Power and Energy Commons^™

Smart Home System Prototype, Comparing And Evaluating Current Technologies, Marco Antonio López, David Guzman, Virgilio Gonzalez

COURI Symposium Abstracts, Summer 2012

Imagine a world where blackouts can be prevented, reduced, or even removed completely. This one of the many benefits a Smart Grid would bring. The integration of the Smart Grid would bring all these benefits by being able to transfer information through all stages of electricity; generation, distribution, and consumption. This research is concentrated on the Smart Home –the consumption stage of electricity. Specifically, on technologies available that can be used towards the designing of the Smart Home. Before being able to design a Smart Home, it is necessary to decide which technologies are best for the job; be it …

Low Power Sigma Delta Converter, Noel P. Martinez, Praveen K. Palakurthi, Eric Macdonald

COURI Symposium Abstracts, Summer 2012

Sub threshold technology allows for circuits to run at their best efficiency with the lowest amount of energy possible. The aim of this research was to combine this technology along with radiation hardness, or the ability for circuits to resist radiation without getting corrupted data. A chip that can convert digital data into analog data (DAC) was created and programmed using verilog, a Hardware Description Language (HDL). With verilog, we created digital data that would eventually be fed into the chip using a field-programmable gate array (FPGA) board. We tested our digital data using a test bench on the computer …

Preparation And Electrochemical Performance Of Tio2/Gns Nanocomposite As Anode Materials For Lithium-Ion Batteries, Lin-Lin Qin, Huan Zhang, Xiao-Jing Liu, Jian-Hui Xu, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The honeycomb-like porous TiO₂/graphenes (TiO₂/GNs) nanocomposite was prepared by a reflux method. SEM and TEM results showed that nanosized anatase TiO₂ (about 5~10 nm) were dispersed uniformly on the surface of the GNs. The TiO₂/GNs composite showed excellent rate and cycling performance: A stable charge capacity of 169.5 mAh·g^-1 was obtained at 30C, and can restore to 241.7 mAh·g^-1 while current went back to 1C. The stable charge capacity of TiO₂/GNs nanocomposite electrode up to 201.9 mAh·g^-1 was achieved at 10C in the first cycle, and could be …

An Overview Of Electrode Materials In Microbial Fuel Cells, Su-Qin Ci, Na Wu, Zhen-Hai Wen, Jing-Hong Li

Journal of Electrochemistry

Microbial fuel cells (MFCs) are devices that can directly convert organic chemical energy into electrical energy with microbial as catalysts. MFCs are a promising bio-electrochemical system with the potential to degrade organic sewage and produce electricity. This article supplies a critical and comprehensive review for the electrode materials concerning about anode and cathode in MFCs, including the fabrications, functional modifications and surface constructions of electrode materials, as well as their applications in MFCs. Additionally, the existing problems of electrode materials in current MFCs have been demonstrated in order to provide the guideline for exploring the next-generation electrode materials for MFCs.

Novel Molten-Salt Electrolysis Processes Towards Low-Carbon Metallurgy, Wei Xiao, Hua Zhu, Hua-Yi Yin, De-Hua Wang

Journal of Electrochemistry

This review focuses on recent developments in molten-salt electrolytic metallurgical processes with respect to 1) high-efficiency metallurgical technologies via electrolytic reduction of solid oxides in molten chlorides and 2) zero-carbon-footprint electrochemical splitting metallurgical technologies. Initiating with an introduction on dynamic solid/solid/liquid three-phrase interlines electrochemistry for electrochemical reduction of solid cathode, the former aspect is discussed in terms of facilitating mass transfer throughout solid cathode, one-step production of functional alloy powders with the assistance of under-potential electroreduction of active metals and near-net-shape production of metal/alloy components. Whilst the latter is summarized by introducing some zero-carbon molten-salt electrolytic technologies including electro-splitting of …

Comments On Internal Alternating Current Resistance Test Standard And Methods Of Lithium-Ion Batteries, Ya-Li Zhang, Sen Xin, Yu-Guo Guo, Li-Jun Wan

Journal of Electrochemistry

The sustainable development of energy and environment is one of the most influential issues of this century. Batteries, especially secondary batteries are important for powering out daily life. However, in many practical applications, such as in electric vehicles and hybrid electric vehicles, batteries should be used in packs and the performance consistency of each battery in the pack should be taken into consideration. As one of the performance parameters being used to characterize the battery consistency, internal resistance is of great importance to the industrial fabrication and the use of batteries. Currently, internal resistance tests of secondary batteries, such as …

Methodological Significance Of "Property-Activity Relationship" For Catalyst Studies, Jun-Tao Lu, Li Xiao, De-Li Wang, Yu-Bao Sun, Yan-Ge Suo, Lin Zhuang

Journal of Electrochemistry

Instead of attempting the structure-activity relationship (SAR), which is commonly regarded as the core problem for catalyst studies, this paper highlights the methodological significance of “property-activity relationship (PAR)”. The “property” here refers to an index （such as the adsorption energy of an intermediate） or a group of indexes reflecting the behavior of a catalyst which interacts with reactants or intermediates, and is a bridge between structure and activity. Because property is related to activity more directly than structure to activity, PAR should be simpler, less difficult and, therefore, more feasible to be accessed than SAR. Once the key property is …

Simple Analysis And Possible Solutions Of The Unusual Interfacial Reactions In Li-S Batteries, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang

Journal of Electrochemistry

Rechargeable Li-S batteries are a promising power source with realizable energy densities several times higher than current Li-ion batteries. However, the capacity utilization and cycling stability of the existing Li-S technologies are still insufficient for battery applications. The causes for the electrochemical instability of this redox system arise probably from the changes in the surface structures and electrochemical microenvironments of the Li anode and sulfur cathode during charge-discharge reactions, which includes the frustrated electron transfer in the sulfur-carbon interface, the dissoluble diffusion of the polysulfide intermediates, and the shuttle reaction inbetween the sulfur and Li electrodes. To deal with these …

Application Of First Principles Calculations In Anode Materials For Lithium Ion Batteries, Tian-Ran Zhang, Dai-Xin Li, Si-Qi Yang, Zhan-Liang Tao, Jun Chen

Journal of Electrochemistry

First principles calculations play an important role in the study and development of new materials for lithium batteries. In this paper, we review the application of first principles calculations in the design of anode materials, including the modeling of the interaction of lithium in the anode materials, capacity, voltage, electrochemical reaction process, diffusion, rate capability, the relationship between the structure and properties, and the experimental phenomena interpreting. Based on the discussions, we emphasize on the importance of first principles calculations and demonstrate their requirement for further development.

The Electrocatalytic Performance Of Pd Catalysts Supported On Pvp Modified Mwcnts For Formic Acid Oxidation, Jing Zhang, Xiao Zhao, Chang-Peng Liu, Wei Xing

Journal of Electrochemistry

In this paper the MWCNTs were modified by Poly (N-vinyl-2-pyrrolidone) (PVP) to support Pd nanoparticles, which were used as the catalyst for formic acid electrooxidation. And the performance of Pd/PVP-MWCNTs catalysts was studied by electrochemical measurements. The observations from Fourier transforms infrared spectrometer (FTIR) and transmission electron microscopy (TEM) illustrated that the Pd nanoparticles with a small size and narrow size distribution were highly dispersed on PVP-MWCNT support. Therefore, the Pd/PVP-MWCNTs catalysts showed excellent catalytic activity for formic acid electrooxidation.

Synthesis Of Spherical Ni3S4 By Solvothermal Method As Supercapacitor Electrodes, Qing-Na Huan, Li-Fang Jiao, Qing-Hong Wang, Hong-Mei Du, Jia-Qin Yang, Wen-Xiu Peng, Yi-Jing Wang, Hua-Tang Yuan

Journal of Electrochemistry

The Ni₃S₄ microspheres have been synthesized via a facile solvothermal method. The crystal structure and surface morphology are characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Microspherical Ni₃S₄ exhibits good electrochemical capacitance validated by electrochemical measurements. The specific capacities of 1120.6 F∙g^-1 at 0.5 A∙g^-1 and 433.4 F∙g^-1 at 4 A∙g^-1 with the capacitance retention of 89.37 % and 84.88 % were obtained after 1000 cycles, respectively. The electrochemical reaction is expected due to the transformation of Ni(OH)₂ and NiOOH based on the XRD, XPS and CV …

An Application Of Con-Resistant Trust To Improve The Reliability Of Special Protection Systems Within The Smart Grid, Crystal M. Shipman

Theses and Dissertations

This thesis explores an application of a con-resistant trust mechanism to improve the performance of communications-based special protection systems to further enhance their effectiveness and resiliency. New initiatives in the energy sector are paving the way for the emergent communications-based smart grid technology. Smart grids incorporate modern technologies in an effort to be more reliable and efficient. However, with the benefits of this new technology comes added risk. This research utilizes a con-resistant trust mechanism as a method to quickly identify malicious or malfunctioning protection system nodes in order to mitigate the resulting instabilities in the smart grid. The feasibility …

Agenda: A Low-Carbon Energy Blueprint For The American West, University Of Colorado Boulder. Natural Resources Law Center, University Of Colorado Boulder. Renewable And Sustainable Energy Institute, Western Resource Advocates, Rocky Mountain Research Station (Fort Collins, Colo.)

A Low-Carbon Energy Blueprint for the American West (Martz Summer Conference, June 6-8)

The future of the planet may depend upon our ability to increase energy supplies even as we reduce carbon emissions. This conference will address how a low-carbon energy program might evolve with a particular focus on the American West. It will focus on the future of energy in the West--on a “managed transition” to a different energy mix, on the need to nest this effort in a framework that acknowledges interconnections, and on identifying the most salient opportunities to consider the legal, political, financial, and technical challenges.

Design And Simulation Of Interconnected H-Bridge Inverter, Samuel Muehleck

Computer Engineering

In this project, the research, design and simulation of an interconnected H-bridge single-phase inverter was explored. The inverter design was divided into three separate sections. First, a VHDL programmed CPLD was used to generate control signals for the transistors of the inverter circuit. Second, power electronics was used to create an inverter circuit to change a DC input to a 60 Hz AC output. Lastly, additional circuits were used to link the generated control signals to the MOSFET transistors of the inverter circuit. The operation of the three components was then validated with computer simulations. Results of computer simulation demonstrate …

Multiple Input Single Output (Miso) Dc-Dc Converter For The Dc House Project, Owen Jong

Electrical Engineering

This senior project report explains the design of a Multiple Input Single Output (MISO) DC-DC converter for the DC House Project. MISO DC-DC converter interfaces multiple different power sources such as Wind and Solar Energy sources as the inputs to a DC house. The report demonstrates the functionality and the performance of the proposed converter using Flyback topology by showing the theoretical simulation and hardware testing results. Results show the ability of the proposed MISO converter to supply up to 150 Watts from three sources while maintaining maximum efficiency of 92% at full load.

Human Powered Generation - Seesaw: A Dc House Project, William Varsh, Jeffrey Healy

Electrical Engineering

This project is a proof of concept work, where playground equipment is implemented for power generation. In using a seesaw design, this project was able to show how a simple mechanical motion could be transformed in electrical power. A seesaw power generator was designed and constructed to demonstrate its feasibility. Results show that with some modification and improvement to the current design, the seesaw me indeed provide a viable method to produce electricity.

Cell Phone Charger For The Dc House Project, Andrew Hefner, Antonio Magdaleno

Electrical Engineering

The goal of this project is to create a multiple output cell phone charger for the DC House project. The cell phone charger is essentially a DC-DC converter. The converter takes an input of 48 volts from the outlet in the DC House and decreases the voltage level to 5 volts; the input voltage level of all cellular devices. By designing an isolated flyback converter with initial specification in LTSpice simulation software, a converter was created. By monitoring the input and output voltage and current using the multi-meters and electronic load, we determined the charger to be 71% efficient when …

Dc House Model Design And Construction, Mark Cabaj

Electrical Engineering

Approximately 1.6 billion people currently live without electricity. The only sensible solution to their energy problems is the use of renewable energy in an off-grid, autonomous home which is powered directly by direct current, rather than alternating current coming from a power line, which probably cannot be found nearby. The purpose of this project is to construct a prototype of the DC House. More specifically, this project focuses on the development and construction of the power distribution system of the DC House. The system will be put in place starting from the source side model down to the load side …

Solar Powered Led Lantern For Developing Countries, Lacy Billingsly Iii

Electrical Engineering

In recent years, both LED and solar technology have become the focus of sustainable energy. LED lighting uses significantly less power than its fluorescent competitor. Solar cells enable clean, natural, and portable power. As these two entities become more efficient at exponential rates, the hope for the wide use of off-grid lighting in less developed countries seemingly increases at the same rate. Currently, there has been a development of industry for portable solar powered lighting systems. Before designing a product, a study was conducted of current products on the market that aim to light dark homes. This study and design …

12 Volt Wall Outlet For The Dc House Project, Dylan Van Lant, Chenxi Zhang

Electrical Engineering

The purpose of this project is to build a DC-DC converter for the wall outlet of the DC House. This report focuses on the development of the DC -DC converter, and explains the design process as well as summarize the final results. The proposed system using the Buck or Step Down topology takes input voltage of 48V and output 12V at 100W. Results show the ability of the converter to fulfill such tasks while maintaining efficiency about 90% at all load.

Compulsator Design For Electromagnetic Railgun System, Bryan Bennett

Electrical Engineering

This project designed, fabricated, and partially tested a compensated pulsed alternator (compulsator) to power an electromagnetic rail gun (EMRG) in a multidisciplinary team. The EMRG team includes two master’s AERO students, two senior EE students, and three senior ME students. Design of the compulsator began with research through conference and research papers. This design was changed throughout the project as system analysis and component testing exposed unforeseen system limitations. While original specifications were not met, all fabricated components but one, the stator, were completed using Cal Poly’s facilities and the project’s limited available budget. Experimental verification of calculations and system …

Hearst Hydroelectric Generation Facility, Anthony Schifano, Richard Wright, Nick Buchanan, Corey Nakai, Joshua Rutheiser

Electrical Engineering

This project proposes a power plant design that provides a supplemental source of electricity for appliances, machinery, and lighting at Hearst Castle and Ranch. The design concept includes a turbine-generator combination to convert kinetic and gravitational potential energy from the existing water distribution system to electrical energy: also known as a hydroelectric plant. The electrical distribution system from the plant to the local grid takes advantage of power flow techniques utilized in current research and industry.

Retrofitting A Car Alternator For Low-Speed Power Generation, Yuri Carrillo

Electrical Engineering

This report presents the analysis and methods taken to appropriately modify a car alternator to operate as a low speed generator for wind or hydro power generation. A Toyota car alternator taken from a junkyard is characterized via an Open-Circuit test to evaluate its operating specifications. The car alternator is also measured to determine its physical dimensions. The acquired values are used with the generated voltage equation to determine the machine’s unknown rotor values— the product of the rotor winding factor and the number of rotor windings (kfNf). Using the generated voltage equation with the determined machine parameters, the number …

High Efficiency Audio Amplifier, Grant Moore

Electrical Engineering

This project combines the advantages of high efficiency of power electronics with the existing high fidelity of audio amplifiers. The result will be functionally equivalent to existing amplifiers but will use considerably less energy. A complete system was designed, simulated, built and tested in a period of three quarters. The end result is an amplifier that functions, but would not be suitable for commercial marketing. Suggestions to improve the performance are provided.

Multipolymer Interactions In Bulk Heterojunction Photovoltaic Devices, Grant Olson

Physics

Multipolymer photovoltaics, single layer devices made up of multiple photoactive polymers, can create organic photovoltaics (OPVs) with a wider spectral response than single polymer systems without the difficult fabrication of a tandem. Our group has successfully created multipolymer solar devices with 2% power conversion efficiency. We have analyzed the optical and electrical properties of these devices, and found that it may be possible for polymers to assist each other with charge extraction, though combining polymers disrupts single polymer crystallinity.

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …

A Proposed Control Solution For The Cal Poly Wind Energy Capture System, Kent R. Burnett

Master's Theses

The focus of this thesis is to research, analyze, and design a reliable and economical control system for the Cal Poly Wind Energy Capture System (WECS). A dynamic permanent magnet generator model is adopted from [1] and [2] and combined with an existing wind turbine model to create a non-linear time varying model in MATLAB. The model is then used to analyze potentially harmful electrical disturbances, and to define safe operating limits for the WECS. An optimal operating point controller utilizing a PID speed loop is designed with combined optimization criteria and the final controller design …

Evaluation Of A Novel Axial Flux Variable Reluctance Machine, Derek Braden Hines

Master's Theses

The objective of this thesis is to determine the feasibility of a novel axial flux variable reluctance machine design. The design aims to compete with prevalent rare-earth permanent magnet machines while also implementing an innovative torque ripple minimization strategy. Given the fundamental operating principles, a selection of dimensions, materials, and excitations are prepared for the machine. Special attention is given to the rotor profile which is crucial to operation. Finite element analysis software is used to evaluate a three-dimensional model in terms of inductance and torque. The ultimate potential of the machine is discussed and recommendations for improvement are proposed.

Pattern Recognition Of Power System Voltage Stability Using Statistical And Algorithmic Methods, Varun Togiti

LSU New Orleans Theses and Dissertations

In recent years, power demands around the world and particularly in North America increased rapidly due to increase in customer’s demand, while the development in transmission system is rather slow. This stresses the present transmission system and voltage stability becomes an important issue in this regard. Pattern recognition in conjunction with voltage stability analysis could be an effective tool to solve this problem

In this thesis, a methodology to detect the voltage stability ahead of time is presented. Dynamic simulation software PSS/E is used to simulate voltage stable and unstable cases, these cases are used to train and test the …

A Study On The Effects Of Solar Power, Jonathan Hayes

Electrical Engineering Undergraduate Honors Theses

The utilization of new and alternative energy sources, specifically solar energy, has been on the rise and will continue to grow as we attempt to diminish our use and dependency on older, nonrenewable energy sources. One of the biggest challenges involved with the use of solar energy, or renewable energy in general, is how to provide this energy for general public use. Some of the limiting factors to this are the efficiency in which solar power can be harvested and converted into usable energy, and the cost of the technology to do this. Recent technological developments have included the microinverter, …