Electrical and Electronics Commons^™

An Experimental Approach Towards Pv-Based Solar System Sizing For An Engineering Laboratory, Muyideen O. Lawal

Tanzania Journal of Engineering and Technology (TJET)

This study aims at providing an experimental sizing procedure for a rooftop PV-based solar power system for an engineering laboratory. This was achieved by monitoring the peak power and energy delivered by an installed 20W solar panel into an 18 Ah battery. Knowledge of the average daily peak power and energy was used to determine the percentage rated capacity available for use and the sun hour. A load consumption comparison was also carried out with and without the connection of a load to inverter. In addition to this, the monitoring of the no-load consumption of the inverter was carried out. …

Renewable Energy Microgrids To Improve Electrification Rate In Democratic Republic Of Congo: Case Of Hydro, Municipal Waste And Solar, Ngondo Otshwe Josue, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, it is imperative for citizens to have access to electricity. This applies to Congolese--rural and urban dwellers, and if possible, it should be guaranteed by government’s laws and policies. Howev er, the rural and urban areas of Democratic Republic of Congo (DRC) suffer majorly from lack of access to electricity. The major reasons are the high costs associated with connection to the national central grid and production insufficiency. Therefore, one feasible approach to electrify these areas is to use microgrids. This technolo gy is decent and viable option for energy revolution since it incorpo rates energy storage systems, distributed …

Viability Analysis Of Ubungo Ii Gas Power Plant Efficiency Improvement Using Co-Generation System, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

The power utility, Tanzania Electric Supply Company Limited (TANESCO) is faced with challenges of supplying adequate power to the ever-increasing demand. To this end, this paper explores the installed Ubungo Gas Power Plant (UGP II) located in Dar es Salaam to find means of utilizing it in co-generation method. The study embarked on detailed modelling of the system and run simulations which indicated that the co-generation can result to power generation efficiency increase between 10.42 to 50.92%. It is recommended to change the UGP II to exploit this co-generation method. Further, the study could be improved by including more parameters …

Sunsation’S Solar Powered Picnic Table, Michelle M. Barnett, Christopher Barber, Casey Durham, David Mason

Mechanical Engineering

Team SunSation is an interdisciplinary senior design project group that was tasked with developing a semi-permanent seating area for Cal Poly's electrical engineering courtyard. The EE courtyard is populated with plastic folding tables and chairs that are slowly falling apart. Dale Dolan, the head of the EE department, requested that a table design be developed that incorporates the use of solar panels. The addition of the solar panels to the table would help promote clean renewable energy as well as provide shade to those sitting in the courtyard.

The solution that SunSation arrived at is broken up into mechanical/structural, electrical, …

8 Dof Quadrupedal Hopping Robot, Clayton T. Elwell, John Bennett, Tyler Mccue, Daniel Munic

Mechanical Engineering

The goal of our senior project was to fabricate an eight degree of freedom (DOF) prototypical quadrupedal robot, develop a controller than commands the quadruped to repeatedly jump 10 cm in the air, and fabricate a modular test stand to safely deploy our controller on the quadruped. The creation of a functional quadruped will bring attention to Dr. Siyuan Xing and Charlie Refvem’s research group, Cal Poly Legged Robots, and will give future Cal Poly undergraduate and graduate students a learning tool to explore dynamic control of biomimetic robotic systems.

Over the course of our senior project, we successfully manufactured …

Multifamily Complex Smart Locks For Property Management And Tenant Security, April Mills, Allen Chen, Dana Kumamoto, Michael Cook

Mechanical Engineering

Maintaining and managing hundreds of locks and physical keys for an apartment complex can be time consuming and costly, especially when the apartments turn over to new tenants. Our goal was to develop a smart door lock that is compatible with Obodo’s management app for apartment complexes to make accessing apartments secure and simpler for tenants and easier to manage for owners.

We designed and manufactured one smart door lock that is powered with four AA batteries and utilizes a dynamic NFC device and Bluetooth technology. The board can enter a sleep mode which reduces power consumption. The dynamic NFC …

Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini

Theses and Dissertations

Dynamic testing provides valuable insight into the behavior of materials undergoing fast deformation. During Split-Hopkinson Pressure Bar testing, stress waves are measured using strain gauges as voltage variations that are usually very small. Therefore, an amplifier is required to amplify the data and analyze it. One of the few available amplifiers designed for this purpose is provided by Vishay Micro-Measurements which limits the user’s options when it comes to research or industry. Among the challenges of implementing the Hopkinson technology in the industry are the size and cost of the amplifier. In this work, we propose a novel design of …

Automated Robotic Light Bulb Testing Platform, Agha I. Akram, Muhammad Ali Ummy

Publications and Research

The main purpose of this project is to create a functional prototype of a multilayered system that incorporates aspects of electrical, mechanical, and computer engineering technology. The main objective of the system is to be able to determine whether a light bulb is working or not. The building blocks of this system are a robotic arm that is able to slide along a rail (for added mobility), a conveyor belt, and an electromechanical device that holds and tests light bulbs. Initially, the robot arm picks up a light bulb and places it into the holder which then tests it. A …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Autonomous Navigator Mobile Robot Upgrade, David Sansoucy

Thinking Matters Symposium

The mobile robot platform has been developed over the course of 10 years at USM. In Spring 2020, Belle-Isle and Werner updated the previous framework by rewriting the software to use the ROS framework running on an on-board Raspberry Pi 3. They also implemented navigation using an A* motion planning algorithm and image processing. In Summer 2021, Ames incorporated Lidar and Kinect sensors onto the robot to improve its real-time navigation capabilities. He also made improvements to the power distribution systems. This project aimed to build on the ROS frameworks developed by the previous 2 teams with the main goal …

Dc Microgrid Fault Detection Using Multiresolution Analysis Of Traveling Waves, Rudy Montoya

Mechanical Engineering ETDs

Fast detection and isolation of faults in a DC microgrid is of particular importance. Fast tripping protection (i) increases the lifetime of power electronics (PE) switches by avoiding high fault current magnitudes and (ii) enhances the controllability of PE converters. This thesis proposes a traveling wave (TW) based scheme for fast tripping protection of DC microgrids. The proposed scheme utilizes a discrete wavelet transform (DWT) to calculate the high-frequency components of DC fault currents. Multiresolution analysis (MRA) using DWT is utilized to detect TW components for different frequency ranges. The Parseval energy calculated from the MRA coefficients are then used …

Real-Time Complex Hand Gestures Recognition Based On Multi- Dimensional Features, Isack Bulugu

Tanzania Journal of Engineering and Technology (TJET)

Gesture recognition is broadly utilized within the field of sensing. There are basically three gesture recognition methods based on computer vision, depth sensor and motion sensor. Motion sensor-based gesture recognition has few input data, fast speed, and direct access to three- dimensional information of the hand. The advantages of traditional motion sensor-based gesture recognition have gradually become a current research hotspot. The essence of traditional motion sensor-based gesture recognition is a pattern recognition problem, and its accuracy depends heavily on the feature dataset extracted from prior experience. Unlike traditional pattern recognition methods, deep learning can be used to a large …

Complete Neighbourhood Search Heuristic Algorithm For Portfolio Optimization, Collether John

Tanzania Journal of Engineering and Technology (TJET)

In portfolio optimization, the fundamental goal of an investor is to optimally allocate investments between different assets. Mean-variance optimization methods make unrealistic assumptions to solve the problem of optimal allocation. On the other hand, when realistic constraints like holding size and cardinality are introduced it leads to optimal asset allocation which differ from the mean variance optimization. The resulting optimization problem become quite complex as it exhibits multiple local extrema and discontinuities. Heuristic algorithms work well for the complex problem. Therefore, a heuristic algorithm is developed which is based on hill climbing complete (HC-C). It is utilized to solve the …

Economic Analysis Of Islanded Microgrid: A Case Study Of Kisiju Village - Coastal Region, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

The concept of Microgrid (MG) has gained significant attention of researchers and projects on the business side of electrical power generation and utilization, particularly in electrification of islanded areas such as villages. Most of these microgrids are powered by renewable energy resources (RERs) and they distribute power in low voltage distribution networks. Hence, these systems are faced with reliability problems due to the intermittency nature of RERs which affect the technical as well as the return on Investment of specific projects. In the latter context, reliability and economic analysis of the MG systems is an inevitable choice. This paper presents …

Assembly Of Alumina Particles In Aqueous Suspensions Induced By High‐Frequency Ac Electric Field, James E. John, Shizhi Qian, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

The role of high-frequency alternating current (AC) electric field in the assembly of alumina particles in aqueous media was investigated. Field–particle interactions were in situ investigated for coarse and fine powder particles in very dilute suspensions. For both coarse and fine particles, AC field-induced assembly led to the formation of chains of particles within a minute, which were aligned in the field direction. However, a much finer network of particle chains evolved in fine particle suspensions. Threshold field strength for chain formation was also lower for fine particles (28 V/mm) than for coarse particles (50 V/mm), suggesting stronger interactions for …

Laptop Recycling Case Study: Estimating The Contained Value And Value Recovery Process Feasibility Of End-Of-Life Consumer Electronics, Zebulon Hart

Theses and Dissertations--Mining Engineering

Work has been done to establish, through the development and use of novel assay techniques and analysis metrics, the contained value of a sampling of laptop computers (as an analog for myriad e-waste sources). This work has conceptualized e-waste as an alternative to geologic-origin complex metallic ores and has likewise evaluated the feasibility of value recovery from e-waste sources in a similar manner to an ore. The application of conventional and novel mineral separation techniques to e-waste recycling processes has been evaluated and positive results are demonstrated. Further, this work has demonstrated the ability to identify the presence of base …

Spray Deposition Of Sustainable Plant Based Graphene In Thermosetting Carbon Fiber Laminates For Mechanical, Thermal, And Electrical Properties, Daniel W. Mulqueen, Siavash Sattar, Thienan Le, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Graphene has generated substantial interest as a filler due to its exceptional strength, flexibility, and conductivity but faces obstacles in supply and implementation. A renewable, plant-based graphene nanoparticle (pGNP) presents a more accessible filler with the same properties as mineral graphenes. In this study, we examine the effects of pGNP, which was sprayed on a carbon fiber/epoxy prepreg at loadings from 1.1 to 4.2 g/m². The study considered the mechanical, thermal, and electrical properties of pGNP-composite. An even particle dispersion was achieved using a spray application of pGNP in a water/alcohol suspension with the addition of surfactants and …

Chemical Clean Automated Loader, Jordyn Bryner

Williams Honors College, Honors Research Projects

TTM Technologies (TTM) is a global printed circuit board (PCB) manufacturer. The work described in this report was completed in the TTM North Jackson, Ohio location. This plant focuses primarily on the manufacturing of rigid and rigid-flex PCBs for the aerospace and defense industry. TTM North Jackson has an ongoing labor dependency issue due to the shortage of workers the nation is facing. To solve this problem, TTM has focused the efforts of their new engineers and interns on automating processes that are labor dependent. The goal is to provide design guidance to be used later by TTM to automate …

High Energy And Power Density Peptidoglycan Musclesthrough Super-Viscous Nanoconfined Water, Haozhen Wang, Zhi-Lun Liu, Jianpei Lao, Sheng Zhang, Rinat Abzalimov, Tong Wang, Xi Chen

Advanced Science Research Center

Water-responsive (WR) materials that reversibly deform in response to humidity changes show great potential for developing muscle-like actuators for miniature and biomimetic robotics. Here, it is presented that Bacillus (B.) subtilis’ peptidoglycan (PG) exhibits WR actuation energy and power densities reaching 72.6 MJ m−3 and 9.1 MW m−3, respectively, orders of magnitude higher than those of frequently used actuators, such as piezoelectric actuators and dielectric elastomers. PG can deform as much as 27.2% within 110 ms, and its actuation pressure reaches ≈354.6 MPa. Surprisingly, PG exhibits an energy conversion efficiency of ≈66.8%, which can be attributed to its super-viscous nanoconfined …

Printed Circuit Board Design And Layout For Hobbyists, Engineers, And Students, Michael A. Derrenbacher

Master's Theses

Printed Circuit Boards (PCBs) are a ubiquitous element of virtually every electronic system manufactured world-wide. It is not a stretch of the imagination to say that if it’s electronic, there is a PCB in it. PCBs are necessary tools for electronics work, and tools need to have instructions. For better or worse, PCB knowledge is a deep and wide ocean. There is much to cover for even a surface level understanding, and there are deep areas rich in technical expertise. Navigating the ocean of knowledge is treacherous; common knowledge of yore can be downright dubious now. PCB manufacturing and electronics …

Additive Manufacturing Using Robotic Manipulators, Fdm, And Aerosol Jet Printers., Alexander Curry

Electronic Theses and Dissertations

Additive manufacturing has created countless new opportunities for fabrication of devices in the past few years. Advances in additive manufacturing continue to change the way that many devices are fabricated by simplifying processes and often lowering cost. Fused deposition modeling (FDM) is the most common form of 3D printing. It is a well-developed process that can print various plastic materials into three-dimensional structures. This technology is used in a lot of industries for rapid prototyping and sometimes small batch manufacturing. It is very inexpensive, and a prototype can be created in a few hours, rather than days. This is useful …

Synthesis And Characterization Of Tin (Sn) Incorporated Ga2o3, Guillermo Nicolas Gutierrez

Open Access Theses & Dissertations

In this work, we report on the synthesis, characterization of tin (Sn) incorporated gallium oxide Ga2O3 compounds, also included in this work is the effect of tin concentration related to the optical and electrochemical properties. The Sn incorporation into Ga2O3 creates a significant reduction in the bandgap and causes a nonlinear optical activity as the concentration varies. Substantial investigation performed to the structure, phase, and morphology of the mixed compounds governed by the stoichiometry equation Ga2−2xSnxO3-ɗ indicates that the Sn incorporation from 0.00 ≤ x ≤ 0.30 has a significant effect on these properties. To synthesize the Ga-Sn-O compounds a …

Combined Devices Of Facts Technology, Bahrom Ravshanovich Normuratov Associate Lecturer, Misrikhan Misrikhanov, Shukhrat Khamidov

Technical science and innovation

FACTS - Flexible Alternative Current Transmission System technology is a family of devices, each of which can be used individually and in concert with other devices to control the interrelated parameters of the electrical power system. The mission of FACTS technology is to improve the control of power flows in both steady-state and transient modes of EPS. Flexibility of Electric Power Transmission, applied as "The ability to adapt to changes in transmission system or operating conditions while maintaining sufficient operating limits in steady-state and transient modes". Controlled Flexible AC Transmission Lines - Flexibility from Electric Power Transmission means "AC Power …

Comparison Of Concrete And Steel Jacket Methods For Reinforcing A Concrete Bridge Pier By Numerical And Experimental Studies, Hadi Faghihmaleki

Makara Journal of Technology

Various rehabilitation and strengthening procedures have been developed in recent decades. A study to determine which methods can be implemented to increase the useful life of the bridge before strengthening must be performed. In this study, the seismic behavior of a reinforced concrete bridge pier with dimension 3.5 × 3.5 m, which was reinforced by two steel and a concrete jacket, was investigated. Nonlinear geometric models and materials were analyzed to estimate the seismic parameters of the pier. Results show an increase in energy absorption, ultimate strength, and ductility for the steel jacket, as well as a greater increase in …

Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang

Makara Journal of Technology

X-ray diffraction techniques were performed to determine the actual crystal structure of A2 austenitic stainless steel (ASS) as-cast and A2 ASS after arc plasma sintering (APS) for 2 s. Computations were conducted on the basis of the Bragg arithmetic formula by comparing the S2 arithmetic with the interplanar spacing. The Bragg arithmetic formula is a simple series for the determination of the crystalline phase of materials based on the Miller indices of cubic shapes or other shapes. A2 ASS as-cast was identified to have a crystal structure of face-centered cubic with lattice parameter a = 3.58 Å. A similar crystal …

Trend Significance Levels Of Rain Onset And Cessation And Lengths Of The Wet And Dry Seasons In Epe, Lagos State, Nigeria, Adekunle Adedeji Alli, Olorunwa Eric Omofunmi

Makara Journal of Technology

This study aims to reduce crop failure resulting from a dry spell, which is the first occurrence of unsustainable rainfall that deceives farmers into planting. Thus, trends need to be tested using hypothesis, kurtosis, and other statistics to analyze the risks associated with unstable planting calendars and their possible mitigation strategies. The daily rainfall data from 1982 to 2018 were obtained from the archive of NASA/POWER SRB/FLASH, and the research location is Epe, Lagos State, Nigeria, which lies at latitude 6.585° N and longitude 3.962° E. Microsoft Excel was used to perform the tests. Results show that the null hypothesis …

Kinetic Modeling Study Of Laminar Burning Velocity Of Gasoline–Ethanol–Methanol Blends At Elevated Temperature And Pressure, Ahmad Syihan Auzani, Cahyo Setyo Wibowo, Riesta Anggarani, Yulianto Sulistyo Nugroho, Bambang Sugiarto

Makara Journal of Technology

Gasoline–ethanol–methanol (GEM) blends have been considered to replace pure gasoline as spark ignition engine fuel. Their physical and chemical properties and performance and emission measurements from real engines have been reported previously. However, a fundamental study that can explain the unique results of GEM compared with those of pure gasoline is lacking. This study aims to compare the laminar burning velocity of GEM blends at different mixtures, equivalence ratios, temperatures, and pressures with that of pure gasoline. A laminar flame propagation model and reaction mechanisms from the literature were were for a numerical simulation. In this study, the chemical components …

Improvement Of Electrical Properties Of Cmc-Pva Doped With Various Contents Of Lino3 As An Application For Hybrid Polymer Electrolytes, Amalia Zulkifli, Norfatihah Mazuki, Ahmad Salihin Samsudin

Makara Journal of Technology

The present work was carried out with the development of hybrid polymer electrolytes (HPEs) by using carboxymethyl cellulose (CMC)–polyvinyl alcohol (PVA) doped with different contents of lithium nitrate (LiNO3) for the determination of their structural and conduction properties. The structural analysis was conducted by using Fourier transform infra-red spectroscopy and showed the interaction between the blend host polymer and ionic dopant, which formed via the coordinating site of CMC-PVA and Li+-NO3−. The complexes of CMC-PVA doped LiNO3 led to an increment in ionic conductivity, as observed by electrical impedance spectroscopy, and the sample containing 20 wt% LiNO3 obtained the highest …

Music Information Retrieval Based On Active Frequency, Hardianto Wibowo, Wildan Suharso, Yufis Azhar, Galih Wasis Wicaksono, Agus Eko Minarno, Dani Harmanto

Makara Journal of Technology

Music is the art of combining frequencies. A balance of frequencies gives rise to a harmonious tone. Several features of music can be analyzed, and they include sociocultural background, lyrics, mood, tempo, rhythm, harmony, melody, timbre, and instrumentation. In this study, we use the frequency of instrumentation as a feature for classification because each instrument has a frequency range. To test this frequency range, we use five music genres and one music playing skill. The five genres are dangdut, electronic dance music (EDM), metal, pop/rock, and reggae. The music playing skill is acoustic. Active frequencies are tested using the k-nearest …