Power and Energy Commons^™

Arc Fault Circuit Interrupter Development For Residential Dc Electricity, Cassidy Alan Aarstad

Master's Theses

The following technical report describes the development and testing of an arc fault circuit interrupter (AFCI) for DC circuits operating primarily at 48 volts. We have identified an effective method for determining when arcing is occurring. Our method is primarily based on comparing the frequency spectrum of current flowing through the circuit during an arcing event to a known characteristic spectrum. Once an arc has been identified, our interrupter is capable of responding adequately to eliminate the arc. Hardware tests show the AFCI developed in this thesis responded, in all test cases, within 2 seconds of an arc fault occurrence. …

Low-Frequency Series Loaded Resonant Inverter Characterization, Alfredo Medina

Master's Theses

Modern power systems require multiple conversions between DC and AC to deliver power from renewable energy sources. Recent growth in DC loads result in increased system costs and reduced efficiency, due to redundant conversions. Advances in DC microgrid systems demonstrate superior performance by reducing conversion stages. The literature reveals practical DC microgrid systems composed of wind and solar power to replace existing fossil fuel technologies for residential consumers. Although higher efficiencies are achieved, some household appliances require AC power; thus, the need for highly efficient DC to AC converters is imperative in establishing DC microgrid systems. Resonant inverter topologies exhibit …

Wide-Band Gap Devices For Dc Breaker Applications, Olukayode O. Sodipe

Master's Theses

With the increasing interest in wide-band gap devices, their potential benefits in power applications have been studied and explored with numerous studies conducted for both SiC and GaN devices. This thesis investigates the use of wide-band gap devices as the switching element in a semiconductor DC breaker. It involves the design of an efficient semiconductor DC breaker, its simulation in SPICE, construction of a hardware prototype and the comparative study of SiC and Si versions of the aforementioned breaker. The results obtained from the experiments conducted in the process of concluding this thesis show that the SiC version of the …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

Adaptive Automotive Lighting Systems, Marc W. Haeberlin

Master's Theses

Over the past few years, the use of LEDs within the automotive and avionic industries has increased due to their high efficiency, durability and wide range of light brightness. As the use of LEDs within these industries grows, a need for reliable, high performance drivers becomes more relevant. Companies are implementing LEDs for applications involving adaptive lighting or simple dimming features. This thesis shows implementation of various non-isolated analog converters integrated with digital dimmers to achieve these adaptive lighting systems. Adaptive lighting systems involve reading an input from an external source (brake pedal or steering wheel) and changing the brightness …

Universal Programmable Battery Charger With Optional Battery Management System, Michael Duke Desando

Master's Theses

This report demonstrates improvements made in battery charging and battery management technology through the design of a universal programmable battery charger with optional battery management system attachment. This charger offers improvements in charge efficiency and unique battery charging algorithms to charge a variety of battery chemistries with variety of power requirements. Improvements in efficiency result from a synchronous Buck Controller topology as compared to previous universal chargers that use asynchronous Buck-Boost Converter topologies. This battery charger also surpasses current universal battery chargers by offering different charge modes for different battery chemistries. Charge modes provide the user an option between extending …

Three-Phase Generation Using Reactive Networks, Tattiana Karina Coleman Davenport

Master's Theses

Household appliances utilize single-phase motors to perform everyday jobs whether it is to run a fan in an air conditioner or the compressor in a refrigerator. With the movement of the world going “green” and trying to make everything more efficient, it is a logical step to start with the items that we use every day. This can be done by replacing single-phase motors with three-phase motors in household appliances. Three-phase motors are 14% more efficient than single-phase motors when running at full load and typically cost less over a large range of sizes [1]. One major downside of incorporating …

A Low-Cost Loop Measurement Tool For Dc-Dc Converters, Shouee B. Lin

Master's Theses

Loop measurements are very important in evaluating dynamic performance of DC-DC converters. In this thesis, a small loop measurement tool as a low-cost alternative to a network analyzer is proposed. The tool is particularly useful when a network analyzer is not always available for use, for example when engineers are working on-site with customers or when a network analyzer is not affordable due to their relatively high cost. The design, simulation, and hardware implementation of the inexpensive loop measurement tool will be presented in this thesis. Results from computer simulation and hardware prototype demonstrate the ability of the proposed tool …

Grid-Scale Energy Storage: A Proposed Control Algorithm For Sodium Sulfur Batteries, Daniel Spaizman

Master's Theses

With carbon dioxide levels in our atmosphere reaching record highs and 2020 quickly approaching, California is expected to pave the way for the United States in terms of replacing fossil fuel generation facilities with various renewable energy power plants. It is well documented that the inherent variability and limited duty cycle of renewables has hindered their growth. Energy storage technologies represent the bridge that can help us cross the divide from where we stand to where we must stand in the next 6 years. Utility companies value services such as peak shaving, voltage support, and frequency regulation, all of which …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

Dual High-Voltage Power Supply For Use On Board A Cubesat, Nicholas Weiser

Master's Theses

Since their conception in 1999, CubeSats have come and gone a long way. The first few that went into space were more of a “proof of concept,” and were more focused on sending simple data and photographs back to Earth. Since then, vast improvements have been made by over 40 universities and private firms, and now CubeSats are beginning to look towards interplanetary travel. These small satellites could provide a cost effective means of exploring the galaxy, using off the shelf components and piggy-backing on other launch vehicles with more expensive payloads. However, CubeSats are traditionally launched into Low Earth …

Improvements To A Bi-Directional Flyback Dc-Dc Converter For Battery System Of The Dc House Project, Michael Wu

Master's Theses

The DC House project relies primarily on renewable energy sources to provide DC power to the various loads of the house. However, not all renewable sources are capable of providing power at all times of the day. A back-up energy source in the form of a battery storage system must be available to meet the electrical needs of the house. A bi-directional flyback power converter was initially designed to allow a battery to charge from as well as discharge to the 48V bus line of the DC House. The design provided a 35W prototype to demonstrate the converter’s feasibility. Further …

Modeling And Simulation Of Parallel D-Statcoms With Full-Wave Rectifiers, Jason Brinsfield

Master's Theses

In recent years, both a significant increase in electrical demand and a large influx of intermittent renewable energy sources have put a considerable stress on the nation’s electrical grid. Conventional power flow control techniques such as capacitor banks and tap-changing transformers are incapable of adequately handling the rapid fluctuations in power supply and demand that today’s grid experiences. Flexible AC Transmission System (FACTS) controllers are a practical way to compensate for such rapid power fluctuations. One type of shunt FACTS controller is the Static Synchronous Compensator (STATCOM), which uses fully controllable switches to source or sink reactive power to a …

System Design Considerations And The Feasibility Of Passively Compensated, Permanent Magnet, Iron-Core Compulsators To Power Small Railgun Platforms, Collin Taylor Macgregor

Master's Theses

This thesis provides insight into the different aspects of compulsator design for use with railgun systems. Specifically, the design space is explored for passively compensated, permanent magnet iron-core compulsators. Seven design parameters are varied within a compulsator model developed for the Cal Poly Compulsator (CPCPA). The Matlab code for this model is included within the appendix. Efforts were made to compare and validate this compulsator model to published data from existing systems. The compulsator model was found to match closely with discharge pulse length, but resulted in lower values for peak current and projectile velocity by 50% and 30% respectively …

Multiple Input Single Output (Miso) Tablet/ Phone Charger, Kevin Wong

Master's Theses

This thesis entails the design and implementation of a multiple input single output (MISO) DC-DC converter using the flyback topology to charge tablets/ smartphones or any USB powered portable device. The MISO converter will enable the use of various renewable energy sources such as a solar panel/ rechargeable battery combination, bicycle dynamo, hydroelectric power, and wind turbine. This paper will cover the design, simulations, and test results of the MISO converter. The flyback topology was chosen due to its low part count and its efficiency at low power. The proposed converter has a nominal 12V input to output USB 2.0 …

Designing Anti-Islanding Detection Using The Synchrophasor Vector Processor, Ruth Christiana Huang

Master's Theses

ABSTRACT

Designing Anti-Islanding Detection Using the Synchrophasor Vector Processor

Ruth Huang

The need for distributed generation (DG) has become more and more popular because of the adverse effects of fossil fuels and the fear of running out of fossil fuels. By having DG, there are less transmission losses, voltage support, controllability of the system, decreased costs in transmission and distribution, power quality improvement, energy efficiency, and reduced reserve margin. The adverse effects of DG are voltage flicker, harmonics, and islanding. Islanding occurs when the DG continues to energize the power system when the main utility is disconnected. Detecting islanding is …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Impact Of Photovoltaic System Penetration On The Operation Of Voltage Regulator Equipment, Abesh Sorab Mubaraki

Master's Theses

The growing popularity of photovoltaic (PV) generation systems leads to an increase in the number of residential and commercial grid-tied PV systems that interconnect to the distribution circuit. This affects the characteristics of the distribution circuit; for example, the assumption that the voltage profile of a radial line decreases down-stream becomes invalid because of the addition of the PV system on the line. This poses new challenges when setting the parameters of voltage regulating devices. Add to that the fact that PV systems are intermittent, especially on cloudy days, which make the line even more difficult to regulate, and the …

The Bicycle-Powered Smartphone Charger, Chris Arntzen

Master's Theses

This thesis entails the design and fabrication of a smartphone charger that is powered by a bicycle dynamo hub. In addition to the design and validation of the charger prototype, this thesis involves the testing and characterization of the dynamo hub power source, the design and construction of specialized test equipment, and the design and prototyping of a handlebar-mounted case for the smartphone and charging electronics. With the intention of making the device a commercial product, price, aesthetics, and marketability are of importance to the design. An appropriate description of the charger circuit is a microcontroller-based energy management system, tailored …

Bi-Directional Flyback Dc-Dc Converter For Battery System Of The Dc House Project, Austin J. Luan

Master's Theses

The DC House project strongly relies on renewable energy sources to provide power to the house for various loads. However, when these sources are unable to provide power at a certain time, a back-up energy source from a battery must be readily available to fulfill the house’s power needs. This thesis proposes a bi-directional flyback power converter to allow a single-stage power path to charge the battery from and to discharge the battery to the DC House 48 V system bus. The design, simulation, and hardware prototype of the proposed flyback bi-directional converter will be conducted to demonstrate its feasibility. …

Design Of Portable Dc Light Bulb For The Dc House Project, Jan Marvin Perez Macairan

Master's Theses

This thesis focuses on the design and implementation of the Portable DC Light Bulb system for Cal Poly San Luis Obispo’s DC House Project. The DC Portable Light Bulb highlights the NiMH battery charging circuit, buck converter, and boost converter. The system is intended as a flashlight adaptor placed in between the dimmable DC light bulb and its screw base. The adaptor adds a portability feature to the DC light bulb to provide lighting wherever the user pleases. The Portable DC Light Bulb system is designed to operate with an input range of 24V-60V and regulate an output voltage of …

Voltage Stability Analysis Using Simulated Synchrophasor Measurements, Allan Agatep

Master's Theses

An increase in demand for electric power has forced utility transmission systems to continuously operate under stressed conditions, which are close to instability limits. Operating power systems under such conditions along with inadequate reactive power reserves initiates a sequence of voltage instability points and can ultimately lead to a system voltage collapse. Significant research have been focused on time-synchronized measurements of power systems which can be used to frequently determine the state of a power system and can lead to a more robust protection, control and operation performance. This thesis discusses the applicability of two voltage stability synchrophasor-based indices from …

Modeling And Analysis Of A Dynamic Voltage Regulator, Timothy David Haskell

Master's Theses

Increased government funding and incentives in recent years has led to an increase in the number of grid-tied renewable energy sources as their economic benefits become more renowned. Unfortunately, the outputs of these renewable resources are often highly variable, resulting in undesirable voltage disruptions that are harmful to sensitive loads. In addition to the energy variability of renewable energy sources, random voltage sags, swells and disruptions are already a major issue in power systems. Recent advances in power electronic devices have provided a platform for new solutions to the voltage support problem in power systems. One promising solution is the …

Modeling And Analysis Of A Pv Grid-Tied Smart Inverter's Support Functions, Benjamin Anders Johnson

Master's Theses

The general trends in the past decade of increasing solar cell efficiency, decreasing PV system costs, increasing government incentive programs, and several other factors have all combined synergistically to reduce the barriers of entry for PV systems to enter the market and expand their contribution to the global energy portfolio. The shortcomings of current inverter functions which link PV systems to the utility network are becoming transparent as PV penetration levels continue to increase. The solution this thesis proposes is an approach to control the inverters real and reactive power output to help eliminate the problems associated with PV systems …

Condition-Dependent Risk Assessment Of Large-Scale Grid-Tied Photovoltaic Power Systems, Sherwin Li

Master's Theses

This thesis reviews the methods for evaluating the reliability of large PV systems and techniques for quantifying the impacts of PV interconnection on distribution system reliability. In addition, a comparative study is performed to evaluate the seasonal condition-dependent risk performance of central-inverter and string-inverter grid-tied PV power systems. Major contributions include: 1) risk analysis of seasonal impacts for string and centralized PV systems. Seasonal sensitivities of PV system risks to system structures, temperature variation, solar insolation, and capacitor equivalent series resistance are analyzed; and 2) the incorporation of the effect of operational conditions and the aging failure model into the …

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Development And Implementation Of A Calibration Procedure For Complex Impedance Spectrum Measurements With Applications To Embedded Battery Health Monitoring And Management Systems, William H. Morrison

Master's Theses

Energy storage devices such as rechargeable Lithium ion batteries are assuming an increasingly prominent role in society, covering applications from electric / hybrid electric vehicles to personal portable electronics. In response to this increasing demand, technologies that monitor battery health and remaining useful life have developed. One such system is the Smart Battery Status Monitor (SBSM), developed by the Idaho National Laboratory, Montana Tech and Qualtech Systems, Inc. The SBSM utilizes impedance spectrum measurements using a subsystem called the Impedance Measurement Box (IMB). The impedance measurements are complex quantities (having both a resistive and a reactive component) and are made …

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …

A Proposed Control Solution For The Cal Poly Wind Energy Capture System, Kent R. Burnett

Master's Theses

The focus of this thesis is to research, analyze, and design a reliable and economical control system for the Cal Poly Wind Energy Capture System (WECS). A dynamic permanent magnet generator model is adopted from [1] and [2] and combined with an existing wind turbine model to create a non-linear time varying model in MATLAB. The model is then used to analyze potentially harmful electrical disturbances, and to define safe operating limits for the WECS. An optimal operating point controller utilizing a PID speed loop is designed with combined optimization criteria and the final controller design …

Evaluation Of A Novel Axial Flux Variable Reluctance Machine, Derek Braden Hines

Master's Theses

The objective of this thesis is to determine the feasibility of a novel axial flux variable reluctance machine design. The design aims to compete with prevalent rare-earth permanent magnet machines while also implementing an innovative torque ripple minimization strategy. Given the fundamental operating principles, a selection of dimensions, materials, and excitations are prepared for the machine. Special attention is given to the rotor profile which is crucial to operation. Finite element analysis software is used to evaluate a three-dimensional model in terms of inductance and torque. The ultimate potential of the machine is discussed and recommendations for improvement are proposed.