Electrical and Electronics Commons^™

Pscad Modeling Of One-Cycle Control Var, Andre Keir Azares

Electrical Engineering

Voltage support has been a common problem utilities have faced for many years and although there exists many solutions, the advent of renewable energy devices and electric vehicles make the problem of voltage support an even greater challenge today. The increasing use of electronic devices by consumers also increases the magnitude of dealing with voltage support. A promising new solution to voltage support is seen in One Cycle Control, a new control method that uses a nonlinear feedback technique on power electronics to produce high quality sine waves with fast dynamic response. This control paradigm is seen in its application …

Multiplicative Feedback Audio Distortion Circuit, Colton Parsons

Electrical Engineering

This circuit aims to distort an audio signal input in a novel and aesthetically pleasing manner. When it comes to the timbre of a note, even harmonics generally sound better than odd harmonics. Most forms of audio signal distortion (usually for electric guitar) primarily add odd harmonics to a signal, as this is easily accomplished by clipping the waveform. This project instead utilizes a signal multiplier in a feedback loop, with one multiplier input coming from the circuit’s input, and the other from the multiplier’s own output. This process creates even harmonics. A delay line is placed in the loop, …

Cubesat Launch Sequencer, Billy Beecher

Electrical Engineering

I am working with the Naval Postgraduate School to develop a low cost CubeSat launch sequencer for NPSCuL that is designed to operate in low Earth orbit. The system will be capable of providing programmable delays with a minimum delay of one second to a maximum delay of five minutes. Delays must be accurate to within ± 10% or within one second, whichever is less. After the delay, the system will provide the necessary launch signal. To ensure protection from radiation, the system will feature triple redundancy and voting logic stages to ensure that the proper signal is propagated.

Broadband, Rugged, High Linearity, Low-Noise Amplifier, Shane Smith

Electrical Engineering

This report examines the application of a low-noise amplifier module for a Global Positioning System (GPS). This low-noise amplifier module helps allow the carrier signal to get the amplification needed to give a smoother analog to digital conversion. However, the frequency range of the GPS spectrum reaches up to 1.6GHz, where component noise becomes an issue and can create a disrupted signal. This low-noise amplifier needs to create a reasonable gain, while achieving a low noise figure. An amplifier with high gain and low noise figure becomes difficult because they create a design trade-off, higher the gain brings higher the …

Alternative Wheelchair Control System, Jessica Hendricks, Tara Keigharn

Electrical Engineering

We geared this project towards assisting an individual with limited[1] motor function to operate a wheelchair. The product targets individuals who find use of a joystick is ineffective or painful. We focused our design on the wheelchair bought from Adaptive Driving Systems (Driving, 2013); but ultimately we would like to field a final product capable of applying to any electric wheelchair. Our goal: a person to operate the electric wheelchair using sensors that transmit a translation of an individual’s hand movement through a wireless transmission to a microcontroller installed on the wheel chair that then controls the wheelchair’s movement. …

High Frequency Open Air Optical Communication System, Alexander C. Wolff

Electrical Engineering

The goal of this project is to create a wireless optical communication system that operates at high frequencies (up to 3 GHz). The system will function by taking a digital electric input signal, converting it to a photonic signal, recovering the signal at the other end of a short distance (~1 foot) and converting it back into a digital signal. Unlike the more common fiber-optic data transmission systems, this system will transmit light through air, instead of fiber, as its medium. Doing so will have the benefits of a wireless system combined with the benefits from an optical system, including …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Active Diesel Soot Measurement By Laser Opacity, Jonathan Audish, Brian Ko, Edward Ma, Travis Mcdaniel

Electrical Engineering

This project looks into understanding the concentration of soot being omitted by a diesel engine through the creation of an innovative opacity sensor. The system contains a receiver circuit implementing a photodiode, laser with wavelength of 405±10nm, and a microcontroller with analog-to-digital (A/D) converter. As the laser pulsates, the microcontroller collects and processes the data to calculate the amount of soot within the exhaust system. The opacity sensor in our tests will be used on an Isuzu 1.9 liter diesel engine. The elegant design of the system can be integrated into conventional manufacturing molding or casting processes for new exhaust …

Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison

Electrical Engineering

Electronic devices are a part of all modern homes, but restricted by available outlets and the hassle of wires. With the modern wireless mouse, this is also the case. When the battery is low the consumer has several options: it is replaced with a new battery, it can be recharged using a USB wire, or the mouse is placed on a charging dock. This project provides an alternative to these options and allows the mouse’s battery to be charged via wireless inductive coupling. The wireless power charging system that was implemented in this project was successful in its ability to …

3.5 To 30 Mhz Automatic Antenna Impedance Matching System, William Blodgett

Electrical Engineering

Two-way communications using 3 to 30 MHz, high-frequency (HF) radio, also known as shortwave radio, provides worldwide coverage with no infrastructure required between stations. Amateur or “Ham” radio operators apply this advantage to long distance communications and to provide disaster relief communications. Optimum frequencies for long distance propagation are time-of-day variant necessitating an operating frequency range of 3 to 30 MHz. HF half wave dipole antenna length varies from 15 to 150 ft over this range. Fixed-length antenna impedance varies with frequency due to physical dimension dependent capacitance and inductance. Maximum transmitter to antenna power transfer occurs when the transmission …

Cell Phone Charger For The Dc House Project, Andrew Hefner, Antonio Magdaleno

Electrical Engineering

The goal of this project is to create a multiple output cell phone charger for the DC House project. The cell phone charger is essentially a DC-DC converter. The converter takes an input of 48 volts from the outlet in the DC House and decreases the voltage level to 5 volts; the input voltage level of all cellular devices. By designing an isolated flyback converter with initial specification in LTSpice simulation software, a converter was created. By monitoring the input and output voltage and current using the multi-meters and electronic load, we determined the charger to be 71% efficient when …

All-In-One Aprs Transmitter, Justin Kenny

Electrical Engineering

The Automatic Packet Reporting System (APRS) is a digital radio system that allows transmission of data using an analog FM radio link. APRS allows position, brief messages, and other data to be distributed across a network, independent of infrastructure, making it ideal for applications such as search and rescue, asset management, and event tracking, while maintaining low cost and operating even when cellular and internet services are unavailable. This project encompasses the design, build, and test of a compact, low-cost APRS transmitter, which will include a 5W radio, GPS, and LCD-based user interface, to allow full utilization of APRS.

Ignitron Trigger Circuit, John F. O'Hara Iii

Electrical Engineering

No abstract provided.

Pulsed Class-G Rf Amplifier System, Kevin Maulhardt, Kevin Haskett

Electrical Engineering

No abstract provided.

12 Volt Wall Outlet For The Dc House Project, Dylan Van Lant, Chenxi Zhang

Electrical Engineering

The purpose of this project is to build a DC-DC converter for the wall outlet of the DC House. This report focuses on the development of the DC -DC converter, and explains the design process as well as summarize the final results. The proposed system using the Buck or Step Down topology takes input voltage of 48V and output 12V at 100W. Results show the ability of the converter to fulfill such tasks while maintaining efficiency about 90% at all load.

Music Driven Graphical Visualization System, Glenn Bruner

Electrical Engineering

In today’s society, we are able to enjoy listening to music on an assortment of high-tech devices such as home computers, or multimedia players, or personal audio players. A common characteristic of typical audio media players is that they lack the ability to provide visual stimulation in addition to the provided audio stimulus. Large public events, such as concerts, could be enhanced if they included visual effects in addition to audio stimulation. The goal of this project is to provide a graphical visualization that is automatically synchronized to an audio signal with a goal of enhancing the overall musical experience. …

Foce Intermodule Communications System, Roland Quiros

Electrical Engineering

Done in conjunction with Chad Kecy of the Monterey Bay Aquarium Reasearch Institute (MBARI), this project is an expansion of the Free Ocean Carbon Emission (FOCE) project. This iteration created a communications protocol between the different modules in an expandable array of PIC24-based boards.

Day/Night Band Imager For A Cubesat, Eric Stanton

Electrical Engineering

Day/Night Band (DNB) earth sensing and meteorological systems like the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provide visible wavelength imagery 24 hours a day that is used primarily for cloud imaging in support of weather forecasting. This paper describes a compact push-broom imager that meets low light imaging requirements for DMSP OLS and the NOAA/NASA Joint Polar Satellite System (JPSS) as documented in the Integrated Operational Requirements Document [1] (IORD) including the imager design, system level concepts of operation for data collection, radiometric and spatial calibration, and data transmission to Earth. This small, lightweight imager complies with …

Printed Electroluminescent Display, Christopher (Chris) James Nixon, Veronica Kopp

Electrical Engineering

Electroluminescent displays are part of an emerging technology known as printed electronics. Most identify printed electronics with purely electronic purposes such as the Radio frequency identification (RFID). Now the electronics and graphic communication industries have come together to create of new forms of products that interact with customers. Flexible, electronic circuits use functional inks and traditional printing methods such as screen printing, gravure, and inkjet. Printed electronics are perfect for low performance applications, such as displays, labels, clothing and batteries. This paper focuses on creating an interactive electroluminescent (EL) display. In selling a product, displays are important because most customers …

"Auto-Tuned" Stereo, Daniel Montes

Electrical Engineering

The purpose of this project is to determine the capability of introducing delay and gain to audio signals to synthesize a “tuned” experience. The project uses audio operational amplifiers, field effect transistors, a class D amplifier, microphones, speakers, a 32-bit microcontroller for design and testing. When implementing the MOSFET into the all pass filter, the phase delay occurs by varying the transistor resulted in minimal change in phase. MOSFETs are used as variable resistors to vary the phase change and gain. By modifying the gain the synthesized distance from each speaker can be adjusted. Varying the phase change provides the …

Lyfi, Kianoosh Salami, Justin Cotton, Elush Shirazpour

Electrical Engineering

This paper will cover the steps necessary to design, build, and manage networkable smart light switches over WiFi via a mobile application. It contains a microcontroller running a real time operating system, a WiFi module, a Java server with SQLite databasing, and a mobile phone application.

LyFi is designed to turn on/off and dim household lights while only requiring the same installation procedure as a less capable dimmer switch. Once installed and connected to a network, LyFi will self-discover and configure. The server automatically propogates a database of nodes where any mobile device running an application can receive an updated …

Inductive Metal Identification, Paul Maggi

Electrical Engineering

This project focuses on creating a device to differentiate between various types of metals via magnetic induction. Magnetic induction is used because it is both non-optical and non-contact. It achieves this by generating a varying magnetic field, which induces eddy currents in the metal. These eddy currents produce small disturbances in the surrounding magnetic field, which can be sensed with Hall Effect Sensors (HES). The primary challenge in this project was generating a sufficiently strong magnetic field to detectable disturbances. In order to achieve better results, a stronger magnetic field must be used as well as more sensitive Hall Effect …

Portable Solar Powered Charging Station, Jordan Bonner

Electrical Engineering

The portable solar powered charging station uses a solar powered mat that can be folded for portability. The device has the ability to charge small electronics during both day and night. When sunlight is available, the charger charges two C batteries in series and at the same time it charges any electronic device that can be connected via USB or cigarette lighter. At night the charger will charge the same electronic devices from the onboard batteries. The charging station must be able to interface with electronic devices using USB and a car cigarette lighter to charge the device’s battery.

Digital Guitar Effects Unit And Amplifier, Kevin Salvador

Electrical Engineering

This report outlines the design and implementation of a digital guitar effects unit and amplifier. The main portion of this project consisted of the digital equalizer and effects. Several commercial equalizers were researched in order to decide the typical frequency bands and average amount of bands total. Eventually 8 bands were selected. A range of approximately 20Hz-3kHz was chosen based on test data of guitar signals. Popular effects that were incorporated in this project include Distortion, Echo, Reverb, Chorus and Flanger. The digital processor chosen was a Texas Instruments c6713 floating point processor. Designs for the various filters were done …

Car Alarm System, David Lane

Electrical Engineering

This project entails the design and implementation of a car alarm system for a 1977 Volkswagen Beetle.

Rapid Battery Interchange System, Mason Borda

Electrical Engineering

As our nation strives towards a departure from widespread use of fossil fuels, we must focus on a plan for what is to be the substitute for Internal Combustion Engine vehicles as well as the infrastructure to support this. The most popular alternative to the internal combustion engine is the electrically propelled vehicle, one that can provide us with many benefits including simplified construction, lower operational costs, and for the driving enthusiasts more torque. The prevailing issue in the widespread acceptance and use of the electric vehicle thus far is “range anxiety”. Range anxiety is defined as “The fear of …

Equating A Car Alternator With The Generated Voltage Equation, Ervin Carrillo

Electrical Engineering

No abstract provided.

Optical Mode Pattern Study Of Gan Based Leds With And Without Nanoscale Top Grating, Gregory Chavoor

Electrical Engineering

This study analyzes optical confinement factor and light emitting mode order for three different GaN LEDs: a conventional LED, thin Film LED, and thin Film LED with a photonic crystal (PhC) grating. For the first structure, we increase the thickness of Al_xGa_1-xN from 0 to 600nm, alter the x composition in Al_xGa_1-xN from 0.05 to 0.2 in steps of 0.05, and adjust the p-GaN and n-GaN thicknesses each from 0 to 200nm. For the second structure, we alter the n-GaN substrate thickness from 300-1000nm in steps of 100nm and 1000-4000nm in steps …

Auto-Tuning Antenna, John Chen, Jennifer Tighe

Electrical Engineering

Radio transmitters and antennas have differing impedances at the output and feedpoint, depending on frequency. Modern antenna tuning methods involve manual or automatic resistance and reactance network adjustment to match transmitter and antenna impedance. This reduces power reflections to the transmitter, but introduces losses and prevents full transmitter power from being radiated at the antenna. This project utilizes a variable length antenna element to tune and match transmitter and antenna impedances, allowing efficient power transfer to the antenna. The antenna length varies from 0 to 30.5 inches. The method involves an RF signal with a maximum power of 2 watts …

Constant Conduction Angle Experimental Generation For Rf Power Amplifiers, Michael Spahn

Electrical Engineering

As the demand for more devices to become wireless increases, there is a need for linear, efficient monolithic power amplifiers to deal with the variations in modulation of signals. With partial support from Cal Poly C3RP Grant #52268, this paper explains the implementation of and analyzes a circuit that actively biases a bipolar transistor to operate as a Class C amplifier. The Class C amplifier can maintain constant conduction angle over a range of output powers by using a Class B amplifier to force a scaled DC current vs. input magnitude curve on to a Class C amplifier. The knee …