Electrical and Computer Engineering Commons^™

Foreground Removal In A Multi-Camera System, Daniel T. Mortensen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Traditionally, whiteboards have been used to brainstorm, teach, and convey ideas with others. However distributing whiteboard content remotely can be challenging. To solve this problem, A multi-camera system was developed which can be scaled to broadcast an arbitrarily large writing surface while removing objects not related to the whiteboard content. Related research has been performed previously to combine multiple images together, identify and remove unrelated objects, also referred to as foreground, in a single image and correct for warping differences in camera frames. However, this is the first time anyone has attempted to solve this problem using a multi-camera system. …

Development Of A Comsol Microdialysis Model, Towards Creation Of Microdialysis On A Chip With Improved Geometries And Recovery, Patrick Pysz

Graduate Theses and Dissertations

Microdialysis (µD) sampling is a diffusion-limited sampling method that has been widely used in different biomedical fields for greater than 35 years. Device calibration for in vivo studies is difficult for current non-steady state analytes of interest correlated with both inflammatory response and microbial signaling molecules (QS); which exist in low ng/mL to pg/mL with molecular weights over a wide range of 170 Da to 70 kDa. The primary performance metric, relative recovery (RR), relating the collected sample to the extracellular space concentration varies from 10% to 60% per analyte even under controlled bench-top conditions. Innovations in microdialysis device design …

Evaluation And Analysis Of Null Convention Logic Circuits, John Davis Brady

Graduate Theses and Dissertations

Integrated circuit (IC) designers face many challenges in utilizing state-of-the-art technology nodes, such as the increased effects of process variation on timing analysis and heterogeneous multi-die architectures that span across multiple technologies while simultaneously increasing performance and decreasing power consumption. These challenges provide opportunity for utilization of asynchronous design paradigms due to their inherent flexibility and robustness.

While NULL Convention Logic (NCL) has been implemented in a variety of applications, current literature does not fully encompass the intricacies of NCL power performance across a variety of applications, technology nodes, circuit scale, and voltage scaling, thereby preventing further adoption and utilization …

A Review Of Integrated Propulsion, Suspension And Guidance Passive Guideway Maglev Technologies, Jonathan Bird

Electrical and Computer Engineering Faculty Publications and Presentations

This paper provides a review of integrated propulsion, suspension and guidance maglev technology that use fully passive guideway structures.

Transmission-Scale Battery Energy Storage Systems: A Systematic Literature Review, Kevin Marnell, Manasseh Obi, Robert B. Bass

Electrical and Computer Engineering Faculty Publications and Presentations

When the transmission capacity of an electrical system is insufficient to adequately serve customer demand, the transmission system is said to be experiencing congestion. More transmission lines can be built to increase capacity. However, transmission congestion typically only occurs during periods of peak demand, which occur just a few times per year; capitol-intensive investments in new transmission capacity address problems that occur infrequently. Alternative solutions to alleviated transmission congestion have been devised, including generation curtailment, demand response programs, and various remedial action schema. Though not currently a common solution, battery energy storage systems can also provide transmission congestion relief. Technological …

Air Quality Monitoring Wireless Sensor Network With Electrochemical Sensing Elements, Saeed Faisal Malky

Theses and Dissertations

Harmful atmospheric pollutants have been attributed to causing adverse weather conditions and health problems, which are particularly prevalent in more populated global regions, such as megacities. Nongovernmental and international agencies throughout the world have likewise called for increased awareness and action to effectively counter the increased rates of air pollution, as the consequences seem ominous. Meanwhile, in several major urban landscapes such as Saudi Arabia, no modern apparatus or efficient systematic mechanisms exist for the qualitative detection of dangerous pollutants and gases. The current counterparts for hazardous gas measurements are expensive, bulky and cumbersome to set up. Thus, sensor devices …

Built-In Return-Oriented Programs In Embedded Systems And Deep Learning For Hardware Trojan Detection, Nathanael R. Weidler

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Microcontrollers and integrated circuits in general have become ubiquitous in the world today. All aspects of our lives depend on them from driving to work, to calling our friends, to checking our bank account balance. People who would do harm to individuals, corporations and nation states are aware of this and for that reason they seek to find or create and exploit vulnerabilities in integrated circuits. This dissertation contains three papers dealing with these types of vulnerabilities. The first paper talks about a vulnerability that was found on a microcontroller, which is a type of integrated circuit. The final two …

Gpu-Accelerated Demodulation For A Satellite Ground Station, Emily Clark Young

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

One consequence of the increasing number of small satellite missions is an increasing demand for high data rate downlinks. As the satellites transmit at high data rates, ground-side receivers need to demodulate the transmitted data as quickly as possible. While application specific hardware can be designed, software defined radio solutions for ground stations are attractive for their flexibility, adaptability, and portability.

Another industry trend is the increasing use of Graphics Processing Units (GPUs) in general-purpose processing. By performing many operations simultaneously, GPUs are capable of accelerating processing when given a problem that can be implemented in a parallel manner. Furthermore, …

Visual Speech Recognition Using A 3d Convolutional Neural Network, Matthew Rochford

Master's Theses

Main stream automatic speech recognition (ASR) makes use of audio data to identify spoken words, however visual speech recognition (VSR) has recently been of increased interest to researchers. VSR is used when audio data is corrupted or missing entirely and also to further enhance the accuracy of audio-based ASR systems. In this research, we present both a framework for building 3D feature cubes of lip data from videos and a 3D convolutional neural network (CNN) architecture for performing classification on a dataset of 100 spoken words, recorded in an uncontrolled envi- ronment. Our 3D-CNN architecture achieves a testing accuracy of …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Microwave Tunneling And Robust Information Transfer Based On Parity-Time-Symmetric Absorber-Emitter Pairs, Zhicheng Xiao, Younes Ra’Di, Sergei Tretyakov, Andrea Alù

Advanced Science Research Center

Robust signal transfer in the form of electromagnetic waves is of fundamental importance in modern technology, yet its operation is often challenged by unwanted modifications of the channel connecting transmitter and receiver. Parity-time- (PT-) symmetric systems, combining active and passive elements in a balanced form, provide an interesting route in this context. Here, we demonstrate a PT-symmetric microwave system operating in the extreme case in which the channel is shorted through a small reactance, which acts as a nearly impenetrable obstacle, and it is therefore expected to induce large reflections and poor transmission. After placing a gain element behind the …

Gamma-Ray Radiation Effects In Graphene-Based Transistors With H-Bn Nanometer Film Substrates, E. J. Cazalas, Michael R. Hogsed, S. R. Vangala, Michael R. Snure, John W. Mcclory

Faculty Publications

Radiation effects on graphene field effect transistors (GFETs) with hexagonal boron nitride (h-BN) thin film substrates are investigated using 60Co gamma-ray radiation. This study examines the radiation response using many samples with varying h-BN film thicknesses (1.6 and 20 nm thickness) and graphene channel lengths (5 and 10 μm). These samples were exposed to a total ionizing dose of approximately 1 Mrad(Si). I-V measurements were taken at fixed time intervals between irradiations and postirradiation. Dirac point voltage and current are extracted from the I-V measurements, as well as mobility, Dirac voltage hysteresis, and the total number of GFETs that remain …

Optical Angular Scatterometry: In-Line Approach For Roll-2-Roll And Nano-Imprint Fabrication Systems, Juan Jose Faria-Briceno

Electrical and Computer Engineering ETDs

As critical dimensions continue to shrink and structures become more complex, metrology processes are challenging to implement during in-line nanomanufacturing. Non-destructive, non-contact, and high-speed conditions are required to achieve proper metrology processes during in-line manufacturing. Optical scatterometry is a nanoscale metrology tool widely used in integrated circuit manufacturing for characterization and quality control. However, most applications of optical scatterometry operate off-line. A high-speed, in-line, non-contact, non-destructive scatterometry angular system has been demonstrated in this work to scan pattern surfaces during real-time nano-fabrication.

Our system has demonstrated scanning capabilities using flat, 1D and 2D complex structures. The flat surface samples consist …

Indocyanine-Green-Assisted Near-Infrared Dental Fluorescence Imaging To Detect Common Dental Diseases, As Compared With Dental X-Ray, Yoshita Viraj Holamoge

LSU Master's Theses

Oral health is indicative of a person’s overall health. Even with advances in medical science, dental diseases are very much prevalent in our society. Dental imaging techniques help in the early detection of these dental diseases and eventually avoids the risk of poor oral health as well as medical expenses. Current dental imaging techniques rely mostly on X-ray imaging whose ionizing property is a concern amongst the population. Near-infrared spectrum is known to have tissue penetration property and they belong to the non-ionizing part of the electromagnetic spectrum. This study utilized a contrast agent assisted near-infrared imaging for common dental …

A-Posteriori Estimation Of Random Uncertainty For The Reflection Type Q-Factor Measurements, Darko Kajfez

Engineering Software

No abstract provided.

Measurement Of Photoionization Rates In Air, Justin K. Smith

Electrical and Computer Engineering ETDs

The ionization of gas molecules from the absorption of photons produced in different parts of a discharge is an important process in the development of streamers. Photoionization rates are essential in the propagation of streamers and are therefore important in simulations of computational codes. Although streamers are widely used in computational codes, there is a limited data set on the experiments measuring photoionization rates in gases. Usually, the photoionization rate data used in computational codes comes from a single source and the validity of this data combined with the photoionization model has been questionable. It is postulated there is a …

Software Design For Probabilistic Safety: Stochastic Reachability And Circadian Control, Joseph D. Gleason

Electrical and Computer Engineering ETDs

Stochastic reachability is an important verification tool that provides probabilistic assurances of safety in a variety of contexts. In engineered systems, safety may be synonymous with the ability of the system to avoid "bad" constraints on the state space, that constitute collision, departure from a flight envelope, or other undesirable phenomenon. In biomedical systems, assurance of safety (such as the mandate to ``do no harm'') are considerably complicated by the fact that there is a lack of physics-driven models, extensive signal processing is needed to capture the underlying state of the system, and the stochasticity inherent to the system may …

Vision-Based Autonomous Tracking Of A Non-Cooperative Mobile Robot By A Low-Cost Quadrotor Vehicle, Cheikhna Ahmed Tidiane Sy

Electrical and Computer Engineering ETDs

The goal of this thesis is the detection and tracking of a ground vehicle, in particular a car-like robot, by a quadrotor. The first challenge to address in any pursuit or tracking scenario is the detection and unique identification of the target. From this first challenge, comes the need to precisely localize the target in a coordinate system that is common to the tracking and tracked vehicles. In most real-life scenarios, the tracked vehicle does not directly communicate information such as its position to the tracking one. From this fact, arises a non-cooperative constraint problem. The autonomous tracking aspect of …

Validation Of Gaseous Absorption & Cloud Attenuation Models Utilizing A 72 Ghz Terrestrial Link, Ralph Lyndon Gesner

Electrical and Computer Engineering ETDs

Interest in the W & V-bands of the radio frequency (RF) spectrum has become steadily more desirable for system designers due to the ever increasing need for greater communication bandwidths and higher data rates. The 40 GHZ to 110 GHz range that constitutes the W & V-bands provide a unique solution to both of these current demands by providing a bandwidth nearly double that of all current RF frequencies in use. To date, this range has only been used for point to point satellite and short link communications meaning these bands have remained largely unexplored and undeveloped.

To capitalize on …

Integrated Chirped-Grating Spectrometer-On-A-Chip, Shima Nezhadbadeh

Optical Science and Engineering ETDs

In this dissertation we demonstrate a new structure based on waveguide coupling atop a silicon wafer using a chirped grating to provide the dispersion that leads to a high-resolution, compact, fully integrable and CMOS-compatible spectrometer. Light is both analyzed and detected in a single, completely monolithic component which enables realizing a high-resolution portable spectrometer with an extremely compact footprint. The structure is comprised of a SiO₂/Si₃N₄/SiO₂ waveguide on top of a silicon wafer. Grating regions are fabricated on the top cladding of the waveguide. The input light is incident on a chirped grating …

Security Of The Internet Of Things: Vulnerabilities, Attacks And Countermeasures, Ismail Butun, Houbing Song, Patrik Osterberg

Publications

Wireless Sensor Networks (WSNs) constitute one of the most promising third-millennium technologies and have wide range of applications in our surrounding environment. The reason behind the vast adoption of WSNs in various applications is that they have tremendously appealing features, e.g., low production cost, low installation cost, unattended network operation, autonomous and longtime operation. WSNs have started to merge with the Internet of Things (IoT) through the introduction of Internet access capability in sensor nodes and sensing ability in Internet-connected devices. Thereby, the IoT is providing access to huge amount of data, collected by the WSNs, over the Internet. Hence, …

Bio-Mechanical Characterization Of Adherent Cell Layers With A Pdms Cantilever, Merrel Truly Holley

LSU Doctoral Dissertations

In the last few decades, the mechanical characteristics of human cells has been linked to many physiological processes and pathological conditions, illustrating the importance as effective biomarkers. Mounting research has shown the mechanical force between cells and the extracellular matrix (ECM) plays a vital role in cellular processes such as tissue homeostasis, wound healing, cancer metastasis, and the progression of various diseases. This mechanical force, or the force that a cell produces on its surroundings, is termed as the cellular traction force (CTF). Precise characterization of the CTF can expand our knowledge of these important cellular processes as well as …

Water Pipeline Leakage Detection Based On Machine Learning And Wireless Sensor Networks, Yang Liu, Xuehui Ma, Yong Tie, Yinghui Zhang, Jing Gao

Department of Electrical and Computer Engineering: Faculty Publications

The detection of water pipeline leakage is important to ensure that water supply networks can operate safely and conserve water resources. To address the lack of intelligent and the low efficiency of conventional leakage detection methods, this paper designs a leakage detection method based on machine learning and wireless sensor networks (WSNs). The system employs wireless sensors installed on pipelines to collect data and utilizes the 4G network to perform remote data transmission. A leakage triggered networking method is proposed to reduce the wireless sensor network’s energy consumption and prolong the system life cycle effectively. To enhance the precision and …

Machine Current Sensor Fdi Strategy In Pmsms, Haibo Li, Yi Qian, Sohrab Asgarpoor, Hamid Sharif

Department of Electrical and Computer Engineering: Faculty Publications

This work proposes a machine current sensor fault detection and isolation (FDI) strategy in permanent magnet synchronous machines (PMSMs) resilient to multiple faults. The fault detection is performed by comparing the measured and estimated DC link currents. The fault isolation is achieved according to machine phase signal estimation and the corresponding residual examination. Single sensor fault, multiple sensor faults and non-sensor fault are covered by the proposed FDI method. The proposed sensor FDI method is not influenced by machine imbalance, feasible for FDI of both single and multiple machine current sensor faults, and capable of distinguishing between machine current sensor …

Performance Of Desiccant Enhanced Evaporative Cooling System Based On High-Low Control, Yi Chen, Huaxia Yan, Yimo Luo

Faculty of Science & Technology (THEi)

Desiccant enhanced evaporative cooling system is a sustainable air-conditioning (A/C) system which deals the latent load and sensible load separately by a dehumidifier and an evaporative cooler. A LDD-RIEC system consists of a liquid desiccant dehumidifier (LDD) and a regenerative indirect evaporative cooler (RIEC) were investigated. The LDD-RIEC system is characterized by low energy consumption compared with conventional mechanical cooling system, but the main shortcoming is the high dependency on ambient air conditions. To maintain stable indoor temperature, a control scheme is essential. However, very limited research work regarding control strategy can be found in open literatures. In this paper, …

Experimental Testing Of A 3d-Printed Metamaterial Slow Wave Structure For High Power Microwave Generation, Antonio B. De Alleluia

Electrical and Computer Engineering ETDs

A metamaterial (MTM) high power microwave (HPM) vacuum electron device (VED) was developed using 3D printing technology. The specific geometric pattern of the source can produce both negative permittivity and permeability to interact with a relativistic electron beam. The electron beam is generated using a pulsed electron accelerator with a maximum energy of 700 keV and lasting approximately 16 ns. The design of this novel VED consists of a circular waveguide loaded with complementary split-ring resonators in a linear periodic arrangement in which the relativistic beam travels guided by a magnetic field. The electrons interact with the MTM producing electromagnetic …

Demand Response Management In Smart Grid Networks: A Two-Stage Game-Theoretic Learning-Based Approach, Pavlos Athanasios Apostolopoulos

Electrical and Computer Engineering ETDs

In this diploma thesis, the combined problem of power company selection and Demand Response Management in a Smart Grid Network consisting of multiple power companies and multiple customers is studied via adopting a distributed learning and game-theoretic technique. Each power company is characterized by its reputation and competitiveness. The customers who act as learning automata select the most appropriate power company to be served, in terms of price and electricity needs’ fulfillment, via a distributed learning based mechanism. Given customers' power company selection, the Demand Response Management problem is formulated as a two-stage game theoretic optimization framework, where at the …

5-Bit Dual-Slope Analog-To-Digital Converter-Based Time-To-Digital Converter Chip Design In Cmos Technology, Jojoe S. Sagoe

LSU Master's Theses

Time-to-Digital Converters (TDC) have gained increasing importance in modern implementations of mixed-signal, data-acquisition and processing interfaces and are used to perform high precision time intervals in systems that incorporate Time-of-Flight (ToF) or Time-of-Arrival (ToA) measurements. The linearity of TDCs is very crucial since most Digital Signal Processing (DSP) systems require very linear inputs to achieve high accuracy.

In this work, a TDC has been designed in the 0.5 μm n-well CMOS process that can be used for on-chip integration and in applications requiring high linearity. This TDC used a Dual-Slope-ADC-based architecture for the time-to-digital conversion and consists of the following …

Overview Of Flywheel Systems For Renewable Energy Storage With A Design Study For High-Speed Axial-Flux Permanent-Magnet Machines, Murat G. Kesgin, Peng Han, Narges Taran, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Flywheel energy storage is considered in this paper for grid integration of renewable energy sources due to its inherent advantages of fast response, long cycle life and flexibility in providing ancillary services to the grid, such as frequency regulation, voltage support, etc. The fundamentals of the technology and recent developments are reviewed, firstly with an emphasis on the design considerations and performance metrics. Then the progress and development trends in electric motor/generators employed in flywheel energy storage systems (FESS) are summarized, showing the potential of axial-flux permanent-magnet (AFPM) machines in such applications. Design examples of high-speed AFPM machines are provided …

An Open-Source Integration Platform For Multiple Peripheral Modules With Kuka Robots, Mahyar Abdeetedal, Mehrdad Kermani Ph.D., P.Eng.

Electrical and Computer Engineering Publications

This paper presents an open-source software interface for the integration of a Kuka robot with peripheral tools and sensors, KUI: Kuka User Interface. KUI is developed based on Kuka Fast Research Interface (FRI) which enables soft real-time control of the robot. Simulink Desktop Real-Time™ or any User Datagram Protocol (UDP) client can send real-time commands to Kuka robot via KUI. In KUI, third-party tools can be added and controlled synchronously with Kuka light-weight robot (LWR). KUI can send the control commands via serial communication to the attached devices. KUI can generate low-level commands using data acquisition (DAQ) boards. This feature …