Electrical and Electronics Commons^™

Optical Mode Pattern Study Of Gan Based Leds With And Without Nanoscale Top Grating, Gregory Chavoor

Electrical Engineering

This study analyzes optical confinement factor and light emitting mode order for three different GaN LEDs: a conventional LED, thin Film LED, and thin Film LED with a photonic crystal (PhC) grating. For the first structure, we increase the thickness of Al_xGa_1-xN from 0 to 600nm, alter the x composition in Al_xGa_1-xN from 0.05 to 0.2 in steps of 0.05, and adjust the p-GaN and n-GaN thicknesses each from 0 to 200nm. For the second structure, we alter the n-GaN substrate thickness from 300-1000nm in steps of 100nm and 1000-4000nm in steps …

Circular And Near-Circular Polarization States Of Evanescent Monochromatic Light Fields In Total Internal Reflection, R. M. A Azzam

Electrical Engineering Faculty Publications

Conditions for the production of near-circular polarization states of the evanescent field present in the rarer medium in total internal reflection of incident monochromatic p-polarized light at a dielectric-dielectric planar interface are determined. Such conditions are satisfied if high-index (>3.2) transparent prism materials (e.g., GaP and Ge) are used at angles of incidence well above the critical angle but sufficiently below grazing incidence. Furthermore, elliptical polarization of incident light with nonzero p and s components can be tailored to cause circular polarization of the resultant tangential electric field in the plane of the interface or circular polarization of the …

Poincaré Sphere Representation Of The Fixed-Polarizer Rotating-Retarder Optical System, R. M.A. Azzam

Electrical Engineering Faculty Publications

The trajectory of the polarization state of a monochromatic light beam after it passes through a fixed linear polarizer and a rotating linear retarder of arbitrary retardance Δ is determined on the Poincaré sphere. The three-dimensional figure-8 contour is shown to be the line of intersection of a right-circular cylinder with the sphere. The cylinder is parallel to the polar (s₃) axis, touches the sphere at the equator (at the point that represents the linear polarization transmitted by the fixed polarizer), and has a radius r=sin²(Δ/2). Projections of the trajectory in the coordinate planes of the …

Three-Dimensional Polarization States Of Monochromatic Light Fields, R. M.A. Azzam

Electrical Engineering Faculty Publications

The 3×1 generalized Jones vectors (GJVs) [ExEyEz]t (t indicates the transpose) that describe the linear, circular, and elliptical polarization states of an arbitrary three-dimensional (3-D) monochromatic light field are determined in terms of the geometrical parameters of the 3-D vibration of the time-harmonic electric field. In three dimensions, there are as many distinct linear polarization states as there are points on the surface of a hemisphere, and the number of distinct 3-D circular polarization states equals that of all two-dimensional (2-D) polarization states on the Poincaré sphere, of which only two are circular states. The subset of 3-D polarization …

Chaotic Bandgaps In Hybrid Acousto-Optic Feedback And Their Implications, Monish Ranjan Chatterjee, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

The nonlinear dynamics of a hybrid acousto-optic device was examined from the perspective of the Lyapunov exponent (LE) and bifurcation maps. The plots for LE versus system parameters and bifurcation maps have recently been examined against known simulation results including chaotic encryption experiments [1]. It is verified that the "loop gain" (feedback gain (β) times incident light amplitude (Iin) needs to be greater than one as a necessary , but not sufficient condition for the onset of chaos.

It is found that for certain combinations of β, Iin, net bias voltage (αtοt), and the initial value of the first-order scattered …

Simplified Design Of Thin-Film Polarizing Beam Splitter Using Embedded Symmetric Trilayer Stack, R. M.A. Azzam

Electrical Engineering Faculty Publications

An analytically tractable design procedure is presented for a polarizing beam splitter (PBS) that uses frustrated total internal reflection and optical tunneling by a symmetric LHL trilayer thin-film stack embedded in a high-index prism. Considerable simplification arises when the refractive index of the high-index center layer H matches the refractive index of the prism and its thickness is quarter-wave. This leads to a cube design in which zero reflection for the p polarization is achieved at a 45 degrees angle of incidence independent of the thicknesses of the identical symmetric low-index tunnel layers L and L. Arbitrarily high reflectance for …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Principal Angles And Principal Azimuths Of Frustrated Total Internal Reflection And Optical Tunneling By An Embedded Low-Index Thin Film, R. M.A. Azzam, F. F. Sudradjat

Electrical Engineering Faculty Publications

The condition for obtaining a differential (or ellipsometric) quarter-wave retardation when p- and s-polarized light of wavelength λ experience frustrated total internal reflection (FTIR) and optical tunneling at angles of incidence ϕ≥ the critical angle by a transparent thin film (medium 1) of low refractive index n1 and uniform thickness d, which is embedded in a transparent bulk medium 0 of high refractive index n0 takes the simple form: −tanh2x=tanδptanδs , in whichx=2πn1(d/λ)(N2sin2ϕ−1)1/2 , N=n0/n1 , and δp , δs are 01 interface Fresnel reflection phase shifts for the pand s polarizations. From this condition, the …

Examination Of Chaotic Signal Encryption And Recovery For Secure Communication Using Hybrid Acousto-Optic Feedback, Monish Ranjan Chatterjee, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

Generation of chaos from acousto-optic (A-O)Bragg cell modulators with an electronic feedback has been studied for over 3 decades. Since an acousto-optic Bragg cell with zeroth- and first-order feedback exhibits chaotic behavior past the threshold for bistability, such a system was recently examined for possible chaotic encryption of simple messages (such as a low-amplitude sinusoidal signal) applied via the bias input of the sound cell driver. Subsequent recovery of the message signal was carried out via a heterodyne-type strategy employing a locally generated chaotic carrier, with threshold parameters matched to the transmitting Bragg cell.

In this paper, we present numerical …

Scalar Em Beam Propagation In Inhomogeneous Media, John M. Jarem, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

In the previous chapter, we reviewed some of the mathematical preliminaries that will be useful later on in the text. In this chapter, we discuss some of the basic concepts of scalar wave propagation, and discuss an important numerical method, called the beam propagation method (BPM), to study propagation in linear media and in media with induced nonlinearities. Furthermore, we also discuss propagation through induced gratings, both transmission and reflection type, in order to assess energy coupling between participating waves. Finally, we introduce readers to an important characterization method, called the z-scan method, which is often used to determine the …

Binary And Core-Shell Nanoparticle Dispersed Liquid Crystal Cells For Metamaterial Applications, George Nehmetallah, Rola Aylo, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We theoretically explored the feasibility of a tunable metamaterial using binary as well as core-shell nanoparticle dispersed liquid crystal cells in the infrared and optical regimes. Owing to the spatial variation of the permittivity of the liquid crystal host upon the application of a bias voltage, the host was decomposed into a layered medium and the effective refractive index recalculated for each layer due to the distribution of polaritonic and plasmonic nanoparticles.

The scattering, extinction, and absorption of such a nanoparticle dispersed liquid crystal cell were also found. Depending on the applied voltage bias across the liquid crystal host, the …

Single-Beam Holographic Tomography Creates Images In Three Dimensions, George Nehmetallah, Partha P. Banerjee, Nickolai Kukhtarev

Electrical and Computer Engineering Faculty Publications

In digital holography (DH), the interference between light scattered from an object and a reference wave is recorded using a CCD camera. DH has various advantages over analog holography: no film processing is needed, reconstruction is performed using numerical methods, and no further experimental setup is necessary. However, one of the disadvantages of DH is that current CCDs have a resolution of approximately 1,000 lines/mm, which is less than that of photographic film.

Anisotropic Electrical Properties Of Nanostructured Metallic Thin Films, Mo Ahoujja, Piyush Shah, Andrew Saragan, Said Elhamri, Elena A. Guliants

Electrical and Computer Engineering Faculty Publications

High surface area, porous, metallic (Ti, Cr) nanorod thin ¯lms with columnar microstructure can be deposited using conventional physical vapor deposition technique of E-beam evaporation. The technique relies on the physical vapor deposition onto a static substrate oriented in a position where °ux from the source material (Ti, Cr) arrives at oblique angle. The adatoms provides geometrical shadowing which results in growth of nanorod columns in the direction of vapor source. Deposition conditions such as angle of the incoming vapor °ux, substrate temperature, surface di®usion etc. have strong in°uence on the shape and arrangement of the columnar thin ¯lms. In …

Multi-Pose Face Recognition And Tracking System, Binu Muraleedharan Nair, Jacob Foytik, Richard Tompkins, Yakov Diskin, Theus Aspiras, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

We propose a real time system for person detection, recognition and tracking using frontal and profile faces. The system integrates face detection, face recognition and tracking techniques. The face detection algorithm uses both frontal face and profile face detectors by extracting the 'Haar' features and uses them in a cascade of boosted classifiers. The pose is determined from the face detection algorithm which uses a combination of profile and frontal face cascades and, depending on the pose, the face is compared with a particular set of faces having the same range for classification. The detected faces are recognized by projecting …

Fluorinated Templates For Energy-Related Nanomaterials And Applications, Mohammed J. Meziani, Fushen Lu, Li Cao, Christopher E. Bunker, Elena A. Guliants, Ya-Ping Sun

Electrical and Computer Engineering Faculty Publications

Fluorinated ionomer membranes, as represented by the commercially available Nafion films, are macroscopically homogeneous and optically transparent but microscopically inhomogeneous with the presence of nanoscale hydrophilic cavities. These cavities serve as nanoscale reactors for the synthesis of nanoparticles from a variety of materials. The membranes with embedded nanoscale semiconductors, still optically transparent, have been used as sheet-photocatalysts for energy conversion applications, while those with embedded reactive metals used as nano-energetic materials for hydrogen generation and beyond. This chapter provides an overview on the templated synthesis of nanomaterials in fluorinated ionomer membranes and the various energy-related applications of this unique class …

Comparison Of Turbulence-Induced Scintillations For Multi-Wavelength Laser Beacons Over Tactical (7 Km) And Long (149 Km) Atmospheric Propagation Paths, Mikhail Vorontsov, Venkata S. Rao Gudimetla, Gary W. Carhart, Thomas Weyrauch, Svetlana Lachinova, Ernst Polnau, Joseph Rierson, Leonid A. Beresnev, Jony Jiang Liu, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We report results of the experimental analysis of atmospheric effects on laser beam propagation over two distinctive propagation paths: a long-range (149 km) propagation path between Mauna Loa (Island of Hawaii) and Haleakala (Island of Maui) mountains, and a tactical-range (7 km) propagation path between the roof of the Dayton Veterans Administration Medical Center (VAMC) and the Intelligent Optics Laboratory (IOL/UD) located on the 5th floor of the University of Dayton College Park Center building. Both testbeds include three laser beacons operating at wavelengths 532 nm, 1064 nm, and 1550 nm and a set of identical optical receiver systems with …

Doping Dependence Of Electronic And Mechanical Properties Of Gase1−XTeX And Ga1−XInXSe From First Principles, Zs. Rak, S. D. Mahanti, K. C. Mandal, N. C. Fernelius

Faculty Publications

No abstract provided.

Transmission Of P- And S-Polarized Light Through A Prism And The Condition Of Minimum Deviation, R. M.A. Azzam, Ryan M. Adams

Electrical Engineering Faculty Publications

The condition of minimum deviation (MD) by a transparent optically isotropic prism is re-derived, and expressions for the intensity transmittances Tp(θ) and Ts(θ) of an uncoated prism of refractive index n and prism angle α for incident p- ands-polarized light and their derivatives with respect to the internal angle of refraction θ are obtained. When the MD condition(θ=α/2) is satisfied, Ts is maximum and Tp is maximum or minimum. The transmission ellipsometric parametersψt,Δt of a symmetrically coated prism are also shown to be locally stationary with respect to θ at θ=α/2 . The constraint on (n,α) for …

Performance Measures In Acousto-Optic Chaotic Signal Encryption System Subject To Parametric Variations And Additive Noise, Monish Ranjan Chatterjee, Anjan K. Ghosh, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

Signal encryption and recovery using chaotic optical waves has been a subject of active research in the past 10 years. Since an acousto-optic Bragg cell with zeroth- and first-order feedback exhibits chaotic behavior past the threshold for bistability, such a system was recently examined for possible chaotic encryption using a low-amplitude sinusoidal signal applied via the bias input of the sound cell driver.

Subsequent recovery of the message signal was carried out via a heterodyne strategy employing a locally generated chaotic carrier, with threshold parameters matched to the transmitting Bragg cell. The simulation results, though encouraging, were limited to relatively …

Consideration Of Dispersion And Group Velocity Dispersion In The Determination Of Velocities Of Electromagnetic Propagation, Monish Ranjan Chatterjee, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

Electromagnetic (EM) propagation velocities play an important role in the determination of power and energy flow in materials and interfaces. It is well known that group and phase velocities need to be in opposition in order to achieve negative refractive index.

Recently, we have shown that considerable differences may exist in phase, group and signal/energy velocities for normal and anomalous dispersion, especially near dielectric resonances. This paper examines the phase and group velocities in the presence of normal and anomalous dispersion, and group velocity dispersion (GVD), which requires introduction of the second order coefficient in the permittivity and permeability models.

Coupling Into Waveguide Evanescent Modes With Applications In Electron Paramagnetic Resonance, Jason Walter Sidabras

Master's Theses (2009 -)

The use of analytical and numerical techniques in solving the coupling of evanescent modes in a microwave waveguide through slots can be optimized to create a uniform magnetic field excitation on axis within a waveguide. This work has direct applications in Electron Paramagnetic Resonance (EPR) where a 100~kHz time-varying magnetic field is incident on a sample contained in a microwave cavity. Typical cavity designs do not take into consideration the uniformity of the 100~kHz field modulation and assume it to be uniform enough over the sample region from quasi-static principles. This work shows otherwise and uses Ansoft (Pittsburgh, PA) High …

Monocular Passive Ranging By An Optical System With Band Pass Filtering, Joel R. Anderson

Theses and Dissertations

An instrument for monocular passive ranging based on atmospheric oxygen absorption near 762 nm has been designed, built and deployed to track emissive targets, including the plumes from jet engines or rockets. An intensified CCD array is coupled to variable band pass liquid crystal display filter and 3.5 – 8.8 degree field of view optics to observe the target. By recording sequential images at 7 Hz in three 6 nm width bands, the transmittance of the R-branch of the O₂ (X-b) (0,0) band is determined. A metric curve for determining range from transmittance is developed using the HITRAN spectral …

Electron Beam Lithography Throughput And Resolution Enhancement With Innovative Blanker Design, Junru Ruan

Legacy Theses & Dissertations (2009 - 2024)

Electron Beam Lithography (EBL) is one of the most important and most widely used methods for nano-fabrication. The primary advantage of electron beam lithography is its high resolution, and its ability to expose nanometer features without a mask. On the other hand, one of the key limitations of electron beam lithography is throughput. Slow blanking speed is one of the major bottlenecks for the system speed. In this dissertation, I will first review the prior literature of high speed blanking. Thorough theoretical and experimental studies are done on the existing designs. Physical models are built and analytical ray tracing is …

Harvesting Single Ferroelectric Domain Stressed Nanoparticles For Optical And Ferroic Applications, Gary Cook, J. L. Barnes, S. A. Basun, Dean R. Evans, Ron F. Ziolo, Arturo Ponce, Victor Yu. Reshetnyak, Anatoliy Glushchenko, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We describe techniques to selectively harvest single ferroelectric domain nanoparticles of BaTiO3 as small as 9 nm from a plethora of nanoparticles produced by mechanical grinding. High resolution transmission electron microscopy imaging shows the unidomain atomic structure of the nanoparticles and reveals compressive and tensile surface strains which are attributed to the preservation of ferroelectric behavior in these particles.

We demonstrate the positive benefits of using harvested nanoparticles in disparate liquid crystal systems.

Characterization Of Atmospheric Turbulence Effects Over 149 Km Propagation Path Using Multi-Wavelength Laser Beacons, Mikhail Vorontsov, Gary W. Carhart, Venkata S. Rao Gudimetla, Thomas Weyrauch, Eric Stevenson, Svetlana Lachinova, Leonid A. Beresnev, Jony Jiang Liu, Karl Rehder, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We describe preliminary results of a set of laser beam propagation experiments performed over a long (149 km) near-horizontal propagation path between Mauna Loa (Hawaii Island) and Haleakala (Island of Maui) mountains in February 2010. The distinctive feature of the experimental campaign referred to here as the Coherent Multi-Beam Atmospheric Transceiver (COMBAT) experiments is that the measurements of the atmospheric-turbulence induced laser beam intensity scintillations at the receiver telescope aperture were obtained simultaneously using three laser sources (laser beacons) with different wavelengths (λ1 = 0.53 μm, λ2 = 1.06 μm, and λ3 = 1.55 μm). The presented experimental results on …

Design Of Acousto-Optic Chaos Based Secure Free-Space Optical Communication Links, Anjan K. Ghosh, Pramode K. Verma, Samuel Cheng, Robert C. Huck, Monish Ranjan Chatterjee, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

We discuss the design of an acousto-optic cell based free space optical communication link where the data beam is made secure through chaos encryption. Using external signal modulation of the diffracted light from a hybrid acousto-optic cell chaos (or directly via incorporation in the sound-cell driver's bias voltage) encryption of data is possible. We have shown numerically that decryption of the encoded data is possible by using an identical acousto-optic system in the receiver.

Electron Multipactor: Theory Review, Comparison And Modeling Of Mitigation Techniques In Icepic, Neil G. Rogers

Theses and Dissertations

Mitigation approaches for single surface multipactor at dielectric windows are investigated using Particle-In-Cell (PIC) simulations. Initially baseline susceptibility diagrams are constructed analytically and compared with self-consistent, dynamic system trajectories. The power deposited on the surface of a dielectric window in an HPM system is considered using three different methods and the results of PIC simulations. Geometric mitigation is then considered by varying the window orientation with respect to the HPM electric held. Small angular deviations, less than 20 degrees, from the nominal case of normal incidence show dramatic changes in the susceptibility diagram. A materials approach to mitigation is then …

Tilted Parallel Dielectric Slab As A Multilevel Attenuator For Incident P- Or S-Polarized Light, R. M.A. Azzam

Electrical Engineering Faculty Publications

Under the condition of first-order blooming, a parallel dielectric slab, which is inserted in the path of an obliquely incident p- or s-polarized light beam, introduces multiple discrete attenuation levels given by 1/3, 4/27, 4/243,...... in reflection and 4/9, 4/81, 4/729,...... in transmission. These attenuation levels are independent of the slab refractive index, incident p or s linear polarization, or the presence of identical transparent surface coatings at the front and back sides of the slab. Therefore, the tilted slab provides multidecade reflectance and attenuation reference values that can be used in calibrating spectrophotometers and filters, and also …

Monoclinic Optical Constants, Birefringence, And Dichroism Of Slanted Titanium Nanocolumns Determined By Generalized Ellipsometry, Daniel Schmidt, Benjamin Booso, Tino Hofmann, Eva Schubert, Andrew Sarangan, Mathias Schubert

Electrical and Computer Engineering Faculty Publications

Generalized spectroscopic ellipsometry determines the principal monoclinic optical constants of thin films consisting of slanted titanium nanocolumns deposited by glancing angle deposition under 85° incidence and tilted from the surface normal by 47°. Form birefringence measured for wavelengths from 500 to 1000 nm renders the Ti nanocolumns monoclinic absorbing crystals with c-axis along the nanocolumns, b-axis parallel to the film interface, and 67.5° monoclinic angle between the aand c-axes. The columnar thin film reveals anomalous optical dispersion, extreme birefringence, strong dichroism, and differs completely from bulk titanium. Characteristic bulk interband transitions are absent in the spectral range investigated.

Plurality Of Principal Angles For A Given Pseudo-Brewster Angle When Polarized Light Is Reflected At A Dielectric-Conductor Interface, R. M.A. Azzam, A. Alsamman

Electrical Engineering Faculty Publications

The pseudo-Brewster angle ϕpB of minimum reflectance for p-polarized light and the principal angle ϕ¯ at which incident linearly polarized light of the proper azimuth is reflected circularly polarized are considered as functions of the complex relative dielectric function ε of a dielectric–conductor interface over the entire complex ε plane. In particular, the spread of ϕ¯for a given ϕpB is determined, and the maximum difference (ϕ¯−ϕpB)max is obtained as a function of ϕpB . The maximum difference (ϕ¯−ϕpB)max approaches 45° and 0 in the limit as ϕpB→0 and 90°, respectively. ForϕpB<22.666° , multiple principal angles ϕ¯i , i=1,2,3 , appear for each ε in a subdomain of fractional optical constants. …