Electrical and Electronics Commons^™

Phase-Sensitive Detection Electronics For Wavelength Modulation Spectroscopy Experiments, Tyrone Pate

Electrical & Computer Engineering Theses & Dissertations

Wavelength modulation spectroscopy (WMS) is a non-intrusive detection technique, which enables the measurement of several parameters such as pressure, concentration, and temperature of a species of interest by analyzing the latter's absorption lineshape profile. The method employs a synchronous modulation and detection apparatus to increase the signal to noise ratio and hence the sensitivity of the measurement. Phase-sensitive detection and demodulation of the signal is performed at the modulation frequency and its harmonics. Research at ODU demonstrates that each particular measurement can be performed optimally at an appropriate harmonic of the modulation frequency. The most suitable harmonic depends on many …

The Effect Of Multiple Pulses On Bacteria, Ramy El-Sayed Aly

Electrical & Computer Engineering Theses & Dissertations

Pulsed electric fields are widely used for bacterial decontamination of water and liquid food [I]. Depending on pulse amplitude and duration, a certain percentage of the bacteria suffer irreversible damage and, consequently, cell death. We have explored the effect of microsecond pulses of 13 kV/cm and 15 kV/cm electric field amplitude on the viability of Escherlchia coli. The pulse duration was varied from 4 μs to 32 μs, and the pulse number of 4 μs pulses from one to eight, Finally, the effect of separation between pulses was studied. The pulses were generated by means of a generator where …

Pulsed Electron Heating Of Atmospheric Pressure Air Glow Discharges, Hisham Merhi

Electrical & Computer Engineering Theses & Dissertations

By applying electric field pulses of short duration (compared to the time constant for glow-to-arc transitions) to a weakly ionized gas, the electron energy distribution can be temporarily shifted to higher energies. This effect causes a nonlinear increase in the ionization rate and consequently a larger electron decay time. This effect has been demonstrated using single pulse operation.³ In order to generate plasma with semi-continuous electron density, repetitive operation is required. As a first step towards repetitive pulsed electric field operation, the temporal development of the voltage across the plasma for two subsequent pulses was measured. The dual pulse …

Evaluation Of The Transport Properties Of Gasb For Bipolar Applications Through Monte Carlo Simulations, Damayanthi Palaniappan

Electrical & Computer Engineering Theses & Dissertations

GaAs is currently the semiconductor material of choice for high speed, low power applications. Its electronic transport properties are superior to almost all other semiconductors. It is also used in a variety of bipolar applications such as photodetectors and photo-mixers. However, as is well known, the hole mobility and related transport parameters of GaAs are not very good. This is a serious drawback, and poses a potential problem for all applications involving bipolar conductivity. In order to increase the high :frequency limits and high-speed capability of bipolar devices, the choice of an alternative material, therefore, becomes necessary. An important first …

Field Enhancement In Silicon Nanotip Field Emitter Arrays, Ajith Varghese

Electrical & Computer Engineering Theses & Dissertations

No abstract.

Development And Testing Of An Ac Micro Hollow Cathode Simulator, Thomas E. Caldwell

Electrical & Computer Engineering Theses & Dissertations

The use of AC source plasma discharge devices in applications such as material processing and film deposition has increased in recent years due to improvements in discharge efficiency made possible by devices such as the micro hollow cathode. Designing hollow cathodes for specific applications requires an understanding of the processes that govern the discharge. Simulation is an inexpensive tool for understanding hollow cathode operation and optimizing the device for specific applications. This thesis describes the development of an AC micro hollow cathode simulator. It details the theoretical models used in the simulation and presents the results of test cases intended …

Stability Analysis And Augmentation Of A Closed-Loop Computer Control System Subject To Electromagnetic Disturbances, Mustafa Doğan

Electrical & Computer Engineering Theses & Dissertations

Most electronic and electrical equipment is not only a potential source of electromagnetic interference (EMI) but can also malfunction when exposed to certain levels of ambient EMI. This phenomena becomes more significant for digital control-computers automating the command and control performances in complex plants. Such EM disturbances can introduce transient signals on analog sensor and actuator lines, change data values on digital buses and in memory, or even produce logic changes in the CPU. The result of these so called computer upsets is the introduction of some degree of degradation in the quality of the control signal ranging from a …

Two Dimensional, Time Dependent Modeling And Simulation Of Semi-Insulating Gaas High-Power Photoconductive Switches, Prakasit Kayasit

Electrical & Computer Engineering Theses & Dissertations

The current-voltage (I-V) characteristics and photoconductive behavior of semi-insulating GaAs (SI GaAs) high-power switches have been investigated by using a two-dimensional, time dependent, drift diffusion transport model. The dc current-voltage behavior as predicted by the results of this model was compared with available experimental data to evaluate the accuracy and validity of the model. The results show very good agreement, Next, research was carried out to investigate the behavior of the switches under high-field operation.

Simulations at high voltages emphasize on the two following processes: (a) The mechanism of impact ionization and the effect of this mechanism on device stability …

Reactions Of Oxygen And Nitric Oxide In A Microhollow Electrode Discharge, Joseph L. Desormeaux Jr.

Electrical & Computer Engineering Theses & Dissertations

Microhollow electrode discharges have been developed and researched in the Physical Electronics Research Institute Laboratories. This discharge typically operates in direct current mode. Microhollow electrode discharges are non-thermal discharges that produce electrons with energies greater than 10 electron volts. Passing gas mixtures through non-equilibrium discharges invokes excitation or dissociation of gas molecules.

The scope of my research was to study the effect of the discharge on the chemistry of two gases, oxygen and nitric oxide in nitrogen mixture. Initial experiments were performed in an effort to produce ozone near atmospheric pressure. This seemed possible since the discharge has a high-energy …

Coupled Electrodynamic-Monte Carlo Simulations Of Nanoscale Gaas Terahertz Optical Mixers, Jiang Li

Electrical & Computer Engineering Theses & Dissertations

The concept of mixing or heterodyning has traditionally been used for microwaves and for radio frequency communications. However, the concept can easily be extended into the optical frequency regime. By doing so, the photomixing process can serve as a very versatile tool for both the generation of ultrahigh frequency (terahertz) and the detection of weak optical signals.

The aim of this thesis is to perform a theoretical study of the photomixing process inside GaAs devices as the non-linear elements. A coupled approach which combines the Monte Carlo simulation scheme for the carrier transport, with Maxwell's equation for the electrodynamics, has …

Electrical Characteristics And Parallel Operation Of Microhollow Cathode Discharges, Wenhui Shi

Electrical & Computer Engineering Theses & Dissertations

This thesis describes the electrical properties of microhollow cathode discharges with argon as filling gas. The appearance and current-voltage characteristics of microhollow cathode discharges have been recorded. Three kinds of discharge modes (predischarge, hollow cathode discharge and abnormal discharge) have been observed. The range of operation of the hollow cathode discharge has been found to be 0.5 < pD & 5 Torr cm in argon. By reducing the hole diameter to 100 pm, we were able to operate the discharge to atmospheric pressure in a dc mode. The possibility of dc parallel operation of microhollow cathode discharges was explored. Parallel operation could be obtained without individual ballast for discharges with a positive I-V slope greater than 10 V/mA over a voltage range of more than 5 % of the sustaining voltage. For parallel operation outside the range the ballasting is required. This model was explored by using a segmented anode model. The result of the simple calculation coincides well with the experiment result, where a semi-insulator silicon was used as distributed ballast.

High Pressure Radio-Frequency Microhollow Cathode Discharges, Anja Annett Muller

Electrical & Computer Engineering Theses & Dissertations

A new field of microhollow cathode discharges is represented by the RF microhollow cathode discharge. So far, the behavior and related physical processes of the RF microhollow cathode discharge are not well investigated.

RF microhollow discharges in air at high pressures were investigated under different experimental conditions. The geometry was changed by reducing the cathode hole diameter and the dielectric spacer thickness. By adding a noble gas to air, the influence of additive gases was explored. Additionally, the parallel operation of RF microhollow discharges was investigated.

It was shown that stable RF microhollow cathode discharges could only be sustained up …

A Piezoresistive Metal Thin Film Tilt Sensor, Todd Allan Lindley

Electrical & Computer Engineering Theses & Dissertations

Thin film strain gauges have many applications as transducers for monitoring pressure, vibration, and acceleration. In this thesis, a simple system, consisting of a Nichrome thin film strain gauge deposited on a glass substrate, is investigated in detail. Finite element analysis is used to model the expected sensor behavior. The substrate is shaped to exhibit a constant strain distribution, and is set up in a cantilever beam configuration. R. F. sputtering is used to deposit the Nichrome film, and the resistor pattern is transferred via photolithography. The gravitational force on a mass attached to the free end of the sensor …

Electron Beam Emission From A Ferroelectric Cathode, Crystal Briana Garland

Electrical & Computer Engineering Theses & Dissertations

The electron beam emission from a LTZ-2 (lead titanate-zirconate) ferroelectric cathode was characterized. The purpose was to determine the operation range for this type of electron emitter. The experimental apparatus consisted of a high voltage driving circuit with a charging voltage up to 30kV. A solid-state SCR switch is used to generate the high voltage pulse which induces a polarization change. Current densities on the order of 80A/cm² 30kV were achieved. The electron beam profile is Guassian. At long anode-cathode distances the measured current densities were found to be above Child-Langmuir space charge limits. The large current densities and …

Frequency Response Enhancement Of A Flow Sensor Using Diamond Thin Films Synthesized By Plasma Cvd, John Curren Hagwood

Electrical & Computer Engineering Theses & Dissertations

Theoretical modeling conducted previously in our Microelectronics Laboratory has shown that a layer of diamond film inserted between a metal film and a substrate will enhance the frequency response of a conventional thin film flow sensor. This thesis involved fabricating and testing a conventional thin film sensor of nickel on quartz (Ni/Q) and a diamond enhanced sensor (Ni/D/Q) for comparative frequency response analysis to validate the theory. Diamond films were grown onto quartz substrates using a microwave plasma enhanced chemical vapor deposition process. Conditions were established to synthesize continuous diamond films on quartz substrates. These films were characterized by scanning …

Fetal Heart Rate Detection With A Passive Acoustic Sensor System, Zongyao Zhou

Electrical & Computer Engineering Theses & Dissertations

Research and development is presented of real time signal processing methodologies for the detection of fetal heart tones from noise contaminated signals obtained from passive acoustic sensors. A nonlinear Teager energy operator is utilized for detection of the fetal heart tone event. Autocorrelation and a parallel redundancy correction algorithm derives fetal heart rates. A real time monitoring system is described which records and plots the time history of both the fetal heart rate and the acoustic fetal heart signal. The system is validated in the context of the fetal nonstress test. Comparisons are made with ultrasonic nonstress tests on a …

Transient Simulations And Modelling Of Semi-Insulating Gaas Photoconductive Switches, Prasun Kumar Raha

Electrical & Computer Engineering Theses & Dissertations

The primary objective of this thesis is to develop a one-dimensional transient simulator for Photoconductive Semiconductor Switches (PCSS) taking into consideration the material characteristics, the internal physical effects, and the external circuit. Simulations have been performed to study the device behavior at different voltage levels for copper-doped silicon-compensated GaAs material, though other materials could easily be simulated by changing the parameters. The model includes hole transport, and the results demonstrate the effect of hole injection, with and without recombination centers. In addition to developing a one-dimensional transient simulator, the role of various physical effects, such as the field-dependence of trapping …

Absorption Imaging Studies On Intrinsic Gaas, John Samuel Kenney

Electrical & Computer Engineering Theses & Dissertations

A diagnostic technique has been developed which allows recording of the temporal and spatial development of electric field structures in GaAs photoconductive switches. The optical method is based on the Franz-Keldysh effect. Measurements were performed with a Nd:YAG activation laser and a GaAs laser diode as the probe laser. At low applied voltages a 100 atm wide region of high electric field is seen at the cathode only. With increasing voltage strong domain like structures emerge at the anode also. A calibration measurement shows that the electric fields in these domains are well above 50 kV/cm. At a threshold voltage, …

Study Of Single-Fiber Fiber Optic Lever Microphone, Trung Duc Nguyen

Electrical & Computer Engineering Theses & Dissertations

Fiber optic sensors are widely used in today's technological applications, providing many advantages that conventional sensors lack. In particular, there is a demand in hypersonic applications to develop microphones to measure acoustic pressure that performs in high temperature and noisy surroundings. This thesis analyzes fiber optic lever microphones (FOLM), since they perform at high temperatures. An FOLM system is an intensity modulated sensor, which is simple to implement and is small in size. Two models of the FOLM have been fabricated and calibrated. The first model uses a seven-element fiber array while the second uses a single-fiber to transmit and …

The Effect Of Contacts On The Performance Of Electron-Beam Controlled Gaas And Diamond Switches, Michael Kevin Kennedy

Electrical & Computer Engineering Theses & Dissertations

The performance of GaAs and diamond as electron-beam controlled closing and opening switches has been studied. An emphasis has been placed on the effect of contacts on the current-voltage characteristics. The two materials studied were GaAs and diamond. Using the same semi-insulating GaAs wafer as a source of material, a bulk device and a p-i-n device have been fabricated and compared. The asymmetry of the pin diode allows operation at higher voltage because of the ability to suppress the lock-on effect. Whereas GaAs was ionized through cathodoluminescence; diamond, in the form of thin films, has been directly ionized by the …

The Breakdown Mechanism Of Hollow Cathode Discharge, Mai Tuyet Ngo

Electrical & Computer Engineering Theses & Dissertations

In a low pressure discharge, if the cathode incorporates a cylindrical or slit shaped hole, the discharge current can be several orders of magnitude higher than in one with plane parallel electrodes under the same pressure and voltage conditions. In this work hollow cathode discharges in Helium under the influence of variable parameters such as gas pressure, applied voltage, electrode gap spacing, external magnetic field, etc., are investigated by means of electrical and optical diagnostic techniques.

The results indicate that a hollow cathode discharge develops in two stages. The initial breakdown occurs along the longest straight path of the system, …

Monte Carlo Simulation Of Millimeter-Wave Gunn Effect Oscillators, Ramani Vaidyanathan

Electrical & Computer Engineering Theses & Dissertations

Monte Carlo simulations have been carried out to investigate the performance of microwave Gunn oscillators. Three separate aspects of the simulation problem have been comprehensively addressed in this work. First, the presence of an external circuit has been self-consistently incorporated into the calculations. The inclusion of the external circuit facilitates a study of the circuit controlled regime, and correctly models effects arising from the time dependent boundary conditions. Secondly, microscopic details of the electronic relaxation mechanisms which ultimately control the frequency response limits, have been taken into account through an iterative Monte Carlo-Poisson scheme. This procedure overcomes a potential shortcoming …

Measurement Of Thermal Noise In Condenser Microphones In A Vacuum-Isolation Vessel, Kim Chi Thi Ngo

Electrical & Computer Engineering Theses & Dissertations

The electrical noise generated by thermal agitation of the air molecules impinging upon the membrane of a condenser microphone and from its associated preamplifier has been studied analytically and experimentally over a wide bandwidth. These background noise levels constitute one of the most important specifications of a microphone for they determine the lowest sound pressure that can be detected. Therefore, a new method for measuring the thermal agitation noise within a bandwidth of 1-25600 Hz has been developed. The theoretical and experimental measurements of thermal agitation noise in a condenser microphone by enclosing the microphone in a vessel which is …

Deep Level Characterization Studies In Gaas, Gordhan R. Barevadia

Electrical & Computer Engineering Theses & Dissertations

The goal of this research was to investigate deep levels in different types of GaAs, a material for high power optically controlled bulk semiconductor switches. For low resistivity semiconductors, such as silicon doped GaAs material (p =0.054 Ω cm), deep level transient spectroscopy (DLTS) was used to characterize deep levels. Three deep levels (EL6, EL3, and EL2) have been detected in this material. For high resistivity semiconductors (p > 10⁴ Ω cm), difficulty of electrical carrier injection and of making a junction does not permit the use of DLTS technique. Therefore, an experimental set-up of the photo-induced current transient spectroscopy …

Analysis And Development Of A Switched Capacitor Power Supply, John Richard Hackworth

Electrical & Computer Engineering Theses & Dissertations

The combination of a switched capacitor network and switching power supply techniques can result in a transformer less regulated DC power supply that is small, relatively simple, and efficient. In addition, the output of such a system could be operated over a wide range of common mode voltages. Multiple switched capacitor supplies could be stacked to achieve voltage multiplication.

Although the output of a system of this type is a continuous function, the internal operation must be analyzed in finite time elements. This numerical analysis will be shown in both a mathematical approach and a computer model.

The Electrical Characteristics Of Semi-Insulating Gallium Arsenide A Material For High Power Switches, David Clifton Stoudt

Electrical & Computer Engineering Theses & Dissertations

An experimental study of the electrical characteristics of semi-insulating gallium arsenide has been performed. The goal of this research was to aid in the development of an electron-beam controlled high-power semiconductor switch. The electrical characteristics were found to be heavily dependent on the deep level configuration of the material being investigated. Two methods of deep level characterization are discussed and their results are compared to the information given by the material manufacturer. Studies were conducted to determine both the steady-state and transient dark current characteristics of the switch. Along with being a function of the applied voltage and the deep …

Model Of Hot-Film Sensor With Substrate Effects, David Mcalpine Judge

Electrical & Computer Engineering Theses & Dissertations

A detailed mathematical model is constructed to investigate the frequency response of a hot-film anemometer system. Since several diverse factors affect the frequency response, the analysis is broken down into three main parts. Each part is a detailed mathematical model. The first model consists of the ordinary differential equations which govern the electronics of the feedback system and heat transfer of the sensor. An important simplification in this model is that the rate of heat conduction from the sensor to its substrate is constant.

In the second model the unsteady state heat transfer properties of the substrate are examined by …

The Influence Of Transverse Magnetic Fields On The Current-Voltage Characteristics Of Glow Discharges, Thomas J. Powers

Electrical & Computer Engineering Theses & Dissertations

In low pressure discharges, operated in electronegative gas mixtures to the right of the Paschen curve minimum, the discharge resistance can be increased by application of transverse magnetic fields. In this range of operation, both the mean free path and the larmor radius are small compared to the discharge dimensions. The relationship between the electric field and the magnetic field is therefore controlled by electron- molecule collisional processes. Specifically, the magnetically induced increase in the discharge resistance is caused by a downward shift of the electron energy distribution which leads to an increase in attachment and a reduction in ionization. …

An Investigation Of Overvoltage Effects On A Gas-Blown Spark Gap, Michael Steven Mazzola

Electrical & Computer Engineering Theses & Dissertations

This experimental investigation addresses the anomalous overvoltage breakdown and subsequent recovery characteristics observed in gas-blown spark gaps. Previous investigations have reported a two-stage recovery process in self-break, pulse-charged, gas-blown spark gape in which the spark gap recovers first to an intermediate breakdown strength before recovering to the undisturbed breakdown voltage. The recovery process has been explained in terms of two different characteristic times. The first is that required to obtain initial recovery in which the spark gap regains its intrinsic breakdown strength. The second time is that required to obtain final recovery in which the pulse-charged spark gap regains the …

An Investigation To Improve Linear Predictive Vocoder Pulse/Noise Excitation Models, Elizabeth Annella Martina Effer

Electrical & Computer Engineering Theses & Dissertations

The quality of synthetic speech from Linear Predictive (LP) vocoders is known to be degraded due to the lack of detail in the commonly used pulse/noise excitation model. In this investigation, it was hypothesized that this degradation is due to the lack of precise timing information in the pulses and to the constraint that each short-time segment of excitation be either an impulse train or white noise. Accordingly, more complex excitation models were implemented using precise timing from peaks in the residual and a mixture of pulses and noise. Since the LP residual is known to be the perfect excitation …