Electrical and Electronics Commons^™

Replacement Of Surface Ducted Rays Near Caustics With Guassian Beams, Carlos Javier Ruiz

Theses

Conventional approach to a solution of a wave propagation problem in an inhomogeneous medium is to utilize either rays or modes to represent the wave field. Asymptotic ray theory (ART) starts to fail in the vicinity of caustics due to rays experiencing many reflections. Even uniform representations do not properly correct this deficiency of rays when caustics start to pile up in the far range. One possible alternative is to replace these rays with modal bundles and remainders [1]. A promising technique using Gaussian Beams has been used to represent the total field due to a point or a line …

Design And Optimization Of Nmos Sense Amplifiers For Vlsi Drams, Nimish K. Shah

Theses

The aim of this thesis is to study and optimize the performance of NMOS sense amplifiers used in modern VLSI DRAMs.

Initially dynamic memory cells and popular sense amplifier circuits are surveyed.

A standard five transistor sense amplifier is later chosen for detailed analysis. Layout of the circuit is drawn to get the physical parameters. Using SPICE simulator, various effects of circuit parameters are studied. From these results optimal values of these parameters are arrived at.

Also an effort is made to derive theoretically equations for the latching time of a post amplifier which is the most important part in …

Multi-Channel Arrhythmia Analysis In The Clinical Exercise Electrocardiogram, Shi-Xiong Yang

Theses

This thesis studied methods of using 2 channel ECG signals for noise elimination and arrhythmia detection. Clinical data were recorded from patients stress tests and were stored on diskettes for off-line processing. Spatial velocity vector and noise estimation methods in addition to analog and digital filters were combined to remove the noise produced from different sources. Feature extraction and matched filter methods were employed for classification of normal and abnormal QRS complexs, while rhythm computing was used in addition for PVCs and other arrhythmia discrimination. This algorithm was tested on clinical stress test recordings and a computer simulated arrhythmia recording …

Microcomputer Local Area Network Interface, David W. Juan

Theses

A Microcomputer Local Area Network Interface system for use in the study of Local Area Network has been built and tested. The special feature of the system is data transmission/receiving and error detection/recovery. The system adapted the International Standards Organization (ISO) Open System Interconnection COSI) model. It used the star topology and implemented the physical layer, data link layer and network layer. The results of the system indicated the data communications and resources—sharing between microcomputers.

An 8052 Ah - Basic, Based Development System, Suresh Vishwanath Leley

Theses

This project exploits the latest in microcontrollers-an entire environment for developing and prototyping a microcontroller application. With one key chip, a little glue, and a Dumb terminal a powerful system is achieved at a vanishingly small cost. This "one chip" system is adequate for realizing a wide range of applications calling for a small computer or an embedded processor.

Besides economy of system cost, the turn around time from concept to functioning application can be extremely short, even when the development engineer is not particularly well acquainted with traditional assembly language and microprocessor development practices. This economy is achieved by …

Linearization Accuracy In Probabilistic Load Flow, Guan-Zhong Liang

Theses

This paper presents a linear load flow method which can be used for probabilistic load flow analysis. The method is based on least-square estimation. To estimate its accuracy in linear load flow calculations, the method and a previously developed linear load flow method are applied to a typical power system and the results evaluated. Comparable accuracy is noted.

An Analysis Of Minimum Shift Keying From The Viewpoints Of Quadrature Multiplexed And Multi-H Continuous Phase Modulation Signaling, Alfred Anthony De Seta

Theses

Minimum Shift Keying (MSK) is a bandwidth efficient modulation scheme which offers superior performance over Quadrature Phase Shift Keying (QPSK) and Offset Quadrature Phase Shift Keying (OQPSK). This paper discusses these modulation techniques from a quadrature multiplexed signaling viewpoint and compares them in terms of error performance, bandwidth properties and bandlimiting and hardlimiting effects. MSK is also considered as a special case of a multi-h Continuous Phase Modulation (CPM) signal and the Viterbi algorithm is presented as an optimal detection scheme for this class of signals. A computer simulation is performed with the VA as the detection mechanism for an …

Reliability Study Of Liquid Crystal Display, Kalpesh Mahendra Desai

Theses

The purpose of this thesis is to study the reliability of liquid crystal display under different temperature conditions. To accomplish this, accelerated life testing was done on the soft glass and the hard glass liquid crystal display units at 77 C and 85 C temperature without any added humidity or voltage.

As the current is a usefu1 indicator for probable wear of liquid crystal display, leakage current was measured at 0 hour, 1000 hours, 2000 hours and 3000 hours when the units have stabilized at room temperature.

The date shows higher spread for the hard glass units. This may indicate …

A Computer Aided Manufacturing System For Small Quantity Prototype Board Production, Santiago Garcia-Perez

Theses

A matrix addressed manufacturing tool has been built, tested, and integrated in a system aimed to exploit wire-wrap wiring technology for protoboard production in small quantities. Extensive software exploits the power and economy of the personal computer as a superb manufacturing tool and documentation system. Computer graphics are used as a visual aid that takes advantage of the cognitive capabilities of the human mind and eliminates the boredom and high costs involved with heavy automation achieving instead a tolerable level of human engagement with significantly increased efficiency. The approach presented is new and delivers substantial gains in productivity. The software …

The Gpib User's Manual For Hx-40, Ding-Tang Li

Theses

A completed RS-232 to GPIB interfacing system has been built for HX-40 to master the GPIB oriented machine through its serial port. GPIB commands and data can be transfered between HX-40 and the slave station, which is a HP 3582A spectrum analyzer in this project. The data acquisition from serial to GPIB is done by a well-made GPNET mode 10 interfacing board in a transmitting rate of 9600 baud rate. GPNET exchanges data and commands with HX-40 through a RS-232 port, and passes them to the slave station through a GPIB port which is coordinated by GPIB protocol. A software …

Dynamic Laryngeal Analysis : Hardware And Software, Augustine Chan

Theses

A data acquisition and analysis system has been built and tested for the study of laryngeal dynamics: The system uses a computer to control the digitizing rate and to coordinate the pitch prompting for the subject. Tokens of steady state laryngeal vibration are obtained from an electroglottograph when the subject intones a series of computer prompted pitches in a musically scalar sequence. The system digitize the data at a basic rate of 200 samples per laryngeal cycle: This procedure enables the system to perform a modal analysis of laryngeal function: The signal processing and analysis procedure developed displays voice registration …

The Interfacing Between The A/D Converter, Buffer Memory And Hx-40 Microcomputer, Yu-Hwa Chu

Theses

The data acquisition system which includes A/D converter, buffer memory, and address generator, is to digitize the signal for the computer use. The special feature of this system is the computer controlled digitizing rate over a range from 35K to 0.

The interfacing between Motorola 68000 E.C.B. to H.P. 64000 Development System is the simple example for data communication. How to make the protocal to be compatible is the main point. H.P. 64000 is treated as a host computer because it has the capability for data management and large memory for storing data.

Design Of Code Division Multiple Access Systems, Nakrendrakumar Patel

Theses

The intent of the work "Design of Code Division Multiple Access systems (CDMA) " is to consider different aspects of design with their effect on system performance. The generation of binary shift register sequences, that is maximal length sequences, with their properties are presented. From these maximal length sequences the Gold codes are obtained which are the most suitable approximately orthogonal codes for designing CDMA systems. These are discussed with their specific crosscorrelation properties. An extensive discussion is given of the difficult problem of synchronization, thatis bothacquisitionandtracking of pseudonoise sequences. Different synchronizing methods are discussed along with their relative performance. …

Digital Signal Processing On Tms32010 Evaluation Module And Analog Interface Board, Jiming Sun

Theses

The TMS32010 Evaluation Module (EVM) and Analog Interface Board (AIB) have been used to implement a digital signal processing system. This new system will be the hardware basis for research and development in the DSP field at NJIT in the future. This thesis will serve as a user's guide and overall technical manual for the system.

TMS32010 Assembler, Linker and Simulator in VAX-11 are used to develop the system software, then we can down load the object codes to the EVM through the MODEM in order to test them. By using the A/D and D/A converter as input and output …

Optimization Of Reactive Ionized Cluster Beam (R-Icb) Technique For Deposition Of Gan Films, Veronica S. Kyriacou

Theses

The deposition of GaN film onto glass substrate, using the Reactive - Ionized Cluster Beam deposition technique was studied. The creation of clusters is dictated by various parameters such as the vacuum pressure inside and outside the crucible, the crucible temperature, and the nozzle diameter of the crucible. Optimization of these parameters was experimentally studied, and deposition of gallium films on glass substrates was tried as a first step.

The direct heating method was used at first to get the 1100¬1300°C crucible temperature which was required for the creation of gallium clusters. Although different tungsten wire diameters and different number …

Sputtered Mercury Cadmium Telluride Heterojunction Devices : Electrical Characteristics And Fabrication Process, Ashish N. Mistry

Theses

The main objective of this thesis was to grow high quality epitaxial films of the compound semiconductor Mercury-Cadmium-Telluride (MCT) on Silicon and MCT substrates,using sputtering technology. The research was aimed at investigating the heterojunction behaviour at such interfaces. Detailed studies about the heterojunction theory were made. Devices were made using MCT substrates prepared at the Santa Barbara Research Center (S.B.R. C.),California.

Experiments were designed to grow MCT films with high electron mobility and low carrier concentration in as-grown MCT films and some results were obtained close to reported data for high grade bulk material. Since the parameters involved in sputter …

Design And Construction Of An Atomic Nitrogen Source For Ion Cluster Beam Deposition Of Thin Film Nitrides, Sahar Elgharib

Theses

The objective of this thesis research was to generate atomic nitrogen to react with Ga being deposited by an Ion Cluster Beam method to prepare GaN thin films. An experimental reactor was designed and constructed to generate atomic nitrogen by making use of a microwave induced discharge to dissociate molecular nitrogen into atomic nitrogen. The concentration and the flow rate of the atomic nitrogen arriving at the substrate were measured by titration with nitrous oxide. The experiments were done with 0.32 square cm quartz tubing at room temperature over the nitrogen pressure range from 0.14 torr to 0.56 torr. Results …

Further Development Of Preparation And Measurement Techniques For Triode-Sputtered Mercury Cadmium Telluride Thin Films, Tai-On Chan

Theses

The modified MRC 8800 R.F. triode sputtering system was used for mercury vapor sputtering (Hg^1-xCd^x)Te targets onto N-type (111) silicon substrates with a resistivity of 70 to 90 ohm-cm. Deposition rates were in the 2.6 to 3.6 A/sec range, A Hall mobility value, at 87°K, of 2550 Cm²/V•sec with a carrier concentration of 7(10¹⁵) cm^-3 was obtained for 9 μm thick films with an X-value of 0.25. Obtaining good sputtered films reliably was dependent on having targets that would not crack when bombarded with mercury ions. Improvements in the methods used …

Frequency Characterization Of A Thin Linear Antenna Using Diakoptic Theory, Howard Harold Smith

Theses

A frequency dependent analytical expression for the input impedance of a thin wire antenna is obtained using diakoptic theory. In diakoptic theory the linear antenna is seperated into electrically short segments where each segment is treated as a two-port network. This approach eliminates the need for an integral equation formulation. An impedance matrix is found which characterizes coupling between all segments. By expanding the free space Green's function in a power series in wavenumber k each entry in the resultant impedance matrix is obtained as a function of frequency. Enforcement of the continuity of currents and equality of scalar potentials …

Reliability Evaluation Of Liquid Crystal Displays Under Accelerated Test Conditions, Ravi Sankar Kalyandrug

Theses

This study has determined the effects of high temperature and humidity on the reliability of liquid crystal dis-plays.

Reliability life testing was done on variety of LCD samples under different operating conditions. All the besting was done under accelerated conditions, including high temperature of 85°C and relative humidity of 70%. A number of failure modes were identified in the long series'of tests.

Among many failure modes such as peeling of seal, degradation of polarizers etc., the most important is the degradation of alignment of liquid crystal molecules. Leakage current measurements were made on all the LCD samples before and after …

Present Reliability Of Liquid Crystal Display Devices, C. N. Suresh

Theses

The purpose of this Thesis is to study the life of liquid crystal display devices as at present available in the market place. To accomplish this, accelerated tempera-ture conditions at 77°C and 85°C were used.

During the last few years, there has grown a tremendous interest in wide range temperature operating and fast LCDs. It is therefore important to understand how LCDs behave under these conditions.

The reliability of a liquid crystal display is usually measured in terms of a quantative degradation in electrical performance and a degradation in visual appearance. The degradation in visual appear6knce may manifest itself as …

Robot Manipulators And Control, Theresa Wu

Theses

This paper on Robot Manipulators brings together theories from three fields : computer graphics, kinematic equations and microprocessor based control.

There are four chapters in this paper, chapter one is the conceptual development on homogeneous transformations, express the position and orientation of the transposition of an object in Cartisian coordinates. Chapter two develops the method of obtaining the Cartisian coordinate position and orientation of the end effector for a manipulator, give the joint coordinate as input and use the homogeneous transformation to express the position and orientation. Chapter 3 is a very difficult one; it solves the parameters for the …

Identification Of Linear System With Feedback Input, Jyh Yang

Theses

A new procedure with feedback input is presented for identification of continuous-time systems. Using Lyapunov's direct method to prove it asymptotic stability. For the procedure to be applicable, it's assumed that all the state variables of the plant are accessible and that there is no measurement noise so the model reference scheme can be used to identify the parameters of the plant.

The procedure results in the convergence of every parameter of a model to the corresponding one of the system as the time approaching to infinite i.e. t→∞. Digital computer simulations are provided to demonstrate the feasibility of the …

Reliability Problems And Failure Mechanisms Of Solid Tantalum Capacitors, Ghanshyam B. Nakrani

Theses

Today, reliability is acknowledged as an important item in design and the operation of the electronic systems.

This thesis provides some theory, and experiments are instituted to evaluate the reliability for SOLID TANTALUM CAPACITORS made by different manufacturers. The experimental life test work was done at high temperature of 9S 2°C and high humidity of 95 ± 3% on transfer molded tantalum capacitors.

Literature study concentrates on the reliability in solid tantalum capacitors developed between 1961 and 1984.

Several failure mechanisms with figures are illustrated to point out how higher reliability of solid tantalum capacitors may be developed.

The bibliography …

A Parameter Identification System For The Human Electroretinogram, Yu-Huai Hsiao

Theses

The human Electroretinogram (ERG) is obtained in a clinical test to detect physiological abnormalities in the eye. A mathematical model of the ERG has been developed, as well as a system to identify its parameters. The system utilizes several computers. The data acquisition and initial processing is done on a previously developed system at the Eye Institute of New Jersey and the University of Medicine and Dentistry of New Jersey, which has been modified to provide the facility for further processing. Software was developed to use a MINC-11/23 computer at New Jersey Institute of Technology to transfer data between the …

Digital Fm-Demodulation Using Digital Signal Processing Techniques, Peter Wagner

Theses

This thesis presents the results of research in the area of digital demodulation of FM signals. The first part of the thesis describes the performance of digital Hilbert-transformers and Differentiators that are optimized in a determined bandwidth. These digital filters are used to build a digital Klapper-Kratt detector. According to this procedure, the coefficients of the digital Klapper-Kratt detectors up to the filter length N=25 are calculated and the resulting discriminator ripple computed and evaluated. One suggested algorithm gives the opportunity to balance the detector at a certain center-frequency. The major part of this thesis describes a new approach towards …

Computerized Instrumentation System For Indirect Measurement Of Metabolic Changes In Rats, Holger Tebbje

Theses

This work describes the further development of a system for the measurement of the energy expenditure of rats. Based on the concept of indirect calorimetry the respiratory exchange is monitored in a controlled experiment. Rats are held in cages through which air is drawn and analyzed. Transducers and sensors, interfaced to the computer, are measuring the composition and the physical parameters of the gas entering and leaving the chambers. The data recieved is processed, displayed on a screen, printed and stored for later analysis.

The accuracy and repeatability of the system improved by measuring additional parameters like barometric pressure and …

Automated Arrhythmia Detection In The Exercise Electrocardiogram, Gregory Ciurpita

Theses

A self-adapting, non-real time method for detecting arrhythmias in single channel Exercise ECG is described. Linear and non-linear digital filtering techniques are used to remove additive noise. A time-varying threshold technique is used to detect R-waves based on amplitude. Feature extraction and matched filter methods are used to classify QRS-waves into existing types, or to create new types. The program works on digitized data from floppy disk and plots all data along with classification results on ReGis graphics terminal or printer. This work will continue so that the system will be capable of processing three-channel ECG in real-time.

An Examination Of The Power Spectral Density Function, James Edward Coleman

Theses

The power spectral density (PSD) function is a characterization of an (ideal) signal or set of signals. It is usually associated with a stationary random process, but it need not be. In fact, to study its properties it is desirable to divorce the power PSD from any extraneous structure that may conceal its properties. Specifically, it is desirable to study Sτ(f) = | Xτ(f)|²/2T and determine how it approximates the power spectrum of a power signal S (f) = τ[R(τ)].

It is shown that it cannot be concluded (contrary to what some of the literature has reported) that …

Digitally Implemented Klapper-Kratt Fm Detector Using The Intel-292o Digital Signal Processor, Chang-Hwan Park

Theses

This thesis describes and analyses a digitally implemented FM detector, which is a new member of the family of FM detectors introduced by Drs. Klapper and Kratt.

The properties of the new detector are low delay, excellent sensitivity, extreme linearity, and compatibility of components with integrated circuit technology.

A working model is implemented by adapting FIR digital s signal processing methods, and is realized using the Single-Chip Digital Signal Processor Intel-2920 which is comprised of micro-processor, scratch-pad data RAMs, program store EPROMs, A/D and D/A conversion circuitry, and I/O circuitry.

The performance of the working model shows very good linearity …