Signal Processing Commons^™

The Design And Analysis Of Robust Mems Devices For Extreme Space Environments, Joshua Taggart

Honors Undergraduate Theses

The purpose of this study is to analyze aluminum nitride (AlN) micro-electromechanical systems (MEMS) resonators designed for extreme-environment applications. The devices of study are Lamb wave, piezoelectric resonators designed and fabricated using conventional semiconductor manufacturing processes and operating around various frequencies in the megahertz range. The purpose of this study is to advance understanding of MEMS devices in extreme-temperature and radiated environments for outer-space applications.

Devices were tested under vacuum at temperatures ranging from room temperature (~21°C) to 800°C. Under these conditions, the device was measured both as a resonator and in an oscillator circuit. Results show that the resonant …

Piezoelectric Actuator Driver System, Daniel Hoefer

Electrical Engineering

This work presents the design, fabrication, and testing of a high-voltage piezoelectric actuator driver system purposed for integration into defense and aerospace precision motion control applications, particularly those in laser optics. The core challenge addressed was the mismatch between the standardized 28V DC power bus used in military systems and the significantly higher voltage requirements of piezoelectric actuators. Existing commercial drivers were evaluated and found unsuitable for field deployment due to inadequate ruggedness, excessive complexity, or power limitations. Consequently, a modular system architecture was designed featuring four independent driver channels, each using a high-voltage, high-current linear amplifier topology to scale …

Design And Fabrication Of A Low Power 7.2 Terabit Transmitter For Exascale Computing, Scott Mcwilliams

Electrical Engineering Theses and Dissertations

Enhanced Coupled Strength (ECS) gratings fabricated into III-V based devices offer high reflected power per unit length and broad band reflectivity as compared to conventional 1st order gratings, desired qualities for short-haul high speed transmitters that can be implemented without the need for chip-level temperature control, contributing to the low power per transmitted bit. For commercial DBR lasers, the grating reflectivity results in an extremely narrow reflectivity spectrum, which is highly desired for most/many applications, but requires a power hungry thermo-electric cooler to maintain a fixed frequency. The proposed LEAM (laser electro-absorption modulator) requires a broad reflectivity spectrum, which, by …

Improving Cellphone-Based Bio-Imaging Technique For Fluorescence Detection, Erteza T. Efaz

LSU Master's Theses

The research presented in this thesis focuses on the design, development, and evaluation of a fluorescence detection system. The system is implemented primarily as an Android application, Auto Camera, which leverages smartphone cameras to capture and analyze fluorescent images. The application provides a user-friendly interface with some configurable features like exposure time, ISO speed, and storage limit; as well as defining detection thresholds and setting acquisition intervals. This study begins with the architectural framework of the Android application, which is written in Java using Android Studio. The API compatibility is set to version 33, and users are prompted to grant …

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

Experimental And Computational Analysis Of Broadband Thz Photoconductive Antennas, Zachary Uttley, Jose Santos Batista, Bilal Pirzada, Magda El-Shenawee

Electrical Engineering Faculty Publications and Presentations

The work presents the fabrication and measurements of four LT-GaAs photoconductive terahertz (THz) antennas with different geometries of metallic electrodes. The goal is to analyze the overall bandwidth of the antennas through a comparison between the spectra of the generated photocurrent in the antenna gap, the radiated electric field THz pulse, and the S₁₁ parameter of the metallic electrodes. The photocurrent density and the S₁₁ parameters are computed using COMSOL multiphysics, while the generated THz pulse was experimentally measured using a time-domain spectroscopy system. The polarizations of the photoconductive antennas are experimentally measured, using x-cut quartz crystal halfwave …

Design & Analysis Of Mixed-Mode Integrated Circuit For Pulse-Shape Discrimination, Bryan Orabutt

McKelvey School of Engineering Graduate Student Theses & Dissertations

In nuclear science experiments it is usually necessary to determine the type of radiation, its energy and direction with considerable accuracy. The detection of neutrons and discriminating them from gamma rays is particularly difficult. A popular method of doing so is to measure characteristics intrinsic to the pulse shape of each radiation type in order to perform pulse-shape discrimination (PSD).

Historically, PSD capable systems have been designed with two approaches in mind: specialized analog circuitry, or digital signal processing (DSP). In this work we propose a PSD capable circuit topology using techniques from both the analog and DSP domains. We …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

The Effects Of The Transient And Performance Loss Rates On Pv Output Performance, Chibuisi Chinasaokwu Okorieimoh, Brian Norton, Michael Conlon

Conference papers

Solar photovoltaic (PV) panels experience long-term performance degradation as compared to their initial performance, resulting in lower like-per-like efficiencies and performance ratios. Manufacturers of solar photovoltaic modules normally guarantee a lifespan of more than 20 years. To meet such commitments, it is important to monitor and mitigate PV module degradation during this period, as well as beyond, to recognize maintenance and repair needs. Solar PV modules degrade over time, becoming less effective, less reliable, and eventually unusable. The effects of transient and performance loss rates on the output performance of polycrystalline silicon (p-Si) solar PV modules are the focus of …

Optoelectronic Valley-Spin Qubits With Ambipolar Quantum Dots, Jeremy Tull

Electrical Engineering Undergraduate Honors Theses

The current limitations of qubit-based processors are caused by imperfections in quantum gates, leading to a lack of gate fidelity. Gate fidelity can be refined by extending the coherence of qubits and reducing logic operation speed. A potential solution is to develop a hybrid qubit that has the coherence of electrically-controlled quantum dots and the gate speed of their optically-controlled counterparts. Quantum bits that utilize ultrafast optical gating to perform gate operations require precise control of the gating pulse duration. Optical dispersion can cause adverse effects pulse duration, such as pulse broadening, so dispersion-compensation techniques must be employed; by properly …

Technique Design Of Filter On Surface-Acoustic Waves, Dilmurod Abdujalilovich Davronbekov, Zafar Tulyaganovich Khakimov

Acta of Turin Polytechnic University in Tashkent

The article describes the design of filters on surface acoustic waves (SAWs), which are selective elements and are widely used in blocks, devices and signal processing systems in telecommunications, including wireless communication systems such as cellular, trunking and others. Designs of filters for surfactants are considered, which are divided into two large groups - by functional purpose and by a systematic approach to the synthesis of performance characteristics of filters for surfactants. Optimization algorithms and methods for synthesizing surfactant filters have been developed and improved. An improved technique for the synthesis of a filter based on surface acoustic waves is …

An Exploratory Study Of Pulse Width And Delta Sigma Modulators, Logan B. Penrod

Master's Theses

This paper explores the noise shaping and noise producing qualities of Delta-Sigma Modulators (DSM) and Pulse-Width Modulators (PWM). DSM has long been dominant in the Delta Sigma Analog-to-Digital Converter (DSADC) as a noise-shaped quantizer and time discretizer, while PWM, with a similar self oscillating structure, has seen use in Class D Power Amplifiers, performing a similar function. It has been shown that the PWM in Class D Amplifiers outperforms the DSM [1], but could this advantage be used in DSADC use-cases? LTSpice simulation and printed circuit board implementation and test are used to present data on four variations of these …

Hybrid Microwave Power Amplifiers For Broadband Communication, Sangaran Pragash

Student Works (2020-2029)

The software-defined radio is the future of radio technology. The development of a broadband power amplifier is the most challenging radio component to design in achieving software-defined radio goals due to the PA gain-bandwidth limitation. The distributed power amplifier (DPA) overcomes the limitation by combining output power from several transistors in an additive fashion. Matrix Amplifier (MA) consists of two or more DPA stacked together in a multiplicative manner. In this project, a high power and high gain DPA for a two-way radio system is demonstrated. The DPA exhibits 10W output power and 32dB gain across the frequency range of …

A Silicon Germanium Cmos Linear Voltage Regulator For Wireless Agricultural Applications, Aminta Naidili Castillo Robles

Graduate Theses and Dissertations

This thesis presents the design, simulation and test results of a silicon germanium (SiGe) complementary metal-oxide-semiconductor (CMOS) linear regulator. The objective of the circuit is to power other analog devices regardless of the load current and input voltage changes. The application of this regulator is to be part of a project developing a miniaturized semiconductor platform that can be inserted into stems of crops in order to measure data inside the plant and then send it wirelessly to the user. The linear regulator was designed on a BiCMOS SiGe 0.13µm which is a GlobalFoundries process. It has been tested at …

Investigating The Effect Of Detecting And Mitigating A Ring Oscillator-Based Hardware Trojan, Lakshmi Ramakrishnan

Electrical Engineering Theses and Dissertations

The outsourcing of the manufacturing process of integrated circuits to fabrications plants all over the world has exposed these chips to several security threats, especially at the hardware level. There have been instances of malicious circuitry, such as backdoors, being added to circuits without the knowledge of the chip designers or vendors. Such threats could be immensely powerful and dangerous against confidentiality, among other vulnerabilities.

Defense mechanisms against such attacks have been probed and defense techniques have been developed. But with the passage of time, attack techniques have improved immensely as well. From directly observing the inputs or outputs, adversaries …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

An Exact Analysis For Four-Order Acousto-Optic Bragg Diffraction Which Incorporates Both Incident Light Angle And Sound Frequency Dependencies, Adeyinka Sunday Ademola

Electrical Engineering Theses

This thesis extends the prior work which produced an exact solution to the four-order acousto-optic (AO) Bragg cell with assumed fixed center frequency and with exact Bragg angle incident light. The extension predicts the model that incorporates the dependencies of both the input angle of light and the sound frequency. Specifically, a generalized 4^th order linear differential equation (DE), is developed from a simultaneous analysis of four coupled AO system of DEs. Through standard methods, the characteristic roots, which requires solving a quartic equation, is produced. Subsequently, a derived system of homogeneous solutions, which absorbs the roots obtained using …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Chipper: Capacitive Bed Occupancy Sensing For An Intelligent Alarm Clock, David Levi

Electrical Engineering

What if your alarm clock knew when you got out—and stayed out—of bed? Current alarm clocks happily let you go back to bed after turning them off. In this project, I build an alarm which only stops ringing when you get out bed, and starts ringing again if you lie back in bed.

This project uses capacitance to detect bed occupancy. A person on or near the bed creates a tiny, picofarads level increase in capacitance, as seen by a sensor placed under the mattress. A microprocessor interprets this signal, and also drives an audio alarm. Shielding of the sensor …

Low Voltage Cmos Sar Adc Design, Ryan Hunt

Electrical Engineering

This project centers on the design of a single ended 10-bit successive approximation register analog to digital converter (SAR ADC for short) that easily interfaces to a micro-controller, such as an Arduino. With micro-controller interfacing in mind, the universal data transfer technique of SPI proved an easy way to communicate between the ADC and the micro-controller. The ADC has a range of 1V (highest code value) to 0V (lowest code value) and operates from a single voltage rail value of 1.8V. Typical SPI clock speeds run on the order of 2MHz and with a 10-bit ADC this means a sampling …

Max Operation In Statistical Static Timing Analysis On The Non-Gaussian Variation Sources For Vlsi Circuits, Abu M. Baker

UNLV Theses, Dissertations, Professional Papers, and Capstones

As CMOS technology continues to scale down, process variation introduces significant uncertainty in power and performance to VLSI circuits and significantly affects their reliability. If this uncertainty is not properly handled, it may become the bottleneck of CMOS technology improvement. As a result, deterministic analysis is no longer conservative and may result in either overestimation or underestimation of the circuit delay. As we know that Static-Timing Analysis (STA) is a deterministic way of computing the delay imposed by the circuits design and layout. It is based on a predetermined set of possible events of process variations, also called corners of …

Understanding Vehicular Traffic Behavior From Video: A Survey Of Unsupervised Approaches, Brendan Tran Morris, Mohan Manubhai Trivedi

Electrical & Computer Engineering Faculty Research

Recent emerging trends for automatic behavior analysis and understanding from infrastructure video are reviewed. Research has shifted from high-resolution estimation of vehicle state and instead, pushed machine learning approaches to extract meaningful patterns in aggregates in an unsupervised fashion. These patterns represent priors on observable motion, which can be utilized to describe a scene, answer behavior questions such as where is a vehicle going, how many vehicles are performing the same action, and to detect an abnormal event. The review focuses on two main methods for scene description, trajectory clustering and topic modeling. Example applications that utilize the behavioral modeling …

Automated Channel Assessment For Single Chip Medradio Transceivers, Mark Alexander Hillig

Dissertations and Theses

Modern implantable and body worn medical devices leverage wireless telemetry to improve patient experience and expand therapeutic options. Wireless medical devices are subject to a unique set of regulations in which monitoring of the available frequency spectrum is a requirement. To this end, implants use software protocols to assess the in-band activity to determine which channel should be used. These software protocols take valuable processing time and possibly degrade the operational lifetime of the battery. Implantable medical devices often take advantage of a single chip transceiver as the physical layer for wireless communications. Embedding the channel assessment task in the …

Multi-Mode Self-Referencing Surface Plasmon Resonance Sensors, Jing Guo

Theses and Dissertations--Electrical and Computer Engineering

Surface-plasmon-resonance (SPR) sensors are widely used in biological, chemical, medical, and environmental sensing. This dissertation describes the design and development of dual-mode, self-referencing SPR sensors supporting two surface-plasmon modes (long- and short-range) which can differentiate surface binding interactions from bulk index changes at a single sensing location. Dual-mode SPR sensors have been optimized for surface limit of detection (LOD). In a wavelength interrogated optical setup, both surface plasmons are simultaneously excited at the same location and incident angle but at different wavelengths. To improve the sensor performance, a new approach to dual-mode SPR sensing is presented that offers improved differentiation …

Estimation Of Performance Indices For The Planning Of Sustainable Transportation Systems, Alexander Paz, Pankaj Maheshwari

Electrical & Computer Engineering Faculty Research

In the context of sustainable transportation systems, previous studies have either focused only on the transportation systemor have not used a methodology that enables the treatment of incomplete, vague, and qualitative information associated with the available data. This study proposes a system of systems (SOS) and a fuzzy logic modeling approach. The SOS includes the Transportation, Activity, and Environment systems. The fuzzy logic modeling approach enables the treatment of the vagueness associated with some of the relevant data. Performance Indices (PIs) are computed for each system using a number of performance measures. The PIs illustrate the aggregated performance of each …

Laser Cursor, Michael Liman

Electrical Engineering

A user controls a cursor on a computer screen using a laser pointer.  A camera picks up the laser pointer’s position and sends the data to the computer to move the cursor in the correct position.

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Application Of Signal Advance Technology To Electrophysiology, Chris M. Hymel

Dissertations and Theses (Open Access)

Medical instrumentation used in diagnosis and treatment relies on the accurate detection and processing of various physiological events and signals. While signal detection technology has improved greatly in recent years, there remain inherent delays in signal detection/ processing. These delays may have significant negative clinical consequences during various pathophysiological events. Reducing or eliminating such delays would increase the ability to provide successful early intervention in certain disorders thereby increasing the efficacy of treatment.

In recent years, a physical phenomenon referred to as Negative Group Delay (NGD), demonstrated in simple electronic circuits, has been shown to temporally advance the detection of …

Hand-Held Flyback Driven Coaxial Dielectric Barrier Discharge: Development And Characterization, Victor J. Law, Vladimir Milosavljevic, Neil O’Connor, James F. Lalor, Steven Daniels

Articles

The development of a handheld single and triple chamber atmospheric pressure coaxial dielectric barrier discharge driven by Flyback circuitry for helium and argon discharges is described. The Flyback uses external metal-oxide-semiconductor field-effect transistor power switching technology and the transformer operates in the continuous current mode to convert a continuous dc power of 10–33 W to generate a 1.2–1.6 kV 3.5 μs pulse. An argon discharge breakdown voltage of ∼768 V is measured. With a 50 kHz, pulse repetition rate and an argon flow rate of 0.5–10 argon slm (slm denotes standard liters per minute), the electrical power density deposited in …

Real-Time Plasma Controlled Chemistry In A Two-Frequency, Confined Plasma Etcher, Vladimir Milosavljevic, Albert R. Ellingboe, Cezar Gaman, John V. Ringwood

Articles

The physics issues of developing model-based control of plasma etching are presented. A novel methodology for incorporating real-time model-based control of plasma processing systems is developed. The methodology is developed for control of two dependent variables (ion flux and chemical densities) by two independent controls (27 MHz power and O2flow). A phenomenological physics model of the nonlinear coupling between the independent controls and the dependent variables of the plasma is presented. By using a design of experiment, the functional dependencies of the response surface are determined. In conjunction with the physical model, the dependencies are used to deconvolve the sensor …