Electrical and Electronics Commons^™

Measurement Of Speed Of Sound Profile Using Laaces Balloon, Zhuang Li, Brett Schaefer, Brian Schaefer, William Dever, Tyler Morgan, Matthew Foltz

2017 Academic High Altitude Conference

The goal of this mission is to test the speed of sound at different altitudes and ultimately at a maximum height of 100,000 feet (30 km). In conjunction with this testing, environmental parameters including temperature, pressure, and humidity are measured and used to calculate the speed of sound to compare to the measured results. The team constructed the payload “Dorothy” using polystyrene foam due to its lightweight and thermal isolation property. An ultrasonic sensor with a reflection mirror were installed outside payload box to measure speed of sound. All the sensors were calibrated. Software for the project was developed in …

Multiple Camera Control Using An Octaplexer In A 5.8 Ghz Video System, Uciel Garcia Olmedo, Skylar Tamke

2017 Academic High Altitude Conference

One of the greatest challenges with camera systems on High-Altitude Balloons (HAB) is to control the direction that they point. This is because the payload boxes constantly rotate during the flight. While mechanical gambles are normally used, an electronic gambled was designed using multiple cameras and a series of multiplexers. The design consists of 8 version 1 pi cameras, connected through a series of multiplexers and interfacing with an IMU to tell the direction the cameras are facing. This design attaches to the Raspberry Pi through the GPIO pins. The multiplexers turn on the camera facing the orientation desired and …

Placing A High-Altitude Balloon In The Path Of Totality, Nicholas Jordan, Christopher Helmerich

2017 Academic High Altitude Conference

The UAH Space Hardware Club had conducted 70 flights prior to the Eclipse. In this time, we have gained valuable skills and experience which we have put into practice and passed on through the years. We put these skills into practice for the Eclipse. Our first challenge was finding where to launch. We started out by looking for suitable locations inside totality. We also examined a map of totality at 80,000 ft. We then ran predictions based on past weather during that time of year. By compiling multiple past predictions, we eliminated possible launch sites. We had multiple payloads, some …

New Approach To Improve The Breakdown Strength For Thick Dielectrics: A Theoretical Study, Sijay Huang, Biswajit Ray

Von Braun Symposium Student Posters

No abstract provided.

Characterization Of A Microplasma-Based Heaterless, Insertless Cathode, Ryan Gott, Gabriel Xu

Von Braun Symposium Student Posters

No abstract provided.

Answering Food Insecurity: Serving The Community With Food And Knowledge Using Technology, Courtney Simpson

Purdue Journal of Service-Learning and International Engagement

The courses of Tech120, CGT110, and ENGT 180/181 and Red Gold at Purdue collaborated to design a robot that would plant and water a garden for a local community charter school. The students centered the project on the users’ needs for fresh food, nutrition education, and early exposure to STEM for children. The school, Anderson Preparatory Academy (APA), is comprised of many children who come from low-income families and are in the free or reduced lunch program. Inspired from “Farm Bot,” a similar system that allows for almost hands-free gardening, the “Boiler Bot” is designed to be scalable so children …

A Novel E-Voting System With Diverse Security Features, Haijun Pan

Dissertations

Internet-based E-voting systems can offer great benefits over traditional voting machines in areas, such as protecting voter and candidate privacy, providing accurate vote counting, preventing voter fraud, and shortening the time of vote counting. This dissertation introduces, establishes and improves Internet-based E-voting systems on various aspects of the voting procedure. In addition, our designs also enable voters to track their votes which is a very important element in any elections.

Our novel Internet-based E-voting system is based on the following realistic assumptions: (1) The election authorities are not 100% trustworthy; (2) The E-voting system itself is not 100% trustworthy; (3) …

Machine Learning Based Digital Image Forensics And Steganalysis, Guanshuo Xu

Dissertations

The security and trustworthiness of digital images have become crucial issues due to the simplicity of malicious processing. Therefore, the research on image steganalysis (determining if a given image has secret information hidden inside) and image forensics (determining the origin and authenticity of a given image and revealing the processing history the image has gone through) has become crucial to the digital society.

In this dissertation, the steganalysis and forensics of digital images are treated as pattern classification problems so as to make advanced machine learning (ML) methods applicable. Three topics are covered: (1) architectural design of convolutional neural networks …

Silicon-Germanium Nanowire Heterojunctions: Optical And Electrical Properties, Xiaolu Wang

Dissertations

Semiconductor nanowires are quasi-one-dimensional objects with unique physical properties and strong potential in nanophotonics, nanoelectronics, biosensing, and solar cell devices. The next challenge in the development of nanowire functional structures is the nanowire axial heterojunctions, especially lattice mismatched heterojunctions. Si and Ge have a considerable lattice mismatch of ~ 4.2% as well as a mismatch in the coefficient of thermal expansion, and the formation of a Si_1-xGe_x transition layer at the heterointerface creates a non-uniform strain and modifies the band structures of the adjacent Si and Ge nanowire segments. These nanostructures are produced by catalytic chemical …

Simulation, Performance And Interference Analysis Of Multi-User Visible Light Communication Systems, Adel Aldalbahi

Dissertations

The emergence of new physical media such as optical wireless, and the ability to aggregate these new media with legacy networks motivate the study of heterogeneous network performance, especially with respect to the design of protocols to best exploit the characteristics of each medium.

This study considers Visible Light Communications (VLC), which is expected to coexist with legacy and future radio frequency (RF) media. While most of the research on VLC has been done on optimizing the physical medium, research on higher network layers is only beginning to gain attention, requiring new analyses and tools for performance analysis.

The first …

Quantitative Analysis Of Regenerative Energy In Electric Rail Traction Systems, Mahmoud Saleh, Oindrilla Dutta, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper aims at determining the influential factors affecting regenerative braking energy in DC rail transit systems. This has been achieved by quantitatively evaluating the dependence of regenerative energy on various parameters, such as vehicle dynamics, train scheduling, ground inclination and efficiency of the electrical devices. The recuperated power and energy have been presented by a mathematical model, comprising of a set of empirical forms, which allows for thorough analysis. A detailed simulation model of a typical DC-traction system has been developed to validate the developed empirical forms. The results verified the validity of the proposed mathematical model, and demonstrated …

Optimal Microgrids Placement In Electric Distribution Systems Using Complex Network Framework, Mahmoud Saleh, Yusef Esa, Nwabueze Onuorah, Ahmed Mohamed

Publications and Research

This paper provides a new approach to find the optimal location for Microgrids (MGs) in electric distribution systems using complex network analysis. An optimal location in this paper refers to a location that would result in increased grid resilience, reduced power losses, less line loading, higher voltage stability and secured supply to critical loads during power outage. The criteria used to find the optimal placement of MGs were based on the centrality analysis adopted from complex network theory, the center of mass concept used in physics, and the controlled delivery grid (CDG) concept. An IEEE 30-bus system was used as …

Event And Time-Triggered Control Module Layers For Individual Robot Control Architectures Of Unmanned Agricultural Ground Vehicles, Tyler Troyer

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Automation in the agriculture sector has increased to an extent where the accompanying methods for unmanned field management are becoming more economically viable. This manifests in the industry’s recent presentation of conceptual cab-less machines that perform all field operations under the high-level task control of a single remote operator. A dramatic change in the overall workflow for field tasks that historically assumed the presence of a human in the immediate vicinity of the work is predicted. This shift in the entire approach to farm machinery work provides producers increased control and productivity over high-level tasks and less distraction from operating …

A Correlational Study Of Sansec Sensors’ Electric Field Distribution On Lightning Attachment, Kayla M. Farrow

Electrical & Computer Engineering Theses & Dissertations

Old Dominion University and the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) Aviation Safety Program Atmospheric Environmental Safety Technologies Project team conducted research in using SansEC (Sans Electric Connection) sensors to provide lightning strike protection (LSP) and damage mitigation for composite aircraft. SansEC sensors are simplistic devices consisting of an open circuit conductive trace, shaped in a planar geometric spiral [1], [2], [3]. SansEC sensors can be designed in various shapes and sizes depending on the application. For applications on exterior aircraft surfaces, the sensor must be designed to perform the required lightning strike protection [1], [3]. …

Energy Management Algorithm For Resilient Controlled Delivery Grids, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed, Haim Grebel, Roberto Rojas-Cessa

Publications and Research

Resilience of the power grid is most challenged at power blackouts since the issues that led to it may not be fully resolved by the time the power is back. In this paper, a Real-Time Energy Management Algorithm (RTEMA) has been developed to increase the resilience of power systems based on the controlled delivery grid (CDG) concept. In a CDG, loads communicate with a central controller, periodically sending requests for power. The central controller runs an algorithm, based on which it may decide whether to grant the requested energy fully or partially. Therefore, the CDG limits loads discretionary access to …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

Engineered Surfaces To Control Secondary Electron Yield For Multipactor Suppression, James M. Sattler

Theses and Dissertations

A significant problem for satellites, vacuum electron devices, and particle accelerators is multipactor: an avalanche of electrons caused by recurring secondary electron emission (SEE) in a time-varying electric field. The consequences of multipactor range from temporary to permanent device failure. This research studied how surface topography can be engineered to minimize SEE and suppress multipactor. Two new semi-empirical models (one based on a 2D pore, the other based on a 3D pore) were developed to predict the secondary electron yield (SEY) of a porous surface based on pore aspect ratio and porosity. The models were validated with experimental SEY measurements …

On Dual-Band Amplifications Using Dual Two-Tones: Clarifications And Discussion, Siyuan Yan, Xianzhen Yang, Xiao Li, Fu Lo

Electrical and Computer Engineering Faculty Publications and Presentations

A significant development of recent research in nonlinear distortion is the expansion of the conventional two-tone test for power amplifiers to the concurrent dual-band transmitters, by Amin et al. A general framework using dual two-tones is developed, which shows that the output signal is affected not only by intermodulation (IM) products but also by cross-modulation (CM) products. In this paper, we will make a number of clarifications to Amin et al.'s paper. The effects of IM and CM in passband will be discussed, IM represents a reduction for compressive devices, and CM reflects an interference caused by the signal from …

Design And Validation Of A Low Cost High Speed Atomic Force Microscope, Michael Ganzer, Tien Pham

Journal of Undergraduate Research at Minnesota State University, Mankato

The Atomic Force Microscope (AFM) is an important instrument in nanoscale topography, but it is expensive and slow. The authors designed an AFM to overcome both limitations. To do this, they used an Optical Pickup Unit (OPU) from a DVD player as the laser and photodetector system to minimize cost and they did not implement a vertical control loop, which maximized potential speed. Students will be able to be use this device to make nanoscale measurements and engage in micro-engineering. To prototype this idea, the authors tested an OPU with a silicon wafer and demonstrated the ability to consistently distinguish …

Solar Powered Single-Axis Heliostat Active Solar Tracking Device, Mason Kyle Roberts

Physics

As a means of cooking food, the burning of biomass accounts for over 4 million premature deaths in third world countries (“Household Air Pollution and Health”). The focus of this project was to explore an alternative that could utilize focused sunlight to cook food. A solar tracker was designed to be affixed to a parabolic, reflective, tilted single axis heliostat to follow the sun throughout the day and focus the reflected light to the bottom of a cooking surface. This surface became hot enough to for the preparation of food or boiling/sterilization of water.

A goal for each project was …

Iterative Learning Control For Improved Tracking Of Fluid Percussion Injury Device, Steve Susanibar

Theses

Traumatic brain injury (TBI) afflicts over 10 million people around the world. Injury to the brain can occur from a variety of physical insults and the degree of disability can greatly vary from person to person. It is likely that the wide range of TBI outcomes may be due to the magnitude, direction, and forces of biomechanical insult acting on the head during such TBI events. Lateral Fluid Percussion (FPI) brain injury is one of the most commonly used and well-characterized experimental models of TBI. A Fluid Percussion Injury (FPI) device in the laboratory is used to replicate the injury …

Parallel Computation Using Mems Oscillator-Based Computing System, Xinrui Wang, Ilias Bilionis, Salar Safarkhani

The Summer Undergraduate Research Fellowship (SURF) Symposium

In recent years, parallel computing systems such as artificial neural networks (ANNs) have been of great interest. In these systems which emulate the behavior of human brains, the processing is carried out simultaneously. However, it is still a challenging engineering problem to design highly efficient hardware for parallel computing systems. We will study the properties of networks of Microelectromechanical System (MEMS) oscillators to explore their capabilities as parallel computing infrastructure. Furthermore, we simulate the time-variant states of MEMS oscillators network under various initial conditions and performance of certain tasks. Recent theoretical results show that networks of MEMS oscillators have some …

Novel Pet Systems And Image Reconstruction With Actively Controlled Geometry, Ke Li

McKelvey School of Engineering Graduate Student Theses & Dissertations

Positron Emission Tomography (PET) provides in vivo measurement of imaging ligands that are labeled with positron emitting radionuclide. Since its invention, most PET scanners have been designed to have a group of gamma ray detectors arranged in a ring geometry, accommodating the whole patient body. Virtual Pinhole PET incorporates higher resolution detectors being placed close to the Region-of-Interest (ROI) within the imaging Field-of-View (FOV) of the whole-body scanner, providing better image resolution and contrast recover. To further adapt this technology to a wider range of diseases, we proposed a second generation of virtual pinhole PET using actively controlled high resolution …

Numerical Methods For Nonlinear Optimal Control Problems And Their Applications In Indoor Climate Control, Runxin He

McKelvey School of Engineering Graduate Student Theses & Dissertations

Efficiency, comfort, and convenience are three major aspects in the design of control systems for residential Heating, Ventilation, and Air Conditioning (HVAC) units. In this dissertation, we study optimization-based algorithms for HVAC control that minimizes energy consumption while maintaining a desired temperature, or even human comfort in a room. Our algorithm uses a Computer Fluid Dynamics (CFD) model, mathematically formulated using Partial Differential Equations (PDEs), to describe the interactions between temperature, pressure, and air flow. Our model allows us to naturally formulate problems such as controlling the temperature of a small region of interest within a room, or to control …

Design A Continuously Tunable Microwave Filter With A Generalized Constant And Frequency Mapping Technique, Josh Shao, Runqi Zhang, Dimitrios Peroulis

The Summer Undergraduate Research Fellowship (SURF) Symposium

As the demand for agile and accurate communication increases, the fundamental of communication must be improved to support the needs. Current communication operates on an agreement, that each network company pays government to get licensed a range of frequency on the spectrum, and no others are legally allowed to use. This allows a limited number of users to operates at the same time. As the number of users increase, the spectrum become congested and user experience problem like dropping call. This problem can be solved, if users can be shifted between different licensed frequencies, depending on the capacity of the …

Spectroscopic Contrast Of Diarylethene Molecules On Octanethiol Monolayer, Arramel Arramel, Tibor Kudernac, Nathalie Katsonis, Bernard Lucas Feringa, Bart Jan Van Wees

Makara Journal of Technology

We present a systematic scanning tunneling microscopy (STM) study of bias-dependent imaging of disulfur diarylethene (2S-DE) molecules on octanethiol (C8) monolayer at room temperature. In a rigid confinement of the C8 matrix, we did not observe any significant variation in the appearance of the 2S-DE. On the contrary, a reversal in the apparent height of the 2S-DE was present when the molecule was situated on a gold vacancy island. We attributed this finding to the presence of a new electronic state that became accessible for a tunneling event. In addition, the C8 surface structure underwent a reversible phase transformation from …

Residual Stress Measurements On The Tig Weld Joint Of 57fe15cr25ni Austenitic Steel For Structural Material Applications By Means X-Ray Diffraction Techniques, Parikin Parikin, Agus Hadi Ismoyo, Riza Iskandar, Arbi Dimyati

Makara Journal of Technology

Measurements of residual stress on the 57Fe25Cr15Ni steel plate with no-filler TIG-welding process were carried out. This work was conducted to determine the nature of weld ability in synthesized steel. The bulks were formed in a dimension of 30x20x7 mm3 to ease data retrieval. Results show that the largest residual stress occurred in the weld metal area, amounting to 82.40 MPa with lattice stretching of 0.18%. Conversely, the values decreased to 65.92 MPa and a stretch of 0.14% in the HAZ area. This residual stress is a tensile stress that can reduce the mechanical strength of the material since it …

An Efficient Palladium-Thiourea Catalysed Heck Cross-Coupling Reaction For Molecular Electronic Interest, Wan M. Khairul, Mohd Shahrul Shahmi Md Shariff, Rafizah Rahamathullah, Adibah Izzati Daud, Mustaffa Shamsuddin, Siti Kamilah Che Soh

Makara Journal of Technology

The synthesis and utilization of C-C bonds formation are concerned about the key steps for the building of several conducting molecular electronics involving many asymmetric catalysts approached, which is an essential task that most researchers would ignore in preparing these materials to enhance the production yield of cross-coupling materials. Despite the enormous progress, there still remains a great demand for economic and practicable cross-coupling processes involving ultra-low catalyst loadings with high turnover numbers due to the employment of conventional metal catalyst. Thus, there has been an excessive interest to cultivate non-phosphine palladium catalysts for excellent achievement of activity, stability, and …

A Study On Dielectric Properties Of The Cellulose Derivative-Nh4br-Glycerol- Based The Solid Polymer Electrolyte System, Nur Muhitul Jalilah Rasali, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin

Makara Journal of Technology

The characterization of biopolymer-based solid polymer electrolytes (SPEs) has been carried out in this present work. Cellulose derivative was chosen due to its superior physical attributes. In this work, NH4Br-doped glycerol plasticized carboxyl methylcellulose-based SPEs were successfully prepared via the solution casting method. The conductivity and dielectric properties of the prepared films were investigated using the impedance analysis which presented ~1.91×10-3 Scm-1 (with addition of 6 wt% of glycerol). In addition, the studied SPE system shows a non-Debye behaviour without a single relaxation time. The findings of the research indicate that the complexes of NH4Br and glycerol in the cellulose …

Urban Drainage Management And Flood Control Improvement Using The Duflow Case Study: Aur Sub Catchment, Palembang, South Sumatra, Indonesia, Charlotte De Fraiture, Robiyanto Hendro Susanto, F.X. Suryadi, Harrini Mutiara Hapsari Wahyu

Makara Journal of Technology

Urban flooding often times staggers the livelihood in an urban area, which most likely happens in the lowland urban area. Therefore, the existing urban drainage system should be improved in order to tackle the upcoming urban flooding events, which are more than likely to be more devastating than those in the previous years. The research location is in Palembang, Sumatra, Indonesia, where 30% of its urban part is a lowland area. The selected Aur Sub Catchment is located in Silaberanti. The main objective of this research is to improve the current drainage system in order to achieve the optimal design …