Electrical and Electronics Commons^™

Energy Harvesting & Recapture From Human Subjects: Dual-Stage Mems Cantilever Energy Harvester, Nicholas P. Sullivan

Theses and Dissertations

Recent thermal energy harvesting research has advanced alternative non-Seebeck devices and shifted attention towards applications with low temperature differentials near ambient. This research effort takes a simulation-based approach to improve the performance of a modified dual-stage MEMS cantilever energy harvester. The device employs a bimetal and a piezoelectric transducer to harvest energy from a 10° C temperature differential. The proposed application for the device is as a wearable energy harvester, capable of generating power from the human body using skin temperature (average 33° C) as the hot side and ambient air (23° C) as the cold side. A bimetal thickness …

Characterizing Multiple Wireless Sensor Networks For Large-Scale Radio Tomography, Tan Van

Theses and Dissertations

Radio Tomographic Imaging (RTI) is an emerging Device-Free Passive Localization (DFPL) technology that uses a collection of cheap wireless transceivers to form a Wireless Sensor Network (WSN). Unlike device-based active localization, DFPL does not require a target of interest to be wearing any kind of device. The basic concept of RTI utilizes the changes in Received Signal Strength (RSS) between the links of each transceiver to create an attenuation image of the area. This image can then be used for target detection, tracking, and localization. Each transceiver in the WSN must transmit sequentially to prevent collisions. This is not a …

Verification And Validation Of Monte Carlo N-Particle 6 For Computing Gamma Protection Factors, William J. Erwin

Theses and Dissertations

This thesis examined the suitability of a particle simulator known as "Monte Carlo n-Particle 6" (MCNP6) to determine how well U.S. Army vehicles shield their occupants from gamma radiation. MCNP6 compared favorably to three alternate modeling approaches and another particle simulator. In a validation experiment, MCNP6 was found to produce a gamma protection factor within 5% of the experimental result with 95% confidence. Further evaluations validated MCNP6's ability to produce reliable results with simplified or approximated inputs, model different sources, and position those sources in different shielding geometries. MCNP6 is suitable for evaluating gamma protection of Army vehicles and further …

Iii-V Nitride Based Microcantilever Heaters For Unique Multimodal Detection Of Volatile Organic Compounds At Low Temperature, Ifat Jahangir

Theses and Dissertations

Detection of volatile organic compounds (VOCs), which are widely used in industrial processes and household products, is very important due to significant health hazards associated with them. VOCs are commonly detected using photo-ionization detectors (PIDs), suspended hot bead pellistors, or heated metal oxide semiconductor functionalization layers. However, these techniques used for detecting VOCs often suffer from one or more of the following issues - high power consumption, limited selectivity, complicated functionalization technique and expensive characterization tools. On the other hand, microcantilevers offer excellent avenues for molecular sensing that arises out of their high sensitivity to various physical parameter changes induced …

Design Of An All-In-One Embedded Flight Control System, Joel D. Elmore

Theses and Dissertations

This thesis describes an all-in-one flight control system (FCS) that was designed for unmanned aerial vehicles (UAVs). The project focuses on the embedded hardware aspect of a stand-alone system with low-cost and reliability in mind.

Cloud-Induced Uncertainty For Visual Navigation, Alyssa N. Gutierrez

Theses and Dissertations

This research addresses the numerical distortion of features due to the presence of clouds in an image. The research aims to quantify the probability of a mismatch between two features in a single image, which will describe the likelihood that a visual navigation system incorrectly tracks a feature throughout an image sequence, leading to position miscalculations. First, an algorithm is developed for calculating transparency of clouds in images at the pixel level. The algorithm determines transparency based on the distance between each pixel color and the average pixel color of the clouds. The algorithm is used to create a dataset …

Quantitative Comparison Of Time-Frequency Decomposed Gait Emg Signals, L. Patrick Mitchell

Theses and Dissertations

Falls in the senior population represent an immediate threat to both current and future generations’ quality of life. The results of falls can be disastrous, create a long road to recovery, and in many cases result in death. Hypertension represents a difficult-to-quantify condition which is known to contribute to gait and balance dysfunction. Accurate assessment of conditions such as these represents an area of primary investigative need. In order to meet this need, a new experimental setup is developed which combines time-frequency analysis with surface electromyography (sEMG) signals obtained during ambulation. 3-bit pressure data is acquired using a pressure-sensitive mat, …

Removing Parallax-Induced False Changes In Change Detection, Karmon M. Vongsy

Theses and Dissertations

Accurate change detection (CD) results in urban environments is of interest to a diverse set of applications including military surveillance, environmental monitoring, and urban development. This work presents a hyperspectral CD (HSCD) framework. The framework uncovers the need for HSCD methods that resolve false change caused by image parallax. A Generalized Likelihood Ratio Test (GLRT) statistic for HSCD is developed that accommodates unknown mis-registration between imagery described by a prior probability density function for the spatial mis-registration. The potential of the derived method to incorporate more complex signal proccessing functions is demonstrated by the incorporation of a parallax error mitigation …

Characterization And Performance Comparison Of Low-Voltage, High-Speed, Push-Pull And Traveling-Wave Silicon Mach-Zehnder Modulators, Tristan A. Latchu

Theses and Dissertations

The well-known power and memory walls are recognized as the current bottlenecks in computing performance, and with the increasing computational load of commonly run applications, it is necessary to nd ways to alleviate the issues presented by the aforementioned bottlenecks. It is therefore necessary to not focus solely on extracting performance improvement by way of changes to the processing architecture, but rather by holistically improving the computing platform, namely the communications backbone. This work focuses on the characterization and performance comparison of two families of optical data modulators, both fundamentally Mach{Zehnder modulators (MZMs); namely, a modulator with a Push-Pull (PP) …

Blind Demodulation Of Pass Band Ofdma Signals And Jamming Battle Damage Assessment Utilizing Link Adaptation, Nicholas A. Rutherford

Theses and Dissertations

This research focuses on blind demodulation of a pass band OFDMA signal so that jamming effectiveness can be assessed; referred to in this research as BDA. The research extends, modifies and collates work within literature to perform a new method of blindly demodulating of a passband OFDMA signal, which exhibits properties of the 802.16 Wireless MAN OFDMA standard, and presents a novel method for performing BDA via observation of SC LA. Blind demodulation is achieved by estimating the carrier frequency, sampling rate, pulse shaping filter roll off factor, synchronization parameters and CFO. The blind demodulator's performance in AWGN and a …

Selectively Tuning A Buckled Si/Sio2 Membrane Mems Through Joule Heating Actuation And Mechanical Restriction, Kyle K. Ziegler

Theses and Dissertations

This research followed previous work and attempted to modify the spring in two ways. First, a Ti/Au meander resistor was deposited atop the membrane in an effort to actuate the membrane and change the spring constant. Secondly, a series of overhanging cantilevers were attached to the bulk substrate surrounding the membrane in an effort to constrain the membrane buckling deflection to the negative stiffness region. Membrane buckling was investigated through Finite Element analysis (FEA) and analytical equations. Deflections were measured using an interferometric microscope (IFM) and force/deflection measurements were captured using a unique measurement scheme. The results concluded that by …

Electrical Characterization Of Spherical Copper Oxide Memristive Array Sensors, James P. Orta

Theses and Dissertations

A new System Protection (SP) technology is explored by using electrical and mechanical interference-sensing devices that are implemented with granular memristive material. The granular materials consist of oxide-coated copper spheres with radii of about 700 µm that are placed in contact to produce thin oxide junctions which exhibit memristive behavior. Processes for etching, which compared acetic acid and nitric acid etches, and thermal oxidation at 100°C are performed and compared to produce copper spheres with a copper oxide layer over the sphere surface. Oxidized copper spheres are tested as sensor arrays by loading into a capillary tube in an aligned …

Memristive Responses Of Jammed Granular Copper Array Sensors To Mechanical Stress, Gary A. Willey

Theses and Dissertations

A granular memristive device with the end goal of creating a novel system protection device is introduced in a 1-Dimension array. The electromechanical network will lay the groundwork for future 2-Dimensional and 3-Dimensional devices for simultaneous protection from intrusion. Off the shelf copper spheres with diameter of 710 ± 11microns were found through nano-indentation measurements to have elastic modulus of 106GPa, and compressive yield strength of 729MPa, these spheres were prepared for test in a 1-Dimensional array device. The arrays response to mechanical perturbations modeled by Hertz contact mechanics can be monitored by simultaneous electrical measurements across the multiple metal-insulator-metal …

Opportunistic Access In Frequency Hopping Cognitive Radio Networks, Ethan S. Hennessey

Theses and Dissertations

Researchers in the area of cognitive radio often investigate the utility of dynamic spectrum access as a means to make more efficient use of the radio frequency spectrum. Many studies have been conducted to find ways in which a secondary user can occupy spectrum licensed to a primary user in a manner which does not disrupt the primary user's performance. This research investigates the use of opportunistic access in a frequency hopping radio to mitigate the interference caused by other transmitters in a contentious environment such as the unlicensed 2.4 GHz region. Additionally, this work demonstrates how dynamic spectrum access …

Polarimetric Calibration And Characterization Of The Telops Field Portable Polarimetric-Hyperspectral Imager, Joel G. Holder

Theses and Dissertations

The Telops polarimetric-hyperspectral imager combines polarimetric and hyperspectral technologies to enable enhanced scene characterization. The Defense Threat Reduction Agency funded research at AFIT to leverage this capability to provide more accurate scene information to radiation transport models that will allow for more effective location of radiation sources within a region of interest. To support the objectives of the DTRA effort, there is a requirement for highly accurate radiometric, polarimetric, and spectral data on a pixel-by-pixel basis. The complex nature of the Telops instrument combined with working in the thermal IR waveband makes achieving this accuracy a challenge. This thesis develops …

Quantum Efficiency Enhancement For Gan Based Light-Emitting Diodes And Vertical Cavity Surface-Emitting Lasers, Fan Zhang

Theses and Dissertations

This thesis explores the improvement of quantum efficiencies for InGaN/GaN heterostructures and their applications in light-emitting diodes (LEDs) and vertical cavity surface-emitting lasers (VCSELs). Different growth approaches and structural designs were investigated to identify and address the major factors limiting the efficiency. (1) Hot electron overflow and asymmetrical electron/hole injection were found to be the dominant reasons for efficiency degradation in nitride LEDs at high injection; (2) delta p-doped InGaN quantum barriers were employed to improve hole concentration inside the active region and therefore improve hole injection without sacrificing the layer quality; (3) InGaN active regions based on InGaN multiple …

Electron – Phonon Interaction In Multiple Channel Gan Based Hfets: Heat Management Optimization, Romualdo A. Ferreyra

Theses and Dissertations

New power applications for managing increasingly higher power levels require that more heat be removed from the power transistor channel. Conventional treatments for heat dissipation do not take into account the conversion of excess electron energy into longitudinal optical (LO) phonons, whose associated heat is stored in the channel unless such LO phonons decay into longitudinal acoustic (LA) phonons via a Ridley path. A two dimensional electron gas (2DEG) density of ~5×10¹²cm^-2 in the channel results in a strong plasmon–LO phonon coupling (resonance) and a minimum LO phonon lifetime is experimentally observed, implying fast heat removal from …

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Characterization Of Metal-Insulator-Transition (Mit) Phase Change Materials (Pcm) For Reconfigurable Components, Circuits, And Systems, Brent L. Danner

Theses and Dissertations

Many microelectromechanical systems (MEMS) use metal contact micro-switches as part of their reconfigurable device design. These devices utilize a mechanical component that can wear down and fail over time. Metal insulator transition (MIT) materials, also known as phase change materials (PCMs), exhibit a reversible transition that can be used to replace the mechanical component in reconfigurable devices. In the presence of a thermal or electric field stimuli, the PCMs will transition back and forth between a crystalline and amorphous state. During this transformation, the resistivity, reflectivity, and Young's modulus of the material drastically change. This research effort focuses on characterizing …

Constitutive Parameter Measurement Using Double Ridge Waveguide, Nathan J. Lehman

Theses and Dissertations

Electromagnetic materials characterization is important in the design of systems that interact with electromagnetic waves. Determining the constitutive parameters of a material is a vast area of research and practice. For this paper, discussion will focus on a destructive method using waveguides in the frequency range of 6-18 GHz. Traditional methods to perform similar measurements include using coaxial cable, stripline, focus beam and rectangular waveguides. This work will use Double Ridged Waveguide (DRWG) to compare to these other methods and will discuss the attributes and drawbacks of this new approach. The most similar method utilizes rectangular waveguide, so the primary …

Crystal Growth, Characterization And Fabrication Of Cdznte-Based Nuclear Detectors, Ramesh Madhu Krishna

Theses and Dissertations

In today's world, nuclear radiation is seeing more and more use by humanity as time goes on. Nuclear power plants are being built to supply humanity's energy needs, nuclear medical imaging is becoming more popular for diagnosing cancer and other diseases, and control of weapons-grade nuclear materials is becoming more and more important for national security. All of these needs require high-performance nuclear radiation detectors which can accurately measure the type and amount of radiation being used. However, most current radiation detection materials available commercially require extensive cooling, or simply do not function adequately for high-energy gamma-ray emitting nuclear materials …

Stabilizing Controller Design For A Dc Power Distribution System Using A Passivity-Based Stability Criterion, Antonino Riccobono

Theses and Dissertations

In modern times there has been an increased penetration of power electronic converters into Power Distribution Systems. In particular, there has been a strong interest in DC Power Distribution Systems as opposed to conventional AC Power distribution systems. These DC Power Distribution Systems are enabled by power electronics converters. The strong interest is motivated by improvements in power electronic converter technology, like advances in power semiconductor devices, magnetics, control, and converter topologies which have made possible to build high-performance converters at low cost. In many systems, such as cars, ships and airplanes, there has also been a trend towards the …

Design And Analysis Of An Electronically Steerable Microstrip Patch And A Novel Coplanar Waveguide (Cpw) Fed Slot Antenna Array, Hamad Shaban Aldossary

Theses and Dissertations

Conformal Phased Array Antennas (CPAAs) are very attractive for their high gain, low profile, and beam scanning ability while being conformal to their mounting surface. Among them are microstrip patch phased arrays and wideband slot phased arrays which are of particular significance.

In this work, first the study, design, and implementation of a conformal microstrip patch phased array is presented which consists of a high gain beam scanning array implemented using microstrip delay lines controlled using GaAs SPDT switches. Then the study and design of a wideband Coplanar Waveguide (CPW)-fed slot phased array antenna is presented. In both cases the …

Emulation Of An Aeroderivative Twin-Shaft Gas Turbine Engine Using An Ac Electric Motor Drive, Blanca A. Correa

Theses and Dissertations

This dissertation presents a method to use an electric motor to emulate the steady-state and transient shaft power characteristics of an aeroderivative twin-shaft turbine engine. Model-based control provides the framework for developing an aeroderivative twin-shaft engine emulation system. Criteria are developed to appropriately specify the motor and variable-speed drive, based on torque, power, and inertia. This method accounts for the difference in inertia between the engine and the emulating motor; it establishes for the first time the nominal and peak torque requirements of the machine and the peak power and current requirements of the electronic motor drive (inverter).

Our results …

Coordinated Control Of Power Electronic Converters In An Autonomous Microgrid, Gholamreza Dehnavi

Theses and Dissertations

Advances in power electronics and generation technologies have increased the viability of distributed generation systems. A microgrid is a special category of distributed generation systems that is distinguished by its size and the ability to operate independently as an islanded system. As long as a microgrid is connected to a large grid, quality of the voltage is supported by the main grid and each power source connected to the microgrid generates independently. In contrast, in the islanded operation of microgrids and in electrical islands such as shipboard distribution systems, dynamics are strongly dependent on the connected sources and on the …

Modeling Of Sic Power Semiconductor Devices For Switching Converter Applications, Ruiyun Fu

Theses and Dissertations

Thanks to recent progress in SiC technology, SiC JFETs, MOSFETs and Schottky diodes are now commercially available from several manufactories such as Cree, GeneSiC and Infineon. SiC devices hold the promise of faster switching speed compared to Si devices, which can lead to superior converter performance, because the converter can operate at higher switching frequencies with acceptable switching losses, so that passive filter size is reduced. However, the ultimate achievable switching speed is determined not only by internal semiconductor device physics, but also by circuit parasitic elements. Therefore, in order to accurately predict switching losses and actual switching waveforms, including …

Passive Equalizer Topology Analysis For Signal Integrity Applications, Kuo-Lun Yen

Theses and Dissertations

In high-speed, high density PCB bus systems, high frequency signal losses and crosstalk can have great impacts on signal integrity and digital timing, which can distort transmitted signals, worsen eye diagrams, and attenuate signal amplitudes. Also, these impacts make digital signals and their energy smearing over multiple bit positions as known as jitters, and cause the phenomenon of inter-symbol interference (ISI) in digital signal transmissions.

The main objective of this thesis is to analyze and develop efficient topology circuits for compensating bus system high frequency losses by using equalization techniques. The thesis has focused on study of various practical and …

Fault Aware Soft Restart Of An Islanded Microgrid Using An Inverter Coupled Energy Storage System, Asif Anwar

Theses and Dissertations

This research developed a method for autonomous operation of an inverter-coupled energy storage system for safe islanding- re-energization - and reconnection of the facility-island or microgrid to the utility / distribution circuit in a seamless manner in the event of a fault. This enables the energy storage system to function as an autonomous source within the utility power distribution system without the need to re-engineer the existing protection coordination in the distribution system. Fault detection based on voltage measurements from the inverter terminals are used to detect a fault and isolate the energy storage-powered facility with negligible power feed into …

Dislocation Reduction In Silicon Doped High Aluminum Content Algan Layers For Deep Uv Optoelectronic Devices, Hung-Chi Chen

Theses and Dissertations

III-Nitride based deep ultraviolet (UV) light emitting diodes (LEDs) are prospective candidates to replace the conventional bulky, expensive and environmentally harmful mercury lamp as new UV light sources, used in the applications of water and air purification, germicidal and biomedical instrumentation systems, etc. Due to the lack of native substrates and poor carrier injection, AlGaN-based deep UV LED is suffering from low optical power and low overall efficiency, which prevents the availability of low cost, high efficiency deep UV LED on the market.

This dissertation is focused on improving the efficiency of deep UV LEDs, by improving the base template …

Fault Protection In Dc Distribution Systems Via Coordinated Control Of Power Supply Converters And Bus Tie Switches, Pietro Cairoli

Theses and Dissertations

A new fault protection method responds to the current needs of emerging dc power distribution systems by coordinating electronic power converters and mechanical contactors to rapidly isolate short circuit faults while maintaining continuity of power to loads. This work is important because the increasing performance, higher efficiency, and decreasing cost of electronic power converters have spurred a rediscovery and proliferation of dc power distribution systems. Although dc distribution offers advantages such as higher transmission efficiency, higher power density, higher reliability, and ease of interfacing asynchronous sources, enthusiasm for adopting dc technologies suffers from widespread concern over the means to protect …