Electrical and Computer Engineering Commons^™

Measuring And Compensating For Transport Delay In Real-Time Interactive Driving Simulation, Joseph D. Dumas Ii

Retrospective Theses and Dissertations

Real-time, man-in-the-loop simulators are important tools for operator training as well as human performance research. Simulator implementation using digital computers offers many important advantages but may also cause problems. One of the most significant and troublesome artifacts of digital computer simulation is the presence of transport delays in the operator/vehicle control loop. Transport delays have been shown to destabilize the system, resulting in poorer control of the simulated vehicle. They may also contribute to an increased likelihood of simulator sickness in human operators. Therefore, it is desirable to be able to quantify simulator transport delays and to compensate the system …

A Very Lmportant Message From The Board.......

ACUTA: Other Publications

All elected Directors-at-Large must be primary or associate representatives of an Institutional Member.

Elected Directors-at-Large will serve for a term of two (2) years.

An elected Director-at-Large may serve a maximum of two (2) consecutive terms.

Two elected Directors-at-Large will be elected annually by mail ballot. The two candidates receiving the greatest number of votes will be declared to have been elected.

Elected Directors-at-Large will begin their terms of office at the close of the Annual Conference.

In the events of the death, resignation or inability (for any reason) of any elected Director-at-Large to complete their term of Office, the …

Multiple Sample Cryostat For The Determination Of Superconductor Properties, G. Burnside, Roger M. Hawk, Paul C. Mcleod

Journal of the Arkansas Academy of Science

Cryostats which are currently used to characterize the properties of superconductors between 4 K and 100 K are primarily single sample devices. The purpose of this paper is to present an instrument design which can hold up to five (5) one cm. diameter samples at a stable temperature (+ /-0.1K) within the above range specified while measurements of the sample properties are made.

Sputter Deposition And Thallination Of Ti-Ba-Ca-Cu-O Superconducting Thin Films, T. H. Dhayagude, S. S. Ang, W. D. Brown

Journal of the Arkansas Academy of Science

Thallination techniques used for the fabrication of sputter-deposited TI2Ba2CaCu 2Ox and TI2Ba2Ca2Cu3Ox superconducting thin films were investigated. Differences in elemental composition of precursor Ba-Ca-Cu-O sputtering targets were found to yield different superconducting phases. Thallination conditions which yielded transition temperatures as high as 122 K for samples annealed in air are described. Finally, reactive ion etching of films using a mixture of chlorine and argon gases is discussed.

Surface Emitting Semiconductor Lasers And Arrays, Gary A. Evans, Jacob M. Hammer

Electrical Engineering Research

No abstract provided.

Paschen's Law For A Hollow Cathode Discharge, H. Eichhorn, K. H. Schoenbach, T. Tessnow

Bioelectrics Publications

An expression for the breakdown voltage of a one‐dimensional hollow cathode discharge has been derived. The breakdown condition which corresponds to Paschen’s law contains, in addition to the first Townsend coefficient, and the secondary electron emission coefficient two parameters which characterize the reflecting action of the electric field and the lifetime of the electrons in the discharge. The breakdown voltage for a hollow cathode discharge in helium was calculated and compared to that of a glow discharge operating under similar conditions.

A Comparison Of Techniques For Time Delay Estimation, Aidan O'Dwyer

Conference papers

This paper reviews some of the techniques used for the identification of unknown lumped time delays in single input, single output (SISO) control systems and evaluates a number of these techniques in simulation and in implementation. Both off line and on line identification techniques are considered.

All-Optical Timing Extraction With Frequency Division Using A Twin-Section Laser Diode, Gerald Farrell, Paul Phelan, Joe Hegarty, J. Shields

Articles

All-optical timing extraction from a coded line signal with division of the extracted clock frequency is demonstrated using a single twin-section self-pulsating laser diode. Either the bit-rate clock or a submultiple of the bit-rate clock can be extracted, depending only on the DC biases applied to the self-pulsating laser diode. Timing extraction is carried out for the first time without optical injection locking of the self-pulsating laser diode by the optical data source

Design Of Distortion-Invariant Correlation Filters Using Supervised Learning, Samuel Peter Kozaitis, Rufus H. Cofer, Wesley E. Foor

Electrical Engineering and Computer Science Faculty Publications

We designed binary phase-only filters from a training set of images using a statistical approach. We forced images into clusters and designed filters to recognize objects from that cluster. We report on results obtained by computer simulation comparing the performance of filters to recognize objects from clusters of one and two classes.

Detection Of Skin Tumor Boundaries In Color Images, Fikret Erçal, M. Moganti, William V. Stoecker, Randy Hays Moss

Computer Science Faculty Research & Creative Works

A simple and yet effective method for finding the borders of tumors is presented as an initial step towards the diagnosis of skin tumors from their color images. The method makes use of an adaptive color metric from the red, green, and blue planes that contains information for discriminating the tumor from the background. Using this suitable coordinate transformation, the image is segmented. The tumor portion is then extracted from the segmented image and borders are drawn. Experimental results that verify the effectiveness of this approach are given

Reliability Trend Analyses With Statistical Confidence Limits Using The Luke Reliability Trend Chart, Stephen R. Luke

Engineering Management & Systems Engineering Theses & Dissertations

In electronic systems, it is interesting to understand exactly how the reliability is changing with time. Dynamic performance changes when a system passes from infant mortality stage into useful life phase and when the system passes from useful life phase into wearout phase. Dynamic performance also changes when the system is redesigned or when the system is acted on by a number of other outside forces such as a change in maintenance policy, escalation of alignment problems, or a change in training program. It is important to know when a system is changing dynamically in order to assess design, policy …

A Magnetic Suspension System With A Large Angular Range, Colin P. Britcher, Mehran Ghofrani

Mechanical & Aerospace Engineering Faculty Publications

In order to explore and develop technology required for the magnetic suspension of objects over large ranges of orientation, a small-scale laboratory system, the large-angle magnetic suspension test fixture (LAMSTF) has been constructed at NASA Langley Research Center. This apparatus falls into the category of large-gap, actively stabilized magnetic levitation systems. The hardware comprises five conventional electromagnets in a circular arrangement, each driven from a separate bipolar power amplifier. Electromagnet currents are commanded by a digital control system, implemented on a microcomputer, which in turn derives the position and attitude of the suspended element from an infrared optical system. The …

Photovoltaic-Powered Water Pumping-Design, And Implementation: Case Studies In Wyoming, Badrul H. Chowdhury, S. Ula, K. Stokes

Electrical and Computer Engineering Faculty Research & Creative Works

A photovoltaic-powered water pumping project comprising of several rural electric cooperatives and their customers is described in detail. A number of remote water pumping installations in the state of Wyoming, USA, are currently operating as a result of this project. The design, installation and performance monitoring of these systems are discussed. In general, it can be stated that PV-powered water pumping in this state has been a cost-effective alternative to distribution line extension or other conventional means of water pumping. Customer satisfaction, in terms of functional adequacy and low maintenance requirements of these systems, is high. The benefit for the …

Lightning Arrester Failure And Ferroresonance On A Distribution System, L. J. Bohmann, J. Mcdaniel, Eldon Keith Stanek

Electrical and Computer Engineering Faculty Research & Creative Works

Since 1987 the Upper Peninsula Power Company (UPPCO) has been experiencing a large number of lightning arrester failures on a portion of their distribution system in southern Marquette County, Michigan. It was in the area of the Navy's Extremely Low Frequency (ELF) antenna where the distribution system had been recently reconfigured so that the transformers were connected line-to-line in order to eliminate interference from the antenna. A study was done which determined that the system was susceptible to ferro resonance during single line faults under lightly loaded conditions and that the overvoltage's experienced could be causing the lightning arrester failures. …

Advanced Graphics Zoom In On Operations, Max Darwin Anderson, Hardy J. Pottinger, C. M. Schroeder

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Efficient Simulation Of Multicarrier Digital Communication Systems In Nonlinear Channel Environments, Kevin W. Schneider, William H. Tranter

Electrical and Computer Engineering Faculty Research & Creative Works

The effectiveness of computer simulation as a tool for the design and analysis of communication systems is often limited by the long execution times required for many simulations. When simulating multicarrier digital communication systems operating over nonlinear channels, the required high sampling rate contributes significantly to long execution times. A new method that reduces the sampling rate of simulations of such systems is developed. This Partial Sum of Products (ParSOP) method reduces the sampling rate by generating only the intermodulation products that lie in a frequency band of interest. The ParSOP method requires that the bandpass nonlinearity be represented by …

An Optoelectronic Implementation Of The Adaptive Resonance Neural Network, Donald C. Wunsch, T. P. Caudell, R. J. Marks, R. A. Falk, C. David Capps

Electrical and Computer Engineering Faculty Research & Creative Works

A solution to the problem of implementation of the adaptive resonance theory (ART) of neural networks that uses an optical correlator which allows the large body of correlator research to be leveraged in the implementation of ART is presented. The implementation takes advantage of the fact that one ART-based architecture, known as ART1, can be broken into several parts, some of which are better to implement in parallel. The control structure of ART, often regarded as its most complex part, is actually not very time consuming and can be done in electronics. The bottom-up and top-down gated pathways, however, are …

Use Of Storage Elements As Primitives For Modeling Faults In Synchronous Sequential Circuits, Waleed K. Al-Assadi, Y. K. Malaiya, A. P. Jayasumana

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Neural Networks In The Former Soviet Union, Donald C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Faulty Behavior Of Storage Elements And Its Effects On Sequential Circuits, Waleed K. Al-Assadi, Y. K. Malaiya, A. P. Jayasumana

Electrical and Computer Engineering Faculty Research & Creative Works

It is often assumed that the faults in storage elements (SEs) can be modeled as output/input stuck-at faults of the element. They are implicitly considered equivalent to the stuck-at faults in the combinational logic surrounding the SE cells. Transistor-level faults in common SEs are examined here. A more accurate higher level fault model for elementary SEs that better represents the physical failures is presented. It is shown that a minimal (stuck-at) model may be adequate if only modest fault coverage is desired. The enhanced model includes some common fault behaviors of SEs that are not covered by the minimal fault …

Design And Construction Of Maintainable Knowledge Bases Through Effective Use Of Entity-Relationship Modeling Techniques, William Yancey Pike

Retrospective Theses and Dissertations

The use of an accepted logical database design tool, Entity-Relationship Diagrams (E-RD), is explored as a method by which conceptual and pseudo-conceptual knowledge bases may be designed. Extensions to Peter Chen's classic E-RD method which can model knowledge structure used by knowledge-based applications are explored. The use of E-RDs to design knowledge bases is proposed as a two-stage process. In the first stage, and E-RD, termed the Essential E-RD, is developed of the realm of the problem or enterprise being modeled. The Essential E-RD is completely independent of any knowledge representation model (KRM) and is intended for the understanding of …

Automatic Color Segmentation Algorithms-With Application To Skin Tumor Feature Identification, Scott E. Umbaugh, Randy Hays Moss, William V. Stoecker, G. A. Hance

Electrical and Computer Engineering Faculty Research & Creative Works

Two color-image segmentation methods are described. The first is based on a spherical coordinate transform of original RGB data. The second is based on a mathematically optimal transform, the principal components transform (also known as eigenvector, discrete Karhunen-Loeve, or Hotelling transform). These algorithms are applied to the extraction from skin tumor images of various features such as tumor border, crust, hair scale, shiny areas, and ulcer. The results of this research will be used in the development of a computer vision system that will serve as the visual front-end of a medical expert system to automate visual feature identification for …

Semi-Insulating Polysilicon Hetero- And Isotype Junctions On Silicon, R. M. Ranade, S. S. Ang, W. D. Brown

Journal of the Arkansas Academy of Science

The effects of nitrogen trifluorideinthe gas stream during deposition of semi-insulating polysilicon (SIPOS) on the electrical characteristics of undoped (SIPSO)/p-Si, and n+-SIPOS/n-Si isotype junctions were investigated. The current-voltage characteristics of undoped SIPOS/p-Si heterojunctions exhibit a strong dependence on the oxygen content of the SIPOS film and depart from a hyperbolic sine behavior as the refractive index of the SIPOS increases.. The addition of nitrogen trifluoride decreases the current density of these undoped SIPOS/p-Si heterojunctions due presumably to the oxidation/hydrolysis of SiF species intoSiO2. The n+-SIPOS formed a rectifying isotype junction o n-Si. The forward current voltage characteristics exhibit two distinct …

Temporal Development Of Electric Field Structures In Photoconductive Gaas Switches, K. H. Schoenbach, J. S. Kenney, F.E. Peterkin, R. J. Allen

Bioelectrics Publications

The temporal development of the electric field distribution in semi‐insulating GaAs photoconductive switches operated in the linear and lock‐on mode has been studied. The field structure was obtained by recording a change in the absorption pattern of the switch due to the Franz–Keldysh effect at a wavelength near the band edge of GaAs. In the linear mode, a high field layer develops at the cathode contact after laser activation. With increasing applied voltage, domainlike structures become visible in the anode region and the switch transits into the lock‐on state, a permanent filamentary electrical discharge. Calibration measurements show the field intensity …

Superheating Of Bi(0001), E. A. Murphy, H. E. Elsayed-Ali, J. W. Herman

Electrical & Computer Engineering Faculty Publications

Superheating of Bi(0001) by about 90 K above the bulk melting temperature is observed using time-resolved reflection high-energy electron diffraction with ∼200-ps time resolution. Larger temperature excursions above the bulk melting temperature result in melting accompanied by irreversible laser damage to the surface. The rhombohedral structure of Bi leads to very different behavior of material parameters upon melting as compared with fcc metals. Therefore, our observation of the superheating of Bi(0001), together with the previously observed superheating of Pb(111), suggests the generality of the superheating phenomenon.

Direct Measurements Of The Transport Of Nonequilibrium Electrons In Gold Films With Different Crystal Structures, T. Juhasz, H. E. Elsayed-Ali, G. O. Smith, C. Suárez, W. E. Bron

Electrical & Computer Engineering Faculty Publications

The transport of femtosecond-laser-excited nonequilibrium electrons across polycrystalline and single-crystalline gold films has been investigated through time-of-flight measurements. The thicknesses of the films range from 25 to 400 nm. Ballistic electrons as well as electrons interacting with other electrons and/or with the lattice have been observed. The ballistic component dominates the transport in the thinner films, whereas the interactive transport mechanism is dominant at the upper end of the thickness range. A slower effective velocity of the interactive component is observed in the polycrystalline samples, and is assumed to arise from the presence of grain boundaries. The reflection coefficient of …

Design And Implementation Of Fuzzy Logic Controllers. Thesis Final Report, 27 July 1992 - 1 January 1993, Osama A. Abihana, Oscar R. Gonzalez

Electrical & Computer Engineering Faculty Publications

The main objectives of our research are to present a self-contained overview of fuzzy sets and fuzzy logic, develop a methodology for control system design using fuzzy logic controllers, and to design and implement a fuzzy logic controller for a real system. We first present the fundamental concepts of fuzzy sets and fuzzy logic. Fuzzy sets and basic fuzzy operations are defined. In addition, for control systems, it is important to understand the concepts of linguistic values, term sets, fuzzy rule base, inference methods, and defuzzification methods. Second, we introduce a four-step fuzzy logic control system design procedure. The design …

A New Technique To Decompose Closely Spaced Interface And Bulk Trap States Using Temperature Dependent Pulse-Width Deep Level Transient Spectroscopy Method: An Application To Pt/Cds Photodetector, C. W. Wang, Cheng-Hsiao Wu, Jack L. Boone

Electrical and Computer Engineering Faculty Research & Creative Works

A novel method is presented here to experimentally decompose nonexponential capacitive transients into the appropriate components from the closely spaced deep trap states. Using temperature dependent pulse-width deep level transient spectroscopy (TDP-DLTS) technique, we show for the first time that two bulk trap states and one continuously distributed interface states in (Pt/CdS) photodiodes can be successfully separated. The basic principle is to set the applied pulse width to follow an averaged temperature-dependent capture time constant and divide the DLTS spectrum. In the example of Pt/CdS photodiodes, we show that all physical parameters including thermal activation energies, capture cross sections, and …

Artificial Intelligence Applied To Detection Of Melanoma, Arve Kjoelen, Scott E. Umbaugh, William V. Stoecker, Randy Hays Moss

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

A Spectral Flux Method For Solving The Boltzmann Equation, Muhammad A. Alam, Mark A. Stettler, Mark S. Lundstrom

Department of Electrical and Computer Engineering Faculty Publications

A spectral method for solving the Boltzmann equation by the scattering matrix approach is presented, The algorithm discussed can be used to simulate both bulk and device properties with arbitrary field profiles. Although the primary goal is to reduce the data storage problem of the scattering matrix approach, many of the concepts and mathematical properties developed may be useful for other traditional spectral methods as well.