Electrical and Electronics Commons^™

Embedding A Grid Of Load Cells Into A Dining Table For Automatic Monitoring And Detection Of Eating Events, Mohammad Mayyan

All Dissertations

This dissertation describes a “smart dining table” that can detect and measure consumption events. This work is motivated by the growing problem of obesity, which is a global problem and an epidemic in the United States and Europe. Chapter 1 gives a background on the economic burden of obesity and its comorbidities. For the assessment of obesity, we briefly describe the classic dietary assessment tools and discuss their drawback and the necessity of using more objective, accurate, low-cost, and in-situ automatic dietary assessment tools. We explain in short various technologies used for automatic dietary assessment such as acoustic-, motion-, or …

Miniaturized Battery Powered Air Quality Monitoring System, Bryan Chacon

All Theses

In this work, an air quality monitoring system was developed using various sensors that measure specific air quality parameters, including Volatile Organic Compounds, Carbon Dioxide, particulate matter of varying sizes, ambient pressure, humidity, and temperature. This system is based off a Particle micro-controller, Boron LTE CAT-M1 which allows for cellular connectivity for real-time data transmission. It is powered by a 3.7 Volt Li-Po battery and has a miniaturized design which allows for portability. This data is processed through an Internet of Things software provider that allows for the device to be connected and accessed to and from anywhere in the …

Improving The Performance And Evaluation Of Computer-Assisted Semen Analysis, Ji-Won Choi

Dissertations

Semen analysis is performed routinely in fertility clinics to analyze the quality of semen and sperm cells of male patients. The analysis is typically performed by trained technicians or by Computer-Assisted Semen Analysis (CASA) systems. Manual semen analysis performed by technicians is subjective, time-consuming, and laborious, and yet most fertility clinics perform semen analysis in this manner. CASA systems, which are designed to perform the same tasks automatically, have a considerable market share, yet many studies still express concerns about their accuracy and consistency. In this dissertation, the focus is on detection, tracking, and classification of sperm cells in semen …

Insole Fall Prevention Device, Nick M. Hughes, Andrew M. Slaboda

Biomedical Engineering

Falls among the aging population occur every single day, with 1 in every 5 resulting in some injury and 300,000 hospitalized every year with a hip fracture [1]. The most popular and effective way to mitigate these falls is through physical therapist intervention. However, with the increased popularity in telerehab, many patients at risk for falls cannot accurately convey their gait tendencies to their physical therapists from the comfort of their home or while not in direct contact with the PT. A device like an insole, implanted with force sensors, which measures different parts of a patient’s foot, could convey …

Novel Platforms For Large-Scale Adherent Culture Of Mammalian Cells, Ashkan Yekrangsafakar

LSU Doctoral Dissertations

With recent advances in biotechnology, there is a strong and urgent need for robust platforms to culture mammalian cells on a large scale to produce biopharmaceuticals. To this end, various bioreactors have been developed over the past decades, but their capacity and efficiency are often limited by insufficient mass transfer rate and excessive shear stress. In this work, multiple novel bioreactors for the large-scale adherent culture of anchorage-dependent cells were developed.

Hollow MicroCarriers (HMC) was developed as an alternative solution for the microcarrier-based culture system in a stirred-tank bioreactor. In the conventional microcarrier technique, cells are exposed to the harmful …

Integration Of Electrical Impedance Spectroscopy For Multichannel Cell Culture Measurement, Conard Chan

Master's Theses

ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY (EIS) has been widely used to study the electrical properties of biological material due to its non-invasive nature and experimental reliability. However, most of the precision impedance analyzers used in EIS only provide single- or two-channel measurements which are inadequate for larger-scale multiplexed measurements, such as those found in modern microfluidic cell culture experiments. The Biomedical Microsystems Laboratory has developed a 16-channel cell culture platform with integrated electrode arrays for monitoring cell growth and electrical properties (i.e., the so-called “electrical phenotype”). In this paper, a system consisting of a 16-channel solid-state analog multiplexer (MUX)paired with a low-cost, …

The Design Of Cmos Front-End Amplifiers For Electrical Impedance Applications, Yueh-Ching Teng

Dartmouth College Ph.D Dissertations

Electrical Impedance Tomography (EIT) is a medical imaging methodology that does not need any kind of ionizing radiation. It is significantly cheaper and smaller than Computerized Tomography (CT) or Magnetic Resonance Imaging (MRI). These advantages make EIT particularly suitable for emerging applications like the continuous medical imaging and telemonitoring of organ function. Current bench-top EIT systems are bulky and require shielded cables to interface with measurement electrodes. The cable introduces parasitic capacitances which shunt the desired signals and degrade the accuracy of the measurements. A EIT system based on application-specific integrated circuits (ASICs) can reduce the parasitic and stray capacitance …

Non-Invasive In-Vitro Glucose Monitoring Using Optical Sensor And Machine Learning Techniques For Diabetes Applications, Maryamsadat Shokrekhodaei

Open Access Theses & Dissertations

Diabetes is a major public health challenge affecting more than 451 million people. Physiological and experimental factors influence the accuracy of non-invasive glucose monitoring, and these need to be addressed before replacing the finger prick method with a non-invasive glucose measurement technique. Also, the suitable employment of machine learning techniques on experimental data can significantly improve the accuracy of glucose predictions.

This work includes the design, development, testing and data analysis of an optical based sensor for glucose measurements. The feasibility of non-invasive measurement of glucose within aqueous solutions that assimilate the composition of human blood plasma is investigated. The …

Experimental And Analysis Of Electromagnetic Characterization Of Biological And Non-Biological Materials In Microwave, Millimeter-Wave, And Terahertz Frequency Bands, Nagma Vohra

Graduate Theses and Dissertations

The goal of this research is to characterize the electromagnetic properties of biological and non-biological materials at terahertz (THz), millimeter-wave, and microwave frequency bands. The biological specimens are measured using the THz imaging and spectroscopy system, whereas the non-biological materials are measured using the microwave and millimeter-wave free-space system. These facilities are located in the Engineering Research Center at the University of Arkansas. The THz imaging system (TPS 3000) uses a Ti-Sapphire laser directed on the photoconductive antennas to generate a THz time domain pulse. Upon using the Fourier Transform, the spectrum of the pulsed THz signal includes frequencies from …

Portable Ventilator, Bradley C. Weeks, Jack W. Brewer, Sanders Sanabria

Electrical Engineering

The current COVID-19 pandemic has heavily impacted the healthcare system in the United States and elsewhere. The need for patients to have access to a hospital with a ventilator along with a shortage of ventilators for recovery and at-home care as a result of minimal hospital vacancy for patients has been greatly stressed. The presented problem is both an unmet demand and supply of portable and effective ventilators. Existing ventilators have many shortcomings that should be addressed: size, weight, cost, and complexity of current ventilators confines users to stay in a medical facility whilst being monitored by professionals. This both …

Error Prevention In Sensors And Sensor Systems, Pedro J. Chacon Dominguez

LSU Doctoral Dissertations

Achievements in all fields of engineering and fabrication methods have led towards optimization and integration of multiple sensing devices into a concise system. These advances have caused significant innovation in various commercial, industrial, and research efforts. Integrations of subsystems have important applications for sensor systems in particular. The need for reporting and real time awareness of a device’s condition and surroundings have led to sensor systems being implemented in a wide variety of fields. From environmental sensors for agriculture, to object characterization and biomedical sensing, the application for sensor systems has impacted all modern facets of innovation. With these innovations, …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Smart Motor Syringe System, Conard Chan, Jenny Chiao

Electrical Engineering

Syringe pumps are widely used in many research applications especially in the applications that need precise control. Today most medical research utilizes syringes to control the fluid being pumped to the experiment objects. In most cases microscopic or nano-scopic motion control is required to acquire optimal results, such application includes purification of DNA/RNA from contaminants[1]. The high precision required to control the syringe pump makes it difficult to perform manually. This paper focuses on the design of an intelligent syringe pump motor control system to achieve reliable and precise control for biomedical experiments. This project improves medical research quality with …

Telemedicine: An Iot Based Remote Healthcare System., Mohammad Abdellatif, Walaa Mohamed

Electrical Engineering

This paper proposes a remote healthcare system which is referred to as Telemedicine. Telemedicine is a platform that establishes a connection be-tween the patient and the doctor. This platform belongs to the internet of medical things (IoMT) by enabling multiple medical sensors to connect to a server either using multiple communication technologies such as Wi-Fi, Bluetooth or GSM technologies. The system collects data from several sensors and sends them using one of the aforementioned technologies using an Arduino Board, while the inter-face is made with matlab and C#. Additionally, a comparative study between the three communications technologies used to connect …

Quadrupoles For Remote Electrostimulation Incorporating Bipolar Cancellation, Shu Xiao, Ryo Yamada, Carol Zhou

Bioelectrics Publications

Introduction: A method that utilizes nanosecond bipolar cancellation (BPC) near a quadrupole electrodes to suppress a biological response but cancels the distal BPC at the quadrupole center, i.e., cancellation of cancellation (CANCAN), may allow for a remote focused stimulation at the quadrupole center.

Objectives: The primary object of this study was to outline the requirement of the CANCAN implementation and select an effective quadrupole configuration.

Results: We have studied three quadrupole electrode configurations, a rod quadrupole, a plate quadrupole (Plate-Q), and a resistor quadrupole. The pulse shapes of electric fields include monophasic pulses, cancellation pulses, and additive pulses. The Plate-Q …

Early Detection Of Asthma Via Enhanced Resolution Of Small Airways Using Ultra-Low Frequency Impulse Oscillometry, Christopher M. Aguilar

Open Access Theses & Dissertations

Examination of lung function for diagnosis and monitoring of diseases such as chronic obstructive pulmonary disease (COPD) and asthma can be performed with a variety of pulmonary function testing (PFT) techniques. The most commonly prescribed of these procedures are spirometry and whole-body plethysmography. However, these active participation tests depend on forced breathing maneuvers, may be physically exhausting, might not produce enough information, and are susceptible to being subject-dependent. In contrast, passive PFT approaches such as the forced oscillation technique (FOT) and the impulse oscillometry system (IOS) are increasingly being utilized for measuring lung mechanics because they require only minimal participation, …

Design, Construction, And Characterization Of A Combined Mini-Co₂/Voc Sensor And Gas Chromatograph For Field Research, Rishi Basdeo, Michael Hampton

Digital Repository: Showcase of Undergraduate Research Excellence

No abstract provided.

Indocyanine-Green-Assisted Near-Infrared Dental Fluorescence Imaging To Detect Common Dental Diseases, As Compared With Dental X-Ray, Yoshita Viraj Holamoge

LSU Master's Theses

Oral health is indicative of a person’s overall health. Even with advances in medical science, dental diseases are very much prevalent in our society. Dental imaging techniques help in the early detection of these dental diseases and eventually avoids the risk of poor oral health as well as medical expenses. Current dental imaging techniques rely mostly on X-ray imaging whose ionizing property is a concern amongst the population. Near-infrared spectrum is known to have tissue penetration property and they belong to the non-ionizing part of the electromagnetic spectrum. This study utilized a contrast agent assisted near-infrared imaging for common dental …

Developing An Optomechanical Approach For Characterizing Mechanical Properties Of Single Adherent Cells, Ali Mehrnezhad

LSU Doctoral Dissertations

Mechanical properties of a cell reflect its biological and pathological conditions including cellular disorders and fundamental cellular processes such as cell division and differentiation. There have been active research efforts to develop high-throughput platforms to mechanically characterize single cells. Yet, many of these research efforts are focused on suspended cells and use a flow-through configuration. Therefore, adherent cells are detached prior to the characterization, which seriously perturbs the cellular conditions. Also, methods for adherent cells are limited in their throughput.

My study is aimed to fill the technical gap in the field of single cell analysis, which is a high-throughput …

Wearable Sensor Network Of Inertial Measurement Units To Track, Classify, And Assess Performance Of Complex Body Motions, Richard Tuggle

Research Horizons Day Posters

No abstract provided.

An Electrooculography Prosthetic Control System, Walker Arce

UNO Student Research and Creative Activity Fair

For many surface EMG (sEMG) prosthetic control systems, the muscles on the affected limb are used to trigger the control system. This can lead to fatigue in the user as they have to maintain continuous muscle activation and coactivation in order to achieve prosthetic control [3]. The crux of any prosthetic control system is the human machine interface that is developed, and at present many control systems have complicated interfaces that limit the degrees of freedom of the prosthetics. This study focuses on the development of a low-cost prosthetic control peripheral that is compatible with the prosthetics developed by Dr. …

A Voice Activated Prosthetic Mode Of Control, Will Picken

UNO Student Research and Creative Activity Fair

There are many options for a prosthetic mode of control. The most commonly created modes of control involve surface EMG (sEMG) and require that the user have well defined muscle activation in order to trigger the movement of the prosthetic. Unfortunately, many prosthetic users do not have the required muscle tone or strength to trigger these sensors, so the need for a control mechanism that doesn’t rely on sEMG is clear. This study focuses on the development of a low-cost, voice activated prosthetic mode of control compatible with the prosthetics developed by Dr. Zuniga and his research team.

The printed …

A Radio Frequency Identification (Rfid) Prosthetic Control System, Andrew Butler

UNO Student Research and Creative Activity Fair

Item classification and tagging in embedded systems has become ubiquitous in our society due to radio frequency identification (RFID) and the cost has dropped significantly for hardware that can interact with these devices. Due to this, possibilities in the realm of prosthetic control systems opens up for dynamic grip selection without user intervention. This study focuses on the development of a device capable of this functionality that is compatible with the prosthetics designed by Dr. Zuniga and his research team.

The printed circuit board (PCB) was designed using the EAGLE EDA package and incorporates a lithium polymer battery with a …

Development Of A Myoelectric Detection Circuit Platform For Computer Interface Applications, Nickolas Andrew Butler

Master's Theses

Personal computers and portable electronics continue to rapidly advance and integrate into our lives as tools that facilitate efficient communication and interaction with the outside world. Now with a multitude of different devices available, personal computers are accessible to a wider audience than ever before. To continue to expand and reach new users, novel user interface technologies have been developed, such as touch input and gyroscopic motion, in which enhanced control fidelity can be achieved. For users with limited-to-no use of their hands, or for those who seek additional means to intuitively use and command a computer, novel sensory systems …

Design And Optimization Of An Ionizing-Radiation-Free Dental Imaging Scheme By Near Infrared Fluorescence, Thomas Hartzler

LSU Master's Theses

There is a global need for access to oral health care. Proper oral health care is necessary for physiological and psychological health, as well as social and economic issues. Major oral diseases that must be screened include caries, cracked teeth, and impacted molars. These diseases are screened and diagnosed using a variety of medical imaging methods, computed tomography (CT) X-ray being the most popular and efficient method. The challenges in screening with X-ray technology include financial and time cost as well as health risk, including radiation exposure induced cancer (REIC). This thesis summarizes research to explore the possibility of overcoming …

Extended-Use Ecg Monitor, Daniel Aaron Soski

Master's Theses

In this thesis, a prototype ECG monitor was developed that is integrated into an elastic shirt and takes a 3-lead ECG for over 5 days. The high-quality measurements can be used to identify markers indicative of various detrimental heart conditions. Measurements recorded by the device are encrypted and stored onto a micro-SD card. Current Holter monitors are expensive and have functional lives less than 48 hours; however, extended duration monitoring has been proven more useful in diagnosis. The device designed demonstrates that ECG measurements can be taken over longer durations without sacrificing quality, comfort, or device cost.

Evaluation Of Terahertz Imaging For Breast Cancer Detection Using Image Morphing, Tanny Andrea Chavez Esparza

Graduate Theses and Dissertations

This thesis proposes the use of a mesh morphing algorithm for the quantitative evaluation of terahertz (THz) images. This work differs from traditional evaluation methods based on qualitative evaluation because it provides a fair and quantitative measurement of the THz imaging system's performance. The objective of the algorithm is to match the alignment, shape, and resolution of the THz and reference pathology images. Therefore, the proposed morphing method provides a pathology reference for a pixel-by-pixel evaluation of the region classification in the THz image. To achieve this, the morphing algorithm aligns the images using the Pearson's correlation coefficient and reshapes …

Image Processing Applications In Real Life: 2d Fragmented Image And Document Reassembly And Frequency Division Multiplexed Imaging, Houman Kamran Habibkhani

LSU Doctoral Dissertations

In this era of modern technology, image processing is one the most studied disciplines of signal processing and its applications can be found in every aspect of our daily life. In this work three main applications for image processing has been studied.

In chapter 1, frequency division multiplexed imaging (FDMI), a novel idea in the field of computational photography, has been introduced. Using FDMI, multiple images are captured simultaneously in a single shot and can later be extracted from the multiplexed image. This is achieved by spatially modulating the images so that they are placed at different locations in the …

Power Mobility Sensor Data Collection Verified Through Standardized Pediatric Assessments, Ayshka Elise Rodriguez-Velez

UNF Graduate Theses and Dissertations

The collaboration between the School of Engineering and the Department of Physical Therapy at the University of North Florida has introduced the possibility of creating a new environment for pediatric physical therapy assessments. There are currently no methods for remotely monitoring children with impairments. However, with embedded sensor technology in the form of power mobility and accepted therapy assessment tools, remote monitoring can become a possibility. As a part of this work, a ride-on toy car was developed as a remote monitoring device and a case study with a child with a mobility impairment was used as a proof of …

Wax Bee Gone: A Safe, Effective Solution To Ear Wax Removal, Robert G. Shenon, Shanvir S. Dhinsa

Electrical Engineering

This project sought to combine conventional methods such as scraping and water pressure to removal ear wax, but with electronic automation to removal the potential for human error as much as possible. Through the use of a 9V battery, and Arduino microcontroller, DC motors, and other circuitry, this project has developed a prototype for a device that can properly remove ear wax without any discomfort or risk to the user. Much of this project involved learning how to properly manipulate and provide the necessary power requirements DC motors from an Arduino and a 9V battery. Additionally, creating a 3D printed …