Power and Energy Commons^™

Surface And Interface Properties In Thin-Film Solar Cells: Using Soft X-Rays And Electrons To Unravel The Electronic And Chemical Structure, Lothar Weinhardt, Dirk Hauschild, Clemens Heske

Chemistry and Biochemistry Faculty Research

Thin‐film solar cells have great potential to overtake the currently dominant silicon‐based solar cell technologies in a strongly growing market. Such thin‐film devices consist of a multilayer structure, for which charge‐carrier transport across interfaces plays a crucial role in minimizing the associated recombination losses and achieving high solar conversion efficiencies. Further development can strongly profit from a high‐level characterization that gives a local, electronic, and chemical picture of the interface properties, which allows for an insight‐driven optimization. Herein, the authors' recent progress of applying a “toolbox” of high‐level laboratory‐ and synchrotron‐based electron and soft X‐ray spectroscopies to characterize the chemical …

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Energy Efficiency Evaluation Of Blower Heater Non-Purge Compressed Air Dryers, Alexandra M. Botts

Graduate Theses, Dissertations, and Problem Reports (ETD)

There are several compressed air dryers available for industrial use including, refrigerant, desiccant, and membrane. This research focuses on twin tower regenerative closed loop desiccant dryers, specifically: blower heater non-purge (BHNP) with and without cooling water pumps, Compressed-air Heater Purge (CHP), Blower Heater Purge (BHP), and Pressure Swing Heaterless (PSH). These styles of dryers are used mainly in industries that require extremely dry air such as, food manufacturing, medical air, or sensitive technology manufacturers. The research was conducted by collecting and analyzing real time current draw data on air compressors and associated dryers at eight different facilities (13 compressor systems) …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Optimal Placement Of Distributed Energy Storage Systems In Distribution Networks Using Artificial Bee Colony Algorithm, Choton K. Das, Octavian Bass, Ganesh Kothapalli, Thair S. Mahmoud, Daryoush Habibi

Research outputs 2014 to 2021

The deployment of utility-scale energy storage systems (ESSs) can be a significant avenue for improving the performance of distribution networks. An optimally placed ESS can reduce power losses and line loading, mitigate peak network demand, improve voltage profile, and in some cases contribute to the network fault level diagnosis. This paper proposes a strategy for optimal placement of distributed ESSs in distribution networks to minimize voltage deviation, line loading, and power losses. The optimal placement of distributed ESSs is investigated in a medium voltage IEEE-33 bus distribution system, which is influenced by a high penetration of renewable (solar and wind) …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Intelligent Application Of Flexible Ac Transmission System Components In An Evolving Power Grid, Robert Wall

Graduate Theses and Dissertations

The world revolves around energy and the energy sector is continually transforming and evolving. The status quo has been set by governing agencies in the United States for completely reliable power. The demand for energy efficiency continually rises for multiple reasons. Technology has improved for all sectors of the power grid, including renewable energy sources, fault protection, and SMART grid technology. The addition of new energy sources has led to the decommissioning of inefficient energy sources. The implementation of new technologies and power load on a large scale, coupled with the removal of grid stabilizers has posed different challenges that …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Cfd Modeling On Hydrodynamic Characteristics Of Multiphase Counter-Current Flow In A Structured Packed Bed For Post-Combustion Co2 Capture, Li Yang, Fang Liu, Kozo Saito, Kunlei Liu

Mechanical Engineering Faculty Publications

Solvent-based post combustion CO₂ capture is a promising technology for industrial application. Gas-liquid interfaces and interactions in the packed bed are considered one of the key factors affecting the overall CO₂ absorption rate. Understanding the hydrodynamic characterizations within packed beds is essential to identify the appropriate enhanced mass transfer technique. However, multiphase counter-current flows in the structured packing typically used in these processes are complicated to visualize and optimize experimentally. In this paper, we aim to develop a comprehensive 3D multiphase, counter-current flow model to study the liquid/gas behavior on the surface of structured packing. The output from …

Electrochemical Hydrogenation Of Acetone To Produce Isopropanol Using A Polymer Electrolyte Membrane Reactor, Chen Li, Ashanti M. Sallee, Xiaoyu Zhang, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

Electrochemical hydrogenation (ECH) of acetone is a relatively new method to produce isopropanol. It provides an alternative way of upgrading bio-fuels with less energy consumption and chemical waste as compared to conventional methods. In this paper, Polymer Electrolyte Membrane Fuel Cell (PEMFC) hardware was used as an electrochemical reactor to hydrogenate acetone to produce isopropanol and diisopropyl ether as a byproduct. High current efficiency (59.7%) and selectivity (>90%) were achieved, while ECH was carried out in mild conditions (65 degrees C and atmospheric pressure). Various operating parameters were evaluated to determine their effects on the yield of acetone and …

Interface Model Of Pem Fuel Cell Membrane Steady-Dtate Behavior, Russell L. Edwards, Ayodeji Demuren

Mechanical & Aerospace Engineering Faculty Publications

Modeling works which simulate the proton-exchange membrane fuel cell with the computational fluid dynamics approach involve the simultaneous solution of multiple, interconnected physics equations for fluid flows, heat transport, electrochemical reactions, and both protonic and electronic conduction. Modeling efforts vary by how they treat the physics within and adjacent to the membrane-electrode assembly (MEA). Certain approaches treat the MEA not as part of the computational domain, but rather an interface connecting the anode and cathode computational domains. These approaches may lack the ability to consistently model catalyst layer losses and MEA ohmic resistance. This work presents an upgraded interface formulation …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Low Voltage Ride Through Enhancement For Wind Turbines Equipped With Dfig Under Symmetrical Grid Faults, Francis Mwasilu

Tanzania Journal of Engineering and Technology (TJET)

In modern power systems with significant penetration of wind-turbines (WTs), improvement of low voltage ride through (LVRT) capability of WTs equipped with doubly-fed induction generators (DFIGs) is an important issue. Thus, this paper proposes a low voltage ride through (LVRT) strategy, which comprise of a capacitor connected in series with an inductor both connected in parallel to a resistor. The configuration is then connected to a small series resistor via a pair of antiparallel-Thyristors. The circuit and its switching control scheme of the proposed LVRT circuit are designed to: minimize the transition times, maintain the RSC connection to the rotor-windings, …

Perovskite Solar Cells Fabricated Via Scalable Dip Coating Methods, Joseph F. Iannello

Theses and Dissertations

Perovskite solar cells present the possibility for less expensive electricity generation, through the use of low cost materials and fabrication methods relative to current silicon-based technology. Many current methods of fabricating thin film perovskite solar cells focus on spin-coating, which inherently lacks scalability due to particle conglomeration, poor uniformity over a larger area, and safety concerns. Dip-coating, an alternative to spin-coating, which is explored here addresses these issues which limit scalability. Each individual layer can be separately synthesized, deposited, and characterized, which leads towards scalability. Choosing only the best results from each independent layer allowed progress to the creation of …

A Human Powered Micro-Generator For Charging Electronic Devices, John Adam

Senior Theses

A hand-pulled generator has been designed and tested. A preliminary result has been obtained and discussed. This device was created to provide outlet-free charging. Electronic devices are useful when going out into the wilderness. A portable power supply is necessary to keep an electronic device alive. This project created a device that converts human energy into electricity to charge electronic devices. This thesis overviews the device’s design, build, and tests. Two different tests were run to determine that the device is capable of charging the storage battery. The device presented can provide 14 minutes of charging time with one hour …

Measuring The Double Layer Capacitance Of Electrolyte Solutions Using A Graphene Field Effect Transistor, Agatha Ulibarri

Senior Theses

When operating graphene field effect transistors (GFETs) in fluid, a double layer capacitance (C_dl) is formed at the surface. In the literature, the C_dl is estimated using values obtained using metal electrode experiments. Due to the distinctive electronic and surface properties of graphene, there is reason to believe these estimates are inadequate. This work seeks to directly characterize the double layer capacitance of a GFET. A unique method for determining the C_dl has been implemented, and data has been obtained for three electrolytes and one ionic fluid. The results yield dramatically lower C_dl values than …

Investigation Of Microfluidic Kelvin Water Dropper And Its Applications In Contact And Contactless Electrowetting, Elias Yazdanshenas

Mechanical & Aerospace Engineering Theses & Dissertations

A typical Kelvin water dropper is a device that can convert gravitational potential energy to a high voltage electrostatic. This device consists of two inductors, two collectors, tubes, and electrical connections. A Kelvin water dropper is able to generate extremely high voltage by separating ions using two positive feedback loops. A Kelvin water dropper provides a low cost solution for the applications in which high voltage is needed. In the present research, low cost Microfluidic Kelvin Water Droppers (MKWDs) were developed and built in house for electrowetting applications. Two MKWDs with different tube inner diameters (254 and 508 μm) were …

Communication Based Control For Dc Microgrids, Mahmoud S. Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

Centralized communication-based control is one of the main methods that can be implemented to achieve autonomous advanced energy management capabilities in DC microgrids. However, its major limitation is the fact that communication bandwidth and computation resources are limited in practical applications. This can be often improved by avoiding redundant communications and complex computations. In this paper, an autonomous communication-based hybrid state/event driven control scheme is proposed. This control scheme is hierarchical and heuristic, such that on the primary control level, it encompasses state-driven local controllers, and on the secondary control level, an event-driven MG centralized controller (MGCC) is used. This …

Optimal Operation Of Integrated Microgrids, Abdullah Albaker

Electronic Theses and Dissertations

Microgrids' deployments are increasing and projected to increase even more in future due to the significant advantages that are provided by this technology for end-use customers. However, microgrids can be connected to each other to create integrated microgrids system, which can further promote the anticipated and desired benefits. An integrated operation of microgrids can potentially improve the local power system reliability and resilience, increase the individual microgrids' economic benefits, and promote further utilization of renewable energy resources. Integrating microgrids, to achieve a microgrid network or cluster, is expected be an essential application towards smarter power grids and a key operational …

Predicting Energy And Water Consumption On Dairy Farms Through Statistical Analysis And Machine-Learning Methods, Philip Shine

Theses

With the abolishment of milking quotas across all European Union member states in April 2015, dairy farmers must adjust their farming practises to minimise milk production costs to adequately prepare for potential periods of reduced revenue. Milk production is an intense energy and water consuming process. Coupled with challenging European greenhouse gas reduction targets and legislation regarding the prevention of groundwater pollution and deterioration, increasing the production of milk in Ireland must be met with the sustainable consumption of on-farm energy and direct water resources, to ensure the future monetary and environmental sustainability of Ireland’s dairy industry. Thus, this body …

Nonlinear Stochastic Filtering For Online State Of Charge And Remaining Useful Life Estimation Of Lithium-Ion Battery, Suresh Daravath

Electronic Theses and Dissertations

Battery state monitoring is one of the key techniques in Battery Management System (BMS). Accurate estimation can help to improve the system performance and to prolong the battery lifetime. The main challenges for the state online estimation of Li-ion batteries are the flat characteristic of open circuit voltage (OCV) with the function of the state of charge. Hence, the focus of this thesis study is to estimation of the state of charge (SOC) of Li-ion with high accuracy, more robustness. A 2nd order RC equivalent circuit model is adapted to battery model for simulation, mathematical model analysis, and dynamics characteristic …

Hosting Capacity Optimization In Modern Distribution Grids, Mansoor T. Alturki

Electronic Theses and Dissertations

The availability of distributed renewable energy resources and the anticipated increase in new types of loads are changing the way electricity is being produced and supplied to consumers. This shift is moving away from a network delivering power solely from centralized power plants towards a decentralized network which supplements its power production by incorporating local distributed generators (DGs). However, the increased integration of DGs into existing distribution networks is impacting their behavior in terms of voltage profile, reliability, and power quality. To determine the maximum amount of DG that distribution grids can accommodate the concept of hosting capacity is introduced. …

Automated Cfd Optimization To Maximize Wind Farms Performance And Land Use, Rafael Valotta Rodrigues

Electronic Theses and Dissertations

In this research, a computational system was designed to analyze and optimize the layout of wind farms under variable operational conditions. At first, a wind turbine computational fluid dynamic (CFD) model was developed covering the near wake. The near wake flow field was validated against near wake velocity data from the MEXICO experiment. The CFD simulation demonstrated that the tip speed ratio and the pitch angle greatly influence the near wake behavior, affecting the velocity deficit and the turbulence intensity profile in this region. The CFD model was extended to cover the far wake, aiming to become a computational tool …

Electrowetting Using A Microfluidic Kelvin Water Dropper, Elias Yazdanshenas, Qiang Tang, Xiaoyu Zhang

Mechanical & Aerospace Engineering Faculty Publications

The Kelvin water dropper is an electrostatic generator that can generate high voltage electricity through water dripping. A conventional Kelvin water dropper converts the gravitational potential energy of water into electricity. Due to its low current output, Kelvin water droppers can only be used in limited cases that demand high voltage. In the present study, microfluidic Kelvin water droppers (MKWDs) were built in house to demonstrate a low-cost but accurately controlled miniature device for high voltage generation. The performance of the MKWDs was characterized using different channel diameters and flow rates. The best performed MKWD was then used to conduct …

Ball Oscillating Bouncer, Eric Blok, Daniel Altemese, Ryan Nowacki, Maram Qurban

Williams Honors College, Honors Research Projects

The purpose of this report is to document the need, objectives, marketing and engineering requirements, as well as validate the design of an autonomous control device capable of continuously bouncing a table tennis ball on a paddle. This includes the design of a self correcting system using lightweight materials, and as few sensors and components as possible to achieve a compact, portable design. To accomplish this, the system is designed to react to a ball falling from as short a distance as 10 centimeters above the paddle, meaning all sensor processing, control processing, and motor drives should be able to …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

Co-Simulation Framework For Power Distribution System Analysis With Humans In The Loop, Victor H. Ayon

Mechanical Engineering ETDs

Recent developments in the area of power generation have led to an increased penetration of storage and distributed energy resources (DER) in power distribution systems. As a result, new and enhanced energy management systems will be necessary as the deployment of DERs, as well as the need to control loads, continues to increase in the coming years. Advanced management systems are especially important to achieve resilient power delivery during emergency situations. During a blackout for example, a section of a distribution feeder could island to operate as a microgrid to ensure critical services such as water, food, and medical care …

Conjugated Dynamic Modeling On Vanadium Redox Flow Battery With Non-Constant Variance For Renewable Power Plant Applications, Abu Nayem Md. Asraf Siddiquee

Student Theses and Dissertations

A parametric modeling study has been carried out to assess the impact of change in operating parameters on the performance of Vanadium Redox Flow Battery (VRFB). The objective of this research is to develop a computer program to predict the dynamic behavior of VRFB combining fluid mechanics, reaction kinetics, and electric circuit. The computer program was developed using Maple 2015 and calculations were made at different operating parameters. Modeling results show that the discharging time increases from 2.2 hours to 6.7 hours when the concentration of V2+ in electrolytes increases from 1M to 3M. The operation time during the charging …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …