Electrical and Computer Engineering Commons^™

Survivable Multicasting In Wdm Optical Networks, Sateesh Chandra Shekhar

LSU Master's Theses

Opportunities abound in the global content delivery service market and it is here that multicasting is proving to be a powerful feature. In WDM networks, optical splitting is widely used to achieve multicasting. It removes the complications of optical-electronic-optical conversions [1]. Several multicasting algorithms have been proposed in the literature for building light trees. As the amount of fiber deployment increases in networks, the risk of losing large volumes of data traffic due to a fiber span cut or due to node failure also increases. In this thesis we propose heuristic schemes to make the primary multicast trees resilient to …

Testing A Cmos Operational Amplifier Circuit Using A Combination Of Oscillation And Iddq Test Methods, Pavan K. Alli

LSU Master's Theses

This work presents a case study, which attempts to improve the fault diagnosis and testability of the oscillation testing methodology applied to a typical two-stage CMOS operational amplifier. The proposed test method takes the advantage of good fault coverage through the use of a simple oscillation based test technique, which needs no test signal generation and combines it with quiescent supply current (IDDQ) testing to provide a fault confirmation. A built in current sensor (BICS), which introduces insignificant performance degradation of the circuit-under-test (CUT), has been utilized to monitor the power supply quiescent current changes in the CUT. The testability …

Iddq Testing Of A Cmos First Order Sigma-Delta Modulator Of An 8-Bit Oversampling Adc, Anand K. Chamakura

LSU Master's Theses

This work presents IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling analog-to-digital converter using a built-in current sensor [BICS]. Gate-drain, source-drain, gate-source and gate-substrate bridging faults are injected using fault injection transistors. All the four faults cause varying fault currents and are successfully detected by the BICS at a good operation speed. The BICS have a negligible impact on the performance of the modulator and an external pin is provided to completely cut-off the BICS from the modulator. The modulator was designed and fabricated in 1.5 μm n-well CMOS process. The decimator was designed on …

Zooplankton Visualization System: Design And Real-Time Lossless Image Compression, Dattatreya Reddy Tetala Satya Surya

LSU Master's Theses

In this thesis, I present a design of a small, self-contained, underwater plankton imaging system. I base the imaging system’s design on an embedded PC architecture based on PC/104-Plus standards to meet the compact size and low power requirements. I developed a simple graphical user interface to run on a real-time operating system to control the imaging system. I also address how a real-time image compression scheme implemented on an FPGA chip speeds up image transfer speeds of the imaging system. Since lossless compression of the image is required in order to retain all image details, I began with an …

An Evaluation Of Multiple Branch Predictor And Trace Cache Advanced Fetch Unit Designs For Dynamically Scheduled Superscalar Processors, Slade S. Maurer

LSU Master's Theses

Semiconductor feature size continues to decrease permitting superscalar microprocessors to continue to increase the number of functional units available for execution. As the instruction issue width increases beyond the five instruction average basic block size of integer programs, more than one basic block must be issued per cycle to continue to increase instructions per cycle (IPC) performance. Researchers have created methods of fetching instructions beyond the first taken branch to overcome the bottleneck created by the limitations of conventional single branch predictors. We compare the performance of the multiple branch prediction (MBP) and trace cache (TC) fetch unit optimization methods. …

Design And Performance Of Electric Shock Absorber, Oly D. Paz

LSU Master's Theses

The electric shock absorber is a device that converts the kinetic energy of an oscillating object into electric energy. This kinetic energy is normally dumped in a form of thermal energy in a conventional, mechanical shock absorber. The electric shock absorber consists of a permanent magnet linear synchronous generator (PMLSG), a spring, and an electric energy accumulator. The major goal of the project is to design and analyze the operation of an electric shock absorber. In order to define the initial requirements that the electric shock absorber has to satisfy, the construction and performance of currently used shock absorbers were …

First Order Sigma-Delta Modulator Of An Oversampling Adc Design In Cmos Using Floating Gate Mosfets, Syam Prasad Sbs Kommana

LSU Master's Theses

We report a new architecture for a sigma-delta oversampling analog-to-digital converter (ADC) in which the first order modulator is realized using the floating gate MOSFETs at the input stage of an integrator and the comparator. The first order modulator is designed using an 8 MHz sampling clock frequency and implemented in a standard 1.5µm n-well CMOS process. The decimator is an off-chip sinc-filter and is programmed using the VERILOG and tested with Altera Flex EPF10K70RC240 FPGA board. The ADC gives an 8-bit resolution with a 65 kHz bandwidth.

Watermarking Using Decimal Sequences, Navneet Kumar Mandhani

LSU Master's Theses

This thesis introduces the use of decimal sequences in watermarking to hide information for authentication. The underlying system is based on code division multiple access (CDMA), which is a form of spread spectrum communication. Different algorithms for the use of decimal sequences have been formulated for use in black and white images. The watermark is spread across the carrier image by using the d- sequences of optimal period and retrieval is made by the use of correlation. Matlab version 6.5 was used to implement the algorithms discussed in this thesis. The advantage of using d-sequences over PN sequences is that …

High-Field Quasi-Ballistic Transport In Short Carbon Nanotubes, Ali Javey, Jing Guo, Magnus Paulsson, Qian Wang, Mark S. Lundstrom, Hongjie Dai, David Mann

Department of Electrical and Computer Engineering Faculty Publications

Single walled carbon nanotubes with Pd Ohmic contacts and lengths ranging from several microns down to 10 nm are investigated by electron transport experiments and theory. The mean-free path (MFP) for acoustic phonon scattering is estimated to be lap ~300  nm, and that for optical phonon scattering is lop ~15  nm. Transport through very short (~10  nm) nanotubes is free of significant acoustic and optical phonon scattering and thus ballistic and quasiballistic at the low- and high-bias voltage limits, respectively. High currents of up to 70   μA can flow through a short nanotube. Possible mechanisms for the eventual electrical breakdown …

A Three-Dimensional Quantum Simulation Of Silicon Nanowire Transistors With The Effective Mass Approximation, Jing Wang, Eric Polizzi, Mark S. Lundstrom

Department of Electrical and Computer Engineering Faculty Publications

The silicon nanowire transistor (SNWT) is a promising device structure for future integrated circuits, and simulations will be important for understanding its device physics and assessing its ultimate performance limits. In this work, we present a three-dimensional (3D) quantum mechanical simulation approach to treat various SNWTs within the effective-mass approximation. We begin by assuming ballistic transport, which gives the upper performance limit of the devices. The use of a mode space approach (either coupled or uncoupled) produces high computational efficiency that makes our 3D quantum simulator practical for extensive device simulation and design. Scattering in SNWTs is then treated by …

Monolithic Integration Of Dual Optical Elements On High Power Semicond, Laurent Vaissie

Electronic Theses and Dissertations

This dissertation investigates the monolithic integration of dual optical elements on high power semiconductor lasers for emission around 980nm wavelength. In the proposed configuration, light is coupled out of the AlGaAs/GaAs waveguide by a low reflectivity grating coupler towards the substrate where a second monolithic optical element is integrated to improve the device performance or functionality. A fabrication process based on electron beam lithography and plasma etching was developed to control the grating coupler duty cycle and shape. The near-field intensity profile outcoupled by the grating is modeled using a combination of finite-difference time domain (FDTD) analysis of the nonuniform …

General Interference Suppression Technique For Diversity Wireless Rece, Tianyu Yang

Electronic Theses and Dissertations

The area of wireless transceiver design is becoming increasingly important due to the rapid growth of wireless communications market as well as diversified design specifications. Research efforts in this area concentrates on schemes that are capable of increasing the system capacity, providing reconfigurability/reprogrammability and reducing the hardware complexity. Emerging topics related to these goals include Software Defined Radio, Multiple-Input-Multiple-Output (MIMO) Systems, Code Division Multiple Access, Ultra-Wideband Systems, etc. This research adopts space diversity and statistical signal processing for digital interference suppression in wireless receivers. The technique simplifies the analog front-end by eliminating the anti-aliasing filters and relaxing the requirements for …

Towards A Unified Spatial-Temporal Data Model And Query Language For Geographical Information Systems., Patrick Browne, Mike Jackson

Conference papers

This paper outlines the principle features of a Ph.D. programme of work. Section one describes the aims of the research. Section two looks at the nature of digital maps and their importance in the broader context of geographic information. Section three looks at the two major aspects of the research. Section four discusses the role of category theory in the research. Finally the conclusion is presented in section five.

Luminescence In Zno, Jin Xu

Theses and Dissertations

As a wide band semiconductor with a large binding energy (about 60meV), ZnO is a promising candidate semiconductor material for the next generation of optoelectronic , light emission or high power and high frequency devices. In order to make electrical device from ZnO, it is necessary to investigate optical properties of ZnO.In this thesis, PL setup and the properties of ZnO are introduced briefly and the optical properties of ZnO are investigated in detail. Temperature dependence of PL spectra of ZnO are measured and analyzed. Sharp emission line of PL spectra of rare earth (RE) doped ZnO are also investigated.

Effect Of Stochastic Dead Space On Noise In Avalanche Photodiodes, Oh-Hyun Kwon, Majeed M. Hayat, Joe C. Campbell, Bahaa E.A. Saleh, Malvin Carl Teich

Electrical and Computer Engineering Faculty Research and Publications

A stochastic dead-space model for impact ionization is developed and used to study the effect of the soft nature of the ionization capability of carriers on the excess noise factor of avalanche photodiodes. The proposed model is based on the rationale that the gradual, or soft, transition in the probability density function (PDF) for the distance from birth to impact ionization can be viewed as that resulting from uncertainty in the dead space itself. The resulting soft PDF, which is parameterized by a tunable softness parameter, is used to establish the limitations of the existing hard-threshold ionization models in ultrathin …

Design And Analysis Of An R-Shaped Dual-Band Planar Inverted-F Antenna For Vehicular Applications, Mohammod Ali, Guangli Yang, Huan-Sheng Hwang, Tuangsit Sittironnarit

Faculty Publications

A dual-band R-shaped planar inverted-F antenna is proposed for vehicular application. Utilization of this unique geometry dual-frequency operation is achieved with a single feed. The proposed antenna operates in the 225- and 450-MHz bands. Input impedance and return loss data as function of various antenna parameters are presented, which show that parameters can be adjusted in order to obtain optimum tuning. Radiation pattern data for the antenna mounted on the roof of two types of vehicles are given. The pattern in the low-frequency band is essentially omnidirectional while that in the high-frequency band is directional and normal to the antenna …

Investigation Of Femtosecond Laser-Assisted Micromachining Of Lithium Niobate, A. Malshe, D. Deshpande, E. Stach, Kamlakar Rajurkar, Dennis R. Alexander

Department of Electrical and Computer Engineering: Faculty Publications

Lithium Niobate has a potential for applications in electronics and communication industries due to its unique electro-optical, piezoelectric and nonlinear properties. Femtosecond laser machining offers the best alternative to machine the mechanically fragile and optically delicate lithium niobate crystal. This paper reports a study of the effect of femtosecond laser machining on the surface integrity of lithium niobate. The transmission electron microscopy reveals a 100nm thin amorphous region and a void. The chemical analysis shows a loss of lithium and oxygen from the surface and sub-surface. Optical illumination facilitates the selective readout of the written spots of 2 microns size.

Exploration Of Artificial Multiferroic Thin-Film Heterostructures Using Composition Spreads, K.-S. Chang, M. A. Aronova, C.-L. Lin, M. Murakami, M.-H. Yu, Jason R. Hattrick-Simpers, O. O. Famodu, S. Y. Lee, R. Ramesh, M. Wuttig, I. Takeuchi, C. Gao, L. A. Bendersky

Faculty Publications

We have fabricated a series of composition spreads consisting of ferroelectric BaTiO₃ and piezomagnetic CoFe₂O₄ layers of varying thicknesses modulated at nanometer level in order to explore artificial magnetoelectricthin-film heterostructures. Scanning microwavemicroscopy and scanning superconducting quantum interference device microscopy were used to map the dielectric and magnetic properties as a function of continuously changing average composition across the spreads, respectively. Compositions in the middle of the spreads were found to exhibit ferromagnetism while displaying a dielectric constant as high as ≈120.

Interaction Effects Of Slurry Chemistry On Chemical Mechanical Planarization Of Electroplated Copper, Peter A. Miranda, Jerome A. Imonigie, Amy J. Moll

Electrical and Computer Engineering Faculty Publications and Presentations

Recent studies have been conducted investigating the effects of slurry chemistry on the copper CMP process. Slurry pH and hydrogen peroxide concentration are two important variables that must be carefully formulated in order to achieve desired removal rates and uniformity. In applications such as throughwafer vertical interconnects, slurry chemistry effects must be thoroughly understood when copper plating thicknesses can measure up to 20 microns thick. The species of copper present on the surface of the wafer can be controlled through formulation of the slurry chemistry resulting in minimizing non-uniformity while aggressively removing copper. Using a design of experiments (DOE) approach, …

Energy Aware Design And Analysis For Synchronous And Asynchronous Circuits, Jia Di

Retrospective Theses and Dissertations

Power dissipation has become a major concern for IC designers. Various low power design techniques have been developed for synchronous circuits. Asynchronous circuits, however. have gained more interests recently due to their benefits in lower noise, easy timing control, etc. But few publications on energy reduction techniques for asynchronous logic are available.

Power awareness indicates the ability of the system power to scale with changing conditions and quality requirements. Scalability is an important figure-of-merit since it allows the end user to implement operational policy. just like the user of mobile multimedia equipment needs to select between better quality and longer …

Modified Sierpinski Fractal Antenna, Tripti Luintel

Electronic Theses and Dissertations

Fractal antennas have the potential to provide multi-band solution through the property of self similarity that the fractal shape possess. This thesis deals with some modifications of the original Sierpinski fractal patch antenna, providing additional parameters to optimize in order to get the required radiation characteristics. A systematic study of the original Sierpinski monopole was done to gain an insight on the operation and multi-band behavior of the antenna and a similar study was done to find out why the patch version of Sierpinski lacks multi-band behavior. A Sierpinski antenna is designed by merging a grid and the fractal restoring …

Evaluation Of A Microwave Radiative Transfer Model For Calculating Sat, Simonetta Thompson

Electronic Theses and Dissertations

Remote sensing is the process of gathering and analyzing information about the earth's ocean, land and atmosphere using electromagnetic "wireless" techniques. Mathematical models, known as Radiative Transfer Models (RTM), are developed to calculate the observed radiance (brightness temperature) seen by the remote sensor. The RTM calculated brightness temperature is a function of fourteen environmental parameters, including atmospheric profiles of temperature, pressure and moisture, sea surface temperature, and cloud liquid water. Input parameters to the RTM model include data from NOAA Centers for Environmental Prediction (NCEP), Reynolds weekly Sea Surface Temperature and National Ocean Data Center (NODC) WOA98 Ocean Salinity and …

Thermal Management, Beam Control,And Packaging Designs For High Power, Te-Yuan Chung

Electronic Theses and Dissertations

Several novel techniques for controlling, managing and utilizing high power diode lasers are described. Low pressure water spray cooling for a high heat flux system is developed and proven to be an ideal cooling method for high power diode laser arrays. In order to enable better thermal and optical performance of diode laser arrays, a new and simple optical element, the beam control prism, is invented. It provides the ability to accomplish beam shaping and beam tilting at the same time. Several low thermal resistance diode packaging designs using beam control prisms are proposed, studied and produced. Two pump cavity …

Minimization Of Power Dissipation In Digital Circuits Using Pipelining And A Study Of Clock Gating Technique, Ranganath Panchangam

Electronic Theses and Dissertations

Power dissipation is one of the major design issues of digital circuits. The power dissipated by a circuit affects its speed and performance. Multiplier is one of the most commonly used circuits in the digital devices. There are various types of multipliers available depending upon the application in which they are used. In the present thesis report, the importance of power dissipation in today's digital technology is discussed and the various types and sources of power dissipation have been elaborated. Different types of multipliers have been designed which vary in their structure and amount of power dissipation. The concept of …

Autonomous Environmental Mapping In Multi-Agent Uav Systems, Linus Jan Luotsinen

Electronic Theses and Dissertations

UAV units are by many researchers and aviation specialists considered the future and cutting edge of modern flight technology. This thesis discusses methods for efficient autonomous environmental mapping in a multi-agent domain. An algorithm that emphasizes on team work by sharing the agents local map information and exploration intentions is presented as a solution to the mapping problem. General theories on how to model and implement rational autonomous behaviour for UAV agents are presented. Three different human and tactical behaviour modeling techniques are evaluated. The author found the CxBR paradigm to be the most interesting approach. Also, in order to …

Cryptarray A Scalable And Reconfigurable Architecture For Cryptographic Applications, Michael John Lomonaco

Electronic Theses and Dissertations

Cryptography is increasingly viewed as a critical technology to fulfill the requirements of security and authentication for information exchange between Internet applications. However, software implementations of cryptographic applications are unable to support the quality of service from a bandwidth perspective required by most Internet applications. As a result, various hardware implementations, from Application-Specific Integrated Circuits (ASICs), Field-Programmable Gate Arrays (FPGAs), to programmable processors, were proposed to improve this inadequate quality of service. Although these implementations provide performances that are considered better than those produced by software implementations, they still fall short of addressing the bandwidth requirements of most cryptographic applications …

Quantization With Knowledge Base Applied To Geometrical Nesting Problem, Grzegorz Chmaj, Leszek Koszalka

Electrical & Computer Engineering Faculty Research

Nesting algorithms deal with placing two-dimensional shapes on the given canvas. In this paper a binary way of solving the nesting problem is proposed. Geometric shapes are quantized into binary form, which is used to operate on them. After finishing nesting they are converted back into original geometrical form. Investigations showed, that there is a big influence of quantization accuracy for the nesting effect. However, greater accuracy results with longer time of computation. The proposed knowledge base system is able to strongly reduce the computational time.

Implementation Of Arithmetic Primitives Using Truly Deep Submicron Technology (Tdst), Sholeh Eshraghian

Theses: Doctorates and Masters

The invention of the transistor in 1947 at Bell Laboratories revolutionised the electronics industry and created a powerful platform for emergence of new industries. The quest to increase the number of devices per chip over the last four decades has resulted in rapid transition from Small-Scale-Integration (SSI) and Large-Scale-lntegration (LSI), through to the Very-Large-Scale-Integration (VLSI) technologies, incorporating approximately 10 to 100 million devices per chip. The next phase in this evolution is the Ultra-Large-Scale-Integration (ULSI) aiming to realise new application domains currently not accessible to CMOS technology. Although technology is continuously evolving to produce smaller systems with minimised power dissipation, …

Opto-Vlsi Based Wdm Multifunction Device, Selam T. Ahderom

Theses: Doctorates and Masters

The tremendous expansion of telecommunication services in the past decade, in part due to the growth of the Internet, has made the development of high-bandwidth optical net-works a focus of research interest. The implementation of Dense-Wavelength Division Multiplexing (DWDM) optical fiber transmission systems has the potential to meet this demand. However, crucial components of DWDM networks – add/drop multiplexers, filters, gain equalizers as well as interconnects between optical channels – are currently not implemented as dynamically reconfigurable devices. Electronic cross-connects, the traditional solution to the reconfigurable optical networks, are increasingly not feasible due to the rapidly increasing bandwidth of the …

Multiple Scattering Of Light In Inhomogeneous Media And Applications, Claudia Mujat

Electronic Theses and Dissertations

Light scattering-based techniques are being developed for non-invasive diagnostics of inhomogeneous media in various fields, such as medicine, biology, and material characterization. However, as most media of interest are highly scattering and have a complex structure, it is difficult to obtain a full analytical solution of the scattering problem without introducing approximations and assumptions about the properties of the system under consideration. Moreover, most of the previous studies deal with idealized scattering situations, rarely encountered in practice. This dissertation provides new analytical, numerical, and experimental solutions to describe subtle effects introduced by the properties of the light sources, and by …