Electrical and Electronics Commons^™

Influences Of Cardiac And Respiratory Parameters On Heart Rate Variability, Melissa Leifer

Theses

Heart rate variability is a result of variation in the activity of the sympathetic and parasympathetic nervous systems. Methods have been developed to determine the level of parasympathetic activity by observing the heart rate variability spectrum. Most of the previously published research uses only level of parasympathetic activity and respiratory rate to draw conclusions about the interactions of the autonomic nervous system with physiological parameters. In order to gain a complete understanding of the autonomic nervous system and the mechanisms responsible for heart rate variability, respiratory volume, cardiac variables and pulmonary variables need to be considered. In addition, amount of …

Adaptive Receivers For Direct-Spread And Multi-Carrier Code Division Multiple Access Systems, Xiangqun Liu

Theses

In this thesis, the detection of Direct Sequence Code Division Multiple Access (DS-CDMA) signals in an AWGN channel and Multi-Carrier (MC) CDMA signals in a time-dispersion channel is discussed.

The DS-CDMA receiver employs an adaptive multiuser interference canceler that utilizes deadzone limiters in the tentative decision stage. With weights adjusted adaptively, the prior knowledge of signal powers is unnecessary. The steady state error performance of this receiver is obtained and found to be superior to the performance of the same receiver using hard limiters for tentative decisions. The channel is considered non-fading in. this receiver.

Modeling the frequency selective channel …

Cebus Demonstration System, Liang-Chuang Chen

Theses

A CEBus demonstration system is constructed and applied to aspects of home automation security. Two M68HC16Z1 evaluation boards are used as CEBus nodes. Two CEBus spread spectrum power line modems (SSC PLCEMS) interconnect the nodes. An SSC PLCEMS handles all spread spectrum signal generation and reception.

The application programs in the two boards are written in assembly language based upon CAL (Common Application Language), a CEBus standard.

The standard CEBus frame format and FCS (Frame Check Sequence) are implemented by software in the Data Link Layer. Encoding and decoding binary information into UST format are implemented in the Physical Layer. …

A Distributed Network Architecture For Video-On-Demand, Ge Dai

Theses

The objective of this thesis is to design a distributed network architecture that provides video - on - demand services to public subscribers. This architecture is proposed as an alternative to a centralized video service system. The latter system is currently being developed by Oracle Corporation and NCube Corporation.

A simulator is developed to compare the performance of both the distributed and centralized video server architectures. Moreover, an estimate of the cost of both systems is derived using current price data.

It is shown that the distributed video server architecture offers a better cost / performance trade-off than the centralized …

Decentralized Optimal Control In Descriptor Systems, Hag-Yeon Park

Theses

Application of Matrix Minimum Principle to a linear decentralized optimal control in descriptor systems is studied in this thesis. Linear-quadratic index of performance with Gaussian initial state is considered. The necessary and sufficient conditions for optimality are derived

An additional constraint is imposed such that the controllers are linear function of output y(t) rather than of the state vector x(t). The optimal gain matrix G_i^* is then specified by the necessary conditions.

Two examples are developed to illustrate the concept.

Processor Allocation For Partitionable Multiprocessor Systems, Nicholaos C. Antoniou

Theses

The processor allocation problem in an n-dimensional hypercube multipro-cessor is similar to the conventional memory allocation problem. The main objective is to maximize the utilization of available resources as well as minimize the inherent system fragmentation. In this thesis, a new processor allocation strategy is proposed, and compared with the existing strategies, such as, the Buddy strategy, the Single Gray Code strategy (SGC), the Multiple Gray Code (MGC), and the Maximal Set of Subcubes (MSS). We will show that our proposed processor allocation strategy outperforms the existing strategies, by having the advantage of being able to allocate unused processors to …

An Adaptive Correlator Receiver For Combined Suppression Of Co-Channel Interference And Narrow-Band Jammers In A Slowly Fading Channel, Raymond Carbone

Theses

This work deals with the adaptive correlation of a direct sequence spread spectrum signal in the presence of narrow-band, multipath and multiple user interference. The Least Mean Square and Recursive Least Square algorithms are employed for the adaptive convergence of the correlator receiver to minimize the mean squared error.

The performance of the adaptive correlator is compared with the matched filter correlator receiver and the conventional prediction filter for the suppression of narrow-band interference by calculating the bit error probability rate. The adaptive correlator is also compared with the RAKE receiver for multipath suppression and compared to the decorelating detector …

Passive Radiosonde Transducer Design For Remote Pressure Sensing Applications, Yang Gao

Theses

Intracranial pressure can be measured to accuracies within 1 milliTorr using passive microtransponders that are micromachined using silicon as a base technology. These microtransponders can operate with either a dual-oscillator or a phase-locked loop frequency scanned control system.

The current work describes the design of a totally implantable microsensor for biomedical applications with the aim to monitor and measure the epidural intracranial pressure . The implanting microsensor is basically an RLC device in which capacitance varies with fluid pressure. The resonant frequency of RLC Series connected device varies with chemically etched diaphragm electrode spacing and thereby measures the variations with …

Cad Study Of Linear Tapered Slot Antenna, Anthony W. Kwan

Theses

Linear Tapered Slot Antenna (LTSA) is an attractive candidate as a radiating element in frequency scanning arrays. LTSA element backed by a rectangular cavity had been investigated and is proven to posses various physical design parameters suitable to optimize its performance. This study is focused on the feed position variation to optimize the performance while maximum of the current density variation is maintained in the slot region. It was observed that if the stub base of the microstrip feed structure is located in the middle of the slot region, current maximum can be obtained within the slot region at the …

Data Broadcasting And Reduction, Prefix Computation, And Sorting On Reduced Hypercube (Rh) Parallel Computers, Arup Mukherjee

Theses

The binary hypercube parallel computer has been very popular due to its rich interconnection structure and small average internode distance which allow the efficient embedding of frequently used topologies. Communication patterns of many parallel algorithms also match the hypercube topology. The hypercube has high VLSI complexity. however. due to the logarithmic increase in the number of connections to each node with the increase in the number of dimensions of the hypercube. The reduced hypercube (RH) interconnection network. which is obtained by a uniform reduction in the number of links for each hypercube node. yields lower-complexity interconnection networks when compared to …

Artificial Dielectrics : Characteristics At Low And Microwave Frequencies, Nitish Agrawal

Theses

Artificial Dielectrics have been characterized using transmission line and s- parameter measurements. The complex dielectric constant and loss of graphite filled and non-poled piezoelectric-aggregate (Polyvinylidene Fluoride, PVDF) filled plastic (PMMA) has been characterized at low (1kHz-10kHz range, i.e., the VLF, very low frequency, range) and microwave frequencies. The average diameter diameter of graphite particles used was thirty microns. Measurements were performed on very fine graphite (one micron diameter grains) and 30 micron sized grains for comparison purposes. Fine grain graphite particles exhibited a, larger real dielectric constant, probably owing to a larger dipole effect. The dielectric constant characterization has also …

Control Of Smart Structure Using Adaptive Dither, Tian Hong

Theses

In this thesis, a mathematical model of a piezoelectric stack actuator is presented to describe its voltage versus displacement hysteresis characteristices. This model can accommodate a wide range of piezoelectric materials, including the PZT (lead zirconate-lead titanate) type which is most popular in industrial applications.

Besides describing the conventional "single-loop" hysteresis, this model also accounts for the off-axis minor loops by augmenting the algorithm with loop indexing.

It is shown that the PZT hysteresis possesses certain "weak scalability" that enables the use of spectral analysis to measure the level of nonlinearity.

After a suitable mathematical model has been obtained, a …

Low Cost Schottky Barrier Solar Cells Fabricated On Cdse And Sb2S3 Films Chemically Deposited With Silicotungstic Acid, O. Savadogo, K. C. Mandal

Faculty Publications

No abstract provided.

Polarized Light Reflectometer, R. M.A. Azzam

Electrical Engineering Faculty Publications

The modulated reflected and nonreflected light fluxes, measured as the azimuth of incident linearly polarized light is varied, yield the absolute reflectances R_p, and R_s, of a dielectric or semiconductor surface. Application to a reflective Si detector determines the refractive index and thickness of a SiO₂ film on the detector surface.

An Appraisal Of Electricity Supply In Nigeria And The Privatisation Option, E. I. K. Sule, C. M. Anyanwu

CBN Occasional Papers

Incessant electric power cuts in most parts of the country has become a normal feature of electricity supply throughout Nigeria. The power outages cause much inconvenience and economic losses to all and sundry. This study has shown that the most critical factor behind the incessant power failure is the problem of inadequate funding of the industry at a time it was forced to accommodate rapid expansion. Other factors include lack of autonomy, inefficiency, poor organization as well as lack of skilled manpower. The paper has examined these problems on the basis of which suggestions are made on how the worrisome …

Transient Simulations And Modelling Of Semi-Insulating Gaas Photoconductive Switches, Prasun Kumar Raha

Electrical & Computer Engineering Theses & Dissertations

The primary objective of this thesis is to develop a one-dimensional transient simulator for Photoconductive Semiconductor Switches (PCSS) taking into consideration the material characteristics, the internal physical effects, and the external circuit. Simulations have been performed to study the device behavior at different voltage levels for copper-doped silicon-compensated GaAs material, though other materials could easily be simulated by changing the parameters. The model includes hole transport, and the results demonstrate the effect of hole injection, with and without recombination centers. In addition to developing a one-dimensional transient simulator, the role of various physical effects, such as the field-dependence of trapping …

Direct Relation Between Fresnel's Interface Reflection Coefficients For The Parallel And Perpendicular Polarizations: Erratum 2, R. M.A. Azzam

Electrical Engineering Faculty Publications

The record is set straight concerning two equations that determine the reflection phase shifts at a single interface from the intensity reflectances forp- and s-polarized light at one angle of incidence. These equations appeared previously in this journal [J. Opt. Soc. Am. 69, 1007 (1979); erratum, J. Opt. Soc. Am. 70, 261 (1980)].

Dual Versus Single Spark Plug: A Critique, I Mshoro

Tanzania Journal of Engineering and Technology (TJET)

Dual spark plugs are occasionally employed on certain modern Spark lg- nited (S') engines, viz lean burn engines. Their benefit has generally been noticed in the operating conditions whenfuel-air mixture is very lean, or when a larger proportion of EGR has been employed, or during the part load conditions and so on. An extensive literature survey has indi- cared an interesting spectrum of reasons for gains due to the dual spark plug. A consistent explanation is found to be missing which can describe the behaviour of the engines with single versus dual spark plugs There are quite "few researchers who …

An Alternative Method Of Interfacing A Dc Motor To A Microprocessor For Mo- Tion Control, M Selekwa

Tanzania Journal of Engineering and Technology (TJET)

A Simple and cheap alternative method Of interfacing a permanent mag- net dc motor to a motion control using switch- ing transistor motor drivers is presented. This method involves the use Of very few transistor-transistor logic (TTL) devices and a 555 timer to pro- duce a pulse width modulated (P WM) signal which is required by the mo- ror driver. The motor driver in this case should be of an H-bridge type. Like other methods currently in use, it relieves the MPU of all timing func- tions which are necessary in the generation of P WM signals. The present method, …

Motion Estimation Using Optical Flow Field, Jingning Pan

Dissertations

Over the last decade, many low-level vision algorithms have been devised for extracting depth from intensity images. Most of them are based on motion of the rigid observer. Translation and rotation are constants with respect to space coordinates. When multi-objects move and/or the objects change shape, the algorithms cannot be used.

In this dissertation, we develop a new robust framework for the determination of dense 3-D position and motion fields from a stereo image sequence. The framework is based on unified optical flow field (UOFF). In the UOFF approach, a four frame mode is used to compute six dense 3-D …

Estimation And Cancellation Of Friction In Control Systems, Sofia Mentzelopoulou

Dissertations

The research reported in this dissertation concerns the estimation and cancellation of friction in control systems. For purposes of analysis, the Coulomb friction model, the "extended" Coulomb friction model as well as dynamic friction models are used. In addition, for systems with multiple degrees-of-freedom, a general matrix representation of friction is presented.

For the design of the friction estimators, the theory of nonlinear observers is applied. In particular, for a system with multiple degrees-of-freedom, holonomic constraints, and multiple friction sources, three different observers are presented to estimate the friction force or torque. The first (Generalized Coulomb Friction Observer) is designed …

Investigation Of Paraelectric Ptl Thin Films Using Reactive Magnetron Sputtering, Hyun Hoo Kim

Dissertations

The study of methods to prepare paraelectric perovskite PLT (Pb_1-xLa_xTi_1-x/4O₃; x=0.28) thin films has been important because thin films of this high dielectric strength material are required to make high density capacitors for dynamic random access memory. In this research, paraelectric PLT thin films were prepared on multi-layer (Pt/Ti/SiO₂/Si) and MgO substrates in a unique way by the reactive magnetron sputtering method using a multi-component metal target. The individual control of each metal area on the sputtering target had considerable influence on the stoichiometry and electrical properties of the thin …

Heart Rate Variability Study Using Phase Response Curve, Peizhuan Zhang

Dissertations

A noninvasive phase resetting experiment on human subjects was investigated. The phase response curve was estimated and was used to demonstrate cardiac phase resetting due to a vagal input. The estimated running phase response curve showed that the cardiac cycle resetting depended on the time and the amplitude of the vagal stimulation. The phase response curve was then studied using time circle analysis, topological analysis and nonlinear dynamics analysis. Also phase entrainment and stimulus frequency dependence of the phase response were evaluated. Further, the Van Der Pol model, Generalized Additive model and Knight and Peskin's model were used to simulate …

Blind Detection In Channels With Intersymbol Interference, Raafat Edward Kamel

Dissertations

In high speed digital transmission over bandlimited channels, one of the principal impairments, besides additive white Gaussian noise, is intersymbol interference. For unknown channels, adaptive equalization is used to mitigate the interference. Different types of equalizers were proposed in the literature such as linear, decision feedback equalizers and maximum likelihood sequence estimation. The transmitter embeds sequences with the data regularly to help the equalizer adapt to the unknown channel parameters.

It is not always appropriate or feasible to send training sequences; in such cases, self adaptive or blind equalizers are used. The past ten years have witnessed an interest in …

A Novel Beam-Assisted Thickness Measurement Technique For Nanostructures, Luis Manual Casas

Theses

A novel method for measuring thickness of thin films has been developed. This method is straightforward, quickly accomplished, and offers resolution of device layers approaching that given by transmission electron microscopy. Ion beam bombardment of a multi-layer structure forms a crater in which the crater sidewalls are beveled at a very shallow angle, revealing various layers within the sample at a high degree of magnification. Beveled film thicknesses are measured by scanning Auger electron spectroscopy. Depth profilometry is used to measure the shallow beveling angle. Through knowledge of the beveled layer thickness and the bevel angle, actual film thicknesses are …

Simulation Analysis Of Fddi Network Using Network Ii.5 Software Package, Anastassis A. Lazarides

Theses

In recent years, one of the most exciting advances in media has been the use of fiber optics in LANs. The bandwidth provided by Fiber Optic Technology has drastically increased the number of new applications that can be supported by communication networks. In order to support a variety of services, in 1986, the American National Standard Institute (ANSI) Accredited Standards Committee (ASC) X3, and the ASC X3T9.5 Task Group developed a new standard; the Fiber Distributed Data Interface (FDDI) [1]. This is a high speed (100 Mbps) optical communication network based on a token passing mode of operation. The Medium …

Interference Cancellation By Time Adjustable Sampling, Josko Zec

Theses

The problem of improving the frequency response of linear arrays is addressed in this thesis. The improvement is measured in the level of rejection of the undesired sources. A new, simple, and practical method is suggested. It is based on adjusting the sampling time in selected channels. Interference cancellation for finite bandwidth signals is accomplished only at, or close to, the carrier frequency. Wideband cancellation requires additional hardware and computational complexity. Conventional way of the wideband interference cancellation utilizes tapped delay line adaptive filters in each channel.

The Time Adjustable Sampling (TAS) method achieves a part of the tapped delay …

Programmable Microstrip Dipole Antenna Design, Jing Zhu

Theses

The narrow bandwidth of microstrip dipole antennas is a major limitation for many applications. A method to increase the microstrip dipole antenna bandwidth is illustrated in this thesis. The proposed method utilizes micromechanical actuators to adjust the electrical length of the dipole antenna. The length change is realized by the activities of several microactuators arranged on both arms of the antenna. The radiation pattern and input impedance, as well as the microactuator mechanisms are detailed in this thesis. A programmable microstrip dipole antenna including the microactuators has been designed with the feedline taken into consideration. The fabrication techniques for this …

Motion Compensation Using Correlation-Feedback, Zebiba Shifa

Theses

Motion compensation is widely used for exploiting temporal redundancies in the coding of image sequences. Accurate estimation of motion information in image sequences is important in motion-compensated coding. Different approaches have been used to estimate motion to obtain the motion-compensated frame difference signal.

This work uses the correlation-feedback approach to estimate the velocity or the optic flow of the moving image pixel. After the motion of the pixel is estimated. the motion-compensated frame difference signal is found by subtracting the current. frame from the predicted frame.

This correlation-feedback approach estimates the true motion vector of moving image accurately. Consequently, the …

Narrow-Band Interference Rejection In Spread Spectrum Using An Eigen Analysis Based Approach, Aparna Vadhri

Theses

A new adaptive technique is suggested for rejecting narrow-band interferences in spread spectrum communications. When data is coded using a pseudo-noise code, the received signal consists of a wide-band signal with almost white spectral properties, thermal noise, and correlated narrow-band interferences. A new approach is proposed which exploits the statistical properties of the received signal via eigenanalysis of the received data. While the energy of the wide-band signal is distributed over all the eigenvalues of the signal autocorrelation matrix, the energy of the interference is concentrated in a few large eigenvalues. Hence, the eigenvectors corresponding to the large eigenvalues are …