractional impedance bandwidth is greater than 18% for both bands. The 3 dB axial-ratio bandwidths are 4.5% and 3.5% for the RHCP and LHCP bands, respectively.

Wideband Dual-Frequency Dual-Polarized Dipole-Like Antenna, Xiulong Bao, Max Ammann

Articles

A wideband dual-frequency dual-polarized printed antenna is proposed for LTE, WLAN, and UWB systems. The dual-band antenna provides wide impedance bandwidths of 74% with respect to the center frequency of 2.725 GHz, and 39% with respect to the center frequency of 7.15 GHz. An open slot in the ground plane between the feed arms provides an orthogonal path to realize an embedded circularly polarized band at 2.35 GHz with an axial-ratio bandwidth of 16%. Dual-band characteristics are achieved by an asymmetrical dipole-like element and the coupling configuration between the T-shaped feed line and the wide ground-plane slot.

Wireless Passive Power Transfer Using Wire Antennas, Sheng Da Zhang

Electrical Engineering

This project tests and analyzes the efficiency of directional and omnidirectional antennas in wireless power transfer for charging. The project demonstrates the steps of construction and properties of dipole, monopole, and Yagi Uda antennas. A low power high frequency DC rectifier circuit converts the received RF power from the antenna and stored it as DC voltage on a capacitor. The receiver circuit also estimates the power received by the antenna. Wireless RF power transmission proves to be inefficient for short distances. The best efficiencies of the antennas were under 50% even at 0.1meter. The near field attenuation starts at around …

Cyber Physical Complex Networks, Modeling, Analysis, And Control, Neveen Shlayan

UNLV Theses, Dissertations, Professional Papers, and Capstones

This research scrutinize various attributes of complex networks; mainly, modeling, sensing, estimation, safety analysis, and control. In this study, formal languages and finite automata are used for modeling incident management processes. Safety properties are checked in order to verify the system. This method introduces a systematic approach to incident management protocols that are governed by mostly unsystematic algorithms. A portion of the used data in this study is collected by means of radar and loop detectors. A weighted t-statistics methodology is developed in order to validate these detectors. The detector data is then used to extract travel time information where …

Cyclostationary Detection For Ofdm In Cognitive Radio Systems, Marcos E. Castro

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Research on cognitive radio systems has attracted much interest in the last 10 years. Cognitive radio is born as a paradigm and since then the idea has seen contribution from technical disciplines under different conceptual layers. Since then improvements on processing capabilities have supported the current achievements and even made possible to move some of them from the research arena to markets.

Cognitive radio implies a revolution that is even asking for changes in current business models, changes at the infrastructure levels, changes in legislation and requiring state of the art technology.

Spectrum sensing is maybe the most important part …

Networks - Ii: A High Bandwidth Covert Channel In Network Protocol, Mehdi Hussain

International Conference on Information and Communication Technologies

Covert channel is secret communication path, which existence is not expected in original system of design. It allows different users access to the same information, at the same time, but from different points-of-view. It is being more and more studying due to the grooming of internet. Always high-bandwidth network covert channel pose the significant risk of detection over network. Although the existing technique utilized the reserved bits of header, timestamp, initial sequence number, packet length etc for network covert channel, to some extend these have good temper resistance. But when increase their covert data capacity they becomes to fail to …

Calibration Of Complex System Dynamics Models: A Practioner's Report, Rod Walker, Wayne Wakeland

Complex Systems Faculty Publications and Presentations

This paper is not a typical academic paper that is solidly grounded in the literature. Instead, this paper reports practitioner’s experiences in rebuilding and calibrating a very large system dynamics model. A prior version of this model had been in use for over 10 years in an ongoing executive training simulation. That model had never worked correctly in several key areas, requiring the outputs to be manually adjusted by very experienced facilitators during the course of the simulation. The present project rebuilt the system dynamics model, redesigned the parts that weren’t working, and calibrated the resulting model to match the …

San Luis Obispo Transit Tracker System Back-End Server, Daryl Alan A. Dimalanta

Computer Engineering

This document gives the rationale, design process, technical implementation, testing procedures, and testing results of a back-end server used for the San Luis Obispo (SLO) Transit Tracker System. The SLO Transit Tracker System (SLOTTS) includes client software installed on mobile devices and a back-end server. The purpose of this system is to encourage SLO residents to utilize the transit system by having the client software present current bus location, navigation instructions, and bus schedule in a simple, fast, and easy to use mobile application.

Due to the limited central processing unit (CPU) and limited power supplied by the battery, route …

Printed Circularly-Polarized Antenna With Ultra-Wide Axial-Ratio Bandwidth, Xiulong Bao, Max Ammann

Articles

A circularly polarised printed dipole-like antenna employing asymmetrical arms and an orthogonal slit in the ground plane is presented. It is fed by a stepped microstrip line which connects to the shorter arm. By utilising surface currents on the asymmetrical arms and the orthogonal feedline structure, circular polarisation is realised. Experimental and numerical data are in agreement and the measured results show a fractional impedance bandwidth of 41.3% (1.77–2.69 GHz) and a wide axial-ratio bandwidth of 38.4% (1.81–2.67 GHz).

An Investigation Into Ultrasonic Communication For Near-Body Networks, Eric Joshua Escudero Jr., Gursewak Singh Rai

Electrical Engineering

The following report presents a study of body-area, free-space ultrasonic communication system. Two analog communication systems are investigated. The initial communications system setup relies upon the amplitude modulation (AM) techniques to transmit the signal. Such a system is prone to noise since the amplitude of the signal is directly affected by distance and the signal strength will deteriorate. The secondary communication system involves utilizing frequency modulation (FM). This method avoids the issue of losing information due to amplitude deterioration, but encounters delay issues. The main hardware components used in the approach outlined include ultrasonic transducers (UTs) used for both transmitting …

Digital Modulations Using The Universal Software Radio Peripheral, Daniel Keith Artis

Electrical Engineering

Software defined radios (SDRs) are versatile systems that integrate hardware and software to create a reprogrammable wireless system.  Due to the versatility and hardware requirements of a SDR, they are typically expensive and not always affordable for educational institutions.  GNU Radio is a free software package that allows users to do signal processing on any computer using python and C++.  Using the Universal Software Radio Peripheral (USRP) board in conjunction with a standard personal computer (PC), a RF daughterboard, and the GNU Radio software, we can create a software defined radio that can transmit, receive, and process signals.  Because the …

Wirelessly Operated Pa Loudspeaker System For Rmax Search-And-Rescue Uav: A Preliminary Design, Travis Luke, Nolan Uchizono

Electrical Engineering

This paper discusses the approach used to implement a wireless PA loudspeaker system on a search-and-rescue RMAX UAV.

The purpose of this project is to allow the continuation of communication between search-and-rescue workers as well as potential rescuees in an environment that won't always allow it. Since rugged terrain tends to cause interference between two radio communications, there needs to be a way to bypass this problem. In addition, people in need of rescue are unlikely to be using a radio on an emergency frequency, so there needs to be a way to efficiently issue orders or evacuation notices without …

Laser Cursor, Michael Liman

Electrical Engineering

A user controls a cursor on a computer screen using a laser pointer.  A camera picks up the laser pointer’s position and sends the data to the computer to move the cursor in the correct position.

Discrete Alarm Clock, Travis Moore, Collin Barth

Electrical Engineering

The standard alarm clock, as used daily by millions worldwide, has clear room for modification and improvement.  This paper documents an implementation that rectifies many of these flaws.  Improvements include adjustable snooze length, an IR remote for ease of use, and an RF headset for discrete alarm use or potential incorporation into a device much like a hearing aid.  The processes involved in creating a digital alarm clock, as well as the obstacles met in the implementation of the enhanced design, are detailed within.

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments.  There is good reason for this, too.  In the State of California, office buildings represent the single largest user of energy in the commercial sector.  This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations.  The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

A Neural Network Receiver For Em-Mwd Communication, Timothy P. Whitacre

Master's Theses

Baseband digital communication in electro-magnetic measurement while drilling (EM-MWD) systems is often corrupted by non-white surface noise. The inability to reliably decode the transmitted signals in a noisy environment limits the depth at which EM-MWD systems can operate. Correlation receivers, which are optimal in the presence of additive white Gaussian noise, can be sub-optimal in the presence of various types of field noise at different drilling sites.

This thesis investigates the application of artificial neural networks (ANN) as communication receivers in EM-MWD baseband digital communication systems. The performances of various ANN architectures and training algorithms are studied and compared with …

Underwater Localization And Tracking Of Physical Systems, Patrick E. Carroll

Master's Theses

In this paper, we investigate the problem of localizing an underwater sensor node basedon message broadcasting from multiple surface nodes. With the time-of-arrival measurementsfrom a DSP-based multicarrier modem, each sensor node localizes itself based on the traveltime differences among multiple senders to the receiver. Using one-way message passing, such asolution can scale to accommodate a large number of nodes in a network. We consider the issuefrom not only the physical layer, but also at the node processing layer by incorporating a trackingsolution. We present simulation results as well as preliminary testing results in a swimming poolwith both stationary and moving …