Power and Energy Commons^™

Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang

Journal of Electrochemistry

In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …

Microemulsion Preparation And Electrochemical Characterization Of Pt/C，Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui

Journal of Electrochemistry

The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.

Preparation And Characterization Of The Lani0.6fe0.4o3-Δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu

Journal of Electrochemistry

The LaNi0.6Fe0.4O3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi0.6Fe0.4O3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi0.6Fe0.4O3-δ/ScSZ/LaNi0.6Fe0.4O3-δ sintered at 1050°C was the smallest (0.70Ω?cm2, 0.27Ω?cm2 and 0.12Ω?cm2 at 750°C, 800°C and 850°C, respectively). In the presence of the Fe-Cr alloy interconnection at 750°C, the cathode performance showed that, with …

Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang

Journal of Electrochemistry

The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm2 in Fe(Ⅲ)-oxalate-calcium gluconate system.

Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2o2 On Gew11co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng

Journal of Electrochemistry

The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …

Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li

Journal of Electrochemistry

The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …

Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman

Master's Theses

Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.

Synthesis of A-site deficient [A=0.97] Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ (BSCF) was …

Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries, Xin Yang, Xue-Wu Liu, Gui-Chang Liu, Zhi-Cong Shi, Xin Li, Guo-Hua Chen

Journal of Electrochemistry

The LiMnPO4/C composites were prepared using a solid-state reaction with addition of the resorcinol formaldehyde resin as the carbon source. The effects of reaction temperature and time on the crystal structure, morphology and electrochemical properties of the LiMnPO4/C composites were investigated. The results show that the best performance was achieved with the LiMnPO4/C composites synthesized at 600 oC for 12 h which had the particle sizes about 100~200 nm. The initial discharge capacities were 121.6 mAh?g-1 at 0.02C, 110 mAh?g-1 at 0.1C and more than 60 mAh?g-1 at 1C. An overall reversible capacity of 110 mAh?g-1 had been retained after …

Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO2 particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO2 in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.

Synthesis And Electrochemical Behaviors Of Li2coxmn1-Xsio4 As A Cathode Material For Lithium-Ion Batteries, Lin Wang, Dong-Ping Lv, Yong Yang

Journal of Electrochemistry

We have successfully synthesized Li2CoxMn1-xSiO4/C (x=0, 0.1, 0.3, 0.5, 1)/C composites using hydrothermal assisted sol-gel process and ball-milling method. The results of X-ray diffraction show that the solid solutions of Li2CoxMn1-xSiO4 can be achieved when x≤0.3. The initial capacities increase from 70 mAhg-1??? of Li2MnSiO4/C to 105 mAhg-1??? of Li2Co0.3Mn0.7SiO4/C. Cyclic Voltammetry (CV) curves show that the replacement of Mn with Co can reduce the electrochemical polarization, making the insertion-extraction reaction of Li+ much easier. EIS results also prove that Co can decrease the charge transfer impedance of the materials.

Vuv Absorption Cross Section Of Benzene, Relevance For Titan’S Atmosphere, F-J. Capalbo, Y. Bénilan, N. Fray, M. Schwell, Et. Es-Sebbar, N. Champion, T. Koskinen, R. Yelle

Dr. Et-touhami Es-sebbar

Saturn's largest satellite, Titan, is the only one in the Solar System known to have a thick N2/CH4, planet like atmosphere. The dissociation of these principal components and the recombination of the products make this atmosphere to be rich in organic compounds of high interest for astrobiology. Solar and stellar occultations observed by the Ultraviolet Imaging Spectrograph (UVIS) on board the Cassini spacecraft can be used to characterize the composition of Titan’s upper atmosphere (400 – 1400 km). The results depend strongly on the knowledge of the molecular absorption cross sections of the atmospheric constituents (Ferradaz et al. 2009). This …

Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation, Su-Dong Yang, Yan-Yu Liang, Zhu-Liang Wen, Qi-Jun Song, Xiao-Gang Zhang

Journal of Electrochemistry

Graphite oxide (GO) was prepared from by Hummers method. Then the graphene nanosheets supporting Pd catalysts were prepared by a single-step chemical reduction method. The electrocatalytic performance for formic acid oxidation of the prepared Pd/graphene composite was studied as an electrode material in comparison with the composite catalysts based on the other carbons (MWCNTs, SWCNTs, and Vulcan XC-72 carbon black). X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements indicated that the Pd nanoparticles were well dispersed on the surface of the graphene nanosheets with a small particle size. The electrocatalytic oxidation of formic acid was studied by electrochemically active …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H2O2 with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 μmol?L-1 to 1.0 …

Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation, Ye Chen, Wen-Li Zhao, Qing Wen

Journal of Electrochemistry

Ti-base manganese dioxide (Ti/MnO2) electrode was prepared by anodically electrodeposition technology in this paper. The structure of the electrode, the microstructure of the electrode surface and the element composition of the electrode were analyzed by XRD, SEM and EDS. The preparation process parameters of the electrode were studied in detail with the help of the V~logi curve and phenol degradation curve. The Ti/MnO2 electrode was anodically electrodeposited at current density 4mA•cm-2, the Mn2 + ions concentration 0.5mol•L-1 and temperature70℃. The V~logi curve and phenol degradation curve were used to evaluate electrocatalytic oxidization properties of the electrode with phenol as the …

Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma

Journal of Electrochemistry

University of Technology, Hangzhou 310032, Zhejiang,China)
Abstract: The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when …

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO2 reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO2 reduction on Cu(111) surface are CO2(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH2O* → (CH2 + O)*, CH2* + 2H* → CH4 or 2CH2* → C2H4. On Cu(111) surface, the reaction rate is controlled by steps of CH2O* → (CH2 + O)*, CO2(g) + H* → COOH → (CO +OH)* and (CO + H)* → CHO*. In addition, the …

Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides, Zhen-Sheng Yang, Ling-Bin Kong, Li Deng, Yong-Chun Luo, Long Kang

Journal of Electrochemistry

By using defects on the surface of CMK-3 served as nucleation center, Co0.25Ni0.75 oxide/C composite was successfully prepared through a simple chemical co-precipitation method. Characterization was carried by using X-ray diffraction, BET and scanning electron microscopy. Results showed that a perfect mesoporous network of interconnected nanoflakes was obtained for Co0.25Ni0.75 oxide/C composite and, this material has a less crystallization, interconnected nanoflakes network structure and a narrow mesoporous distribution at about 3~4 nm. The highly dispersed and loosely packed Co0.25Ni0.75 oxide/C composite possessed good electrochemical accessibility and fast diffusion rate of OH-. Cyclic voltammetry, charge–discharge curves suggested that the as-prepared Co0.25Ni0.75 …

Transferts De Chaleur Dans Un Réacteur Thermochimique Solaire Muni D’Un Récepteur Volumique Poreux, Hernando Romero Paredes Rubio

Hernando Romero Paredes Rubio

Un réacteur thermochimique solaire de 1 kW muni d’une structure céramique poreuse en céramique est modélisé pour simuler les transferts thermiques a l’intérieur du récepteur volumétrique. Le modèle développé a été utilisé pour prévoir le comportement thermique du réacteur en fonction des différentes conditions opératoires qui concernent le débit de gaz inerte, le flux solaire incident, la porosité, la longueur du récepteur, et la prise en compte de réactions chimiques. Les résultats montrent que la température maximale est de 1850K pour une concentration solaire de 1000 soleils. La température diminue de manière significative lorsque le débit de gaz augmente. Un …

Characterization Of Continuous Vacuum Ultraviolet Lamps-Implication On The Study Of Methane Photolysis At Lyman Alpha (121.6 Nm), M-C. Gazeau, Y. Benilan, Et. Es-Sebbar, A. Jolly, E. Arzoumanian, N. Fray, H. Cottin

Dr. Et-touhami Es-sebbar

Low-temperature hydrogen plasmas are widely used as continuous vacuum ultraviolet irradiation sources in photochemical studies and, in particular, in laboratory simulations of planetary atmospheres. One of the most challenging objectives of such experiments is to retrieve accurate quantitative laboratory data allowing a reliable comparison with theoretical and/or observational ones. This task can only be achieved when the irradiation source delivers a well characterised radiation in terms of flux and wavelength dependency. As an example, we will present a study, developed in the frame of a program dedicated to simulations of Titan’s atmosphere, on methane photolysis at Lyman alpha (121.6 nm). …

Formation Of Hcn And Nh3 As Primary Compounds Of Titan’S Atmosphere Simulations Using N2-Ch4 Afterglow Plasma’’, M-C. Gazeau, Y. Bénilan, E. Arzoumanian, Et. Es-Sebbar, A. Jolly, C.D. Pintassilgo

Dr. Et-touhami Es-sebbar

No abstract provided.

Electrocatalytic Oxidation Of Hydrazine At Rutin Carbon Nanotubes Modified Electrode, Hong-Fang Zhang, Qing-Lin Sheng, Jian-Bin Zheng

Journal of Electrochemistry

The electrochemical behavior and electrocatalytic oxidation of hydrazine on rutin multiwall carbon nanotubes modified glassy carbon electrode were studied by cyclic voltammetry.The experimental results indicated that the electrode exhibits good electrocatalytic activity to hydrazine at a reduced oxidation potential of 262 mV.The amperometric response of the modified electrode showed linear increase after successive addition of hydrazine in the concentration range of 2.5×10-6~1.0×10-4 mol·L-1 with a detection limit of 5×10-7 mol·L-1.

Electrochemical Deposition Of Zinc Oxide Crystal Whiskers, Peng-Zeng Lu, Su Li, Jin-Qian Jia, Zhen-Hai Liang

Journal of Electrochemistry

Pine needle ZnO crystal whiskers were electrodeposited by anodization of zinc foil.The crystal whiskers were characterized by scanning electron microscopy(SEM) and X-ray diffraction(XRD) spectroscopy.The results show that the lengths and diameters of ZnO crystal whiskers are 200~300 nm and 20~50 nm,respectively,with the ratio of the length to diameter ranging from 10~15.The whiskers belong to wurtzite ZnO(JCPDS 36-1451) with good crystallinity and high purity.The crystalization behavior of ZnO was studied by cyclic voltammetry.The effects of the surface oxide layer at the zinc substrates and the [Zn(OH)4]2-concentration of the aqueous electrolyte on the formation of zinc oxide whiskers were investigated.

Synthesis Of Mesoporous Nickel Oxide For Supercapacitor Application, Xuan-Xuan Chen, Zhen-Zhen Zhao, Deng-Chao Wang, Zhong-Jie Huang, Wen-Bin Ni, Li Yu, Jian-Wei Zhao

Journal of Electrochemistry

Mesoporous nickel oxide has been synthesized by calcining metal-organic coordination precursor.Transmission electron microscopy and BET test showed that the prepared NiO had a regular morphology and displayed a narrow size distribution.Electrochemical tests revealed that such mesoporous NiO had a specific capacity of 72 F·g-1 at the current of 2.0 A·g-1.Futhermore,the material showed excellent cycle-life stability.There was no degradation of capacitance after 1000 cycles.

A Titanium-Supported Nanoporous Pd Electrocatalyst For Methanol Oxidation, Feng-Juan Niu, Qing-Feng Yi

Journal of Electrochemistry

Titanium-supported nanoporous palladium electrode(nanoPd /Ti) was prepared by a hydrothermal process in the presence of the ligand EDTA and using formaldehyde as reducing agent.SEM images showed that the size of Pd particles was about 60 nm and the Pd particles were connected with each other to form a three-dimensional network structure.Cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) were applied to evaluate the electrocatalytic activity of the nanoPd/Ti electrode towards methanol oxidation in alkaline solution.CV results showed that the nanoPd /Ti electrode presented high anodic peak densities and a low onset potential for methanol oxidation.Also nanoPd /Ti electrode showed excellent CO tolerance …

Electrooxidation Of Methanol On Multilayer Films Of Polypyrrole-Platinum Electrode, Ling Zhang, Long-Zhen Zheng

Journal of Electrochemistry

Multilayer films of polypyrrole-platinum electrode were fabricated by cyclic voltammetric technique.Electro-oxidation of methanol on this electrode was investigated with the aid of cyclic voltammetry and chronoamperometry.Results demonstrated that the multilayer of polypyrrole-platinum electrode behaved better electrocatalytic performance for electro-oxidaton of methanol and better poison resistant.Furthermore,with the increase of deposited platinum loadings,the rate controlling step on electro-oxidation reaction of methanol was changed from CO oxidation to sorption-desorption of hydrogen.

Novel Anion Exchange Membranes Base On Copolymer Of 2-(Diethylamino) Ethyl Methacrylate And Fluoro-Polyacrylate For Alkaline Direct Methanol Fuel Cells, Yan-Mei Zhang, Jun Fang, Ge Yan, Yong-Ze Zhuang

Journal of Electrochemistry

Anion exchange membrane fuel cells,which use anion exchange membranes as polyelectrolytes,have attracted more and more research interests recently.In this work,a series of hydroxyl-conducting anion-exchange membranes based on the copolymer of 2-(Diethylamino)ethyl methacrylate and fluoro-polyacrylate were prepared by radical polymerization,and their potential applications in alkaline fuel cells were assessed.It was shown that the ionic conductivity of the membranes reached 10-2 S·cm-1 at room temperature,while the methanol permeability was lower than 10-7 cm2·s-1.The maximum power density of fuel cell assembled with this membrane was achieved to be 43.2 mW·cm-2 at room temperature,indicating possible application of this membrane in alkaline fuel cells.

Using Thermally Coupled Reactive Distillation Columns In Biodiesel Production, Nghi Nguyen, Yaşar Demirel

Yaşar Demirel Publications

Production of ethyl dodecanoate (biodiesel) using lauric acid and methanol with a solid acid catalyst of sulfated zirconia is studied by using two distillation sequences. In the first sequence, the methanol recovery column follows the reactive distillation column. In the second sequence, the reactive distillation and methanol recovery columns are thermally coupled. Thermally coupled distillation sequences may consume less energy by allowing interconnecting vapor and liquid streams between the two columns to elminate reboiler or condenser or both. Here we study the thermally coupled side-stripper reactive distillation and eliminate the condenser of the reactive distillation column. Both the sequences are …