Electrical and Electronics Commons^™

Contours Of Constant Pseudo-Brewster Angle In The Complex Є Plane And An Analytical Method For The Determination Of Optical Constants, R. M.A. Azzam, Ericson E. Ugbo

Electrical Engineering Faculty Publications

The locus of all points in the complex plane of the dielectric function є[є_r + jє_i = |є| exp(jθ)], that represent all possible interfaces characterized by the same pseudo-Brewster angle θ_pB of minimum p reflectance, is derived in the polar form: |є| = l cos(ζ/3), where l = 2(tan²Φ_pB)k, ζ = arccos(- cosθ cos²Φ_pB/k³), and k = (1 - 2/3 sin²Φ_pB)½. Families of iso-Φ_pB contours for (I) 0° ≤ Φ_pB ≤ …

Propagation Of Millimeter Wave Signals In Forests Using The Equation Of Radiative Transfer With Strong Forward Scattering Phase Functions, Nack Yang Cho

Dissertations

A forest is a highly scattering medium at millimeter wave frequencies. The propagation of cw millimeter wave signals in forests has been studied previously, both theoretically and experimentally. Published experimental data verified that continuous wave transmission is possible over lengths of the order of a few hundred meters and that a forest acts to strongly scatter energy in the forward direction. The cw studies yielded the determination of the range dependence, beam broadening effects and depolarization effects of millimeter wave signals in a forest. However, pulse broadening effects, which are of importance particularly in the case of digital signal transmission, …

Accurate Calibration Of The Four-Detector Photopolarimeter With Imperfect Polarizing Optical Elements, R. M.A. Azzam, Ali G. Lopez

Electrical Engineering Faculty Publications

The first three columns of the instrument matrix A of the four-detector photopolarimeter (FDP) are determined by Fourier analysis of the output current vector I(P) as a function of the azimuth angle P of the incident linearly polarized light. Therefore 12 of the 16 elements of A are measured free of the imperfections of the (absent) quarter-wave retarder (QWR). The effect of angular beam deviation by the polarizer is compensated for by taking the average, (1/2) [I(P) + I(P + 180°)], of the FDP output at 180°-apart, optically equivalent, angular positions of the polarizer. The remaining fourth column of A …

The Electrical Characteristics Of Semi-Insulating Gallium Arsenide A Material For High Power Switches, David Clifton Stoudt

Electrical & Computer Engineering Theses & Dissertations

An experimental study of the electrical characteristics of semi-insulating gallium arsenide has been performed. The goal of this research was to aid in the development of an electron-beam controlled high-power semiconductor switch. The electrical characteristics were found to be heavily dependent on the deep level configuration of the material being investigated. Two methods of deep level characterization are discussed and their results are compared to the information given by the material manufacturer. Studies were conducted to determine both the steady-state and transient dark current characteristics of the switch. Along with being a function of the applied voltage and the deep …

Evaluation Of Sorting Algorithm Performance On Single Instruction Multiple Data Machines, Dong Kuen Yang

Theses

Partitioning an application program into several tasks and executing them via parallel processing is one way to increase computation throughput and performance. But with a uniprocessor system, the performance increase will be minimal. Computer scientists have developed several multiprocessor systems to gain more speed in computation.

There are several computer architectures, such as pipeline machines, array processors and multiprocessor systems. They provide a parallel execution environment to increase the execution speed. But as the system becomes more complex, the communication traffic density between several processors increases more heavily. It has to provide some kind of control algorithm or routing function …

Manufacturing Workstation Model Using Petri Nets, Reni Alexander

Theses

Petri nets have become a powerful tool for modeling and analyzing asynchronous concurrent systems. In this thesis I apply Petri nets for analyzing and modeling a flexible manufacturing workstation (FMS). A manufacturing workstation is modeled by using Colored- Timed Petri nets, with the consideration of tool handling, raw materials, quality checking and the reuse of reworkable scraps. A simulation program for a simplified Petri net model of manufacturing workstation is described and the production throughput is computed.

Adaptive Transform Coding Of Video With Motion Compensation And Vector Quantization, Jung-Hui Chien

Theses

This thesis proposes an efficient transform coding scheme for the low bit rate video sequence. The redundancy within adjacent video frame is exploited by motion compensated interframe prediction using the efficient independent orthogonal search technique, and the motion compensated frame difference (MCFD) signal is transform coding by 1-D DCT, 1-D HDCT and 2-D DCT, the coefficients are zonal masked, and vector quantizatied adaptively. The encoded MCFD as well as the motion information and variance grouping (side informations) are transmitted to the receiver to reconstruct the frame. The transform MCFD signal is classified into the four groups according to the coefficient …

Reliability Prediction Of Vulcanized Fibre Using Electrical Noise As A Screening Parameter, George A. Donos

Theses

The main objective of this thesis was to find a correlation between the electrical noise generated within the body of Vulcanized Fibre in insulating service and the time of its breakdown under a synergy of electrical, thermal and mechanical stresses. Failure was defined as a material discontinuity, puncture, under accelerated life test conditions. Radio frequency measurements of the partial discharges occuring in the voids of the material were performed on 1240 samples of vulcanized fibre with 10 mil thickness. The level of electrical noise measured was used to classify the specimens into the three following categories: (a) Low Noise:0-2.8μV (0-9db), …

Robotic Arms With Flexible Links As The Links Approach Rigidity, George A. Downes

Theses

The dynamics of single link flexible robotic arms are modeled using the Bernoulli-Euler beam equation and Lagrange's equation. The Bernoulli-Euler beam equation derivation is reviewed and is studied in the limiting case as the flexiblity approaches zero. Using the Bernoulli-Euler beam equation, a procedure is developed to calculate the position of the endpoint of a link given the displacement, slope or curvature of any point on the link. Also a procedure is developed to calculate the minimum Young's modulus of elasticity, E, given a specified endpoint displacement tolerance.

A rigid link model based on Lagrange's equation and a flexible link …

Recursive System Identification Using Least Squares Method, Gholamreza Ghorbani Moghadam

Theses

Input and output sampling, in addition to computer simulations, are now an integral part of system identification. In this thesis, the concept of analyzing any time invariant continuous deterministic system will be developed by identifying a linear discrete - time system equivalent to the continuous one. In this method, two computer programs are written in pascal. The first program applies the Recursive Least Squares Method to discrete - time systems in order to estimate the system components. The second program estimates the future output of the system. Four systems have then identified using the programs.

In this process, system identification …

Design And Analysis Of An Intracranial Pressure And Temperature Sensor Telemetry System, Anshumat Parasar

Theses

This thesis presents a signal conditioning and telemetry system for an implantable pressure and temperature transducer. The initial target application is for measuring the epidural intracranial pressure in the range of 25-100 millitorr and temperature over the range 90 — 110° F. The implant, based on custom silicon IC design can be packaged within a volume of 2cm3 and will require surgical procedures for placement and removal. Effort has been made in this thesis to design the transducer, associated signal conditioning and telemetry circuits for useful operation over a wide range of power supply voltage. The implanted device is powered …

Effects Of N>M Clos Networks On Edge Coloring And Matrix Decomposition Algorithms, Ming-Hsing Lin

Theses

Considered in this thesis are n > m Clos networks on edge coloring and matrix decomposition algorithms. This work uses a two-fold approach to examine the effects of n > m Clos networks on edge coloring and matrix decomposition algorithms. First, edge coloring and matching on bipartite multigraphs are applied to routing on Clos networks. It is demonstrated that edge coloring algorithms which find a minimum edge coloring set up the routing for n > m Clos networks with redundancy. The results presented here indicate that the Euler coloring algorithm has applications on n > m Clos networks because it has fast time complexity …

Protocol Processing Delay Analysis On Ethernet By Simulation Of Njit Ethernet, Jagdish Gangrimal Rangwani

Theses

CSMA/CD based Local Area Networks account for about 75% of the installed LAN base today. As these networks are becoming available for high channel bandwidth, it is important to identify the bottlenecks in these networks. As channels are becoming high speed, bottleneck is shifting from channel to protocol processing. This delay depends on a particular implementation of the protocol and not the protocol standard itself.

This Thesis presents the analysis of delay on Ethernet. To achieve realistic results NJIT Ethernet, as it is configured, is modelled and simulated. Traffic on this network is measured and load on each segment is …

A Cad For Edif Pattern Generation, Mohammad Akram Khan

Theses

Generating a set of test vector for a digital circuit is the most critical step in design and test. It is very important to generate test sequence easily and efficiently. The importance is enhanced by the fact that the simulation database is being used to create test programs. A CAD tool ATPG (Automatic Test Pattern Generator) has been developed to specify and satisfy requirements of designers and test engineers. EDIF (Electronic Design Interchange Format) is followed closely. EDIF targets compatability among foundry services and CAD/CAE systems.

Semiconductor Pressure Sensor And Amplifier With Extended Temperature Range, Abhay Mahadeo Joshi

Theses

In this thesis work, a unique raicrosensor was designed for pressure measurements over the temperature range of -80 C to 125 C. The sensor has CMOS circuitry powered by a single voltage supply. It can be used for military and space applications including monitoring the pressure acting on the nose of the space shuttle.

The sensor consists of a thin silicon diaphragm, which is stressed by external pressure. Four resistors in a Wheatstone bridge configuration are diffused into the diaphragm. The temperature drift in the silicon sensors is dominated by the temperature dependence of the piezoresistive coefficients. The resistors are …

Optimization Of Throughput And Stability For Csma/Cd Channel, Liangshyng Jou

Theses

Multiple access technologies plays an important role in designing distributed computer communication system. Here, CSMA/CD has attracted researchers' attentions in the last ten years. In this paper, based on attributions of the slotted, nonpersistent CSMA/CD system, performance of CSMA/CD channel is analyzed. Adaptive Retransmission Technique is adopted to obtain the maximum throughput. Also, equilibrium contours are derived to discuss the stability of the system. And use FET to measure the stability of CSMA/CD channel that FET gives an approximate measure of the average uptime of an unstable channel.

Analytical Determination Of The Complex Dielectric Function Of An Absorbing Medium From Two Angles Of Incidence Of Minimum Parallel Reflectance, R. M.A. Azzam

Electrical Engineering Faculty Publications

The real and imaginary parts of the complex dielectric function (or complex refractive index) of an opaque substrate or a thick film can be determined from two pseudo-Brewster angles measured in two transparent incidence media of different refractive indices. This two-angle method is simple in that it involves no photometric or polarimetric analysis and in that the solution for the optical properties in terms of the measured angles is explicit, analytical, and direct (i.e. noniterative). The two-angle method is demonstrated for an opaque TiN film on a Cleartran ZnS substrate as a specific example. The effect of angle-of-incidence errors on …

Optimal Algorithmic Testing Of Re-Programmable Logic Arrays, Arvind Chopra

Theses

This research delineates a test strategy and detailed sequence of test vectors for a new class of programmable logic devices (PLDs). This new class of devices is based on architectures that contain programmable logic arrays (PLAs) programmed by on chip integrated static RAMs or EEPROMS. The new PLD architecture poses unique testing problems which require 100% nodal test coverage. Previous PLAs/PLDs did not require that 100% of the nodes be tested since their circuits utilized fuse link crosspoints and were not dynamically reprogrammable. Such devices could be tested by a unique personality pattern that combined the application and the test …

Design Of Robotic Lan Controller And Map Interface, Jayesh M. Joshi

Theses

An application specific integrated circuit has been designed for use as a gateway between two local area networks. This silicon chip provides the gateway function to link the NJIT robotics network and the MAP IEEE-standardized network. This IC utilizes the available Motorola MC 68824 Token Bus Controller for the MAP data path. A special IO design compatible with an optical communication link is used to interface into the NJIT RLAN network.

The gateway IC serves as an asynchronous buffer between the 5Mbps MAP link and the 500 bps local optical link. The control protocol provides the master function for polling …

Fault-Tolerant Interconnection Networks For Multiprocessor Systems, Hamed Mohamed Nassar

Dissertations

Interconnection networks represent the backbone of multiprocessor systems. A failure in the network, therefore, could seriously degrade the system performance. For this reason, fault tolerance has been regarded as a major consideration in interconnection network design. This thesis presents two novel techniques to provide fault tolerance capabilities to three major networks: the Baseline network, the Benes network and the Clos network.

First, the Simple Fault Tolerance Technique (SFT) is presented. The SFT technique is in fact the result of merging two widely known interconnection mechanisms: a normal interconnection network and a shared bus. This technique is most suitable for networks …

The Applicability Of Parametric Inverse Scattering For Optical Waveguides With Imperfect Boundaries, Hyoung Jin Choi

Theses

In this thesis, the applicability of an inverse scattering technique for an optical waveguide with imperfect boundaries is investigated. The inversion of imperfect boundaries of waveguides is different from usual inverse scattering algorithms because only eigenmodes can propagate in a waveguide. We suggest a parametric inversion method based on the first-order coupled mode equation. The validity and usefulness of the method are demonstrated using examples of periodic and almost periodic imperfect boundaries.

Adaptive Subband Video Coding With Motion Compensation, Manjunatha S. Kadur

Theses

An efficient scheme for video sequence coding is presented here. The interframe redundancy present in the video sequence is exploited by motion compensation using the efficient independent orthogonal search technique, which requires least number of computations in the worst case. The motion compensated frame difference signal is encoded with a new technique — subband adaptive vector quantization.

Subband coding like transform coding results in signals of unequal energy patterns, which is efficiently utilized for bit allocation. In addition, the subband approach offers means for efficient (but suboptimal) Vector Quantization (VQ) by splitting the signal into several signals. By rate distortion …

Integrated Voice/Data Services On Multihop Radio Networks, Chialun Lu

Theses

Integrated voice/data is the first step toward Integrated Services Digital Networks (ISDN). Various techniques have been proposed and analyzed for multiplexing voice and data over a large bandwidth channel. Network efficiency is what we are most concerned about. In this paper, we address the problem of determining optimal access policies for a tandem ISDN network by using Dynamic Programming. Computer simulation shows that optimal policy minimizes the data delay.

Study Of System Dynamics In A Primitive Identification/Counter Model, Zofia Monczka

Theses

Previous study of a simplified identification/counter model (1), (2) indicated bifurcations in its behavior. In order to study this topic, graphical representations of the system dynamics are derived. Analysis of the structure of the identification/counter model reveals the reasons why the graphs assume their given shapes.

The graphical representations of the system are used to characterize the system behavior and thus explain the bifurcations previously encountered. These representations are then used as the basis for deriving a general model for system behavior. Analysis of this model for a specific range of parameter values indicates that the system contains numerous additional …

Caldac, A New Approach To Computer-Assisted Theatrical Lighting Design, David William Zalewski

Theses

CALDAC, which stands for Computer-Assisted Lighting Design and Control, is a design environment integrating two present day state-of-the-art theatrical lighting computer aides, the computer-aided design (CAD) program and the preset storage system. The CALDAC environment also features On-Screen Stage Simulation, a newly proposed design tool. It is shown that this integration offers a strong advantage to the lighting designer and his/her crew.

The thesis begins by introducing the concepts of theatrical lighting design and the evolution of computerized control. The basics of CAD for the lightplot design are presented, followed by an introduction to the concepts of on-screen stage simulation. …

Visual System Modeling And System Response Analysis, Zhongquan Li

Theses

Based on the anatomical structure, a structural model of the visual system was established. System responses of different stimulations were analyzed based on the model. More extensive study was made on the system impulse response. A mathematical model with parameters representing prominent process components was developed to represent the system response in a compact form and the parameters were statistically studied to correlate to the real physiological characteristics of the visual system. The parameters of the model were used to fit the system intensity response function. The result shows that it is a more quantitative way to construct the system …

User Interactive Compensation For Si/So Systems Via Root-Locus, Shih-Mim Liu

Theses

A powerful computer-aided root-locus method is described and applied to the compensation for SI/SO systems. The approach is based on the concept of continuation methods in which the solution of a parameterized family of algebraic problems is converted into the solution of a differential equation and incorporates the quadratic synthetic division technique. The root-locus is obtained in a systematic manner by numerical integration. Breakaway points are analyzed and classified according to the properties of higher order derivatives. A Turbo Pascal(4.0) program which utilizes the algorithm has been written.

Nonlinear Variants Of The Least Mean Square (Lms) Algorithm, John George Van Saders

Theses

Adaptive systems using the LMS algorithm or its variants usually require bilinear correlation multipliers with high dynamic range and large bandwidth. The class of LMS-type algorithms utilizing zero-memory limiters (on one or both correlation multiplier inputs) to reduce dynamic range are examined. The correlator limiters may be included to simplify the hardware implementation or may arise due to limited dynamic range of the loop components. The application of a theorem due to Price provides a technique for simplifying the analysis, which otherwise might be extremely difficult. The analysis provides closed-form expressions for the mean weight convergence behavior, permitting examination of …

Arithmetic Pipeline Analysis Package Ii, Sai K. Vedantam

Theses

This work describes the implementation of arithmetic pipeline scheduling algorithms, to enhance an existing simulation package. The user need only specify the arithmetic equations to be processed and the required stage configuration. The program automatically performs the tasks of forming the reservation table, building the pipeline and specifying the input/output connectivity for each segment and multiplexer in the pipeline. This package integrates two existing simulation tools and enhances many aspects of the previous programs.

The main application area for such a tool is education. Since it is very easy to use and requires little or no time for one to …

Image Coding With Quantization Noise Feedback, Jen-Chieh Wang

Theses

A progressive image transmission based on Laplacian pyramid structure is used for the scheme of quantization noise feedback. Because a reduction in transmission rate inevitably increases the quantization noise and degrades the image quality, the designer of the quantizer laces the dilemma of balancing the transmission rate and the quantization noise. Using the algorithm of noise feedback will reduce the quantization error without appreciably increasing transmission rate. Uniform quantization and nonuniform quantization rate used to compare the result with or without noise feedback. In the transmitter end, the original image can be reduced by a certain procedure to form a …