Systems and Communications Commons^™

Design And Verification Of A Labview Automated Antenna Radiation Pattern Measurement System, Dylan C. Bloom

Master's Theses

In 2014, Toyon Research Corporation donated a 6’x6’x8’ anechoic chamber to the Cal Poly EE department to advance student education in the areas of antennas and wireless communications. An anechoic chamber is a room designed to suppress electromagnetic radiation reflections so that accurate measurement of radio frequency (RF) systems such as wireless radios and antennas can take place. Despite the fact that Cal Poly already has a larger anechoic chamber, primarily used for antenna characterization, it is the purpose of this project to design, code, and equip the new chamber so that it performs at least as good, or better …

Rf Front End For An Integrated Silhouette Capture And Boundary Detection Frequency Modulated Continuous Wave Ultra-Wideband Radar System For The Extension Of Independent Living, Adrian Smet

Master's Theses

Limitations of current eldercare monitoring systems leave a need for new solutions. A monitoring system based on a frequency modulated continuous wave ultra-wideband short-range radar is proposed for this application. The complete proposed monitoring system is comprised of four blocks: boundary detection, silhouette capture, human identification, and data transmission. This paper develops the RF front end hardware for the silhouette capture subsystem.

System requirements are derived for the silhouette capture subsystem. An architecture for the RF front end is designed, and required individual component specifications are determined. Components are selected off the shelf or custom designed for each socket. Full …

Verification Of Receiver Equalization By Integrating Dataflow Simulation And Physical Channels, David M. Ritter, Tina Smilkstein

Master's Theses

This thesis combines Keysight’s SystemVue software with a Vector Signal Analyzer (VSA) and Vector Signal Generator (VSG) to test receiver equalization schemes over physical channels. The testing setup, “Equalization Verification,” is intended to be able to evaluate any equalization scheme over any physical channel, and a decision-directed feed-forward LMS equalizer is used as an example. The decision-directed feed-forward LMS equalizer is shown to decrease the BER from 10^-2 to 10^-3 (average of all trials) over a CAT7 and CAT6A cable, both simulated and physical, for 1GHz and 2GHz carrier, and 80MHz data rate. A wireless channel, 2.4GHz Dipole …

Complex Filters As Cascade Of Buffered Gingell Structures: Design From Band-Pass Constraints, Nicole M. Hay

Master's Theses

Complex filters are multi-input, multi-output networks designed to discriminate based upon the relative phase difference between input signals. Complex filters find application in modern wireless systems for single sideband transmission and image-reject reception. This thesis presents one active complex filter implementation using two operational amplifiers per stage, termed “type-II” topology. The “type-II” originates from the passive RC-CR polyphase topology presented by Gingell in his 1973 paper, “Single sideband modulation using sequence asymmetric polyphase networks.” This new topology gains several advantages over existing complex filter implementations, namely “cascadability” (multiple sections placed in series to create a higher-order response) without altering the …

Estimating Transit Ridership Patterns Through Automated Data Collection Technology: A Case Study In San Luis Obispo, California, Ashley Kim

Master's Theses

Public transportation offers a crucial solution to the travel demand in light of national and global economic, energy, and environmental challenges. If implemented effectively, public transit offers an affordable, convenient, and sustainable transportation mode. Implementation of new technologies for information-harvesting may lead to more effective transit operations. This study examines the potential of automated data collection technologies to analyzing and understand the origin-destination flow patterns, which is essential for transit route planning and stop location placement.

This thesis investigates the collection and analysis of data of passengers onboard San Luis Obispo Transit buses in February and March 2017 using Bluetooth …

Uhf Rfid Antenna Impedance Matching Techniques, Kamron Sockolov

Master's Theses

Radio Frequency Identification (RFID) systems use electromagnetic signals to wirelessly identify and track RFID-tagged objects. A reader transmits a carrier wave request signal to an RFID tag, which then transmits a unique identification signal back to the reader. Applications include supply chain inventory management, automated toll booth fee systems, sports event timing, restricted access control, pet monitoring and retail theft prevention. An RFID tag includes an antenna connected to a Radio Frequency Integrated Circuit (RFIC). RFID tags in the ultra-high frequency (UHF), industrial, scientific and medical (ISM) 902-928MHz band and global Electronic Product Code (EPC) 860‑960MHz band are powered passively …

Thermal Evolution Of Moon, Arshdeep Singh Gill

Master's Theses

In August, 2014 three experiments were conducted using infrared systems deployed at White Mountain Research center, CA. The data was acquired for the whole month of August. Teams of 3-4 students from Cal Poly San Luis Obispo and UC Santa Barbara were stationed at the research center for 2-3 days to operate the equipment. The three experiments were:(1) creating spatial-temporal time series of lunar surface temperatures;(2) identifying atmospheric meteor trails;(3) search for meteor impacts on the Moon surface. Out of the three this thesis focusses on experiment 1 and the results from this experiment could also help with the other …

Scaled Synthetic Aperture Rader Development, Jason Garvey Schray

Master's Theses

Several previous Cal Poly thesis projects involve synthetic aperture radar (SAR), automatic target recognition (ATR), and tracking. SAR data was either accessed from a publicly available database or generated using complex computer modeling software. The motivation for this dual thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Ideally this is a low-cost, high resolution SAR architecture that produces raw range Doppler data for any desired target area. To that end, a scaled SAR system was successfully designed, built, and tested. The current SAR system, however, does not perform azimuthal compression and …

Analysis Of Various Algorithmic Approaches To Software-Based 1200 Baud Audio Frequency Shift Keying Demodulation For Aprs, Robert F. Campbell

Master's Theses

Digital communications continues to be a relevant Field of study as new technologies appear and old methodologies get revisited or renovated. The goal of this research is to look into the old digital communication scheme of Bell 202 [67] used by APRS and improve software based demodulation performance. Improved performance is defined by being able to correctly decode more packets in an efficient, real time, manner. Most APRS demodulation is currently done using specialized hardware since that yields the best performance. This research shows that through using Sivan Toledo's javAX25 [72] software package, new demodulation algorithms can be implemented that …

Scaled Synthetic Aperture Radar System Development, Ryan K. Green

Master's Theses

Synthetic Aperture Radar (SAR) systems generate two dimensional images of a target area using RF energy as opposed to light waves used by cameras. When cloud cover or other optical obstructions prevent camera imaging over a target area, SAR can be substituted to generate high resolution images. Linear frequency modulated signals are transmitted and received while a moving imaging platform traverses a target area to develop high resolution images through modern digital signal processing (DSP) techniques. The motivation for this joint thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Objectives include …

Design And Fabrication Techniques Of Devices For Embedded Power Active Contact Lens, Errol Heradio Leon

Master's Theses

This thesis designed and fabricated various devices that were interfaced to an IC for an active contact lens that notifies the user of an event by detection of an external wireless signal. The contact lens consisted of an embedded antenna providing communication with a 2.4GHz system, as well as inductive charging at an operating frequency of 13.56 MHz. The lens utilized a CBC005 5µAh thin film battery by Cymbet and a manufactured graphene super capacitor as a power source. The custom integrated circuit (IC) was designed using the On Semiconductor CMOS C5 0.6 µm process to manage …

Synthetic Aperture Radar: Rapid Detection Of Target Motion In Matlab, Daniel S. Kassen

Master's Theses

Synthetic Aperture Radar (SAR) has come into widespread use in several civilian and military applications. The focus of this paper is the military application of imaging point targets captured by an airborne SAR platform. Using the traditional SAR method of determining target motion by analyzing the difference between subsequent images takes a relatively large amount of processing resources. Using methods in this thesis, target motion can be estimated before even a single image is obtained, reducing the amount of time and power used by a significantly large amount. This thesis builds on work done by Brain Zaharri and David So. …

Hybrid Silicon Mode-Locked Laser With Improved Rf Power By Impedance Matching, Bassem M. Tossoun

Master's Theses

The mode-locked laser diode (MLLD) finds a lot of use in applications such as ultra high-speed data processing and sampling, large-capacity optical fiber communications based on optical time-division multiplexing (OTDM) systems. Integrating mode-locked lasers on silicon makes way for highly integrated silicon based photonic communication devices. The mode-locked laser being used in this thesis was built with Hybrid Silicon technology. This technology, developed by UC Santa Barbara in 2006, introduced the idea of wafer bonding a crystalline III- V layer to a Silicon-on-insulator (SOI) substrate, making integrated lasers in silicon chips possible.

Furthermore, all mode-locked lasers produce phase noise, which …

Data Chunking In Quasi-Synchronous Ds-Cdma, Trevor Dalke

Master's Theses

DS-CDMA is a popular multiple access technique used in many mobile networks to efficiently share channel resources between users in a cell. Synchronization between users maximizes the user capacity of these systems. However, it is difficult to perfectly synchronize users in the reverse link due to the geographic diversity of mobile users in the cell. As a result, most commercial DS-CDMA networks utilize an asynchronous reverse link resulting in a reduced user capacity. A possible compromise to increase the user capacity in the reverse link is to implement a quasi-synchronous timing scheme, a timing scheme in which users are allowed …

A Compact, Reconfigurable Uhf Communication System Design For Use With Polysat's Embedded Linux Platform, Austin Williams

Master's Theses

The beginning of this thesis provides an overview of the heritage UHF Communication System design flown on CP2, CP3, CP4, CP5, and CP6, summarizing previous analysis of its performance, and providing the justification for a complete system re-design. High level requirements for the new UHF System are defined, and a trade study is performed on state-of-the-art single chip transceivers, low noise amplifiers, and transmit power amplifiers. These components are then designed into a functional communication system, with key components analyzed for proper impedance matching and performance characterization compared to expected datasheet values. Next, the system as a whole is characterized …

A Novel Unit Cell Antenna For Highly Integrated Phased Arrays In The Shf Band, Timothy Bryan Ogilvie

Master's Theses

Phased arrays are electromagnetic antenna systems comprised of many radiating elements and processing electronics. Radiating elements are typically positioned in an orderly grid within the antenna aperture. In the receive mode of operation, radiating elements capture some of the signal energy from incoming radiation and guide these signals to processing electronics. Signals are filtered and amplified to maintain the desired sensitivity and complexly weighted using circuits with reconfigurable amplification gain and phase delay. Finally, all signals are combined. The summation of these complexly weighted spatial samples forms a spatial filter in the same way complexly weighted temporal samples establish a …

Radio Direction Finding Network Receiver Design For Low-Cost Public Service Applications, Marcel Colman Eric Stieber

Master's Theses

A low-cost radio direction finding (RDF) VHF receiver has been investigated for development into a radio direction finding network (RDFN) with a particular focus towards public service and commercial asset tracking applications. The primary design criteria were reproducibility, low-cost, and simplicity such that public service and volunteer organizations can benefit from the technology. Two receiver designs were built and tested to allow for comparison of practicality, cost, and accuracy. A pseudo-Doppler RDF and a time difference of arrival (TDOA) receiver were built as proof-of-concept for a system design based on commercial off-the-shelf (COTS) components. The pseudo-Doppler system is a less …

Noise Reduction With Microphone Arrays For Speaker Identification, Zachary Gideon Cohen

Master's Theses

The presence of acoustic noise in audio recordings is an ongoing issue that plagues many applications. This ambient background noise is difficult to reduce due to its unpredictable nature. Many single channel noise reduction techniques exist but are limited in that they may distort the desired speech signal due to overlapping spectral content of the speech and noise. It is therefore of interest to investigate the use of multichannel noise reduction algorithms to further attenuate noise while attempting to preserve the speech signal of interest.

Specifically, this thesis looks to investigate the use of microphone arrays in conjunction with multichannel …

Constant Conduction Angle Biasing For Class C Monolithic Rf Power Amplifiers, Gursewak Singh Rai

Master's Theses

In modern wireless communication systems, a base station typically serves a few hundred users within its cell coverage. To combat the near-far problem – the situation where a nearby user’s strong cellular signal masks the cellular signal of a faraway user – base stations continually enforce power control. That is, nearby users must lower their transmit power. In CDMA technology, power control can be as large as 70-80dB. At low power outputs, this greatly impacts the performance of the RF power amplifier (PA) in the cellular device. For small RF drives, the magnitude of the output RF current approaches the …

Development And Implementation Of A Calibration Procedure For Complex Impedance Spectrum Measurements With Applications To Embedded Battery Health Monitoring And Management Systems, William H. Morrison

Master's Theses

Energy storage devices such as rechargeable Lithium ion batteries are assuming an increasingly prominent role in society, covering applications from electric / hybrid electric vehicles to personal portable electronics. In response to this increasing demand, technologies that monitor battery health and remaining useful life have developed. One such system is the Smart Battery Status Monitor (SBSM), developed by the Idaho National Laboratory, Montana Tech and Qualtech Systems, Inc. The SBSM utilizes impedance spectrum measurements using a subsystem called the Impedance Measurement Box (IMB). The impedance measurements are complex quantities (having both a resistive and a reactive component) and are made …

Active Storage And Ssd Caching In An Object Storage Environment, Michael T. Runde

Master's Theses

The advancing performance and lowering costs required to implement additional processing power on system peripherals such as disk drives are increasingly allowing additional computing ability to be located directly on individual drives. Active Storage attempts to take advantage of this excess by moving some computationally intensive applications directly to the disk drives. This can remove the bottlenecks seen through interconnects between the drives and the CPU of an initiating system as well as remove the need for systems to handle these applications.

The contributions of this thesis are in two areas. The first is the development of a framework designed …

Linear Power-Efficient Rf Amplifier With Partial Positive Feedback, Matthew E. King

Master's Theses

Over the last decade, the number of mobile wireless devices on the market has increased substantially. New “multi-carrier” modulation schemes, such as OFDM, WCDMA, and WiMAX, have been developed to accommodate the increasing number of wireless subscribers and the demand for faster data rates within the limited commercial frequency spectrum. These complex modulation schemes create signals with high peak-to-average power ratios (PAPR), exhibiting rapid changes in the signal magnitude. To accommodate these high-PAPR signals, RF power amplifiers in mobile devices must operate under backed-off gain conditions, resulting in poor power efficiency. Various efficiency-enhancement solutions have been realized for backed-off devices …

Spectral Shape Division Multiplexing (Ssdm): Apparatus, Transmitter, Receiver And Detection, Fausto Daniel Holguín-Sánchez

Master's Theses

Wireless communication companies require to use the frequency spectrum to operate. Both frequency licenses and infrastructure to reuse frequencies are costly resources subject to increasing demand. This work introduces a novel multiplexing method that saves spectrum called Spectral Shape Division Multiplexing (SSDM). Under certain configurations, SSDM displays higher flexibility and throughput than other spectrally efficient methods.

SSDM defines the structure of a wireless multi-carrier by software. It is similar to Orthogonal Frequency Division Multiplexing (OFDM) in that both use overlapped sub-carriers to make efficient use of allocated spectrum. However, SSDM has several advantages. Where OFDM organizes sub-carriers orthogonally, SSDM allows …

Computational Modeling For Transportation Network Security, Sherif A. Tolba

Master's Theses

No abstract provided.

A Neural Network Receiver For Em-Mwd Communication, Timothy P. Whitacre

Master's Theses

Baseband digital communication in electro-magnetic measurement while drilling (EM-MWD) systems is often corrupted by non-white surface noise. The inability to reliably decode the transmitted signals in a noisy environment limits the depth at which EM-MWD systems can operate. Correlation receivers, which are optimal in the presence of additive white Gaussian noise, can be sub-optimal in the presence of various types of field noise at different drilling sites.

This thesis investigates the application of artificial neural networks (ANN) as communication receivers in EM-MWD baseband digital communication systems. The performances of various ANN architectures and training algorithms are studied and compared with …

Underwater Localization And Tracking Of Physical Systems, Patrick E. Carroll

Master's Theses

In this paper, we investigate the problem of localizing an underwater sensor node basedon message broadcasting from multiple surface nodes. With the time-of-arrival measurementsfrom a DSP-based multicarrier modem, each sensor node localizes itself based on the traveltime differences among multiple senders to the receiver. Using one-way message passing, such asolution can scale to accommodate a large number of nodes in a network. We consider the issuefrom not only the physical layer, but also at the node processing layer by incorporating a trackingsolution. We present simulation results as well as preliminary testing results in a swimming poolwith both stationary and moving …

Aperture Coupled Microstrip Antenna Design And Analysis, Michael Paul Civerolo

Master's Theses

A linearly-polarized aperture coupled patch antenna design is characterized and optimized using HFSS antenna simulation software. This thesis focuses on the aperture coupled patch antenna due to the lack of fabrication and tuning documentation for the design of this antenna and its usefulness in arrays and orthogonally polarized communications. The goal of this thesis is to explore dimension effects on aperture coupled antenna performance, to develop a design and tuning procedure, and to describe performance effects through electromagnetic principles.

Antenna parameters examined in this study include the dimensions and locations of the substrates, feed line, ground plane coupling slot, and …

Negative Conductance Load Modulation Rf Power Amplifier, Cody R. Neslen

Master's Theses

The number of mobile wireless devices on the market has increased substantially over the last decade. The frequency spectrum has become crowded due to the number of devices demanding radio traffic and new modulation schemes have been developed to accommodate the number of users. These new modulation schemes have caused very poor efficiencies in power amplifiers for wireless transmission systems due to high peak-to-average power ratios (PAPR). This thesis first presents the issue with classical power amplifiers in modern modulation systems. A brief overview of current attempts to mitigate this issue is provided. A new RF power amplifier topology is …

Modular Laser Combat System For Remotely Operated Vehicles: Bridging The Gap Between Computer Simulation And Live Fire, Thomas Edward Fulenwider

Master's Theses

In the emerging industry of small unmanned vehicles, pioneered by small businesses and research institutions, a suitable combat system test platform is needed. Computer simulations are useful, but do not provide the definitive proof of effective operation necessary for deployment of a combat system. What is needed is an affordable simulated weapons system that enables live flight testing without the used of live weaponry.

A framework is developed here for the construction of a simulated weapon using Free Space Optical (FSO) infrared communication. It is developed in such a way to ensure compatibility with a variety of platforms including ground …

A Constant Conduction Angle Biased Rf Power Amplifier For Improved Linearization In Class C Operation, Greg Lacaille

Master's Theses

Class C power amplifiers offer higher efficiency than class B power amplifiers, but suffer from poor linearity. A feedback based biasing system to improve the linearity of a class C power amplifier is designed. A class B amplifier with a gain of 20 dB and 20 MHz bandwidth at 900 MHz acts as the launching point for the design. The biasing and output network of the class B power amplifier is modified to produce a class C amplifier at conduction angles of 180°, 162°, 126°, 90°, and 54°. A feedback based biasing system, which uses two matched and scaled down …