Power and Energy Commons^™

Steady State Voltage Stability Enhancement Using Shunt And Series Facts Devices, Jahnavi Lakkireddy

LSU New Orleans Theses and Dissertations

It is specifically important to focus on voltage stability analysis of the power system to avoid worst case scenarios such as voltage collapse. The purpose of this thesis is to identify methods for enhancing the steady-state voltage stability using FACTS devices and determining their impact on real and reactive power losses, improvement of bus voltage magnitude, and transmission line loadability. To achieve this, FACTS devices such as Static VAR Compensator (SVC), Static Synchronous Compensator (STATCOM), and Thyristor Controlled Series Capacitor (TCSC) are used in the test system as three separate test cases. The results obtained assist in drawing conclusions on …

Polymer-Based Thermoelectric Devices, Stuart W. Hilsmier, Edward P. Tomlinson, Bryan Boudouris

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, over 50% of all energy generated in the US is lost as waste heat, and thermoelectric generators offer a promising means to recoup some of this energy, if their efficiency is improved. While organic thermoelectric materials lack the efficiency of their inorganic counterparts, they are composed of highly abundant resources and have low temperature processing conditions. Recently, a new class of redox-active polymers, radical polymers, has exhibited high electrical conductivity in an entirely amorphous medium. In addition, these radical polymers have a simple synthetic scheme and can be highly tunable to provide desired electrical properties. In this study, the …

Medical Applications Of Mrc, Kyle Thackston, Henry Mei, Pedro Irazoqui

The Summer Undergraduate Research Fellowship (SURF) Symposium

Consistent powering is a limiting reagent for many medical implants and sensors. Powering in-vivo devices in animal studies requires either transcutaneous wiring (limiting mobility and increasing the chance of infection) or an implanted battery (limited lifetime and limits size of device). Wireless power transfer (WPT) would be able to overcome these challenges and permit the use of more advanced implantable devices in a research setting. Magnetic resonance coupling (MRC), an advanced form of inductive charging, allows good transfer efficiencies over significant air gaps, but works best a specific location and frequency, limiting mobility in animal studies. Using band-pass filter theory, …

Solar-Combined Thermoelectric Power Generation Simulator, Hemanth Mullangi Chenchu, Kazuaki Yazawa, Je-Hyeong Bahk

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaic (PV) devices are gaining popularity in harnessing solar energy as a form of sustainable energy source to generate electricity. However, these devices including tandem PV cells are limited to utilizing only high energy photons from the solar spectrum. This curtails their efficiency restricting them from being employed in mega Watts scale power generation. This study develops a software tool that allows engineers to tap into the wasted wavelengths of the spectrum by adding a thermoelectric (TE) module and a bottoming steam turbine cycle thus spreading the use of the spectrum. The tool allows investigating how power output and thus …

Radical Polymers As Anodic Charge Extraction Layers In Small Molecule Organic Photovoltaic Devices, Krystopher S. Jochem, Aditya G. Baradwaj, Bryan W. Boudouris

The Summer Undergraduate Research Fellowship (SURF) Symposium

Organic photovoltaic (OPV) devices based on the copper (II) phthalocyanine(CuPc)/ fullerene(C₆₀) system are an innovative photovoltaic technology optimal for situations requiring low-cost, transparent, and flexible devices. Furthermore, the high degree of reproducibility of this system allows for the ready study of new OPV technologies. Here, we have used this system to elucidate systematic structure-property-performance relationships for a new OPV anode modifier. The addition of interfacial modifier materials between the organic CuPc/C₆₀ layers and the metallic anode drastically can improve efficiency. Radical polymers are a class of polymers with aliphatic backbones and pendent stabilized radical groups. Here, we …

A Prototype Microwave Cavity Control Circuit For Use In Next Generation Free Electron Laser, Josh Thompson, Peter Neal Barrina, Jiayi Jiang, Joe Frisch, Steve Smith, Daniel Van Winkle

STAR Program Research Presentations

One of the current programs at SLAC National Accelerator Laboratory is the Linac Coherent Light Source, or LCLS. Using the existing hardware of the last third of their linear accelerator (or “linac”), SLAC has created one of the most energetic X-ray free electron lasers (or “FEL”). Since 2009, LCLS has used this FEL to perform a wide range of experiments across all sciences, most notably ultrafast filming at the molecular scale. As requests for beam-time with this laser increases, SLAC is purposing a linac upgrade to better match this demand. This upgrade, named LCLS-II, will replace existing copper radio frequency …

An Experimental Investigation Towards Improvement Of Thermoelectric Properties Of Strontium Titanate Ceramics, Arash Mehdizadeh Dehkordi

All Dissertations

The direct energy conversion between heat and electricity based on thermoelectric effects is a topic of long-standing interest in condensed matter materials science. Experimental and theoretical investigations in order to understand the mechanisms involved and to improve the materials properties and conversion efficiency have been ongoing for more than half a century. While significant achievements have been accomplished in improving the properties of conventional heavy element based materials (such as Bi$_2$Te$_3$ and PbTe) as well as the discovery of new materials systems for the close-to-room temperature and intermediate temperatures, high-temperature applications of thermoelectrics is still limited to one materials system, …

Characterization And Testing Of A 5.8 Kv Sic Pin Diode For Electric Space Propulsion Applications, Alexandra Toftul

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Inductive Pulsed Plasma Thrusters (IPPTs) are a type of in-space propulsion that has multiple advantages over conventional chemical propulsion for long-duration, deep space missions. Existing IPPT prototypes utilize spark gap switches, however these are subject to corrosion problems that make them unreliable for long-term use. Recent advances in solid state switching technology have opened up a variety of switching options that could provide greater reliability, controllability, and increased energy efficiency. Taking advantage of this, a novel thruster drive circuit topology containing a high-power silicon controlled rectifier (SCR) and series fast recovery diode (FRD) is proposed that is expected to increase …

Unbalanced Current Static Compensator, Manuel Antonio Sanchez Tejada

Graduate Theses and Dissertations

The objective of this thesis is to present and evaluate a solution to the unbalanced current issue that can be found in three-phase electrical power grids. The solution is named unbalanced current static compensator (UCSC) and has the goal of balancing the currents at the source in order to mitigate adverse issues such as of negative- and zero-sequence currents that are generated by three-phase current unbalances.

The solution topology consists of three single-phase H-bridge converters that are controlled through an algorithm working in the d-q frame of reference. The algorithm is divided in three different stages: the phase synchronization and …

Potential And Technological Advancement Of Biofuels, Rajee Olaganathan, Fabian Ko Qui Shen, Lim Jun Shen

Publications

This scientific paper examines the feasibility of biofuels as a solution to the world‟s energy crisis. It studies the development of the four different generations of biofuel that have been discerned over the years, determining the pros and cons of each. The paper further investigates the issues concerning each generation, and determines how their successors have solved and improved on those problems. In order to give the reader an unbiased perspective, the paper studies both general advantages and disadvantages that encompasses social, economic and environmental impacts. Research and development on the first two generations of biofuels have matured, and case …

Development Of A Black-Box Transient Thermal Model For Residential Buildings, Andrew Cross

UNLV Theses, Dissertations, Professional Papers, and Capstones

Heavily populated metropolitan areas located in cooling-dominated climates, as are found in the Desert Southwest, pose a challenge to electrical utilities that service these areas. During the late afternoons of the summer months, residents of these metropolitan areas require larger than normal amounts of power to run their homes' air conditioning systems, at significant expense to the utilities. In the study reported here, interior temperature and power consumption data, accumulated over the course of a year and a half from seven houses within a Las Vegas neighborhood, are used to develop a predictive black-box statistical model for residential thermal transience. …

Idpal – A Partially-Adiabatic Energy-Efficient Logic Family: Theory And Applications To Secure Computing, Mihail T. Cutitaru

Electrical & Computer Engineering Theses & Dissertations

Low-power circuits and issues associated with them have gained a significant amount of attention in recent years due to the boom in portable electronic devices. Historically, low-power operation relied heavily on technology scaling and reduced operating voltage, however this trend has been slowing down recently due to the increased power density on chips. This dissertation introduces a new very-low power partially-adiabatic logic family called Input-Decoupled Partially-Adiabatic Logic (IDPAL) with applications in low-power circuits. Experimental results show that IDPAL reduces energy usage by 79% compared to equivalent CMOS implementations and by 25% when compared to the best adiabatic implementation. Experiments ranging …

Grid-Scale Energy Storage: A Proposed Control Algorithm For Sodium Sulfur Batteries, Daniel Spaizman

Master's Theses

With carbon dioxide levels in our atmosphere reaching record highs and 2020 quickly approaching, California is expected to pave the way for the United States in terms of replacing fossil fuel generation facilities with various renewable energy power plants. It is well documented that the inherent variability and limited duty cycle of renewables has hindered their growth. Energy storage technologies represent the bridge that can help us cross the divide from where we stand to where we must stand in the next 6 years. Utility companies value services such as peak shaving, voltage support, and frequency regulation, all of which …

Horseradish Peroxidase-Attapulgite Clay Nanocomposites: Fabrication And Application To Sensing The Extracellular H2O2 Released From Cells, Ping Wu, Chen-Xin Cai

Journal of Electrochemistry

The nanostructured attapulgite clay was employed as a support matrix for immobilizing horseradish peroxidase (HRP). FTIR and electrochemical methods demonstrated that HRP had been effectively assembled on attapulgite surface with the formation of HRP-attapulgite nanocomposites. The HRP-attapulgite hybrid was deposited on the glassy carbon (GC) electrode forming the HRP-attapulgite/GC electrode. Cyclic voltammetric results showed a pair of well-defined redox peaks, which were ascribed to direct electron transfer (DET) of HRP, with the formal potential E₀′ = -335 mV (vs. SCE) in the phosphate buffer solution (PBS, pH 7.0). The dependence of E₀′ on solution pH indicated …

The Ionic Diffusion Model For The Solid Oxide Cathode And Its Verification By The Electrolysis Of Ta2O5 In Molten Cacl2, Hua-Lin Chen, Zhi-Yong Wang, Xian-Bo Jin, George Z. Chen

Journal of Electrochemistry

The deoxidation speed of a solid oxide cathode in molten CaCl₂ can be estimated by the PRS steady diffusion model of O^2-, which correlates the deoxidation speed with the precursor porosity, P, the metal-to-oxide molar volume ratio, R, and the cathode volume shrinkage S. The PRS model indicates that the porosity of the oxide cathode has important influence on the deoxidation speed, and provides a very simple equation for the prediction of the optimal cathode porosity. For the electrolysis of Ta₂O₅, the porosity of the cathode is better to be within 50%. …

23Na Mas Nmr Spectroscopic Study Of Na2Mnpo4F As Cathode Material For Sodium-Ion Battery, Xu Hou, Gui-Ming Zhong, Xiao-Chen Lin, Zi-Geng Liu, Xiao-Biao Wu, Yong Yang

Journal of Electrochemistry

The Na₂MnPO₄F is one of the promising cathode materials for the sodium ion batteries. In the paper, we employed the ex situ X-ray diffraction and solid state NMR techniques to study the charge and discharge processes of this material, including the crystal structure and sodium sites changes. The ex situ x-ray diffraction patterns showed that two new diffraction peaks could be observed at 31^o and 36^o indicating an intermediate phase formed with the extraction of Na⁺. From the ²³Na MAS NMR spectrum of the material, three peaks were seen at -209 …

Effects Of Oxygen Coverage And Hydrated Proton Model On The Dft Calculation Of Oxygen Reduction Pathways On The Pt(111) Surface, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

DFT calculation is used to study various possible steps in the oxygen reduction reaction (ORR), including the adsorption and dissociation process of O₂ and the serial protonation process of dissociated products to form H₂O on the Pt(111) surface. By using slabs of different sizes, and different numbers of pre-adsorbed oxygen atoms, the coverage effects on the pathways are investigated. The calculated results using different hydrated proton models are also compared. It is shown that the initial step of the ORR is the formation of a protonated end-on chemisorbed state of OOH*, which can transform to an unprotonated …

Simulation Of A Smart Home Energy Management System With Dynamic Price Response, Jason Y. Chan, Qinran Hu

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

With the continuing development of the smart grid combined with the fluctuating nature of the electricity market, the development of demand-side management with controllable loads have been greatly driven. With the amount of household loads in the residential sector, managing their energy usage has received lots of interest. This paper presents a simulation of a previously proposed hardware design of a smart home energy management system (SHEMS), focusing on the data collection and processing functions of the proposed design while implementing them onto standard household loads like an electric water heater and an electric vehicle charging station. It was found …

High Energy Battery Team Capstone Project Report, Evan Bowen, Brandon Cash, John Edinger, Matt Muller

James Madison Undergraduate Research Journal (JMURJ)

James Madison University’s High Energy Battery Team was commissioned in Fall 2011 to conceptualize, design, prototype, test, and construct a high voltage, high amperage battery pack capable of powering an all-electric motorcycle at a speed of 70 miles per hour for a minimum of 150 miles. Key design goals were to minimize volume and weight and to maximize power output, reliability, and serviceability. This project report details the Team’s work to develop a battery “sub-pack” using 18650-type lithium ion cells which could be used (in a full-size battery pack) to power a future version of the motorcycle. The ultimate project …

An Assessment Model For Energy Efficiency Program Planning In Electric Utilities: Case Of The Pacific Of Northwest U.S.A., Ibrahim Iskin

Dissertations and Theses

Energy efficiency stands out with its potential to address a number of challenges that today's electric utilities face, including increasing and changing electricity demand, shrinking operating capacity, and decreasing system reliability and flexibility. Being the least cost and least risky alternative, the share of energy efficiency programs in utilities' energy portfolios has been on the rise since the 1980s, and their increasing importance is expected to continue in the future. Despite holding great promise, the ability to determine and invest in only the most promising program alternatives plays a key role in the successful use of energy efficiency as a …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

Battery Management System, Michael Desando, Kyle Woody

Electrical Engineering

Problem Statement:

There have been recent reports of multi-million dollar companies having to recall entire projects due to their BMS’s malfunctioning or operating incorrectly. The purpose of this project is to analyze the future of batteries, the Lithium-Ion cell, and to exercise a BMS to better understand its capabilities and possible cases for errors. Lithium ion batteries are intolerant of overcharge and overdischarge. Abuse of this kind can result in high temperatures, venting of gases, fire, or explosion. Therefore battery management systems have been devised to prevent such abuse. Recent events such as fires on the Boeing Dreamliner and the …

Wind And Ventilation Turbine (Wvt) Generator, Anthony Lloyd, Jacob Michener

Electrical Engineering

This project aims to create a more compact and accessible renewable energy source using the Wind and Ventilation Turbine (WVT) Generator. The wind turbine provides ventilation while generating “clean” electricity using solar and kinetic energy. The electrical generation causes no functional losses to the ventilation as rising heat and passing wind turn the turbine, ventilating the house. Placing a generator beneath the spinning turbine allows for the transformation of mechanical motion into electrical energy. The system charges a battery, supplying recharging power into small standard electronics (i.e. cell phones, tablets, etc.) through a USB output.

Buck-Boost Dc-Dc Converter With Input Protection System For The Energy Harvesting From Exercise Machines Project, Byungjae David Yoo, Sheldon Tyler Kong Ming Chu

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) project comprises of multiple subprojects seeking to effectively create a sustainable energy source through harvesting electrical energy generated from physical exercise machines. This project designs and implements a Buck-Boost DC-DC converter using a LT3791-1 4-Switch Buck-Boost Controller, replacing the previous SEPIC design. The DC-DC converter must operate within limits set by the maximum input range of the LT3791-1 controller. An input protection system prevents inputs higher than rated values, which may adversely damage the Buck-Boost DC-DC converter. These inputs include overvoltage transients, average voltage, and current output by the Precor EFX 561i …

Piezoelectric Powered Led Street Reflector, Collin Shane Douglass

Electrical Engineering

In many areas of Washington, it rains for a majority of the year. During rainy weather it becomes difficult to see street lanes and dividers, causing hazardous road conditions. The Piezoelectric Powered LED Street Reflector solves this problem. The PPL Street Reflector modifies a street reflector with LED lights. These lights help drivers clearly see where dividers and street lines are in non-ideal weather conditions, such as rain, fog, and snow. The PPL Street Reflector capabilities include harvesting energy through the Piezoelectric Effect, creating a self-sustaining device with minimal maintenance.

Portable Nano Hydro Generator For The Dc House Project, Caleb David Fink, Victor Olusoji Ojewole, Christopher Mapua Tan

Electrical Engineering

This Senior Project entails the design and testing processes of the Portable Nano Hydro Generator for the continuing DC House Project. No natural resources should go unused, especially in developing countries where they are found in abundance. Small streams in particular have potential to further Professor Taufik's DC House Project that will provide electricity to 1.6 billion people in the world without access to electricity upon completion. The goal of this project is to create a small portable generator that utilizes the discharge from small streams and convert it into useable electricity that could charge a car battery as an …

All Purpose Mobile Gps, James C. Smith, Matt Weege, Kevin Peters

Electrical Engineering

The aim of the All Purpose Mobile GPS (The System) is to create a GPS tracking device that can accurately record location and calculate velocity, distance traveled and elevation change even when the satellite signal is lost. This data can later overlay on existing internet-based maps illustrating a trip to oneself or others. The portable tracker consumes very little power achieving several days’ worth of power in a single charge. A solar cell provides a quick battery boost in a pinch. SD Card storage increases compatibility with computers and other forms of data transfer. Data processing, such as viewing the …

Design Improvement For The Smart Dc Wall Plug, Cory Yee, Haoyan Huang

Electrical Engineering

The DC smart wall plug is a subsystem within the Cal Poly DC House Project. The previous version faces challenges supplying DC voltage to meet household appliances’ nominal values. Specifically, it can only output the minimum required voltage for DC appliances to operate, resulting in unwanted power loss. In addition, the maximum output voltage is rated at 15V, which is insufficient to power most DC appliances. This design improvement project incorporates NFC technology as a solution to overcome the power loss and a new buck converter configuration to increase the output voltage range. Additionally, the new design introduces short-circuit and …

Energy Harvesting From Exercise Machines - Dc-Dc Buck Boost Converter (Lt3791), Matthew B. Wong

Electrical Engineering

Cal Poly’s ongoing Energy Harvesting From Exercise Machines (EHFEM) project proposes sustainability and energy saving costs through modifying exercise machines generating DC power, providing a renewable energy resource through physical exercise. The EHFEM project contains multiple sub-projects involving modifying several different exercise machines. Each machine generates DC power and an inverter converts this power to AC. This AC power returns to the grid. This project addresses an issue involving a previously installed DC-DC converter not returning power properly. When generating DC power, the grid demands a specific AC voltage, but the generated power through the previous DC-DC converter and power …

Cnc Torch, Steven Chiu

Computer Engineering

This CNC Torch cuts steel plate. It can cut up to a maximum area of 3x3 feet. The user builds a cut list on the touchscreen from a selection of predefined shapes and enters the parameters need for each shape. When the user is ready, the cut list is sent to an Arduino that will move each motors accordingly to the shapes desired.