Electrical and Computer Engineering Commons^™

Static I-V Curve And Aging Test For Pim Characterization In Metallic Contacts, Kalkidan Anjajo

Masters Theses

"Spring clips and fabric-over-foams (FOFs) are widely used in mobile devices for electrical connection purposes. However, the imperfect metallic connections tend to induce passive intermodulation (PIM), resulting in a receiver sensitivity degradation, known as RF desensitization. Due to the complexity of the PIM characterization, there is not yet a way to evaluate PIM performance using a simple setup for environments like factories. In this study, a current-voltage (I-V) behavior-based PIM evaluation method is proposed and validated with various metallic contacts and contact forces. The test results demonstrated the feasibility of the PIM performance evaluation based on the measured static I-V …

Predicting Radiated Emissions From A Cable Harness Through Component Level Tests, Fuwei Ma

Masters Theses

“In this work, a procedure is developed to predict the radiated emissions from a cable harness using component-level tests. Direct measurement on the engine control unit is utilized to accurately characterize the equivalent common mode source voltages and impedance associated with the device. The cable harness geometry is reduced using the equivalent cable bundle approach by lumping wires according to the source and load impedance compared with characteristic impedance of the harness, which dramatically reduces the measurement effort and allows practical 3D full-wave simulation of the radiated emissions. Radiated emissions are predicted from an engine control unit (ECU) and an …

Numerical Investigations Of 2-D Magnetic Nozzles On Pulsed Plasma Plumes, Joshua Daniel Burch

Masters Theses

"This research presents studies of a novel type of magnetic nozzle that allows for three-dimensional (3-D) steering of a plasma plume. Numerical simulations were performed using Tech-X's USim® software to quantify the nozzle's capabilities. A2-D planar magnetic nozzle was applied to plumes of a nominal pulsed inductive plasma (PIP) source with discharge parameters similar to those of Missouri S&T's Missouri Plasmoid Experiment (MPX). Argon and xenon plumes were considered. Simulations were verified and validated through a mesh convergence study as well as comparison with available experimental data. Periodicity was achieved over the simulation run time and phase angle samples were …

Analysis Of Electromagnetic Interference Problems Causedbyhigh-Speed Multiplayer Boards With Split Referenceplane, Xin Fang

Masters Theses

"Digital/Analog ground partitioning has been used to isolate noisy digital and power current from sensitive analog currents in high-speed multiplayer printed circuit boards. The through-hole signal via enables convenient routing and component placement on the PCB and is used for signal interconnections when the signal traces are changing the layers. This design, however, breaks the current return path for signal traces that cross the two separated grounds, which causes undesired effects such as signal distortion and radiated emission.

Electromagnetic mechanism associated with them needs to be understood to control and suppress these undesired effects. In this paper, we have investigated …

Automatic Sparse Esm Scan Using Gaussian Process Regression, Jiangshuai Li

Masters Theses

“Emission source microscopy (ESM) technique can be utilized for localization of electromagnetic interference sources in complex and large systems. In this work a Gaussian process regression (GPR) method is applied in real-time to select sampling points for the sparse ESM imaging using a motorized scanner. The Gaussian process regression is used to estimate the complex amplitude of the scanned field and its uncertainty allowing to select the most relevant areas for scanning. Compared with the randomly selected samples the proposed method allows to reduce the number of samples needed to achieve a certain dynamic range of the image, reducing the …

State Level Trends In Renewable Energy Procurement Via Solar Installation Versus Green Electricity, Eric Michael Hanson

Masters Theses

“In the past 5 years, consumer options for procuring renewable energy have increased, ranging from rooftop solar installation to utility green pricing to Community Choice Aggregation. These options vary in terms of costs and benefits to the consumer as well as grid integration implications. However, little is known regarding how the presence of a wide range of options for utility-scale renewable procurement affects demand for distributed residential solar installations. In theory, there are three possible relationships, (1) positive correlation, where utility-scale and distributed resources complement each other to increase overall production, (2) negative correlation, where utility-scale and distributed resources are …

Optimization And Modeling Of Esd Protection Devices, Li Shen

Masters Theses

“Transient voltage suppressors (TVS) are used to protect ICs (integrated circuits) against overvoltage, ESD (Electrostatic Discharge), inductive load switching, and even lightning strikes. In this research, a transient behavior model framework for ESD protection devices is used for modelling four different types of TVS (non-snapback, snapback, spark gap like device and varistor). The System-Efficient ESD Design (SEED) methodology is utilized to strengthen the trust in the model framework by efficient simulation of ESD interaction of the off-chip ESD protection devices with the IC ESD protection device and associated measurement data.

Improvements in the TVS transient response, accounting for conductivity modulation, …

Development Of A Highly Sensitive Pressure Sensing System With Custom-Built Software For Continuous Physiological Measurements, Masoud Panahi

Masters Theses

In this work, a pressure sensing system was designed and fabricated by developing a highly sensitive cone-structured pressure sensor with a custom-built software for physiological monitoring applications. A novel highly sensitive cone structured porous polydimethylsiloxane (PDMS) based pressure sensor capable of detecting very low-pressure ranges was developed for respiration monitoring. The pressure sensor was fabricated using a master mold, a hybrid-structured dielectric layer, and fabric-based electrodes. The master mold with inverted cone structures was created using a rapid and precise three-dimensional (3D) printing technique. The dielectric layer, with pores and cone structures, was prepared by annealing a mixture of PDMS, …

The Field Coupling Mechanism Study For Near Field Probe, Shun Liu

Masters Theses

"In this part, the radius of the loop is used to predict the voltage induced by the E- field in the circular loop antenna. The thin rectangle loop and thick rectangle loop have been investigated. The equivalent radius of the rectangle loop is estimated by the average of the one over the distance between the points on the loop to the center of the loop. The estimation matches with the numerical simulation"--Abstract, page iv.

A Simple Background Elimination Method For Miniaturized Fiber-Optic Raman Probe, Bohong Zhang

Masters Theses

"Raman scattering is called a photonic - molecular interaction based on the kinetic model of the analytic. Due to the uniqueness of the Raman scattering technique, it can provide a unique fingerprint signal for molecular recognition. However, a serious challenge often encountered in Raman measurement comes from the requirements of fast, real-time remote sensing, background fluorescence suppression, and micro-environmental detection.

A new Miniaturized Fiber-Optic Raman Probe (MFORP) for Raman spectroscopy, used especially for eliminating background fluorescence and enhancing sampling, is presented. Its main purpose is to provide an overview of excellent research on the detection of very small substances and …

Method Of Optimal Battery Scheduling With Optimal Battery And Photovoltaic Sizing, Gideon Hallman

Masters Theses

“Renewable energy generation is on the rise. One of the best ways to capitalize on this intermittent power supply is by using the renewable energy source in tandem with batteries. A joint photovoltaic (PV) and battery system model was created that implemented battery degradation and optimized battery usage using a Markov Decision Process (MDP). This system was then subjected to a series of tests to do a sensitivity analysis while optimizing the battery and PV sizing for the system at hand. Parametric sweeps of solar power and battery capital costs, the cost of energy taken from the grid, the cost …

A Physics-Based Pi Pre-Layout Tool For Pcb Pdn Design, Shuang Liang

Masters Theses

"With increasingly stringent requirements for lower voltage supply, and higher density in PCB PDN design, now integrity (PI) is an increasingly important aspect that must be considered. A pre-layout tool based on the Cavity Model and Boundary Element Method is built to automatically achieve a specified target impedance for a multi-layered Printed Circuit Board (PCB) Power Distribution Network (PDN) design with a minimal number of decoupling capacitors.

The pre-work about the post-layout design and analysis is proposed and the guidelines for creating a decoupling capacitors network with better performance has been built. With limit inputs, physical limitations for the minimal …

Design And Evaluation Of The 3d Printed Electromagnetic Absorber Built With Conductive Carbon-Filled Filament, Rui Mi

Masters Theses

"This research presents an application of the resistive frequency selective surface (FSS) fabricated with a 3D printed conductive material as an electromagnetic absorber for the EMI-reducing door. This solution allows to reduce radiated emissions of a router system. The resistive frequency selective surface has a three-layer structure. The top layer is a 3D printed FSS pattern, the middle layer is an air gap, and the bottom layer is a metal plane.

The first paper presents the methodology for manufacturing a frequency selective surface using the 3D printing technology, including the material characterization, design, fabrication, and evaluation.

The unpublished content presents …

Transfer Function Measurement For Automotive Intentional Emi And Thermal Runaway Investigation Of Lithium-Ion Battery By Intentional Emi, Woncheol Song

Masters Theses

"With an increasing demand for electric vehicles and autonomous driving, many components of a vehicle are being replaced as electric components. This implicates the possibility of an increase in the malfunction of electric components due to unknown electromagnetic interferences. In this reason, malicious intentional electromagnetic interference (IEMI) is being considered as a growing threat for the current and next generation of automotive technology.

In the first topic, the transfer function between the IEMI attacker and the engine control unit (ECU) circuit in an automobile is extracted to analyze how the IEMI affects the vehicle.

In the second topic, to mimic …

Bond Graph Modeling Of Critical Infrastructures For Cyber-Physical Security Implementation, Michele Jane White

Masters Theses

“In developed societies, there exists infrastructure vital to everyday life. This includes water and power systems. Technology is quickly evolving and being implemented on these utilities. This technology can range from smart metering in neighborhoods to volume sensors in local waste water treatment facilities. When networking, sensing, monitoring, or control devices are integrated with infrastructure it is considered a cyber physical system, or CPS. When information about an important physical system is connected to the virtual world, it is opened up to security risks. Cyber security can be provided to the CPS by monitoring the physical state of the system …

A Compact Wavelength Meter Using A Multimode Fiber, Ogbole Collins Inalegwu

Masters Theses

“Wavelength meters are very important for precision measurements of both pulses and continuous-wave optical sources. Conventional wavelength meters employ gratings, prisms, interferometers, and other wavelength-sensitive materials in their design. Here, we report a simple and compact wavelength meter based on a section of multimode fiber and a camera. The concept is to correlate the multimodal interference pattern (i.e., speckle pattern) at the end-face of a multimode fiber with the wavelength of the input lightsource. Through a series of experiments, specklegrams from the end face of a multimode fiber as captured by a charge-coupled device (CCD) camera were recorded; the images …

Analysis And Design Of Dc-Link Capacitor In Cascaded H-Bridge Multilevel Active Front-End Converter, Muhammad Shehroz Malik

Masters Theses

Medium-voltage grid-tied systems often use a cascaded H-bridge multi-level active front-end. In this converter, dc link bus capacitors play an important role in stabilizing the converter and enabling both active and reactive power injections. The present work provides analytical expressions for the capacitor current, which are essential for optimizing system design (especially capacitor size vs. lifetime). Then, the expression is incorporated into the grid connected bidirectional power system model. Consequently, this work contributes to the guiding principles to choose accurate dc link capacitor ratings against grid-side power delivery requirements.

DC-link capacitors come with an expiration date which is dependent on …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Seed Modeling Of An Esd Gun Discharge To A Usb Cable, Yang Xu

Masters Theses

“An IC protected by a transient voltage suppression (TVS) diode may fail if the TVS device does not turn on or does not turn on quickly enough, causing the IC to take the full brunt of the electrostatic discharge (ESD) event. Transient simulation models have been developed for ESD protection devices for the purpose of system-efficient ESD design (SEED). The TVS modeling methodology has been improved to better represent the physics that occurs during the TVS response and more accurately predict the interactions between off-chip and on-chip protection devices. Moreover, a complicated test scenario -- an ESD gun discharge through …

A Framework To Support Automatic Certification For Self-Adaptive Systems, Ioannis Nearchou

Masters Theses

Presently, cyber-physical systems are increasingly being integrated into societies, from the economic sector to the nuclear energy sector. Cyber-physical systems are systems that combine physical, digital, human, and other components, which operate through physical means and software. When system errors occur, the consequences of malfunction could negatively impact human life. Academic studies have relied on the MAPE-K feedback loop model to develop various system components to satisfy the self-adaptive features, such that violation of the safety requirements can be minimized. Assurance of system requirement satisfaction is argued through an industrial standard form, called an assurance case, which is usually applied …

Flexible Capacitive Pressure Sensors And Triboelectric Energy Harvesters Using Laser-Assisted Patterning Process For Flexible Hybrid Electronic Applications, Valliammai Palaniappan

Masters Theses

This work focuses on the design, fabrication and characterization of novel flexible capacitive pressure sensors and triboelectric energy harvesters using laser-assisted patterning process for flexible hybrid electronic applications. Initially, the capacitive pressure sensor was developed by fabricating a set of polydimethylsiloxanes (PDMS) dielectric films with pyramid shaped micro-structures using a laser-assisted patterning process. The pressure sensor consists of two electrodes (top and bottom) that were fabricated by depositing silver (Ag) on flexible polyethylene terephthalate (PET) using additive screen-printing process. Finally, the pressure sensor was assembled by attaching the top and bottom Ag electrodes to the smooth side of pyramid shaped …

Optimized System For On-Route Charging Of Battery Electric Buses And High-Fidelity Modelling And Simulation Of In-Motion Wireless Power Transfer, Yogesh Bappasaheb Jagdale

Masters Theses

Electrifying cars, buses and trucks is an attractive means to reduce energy use and emissions, because it involves minimal restructuring of the transportation network. Transit buses drive fixed routes, minimizing driver range anxiety by properly sizing energy storage system but the major challenge to fully electrifying transit buses, is the amount of energy they consume in a day of driving. To enable a full day of operation, batteries need to be large, which is expensive and heavy. This work utilizes real-world transit bus data fed to a battery electric drive-train model to co-optimize charger locations, charger power levels, and vehicle …

Passive And Active Battery Balancing Methods Implemented On Second Use Lithium-Ion Batteries, Walter Bartek

Masters Theses

As the number of electric vehicles (EVs) increases, the number of used battery packs that require disposal increases; however, many of these packs still have useful capacity and can be repurposed. When using repurposed large lithium-ion battery packs, deviations between cells within a pack become problematic. These deviations result in a pack that is unbalanced, affecting performance and proving potentially hazardous when charging. Consequently, a battery management system (BMS) is needed. To provide safety, the BMS in this paper monitors and controls the operation of the battery pack. In addition, it controls the redistribution of charge between the cells within …

Vehicle Velocity Prediction Using Artificial Neural Networks And Effect Of Real-World Signals On Prediction Window, Tushar Dnyaneshwar Gaikwad

Masters Theses

Prediction of vehicle velocity is essential since it can realize improvements in the fuel economy/energy efficiency, drivability, and safety. Many publications address velocity prediction problems, yet there is a need for the understanding effect of different signals for the prediction. There are numerous new sensor and signal technologies like vehicle-to-vehicle and vehicle-to-infrastructure communication that can be used to obtain comprehensive datasets. Several references considered deterministic and stochastic approaches that use the datasets as input to determine future operation predictions. These approaches include different traffic models and artificial neural networks such as Markov chain, nonlinear autoregressive model, Gaussian function, and recurrent …

Design And Development Of Power Processing Units For Applications In Electrically-Propelled Satellite Systems, Kartikeya Jayadurga Prasad Veeramraju

Masters Theses

"Electrospray technology provides a way to ionize specialized liquids by applying high voltages across a sharp porous tip and a metallic mesh. This technology is widely used in the field of mass spectroscopy for generating ions for testing purposes. The dawn of nano-satellites posed new challenges in the miniaturization of many conventional satellite sub-systems. One significant challenge faced in such a process was the miniaturization of the propulsion system. Electrosprays have started to find their application in the field of Aerospace Engineering and now are formally known as Electrospray Thrusters. These thrusters provide high specific impulse and are attractive substitutes …

Serdes Channel Crosstalk Mitigation Methodology With Industrial Implementation Guidance, Junda Wang

Masters Theses

"With the increasing data rate of digital circuits, the differential crosstalk degrades the signal integrity performance in PCBs drastically. Usually, in the trace area, crosstalk can be isolated by stitching vias and adding shielding ground vias can also shield coupling in the ball gate array (BGA) and pin field area. The traditional way to mitigation crosstalk in the BGA and pin field area through adding more ground vias between signal pairs or increasing the spacing in between, it demonstrated us the efficiency on crosstalk cancellation efficiency but it also increases the size of products and it would be contradictory to …

Modeling And Control Of Cascaded Bridgeless Multilevel Rectifier Under Unbalanced Load Conditions, Sai Hemanth Kankanala

Masters Theses

“The goal of this project is to model and control a novel unidirectional cascaded multilevel bridgeless rectifier as an active front end in medium and high voltage applications. This topology has many advantages over a conventional cascaded H-bridge rectifier, such as lower implementation cost, higher reliability, and greater flexibility with similar power quality. The complete design process of the proposed converter is developed step by step in order to meet all the desired objectives. The steady-state mathematical model is used to develop a method for the voltage balancing of dc cells. Power factor analysis is discussed to mathematically derive requirements …

Design And Comparison Of Unoptimized And Optimized Gray Code Multi-Level Systems, Shirly Adams Gamliel

Masters Theses

“As the conventional binary MOS-based VLSI technology is reaching limitations in chip area, speed, and power, new technologies are being researched. Some such technologies relate to multi-level logic design. This thesis explores the process and benefits of applying and optimizing multi-level design techniques to an existing Gray code binary system. Specifically, the multi-level system is designed using CoreMem technology and is optimized using Indira Dugganapally’s optimization techniques.

The first step is generating the n-bit binary and quaternary truth tables for an encoder’s Gray code output and additional desired data. Then, the data for each n-bit system is arranged in multi-level …

Portable Electrochemical System For Flexible Hybrid Electronics, Anthony Joseph Hanson

Masters Theses

This work focuses on the fabrication and design of a portable electrochemical sensing system for flexible hybrid electronic (FHE) sensors. A three-electrode chemical sensor was fabricated using copper tape on polyethylene terephthalate (PET) substrate, using laser etching process. An electronic circuit was designed to measure the sensor response through electrochemical techniques to detect different concentrations of glucose. The device was calibrated to give the user a concentration value in 5 seconds. The system was also designed to preform tests such as cyclic voltammogram and chronoamperogram for various chemicals. A Bluetooth Low Energy module was used to wirelessly transmit the results …

Intracellular Electrometer, Lucas M. Essenburg

Masters Theses

The Western Michigan University Neurobiology Engineering Laboratory conducts re- search in energy-efficient electrical stimulation of biological neurons. Experimental work re- quires an intracellular electrometer to inject nanoamp-level currents into a biological neuron and to measure its membrane voltage response. In order to fully understand the generation of such minute currents, an `in-house' electrometer was designed, constructed, and validated. This required exploration of various design trade-offs including precision of generated nanoamp-level currents vs. susceptibility to noise, portability vs. functionality, and cost vs. functionality. The electrometer was successfully used to stimulate and measure responses of neurons from the medicinal leech Hirudo verbana …