Power and Energy Commons^™

Three-Dimensional Porous Vn Octahedron Catalyst With High Electrocatalytic Efficiency Toward Hydrogen Evolution Reaction, Can Yin, Wei-Wei Fu, Ling Fang, Shi-Li You, Hui-Juan Zhang, Yu Wang

Journal of Electrochemistry

With the rapid development of China’s economy, the demand for energy is increasing, and environmental problems are becoming more and more serious. The development and utilization of highly-clean new energy fuel can effectively alleviate the energy crisis and environmental pollution. Nowadays, exploring high-efficiency, environment-friendly and low-cost catalysts remains the focus of research in the hydrogen evolution reaction (HER). In this research, firstly, we proposed a three-dimensional porous vanadium nitride (VN) with octahedral structure, which was prepared by a calcination treatment method. The VN catalyst showed a good electrocatalytic activity toward HER, involving a small overpotential of 94.0 mV at -10 …

Influences Of Morphology And Nitrogen Doping On The Electrocatalytic Characteristics For Oxygen Reduction Reaction Of Nio/Rgo, Dong Liang, Heng-Yi Fang, Shuo Yao, Jie-Mei Yu, Zhao-Liang Zhang, Zhan-Kun Jiang, Xue-Ping Gao, Tai-Zhong Huang

Journal of Electrochemistry

In this research, the reduced graphene oxide (rGO) supported sheet-like NiO (NiO/rGO) and spherical-like NiO (NiO/N-rGO) catalysts for oxygen reduction reaction (ORR) were prepared. The structures, morphologies and chemical states of the two catalysts were characterized by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical catalytic performance of the two catalysts for ORR were investigated by cyclic voltammetry (CV), Tafel, linear sweeping voltammetry (LSV), rotating disc electrode (RDE) and rotating ring disc electrode (RRDE) tests. Electrochemical results showed that the current density and onset potential (about 0.89 V) …

Preparation Of Nanostructural Mno-Porous Graphene Hybrid Material By Thermally-Driven Etching Of Mno For Lithium-Air Batteries, Juan Yang, Jun-Wei Lang, Peng Zhang, Bao Liu

Journal of Electrochemistry

In this paper, improving the surface morphology of graphene(GNSs) as designed concept. we describe a MnO/porous-graphene(MnO-PGNSs) was synthesized by a simple site-localized Mn²⁺ on GO (Mn-GO) by charge adsorption and then driving by high-temperature calcination, growing MnO nanoparticles and etching GNSs achieved on step. And Then focus on the key factors of influenced the etch hole formation are analyzed, founded the dispersion of Mn-GO; layer number of GO and calcination temperature also affected the formation of holes. In addition, the MnO-PGNSs as lithium-air battery cathode exhibits high reversible capacity compared with GNSs and PGNs and it is able to …

Progress In Solar Photocatalytic Hydrogen Production, Zhi Wu, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

With the rapid development of human society and dramatically consumption of traditional energy, energy shortage and environmental pollution have become an important factor restricting the sustainable development of human society. At present, the development of clean and environmentally friendly renewable energy system has drawn much attention and becomes an important priority stratagem in the world. In many green and sustainable new energy projects, semiconductor-based photocatalytic hydrogen production technology which utilizes the available clean and renewable solar energy to prepare clean hydrogen energy is excepted to solve the crisis of energy shortage and environmental pollution, has become one of the most …

Special Issue: Electrocatalysis And Fuel Cells, Shuangyin Wang

Journal of Electrochemistry

/

A Facile Route To Synthesize Pt-Wo3 Nanosheets With Enhanced Electrochemical Performance For Her, Peng-Jie Jiang, Yi Lv, Chang-Miao Chen, Hong-Cheng He, Yong Cai, Ming Zhang

Journal of Electrochemistry

Platinum-tungsten trioxide (Pt-WO₃) nanosheets were synthesized on nickel foams (NFs) directly. As great conductive networks, NFs substrates could greatly improve the electrode performance of WO₃. The modified platinum nanoparticles not only enhanced the electron transformation of catalysts, but also increased the active sites for hydrogen evolution reaction (HER). Pt-WO₃/NF revealed a better catalytic activity than WO₃/NFs with a smaller Tafel slope (80 mV·dec^-1) and a lower overpotential of 72 mV at the current density of 10 mA·cm^-2. In addition, Pt-WO₃/NF showed great durability and stability during …

Nickel Selenide Derived From [Ni(En)3](Seo3) Complex For Efficient Electrocatalytic Overall Water Splitting, Dan-Dan Chen, Xue-Qing Gao, Hong-Fei Liu, Wei Zhang, Rui Cao

Journal of Electrochemistry

Electrocatalytic water splitting is considered as a promising technology for renewable energy. The development of efficient, stable, cost-effective, and bifunctional catalysts for both water reduction and oxidation has continued to face significant challenges. Herein, we report a robust and highly active nickel selenide (NiSe) spheres grown on carbon cloth (CC) by electrodeposition from a nickel selenite complex which is a single source containing both Ni and Se. A combination of two chemicals containing, separately, Ni and Se is used in traditional preparations of metal selenides, causing possible problems in the uniformity of the products. The as-prepared NiSe-EA/CC electrode exhibited electrocatalytic …

Pd Nanoparticles Supported On The Etched Ni Foams As High-Performance Electrocatalysts For Direct Ethanol Fuel Cells, Chi Zhang, Cheng-Fei Li, Gao-Ren Li

Journal of Electrochemistry

The development of non-Pt anode electrocatalysts with high activity and long-term durability at low cost for fuel cells still remains enormous challenge. Here we report the Pd nanoparticles supported on Ni foams etched by the mixed acids (HNO₃+H₂SO₄+H₃PO₄+CH₃COOH) (Pd/ME-NF) that are designed and fabricated as high-performance electrocatalysts for ethanol oxidation in alkaline media. Because of the advantages of large open space, fast electrolyte penetration/diffusion and rapid electron transfer process, the Pd/ME-NF catalysts exhibited significantly improved electrocatalytic activity and durability compared with the commercial Pd/C catalysts.

Systematic Comparison Of Two Axial Flux Pm Machine Topologies: Yokeless And Segmented Armature Versus Single Sided, Narges Taran, Greg Heins, Vandana Rallabandi, Dean Patterson, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper systematically compares two axial flux permanent magnet (AFPM) machines designed for a university student racing car application: a double-rotor single-stator yokeless and segmented armature (YASA) structure, and a single- stator single-rotor configuration. Both machines are optimized for minimum loss and active weight using 3D finite element analysis and the highest performing candidate designs are compared in more detail. The studies indicate that the benefits offered by the YASA configuration over the single-stator single-rotor machine are achieved only for specific designs that are heavier. For the design space with lower mass, albeit with increased losses, the Pareto front designs …

Barriers And Opportunities To Electric Vehicle Development In Nepal, Allyson Krupa

Independent Study Project (ISP) Collection

As the global carbon dioxide level reaches its highest point in human history (407.4 parts per million), energy systems must transition from fossil fuel to renewable-powered sources. Since the transportation sector contributes nearly one-third of global greenhouse gas (GHG) emissions, electric mobility offers a significant opportunity to reduce GHG emissions. Globally, there has been a rise in demand for electric vehicles. In Nepal, a clean energy transition within the context of rising urbanization and air pollution is imperative for quality of life, socio-economic development, and broadly climate change mitigation/adaptation. Furthermore, Nepal’s vast hydropower potential may increase energy independence and provide …

Designing An Accessible Wave Energy Conversion Device For Powering Ocean Sensors, Sophie Coppieters ‘T Wallant

Independent Study Project (ISP) Collection

Currently, less than 5% of our oceans are comprehensively monitored and much more ocean data is needed to facilitate understanding of ocean physics, carbon cycling, and ocean ecosystems. Today, most autonomous ocean sensors are powered by primary battery, which have both limited capacity and lifetime. The goal of this research is to design a small, accessible renewable wave energy device to power autonomous free-floating ocean sensors. By designing a cheap, accessible, and simple wave energy converter, this work hopes to make ocean sensor deployment easier and cheaper for researchers, increase the lifetime of autonomous ocean sensors, and reduce the reliance …

2019 Fall Engr333 Project Assignment, Matthew K. Heun

ENGR 333

The Fall 2019 ENGR333 project focused on the energy rebound effect.

I asked the students “How much energy does energy efficiency save?”

This project resulted in a working paper and two journal articles submitted to The Energy Journal. The journal articles remain under review as of October 2023.

Customer

The customer for this project was Dr. Paul E. Brockway, University of Leeds, UK.

Axial-Field Vernier-Type Flux Modulation Machines For Low-Speed Direct-Drive Applications, Vandana Rallabandi, Peng Han, Murat G. Kesgin, Narges Taran, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper proposes different configurations of axial-field machines featuring a very large ratio of the number of rotor poles to stator teeth and coils suitable for low-speed direct-drive traction applications. The machines have a single rotor with spoke-type permanent magnets and the stator teeth include auxiliary slots, the function of which is to enhance the high-polarity component of the stator magnetomotive force interacting with the rotor to produce a net torque. The machines can be constructed with three or two phases, in which case they inherently exhibit high tolerance to faults due to the combined effect of a lack of …

On The Control Of A Solid State Transformer For Multi-Mw Utility-Scale Pv-Battery Systems, Yibin Zhang, Oluwaseun M. Akeyo, Jiangbiao He, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The utility-scale photovoltaic (PV)-battery systems typically include multiple power converters connected to the grid via traditional line frequency transformers (LFT), which may be considered bulky, and inefficient when compared with the emerging solid state transformers (SST). This paper proposes a SST with power and voltage controls for utility-scale PV-battery systems. The PV system was modeled based on available data from a universal solar facility located in Kentucky, USA. Furthermore, this paper provides detailed controller designs for the proposed utility-scale PV-battery system based on a SST which includes: the PV-side dual-active bridge (DAB) converter tracks the maximum power point, the PV …

A Hybrid Analytical And Fe-Based Method For Calculating Ac Eddy Current Winding Losses Taking 3d Effects Into Account, Narges Taran, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper proposes a new hybrid analytical and numerical FE-based method for calculating ac eddy current losses in wire windings and demonstrates its applicability for axial flux electric machines. The method takes into account 3D field effects in order to achieve accurate results and yet greatly reduce computational efforts. It is also shown that hybrid methods based on 2D FE models, which require semi-empirical correction factors, may over-estimate the eddy current losses. The new 3D FE-based method is advantageous as it employs minimum simplifications and considers the end turns in the eddy current path, the magnetic flux density variation along …

Measurement And Estimation Of The Equivalent Circuit Parameters For Multi-Mw Battery Systems, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper proposes and validates through simulations and measurements, a procedure for the determining the equivalent circuit parameters of large utility-scale batteries. It is considered that a large battery includes multiple cells connected in series and parallel, and therefore, its equivalent circuit can be represented as a series-parallel network of state of charge (SOC) dependent resistors and capacitors. Tests for determining these equivalent circuit parameters are proposed. These tests involve subjecting the battery energy storage system (BESS) to multiple charge and discharge cycles, while monitoring the terminal voltage and current response. A method for post-processing and analyzing the measurements in …

On The Optimal Energy Controls For Large Scale Residential Communities Including Smart Homes, Huangjie Gong, Vandana Rallabandi, Michael L. Mcintyre, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Residences with smart home energy management (HEM) systems and solar generation are modifying domestic load profiles. Moreover, the growing penetration of solar photovoltaic (PV) energy brings the total net power demand further down as houses become local generators. High PV penetration introduces technical challenges for the power system including the "duck curve". This paper proposes a co-simulation framework for high PV penetration smart energy communities which allows the simultaneous simulation of home energy consumption along with control algorithms for each house, as well as system power flow. Models are developed and presented for one of the largest rural field demonstrators …

Control Of A Three-Phase Grid-Connected Inverter Under Non-Ideal Grid Conditions With Online Parameter Update, Vikram Roy Chowdhury, Jonathan W. Kimball

Electrical and Computer Engineering Faculty Research & Creative Works

Three-phase grid-connected inverter modeling depends on the equivalent resistance and inductance between the inverter and the grid. However, these parameters are not fixed during the operation of the inverter and vary with the operating conditions. In this paper, a new globally stable adaptive controller is proposed to estimate these values online and update the controller during its operation. A model reference adaptive system (MRAS) based on two fictitious quantities with no physical significance is utilized, namely M = v · i∗ and N = v∗ x i, where v and i are the steady-state values of voltage and current in …

Preface To Special Issue Of Electrochemical Reduction Of Carbon Dioxide, Qing Li, Min Liu

Journal of Electrochemistry

No abstract provided.

Recent Progress In Copper-Based Catalysts For Electrochemical Co2 Reduction, Wen Lei, Wei-Ping Xiao, De-Li Wang

Journal of Electrochemistry

As the situation of energy crisis and environmental pollution become more and more serious, the electrochemical reduction of carbon dioxide (CO₂) has attracted lots of attention because of its multiple meanings such as environment, resources and economic benefits. In this paper, the state of the art electrochemical reduction of CO₂ in aqueous solution is reviewed, and the latest research progress in Cu-based catalysts with different structures and morphologies is summarized. In the end, the application prospects, opportunities and challenges of Cu-based materials are briefly presented to provide an outlook for future research directions.

Regulation Of Copper Surface Via Redox Reactions For Enhancing Carbon Dioxide Electroreduction, Bao-Hua Hang, Jin-Tao Zhang

Journal of Electrochemistry

A large-scale application of fossil fuels has led to excessive emission of carbon dioxide (CO₂), resulting in serious environmental issues. A promising path to reducing CO₂ emissions is recycling CO₂ into valuable chemicals and fuels through an electrochemical process. Herein, the redox reactions between copper (Cu) and ferric chloride (FeCl₃) have been utilized to regulate the Cu surface composition and structure, aimed to improve the electrocatalytic activity toward CO₂ reduction. Typically, a series of samples (named Cu-1h, Cu-2h, Cu-3h and Cu-4h) were prepared via the redox reactions for various time from 1 to …

Single-Layer Oxygen Deficiency Δ-Mno2 For Electrochemical Co2 Reduction, Yue-Feng Zhang, Jian-Jun Liu, Zeng-Xi Wei, Xin-Xin Tian, Jian-Min Ma

Journal of Electrochemistry

Manganese dioxide (MnO₂) has been widely used in catalysis. In addition, since the defect engineering can change the electronic properties of the catalyst, here we have systematically studied electrocatalytic carbon dioxide reduction reaction (CO₂RR) on δ-MnO₂ with and without oxygen deficiency, denoted as Ov-MnO₂ and MnO₂, respectively. We calculate the electronic properties and the intermediate of free energy for MnO₂ and Ov-MnO₂ with the help of spin-polarized density functional theory. By analyzing this result, we can find that the introduction of defects change the δ-MnO₂ from semiconducting properties to …

Statuses, Challenges And Strategies In The Development Of Low-Temperature Carbon Dioxide Electroreduction Technology, Xu-Rui Zhang, Xiao-Lin Shao, Jin Yi, Yu-Yu Liu, Jiu-Jun Zhang

Journal of Electrochemistry

Low-temperature carbon dioxide (CO₂) electrochemical reduction technology is a hotspot for research and development in recent years as a way to reduce the negative impact of CO₂ on the environment and to generate energy storage through converting electricity to low-carbon fuels. Although basic research on catalyst activity, product selectivity, and reaction mechanism has been widely reported, the design and practicality of catalytic stability and corresponding electrochemical reactor systems have not been given sufficient attention and systematic development.  In this paper, two important factors affecting the development of CO₂ electrochemical reduction technology in low temperature aqueous solution …

Copper-Based Compounds For Electrochemical Reduction Of Carbon Dioxide, Fan Yang, Pei-Lin Deng, You-Jia Han, Pan Jing, Bao-Yu Xia

Journal of Electrochemistry

The electrochemical reduction of carbon dioxide (CO₂) to useful chemicals and fuels has attracted enormous interest since the deteriorating global warming and energy shortage problems resulted from ever-increasing CO₂ emission. Designing efficient catalysts is of capital significance to realize the efficient and selective conversion of CO₂. Among various catalysts explored, copper-based compounds have promising potentials with acceptable efficiency for hydrocarbon production. Herein, recent advances on copper-based materials are summarized for electrochemical CO₂ conversion. We intend to include the dimensional structure, different forms (alloy, oxide) and molecular catalysts in copper-based catalysts. Moreover, the reaction mechanisms …

Recent Advances In Bismuth-Based Co2 Reduction Electrocatalysts, Rui Zhou, Na Han, Yan-Guang Li

Journal of Electrochemistry

Carbon dioxide (CO₂) is an economical, secure and sustainable carbon resource around us. Its effective capture and recycling have been the focus of our entire society. Using the electrochemical method, CO₂ can be reduced to different value-added chemicals or fuels. This approach not only would mitigate CO₂ accumulation in the atmosphere, but also would help alleviate our dependence on fossil fuel. In this article, the basic principle and process of electrochemical CO₂ reduction are first introduced. The recent development in bismuth-based catalysts for electrocatalytic CO₂ reduction is reviewed with an emphasis on their preparation, …

Electrocatalytic Reduction Of Carbon Dioxide To Carbon Monoxide Using Cobalt Nitride, Chen Ma, Peng-Fei Hou, Peng Kang

Journal of Electrochemistry

Electrocatalytic reduction of carbon dioxide (CO₂) is a promising method to alleviate global warming issues, although it still faces many challenges. Herein, we report cobalt nitride for electrocatalytic reduction of CO₂ to carbon monoxide (CO) in an aqueous electrolyte. A comparison of catalysts with different preparation temperatures and atmospheres suggests that nitrogen doping is critical to improve catalytic activity. For the most active catalyst of 700-Co_5.47N/C, the CO current density reached 9.78 mA·cm^-2 at potential of -0.7 V vs. RHE. In addition, the CO/H₂ ratio could be adjusted from 1:3 to 3:2 by …

Effect Of Morphology Of Fe-N Codoped Carbon Nanomaterial On Electrochemical Reduction Reactions, Er-Ling Li, Fa Yang, Ming-Bo Ruan, Ping Song, Wei-Lin Xu

Journal of Electrochemistry

Graphene nanosheets (GS) and carbon nanotubes have been considered as good catalysts candidates for applications in energy conversion and storage. However, hybrids of GS and carbon nanotubes are always formed in transition metal-based nitrogen-doped system, making the system quite complex for exploring the structure-activity relationship. To prepare the catalysts with desired species controllably, we try to adjust the outcomes with the effect of nitrogen on the growth of carbon nanotubes. In this work, a series of Fe-N co-doped carbon hybrid catalysts containing N-doped GS or hybrids of GS/bamboo carbon nanotubes (BCNTs) or BCNTs were obtained with one-step pyrolyzed method. To …

Electrochemical Detection Of 4-Nitrophenol Based On Glassy Carbon Electrode Modified By Tio2Nps/Rgo Composite, Lin-Na Jiu, Yong-Qiang Cheng

Journal of Electrochemistry

4-nitrophenol (4-NP) has become factitious pollution, and presented a serious threat to the nature and human health. It is necessary to develop a convenient and fast detection method. In this work, the glassy carbon electrode modified by titanium dioxide nanoparticles (TiO₂NPs)/reduced graphene oxide (RGO) composite as an electrochemical sensor was studied for the trace detection of 4-NP. The morphology of the composite was characterized by scanning electron microscopy (SEM). The homogeneous mixing of titanium dioxide nanoparticles and reduced graphene oxide increased the specific surface area of the composite, and facilitated the electrochemical reaction of 4-NP. The electrochemical characteristics …

Preparations And Electrocatalytic Properties Of Cu-Bipy-Btc-Derived Carbon-Based Catalyst For Oxygen Reduction Reaction, Li-Hua Zhang, Jun-Feng Chen, Wan-Tang Huang, Yong-You Hu, Jian-Hua Cheng, Yuan-Cai Chen

Journal of Electrochemistry

Efficient and low-cost oxygen reduction reaction (ORR) electrocatalyst plays a key role for fuel cells. In this paper, ORR active metal organic framework (MOF: Cu-bipy-BTC, bipy = 2,2?-bipyridine, BTC = 1,3,5-tricarboxylate) was prepared using hydrothermal method, and then carbon-based material MOF-800 was obtained from pyrolyzing Cu-bipy-BTC at 800 °C. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), nitrogen sorption isotherm and X-ray photolectron spectroscopy (XPS) were used to characterize the morphologies and structures of the catalysts. Linear sweep voltammetry (LSV) and current-time curve (i-t) were adopted to evaluate the electrocatalytic properties of the catalysts. The results …

Understanding Of The Ship Design Energy Efficiency And Its Implications In Practice, Haichao Yuan

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.