Electrical and Computer Engineering Commons^™

Transparent Spectrum Co-Access In Cognitive Radio Networks, Jonathan Daniel Backens

Electrical & Computer Engineering Theses & Dissertations

The licensed wireless spectrum is currently under-utilized by as much as 85%. Cognitive radio networks have been proposed to employ dynamic spectrum access to share this under-utilized spectrum between licensed primary user transmissions and unlicensed secondary user transmissions. Current secondary user opportunistic spectrum access methods, however, remain limited in their ability to provide enough incentive to convince primary users to share the licensed spectrum, and they rely on primary user absence to guarantee secondary user performance. These challenges are addressed by developing a Dynamic Spectrum Co-Access Architecture (DSCA) that allows secondary user transmissions to co-access transparently and concurrently with primary …

Characterization Of An Impulse Radiating Antenna In The Near Field, Chandra Barjracharya

Electrical & Computer Engineering Theses & Dissertations

The biological effects of intense sub-nanosecond pulses on tissues or cells are in the dielectric domain and not based on thermal loading as in the conventional microwave radiation, which may lead to an entirely new approach of modifying cell functions. Moreover, the resulting cell functional change may be detected with higher resolution by broadband, sub-nanosecond pulses than conventional narrowband systems. The delivery of intense sub-nanosecond pulses to near-field biological tissues, however, has not been studied, not mentioning the focal depth and volume. In this dissertation, for the first time, an impulse radiating antenna with a balanced feed structure is studied …

Generation Of Bipolar Nanosecond Pulses, Sambasiva Rao Rajulapati

Electrical & Computer Engineering Theses & Dissertations

Bipolar pulse generation has been studied using transmission line technology, which was mainly used for monopolar pulse generation. In this thesis, low impedance, high current, nanosecond pulse generators were designed, constructed and tested. Five transmission lines were connected in parallel, so the impedance was 10 n. The transmission lines were switched by a spark gap switch operated in air. The closing of the switch creates a matched condition on one side of the transmission lines and a short circuit on the other side of the transmission lines. When the transmission lines are precharged, one of the two waves in opposite …

Synthesis Of Nanolaminate Structures Of Alternating Layers Of Lead Telluride And Lead Selenide By Atomic Layer Deposition For Thermoelectric Applications, Arun Deepak Ramalingom Pillai

Electrical & Computer Engineering Theses & Dissertations

Alloys composed of lead, telluride and selenide compounds exhibit very high figure of merit ZT values at intermediate temperatures, making them exceptional thermoelectric materials in a particular temperature range. Advancement in thermoelectric devices and applications hinges on increasing ZT, which is a ratio of the thermoelectric power factor to the thermal conductivity. One of the proposed avenues to achieving this goal is the use of low dimensional structures such as quantum wells, quantum dots, superlattices (SL) and nanolaminates to affect heat transport. SL structures can effectively confine charge carriers as well as scatter phonons which contribute significantly to thermal conductivity. …

Ionizing Radiation Detection Using Microstructured Optical Fiber, Stanton Dehaven

Electrical & Computer Engineering Theses & Dissertations

Ionizing radiation detecting microstructured optical fibers are fabricated, modeled and experimentally measured for X-ray detection in the 10-40 keV energy range. These fibers operate by containing a scintillator material which emits visible light when exposed to ionizing radiation. An X-ray source characterized with a CdTe spectrometer is used to quantify the X-ray detection efficiency of the fibers. The solid state CdTe detector is considered 100% efficient in this energy range. A liquid filled microstructured optical fiber (MOF) is presented where numerical analysis and experimental observation leads to a geometric theory of photon transmission using total internal reflection. The model relates …

Detection Of Ofdm Signals Using Pilot Tones And Applications To Spectrum Sensing For Cognitive Radio Systems, Ahmed Temtam

Electrical & Computer Engineering Theses & Dissertations

Nowadays there are an increasing number of wireless devices which support wireless networking and the need for higher data rate communication is increasing rabidly. As more and more systems go wireless, approaching technologies will face spectral crowding and existence of wireless devices will be an important issue. Because of the limited bandwidth availability, accepting the request for higher capacity and data rates is a challenging task, demanding advanced technologies that can offers new methods of using the available radio spectrum. Cognitive radio introduces a key solution to the spectral increasing issue by presenting the opportunistic usage of spectrum that is …

Photovoltaic Tracker Optimization With Unique Fault Detection And Enhanced Combiner System, Caitlin Nicole Conway

Electrical & Computer Engineering Theses & Dissertations

Renewable energy resources are rapidly becoming extremely important as the world's energy consumption continues to rise. The most popular of these resources is solar energy and more specifically photovoltaic energy. Currently, solar modules on the market are still not highly efficient. In order to increase the productivity of solar energy systems, larger fixed-panel photovoltaic systems or tracking photovoltaic systems are utilized. The major disadvantage of larger photovoltaic systems is the increased space requirements. Therefore, tracking photovoltaic systems are the best alternative to achieve higher solar energy yields.

To date, the only method of monitoring tracking photovoltaic systems is with the …

Control System Of An Atomic Layer Deposition (Ald) Machine, Nitin Vishnu Hegde

Electrical & Computer Engineering Theses & Dissertations

Atomic Layer Deposition is one of the most efficient deposition processes for obtaining ultrathin films. The deposition by this process happens one atomic layer at a time. ALD is known for its precision and ability to develop quality films with great thickness control. ALD machines simultaneously control DC and AC currents, low pressure operations, temperature control and heating (up to 500'C), precision flow control, precision timing intervals for deposition (milli-second intervals) and constantly monitor temperature. Such a high control comes at a high price. Furthermore, at the university level, the capacity to modify or enhance a machine is critical but …

Synthesis And Optimization Of Vo₂ Thin Films For Phase Transition Applications By Atomic Layer Deposition And Rf Magnetron Sputtering, Madhavi Tangirala

Electrical & Computer Engineering Theses & Dissertations

Among many Vanadium oxides and suboxides, VO₂ has received considerable attention due to its remarkable metal-insulator transition (MIT) or semiconductor-metal transition (SMT) behavior, a reversible change in its electrical and optical properties that occurs due to a phase transition near a temperature of 68°C. Electrically, the resistivity of VO₂ can be changed as large as 4-5 orders of magnitude. Optically, the transmittance drops dramatically above the transition temperature in the metallic state where the VO₂ film becomes highly reflective in the infrared region. All these properties result in structural phase transformation from a low temperature monoclinic to …

Identifiability Of Additive, Time-Varying Actuator And Sensor Faults By State Augmentation, Jason M. Upchurch

Electrical & Computer Engineering Theses & Dissertations

Faults in dynamical systems can have serious safety and reliability implications. For example, actuator and sensor faults have been factors in past incidents and mishaps in many aerospace systems. A large body of research is devoted to developing methods to detect and identify actuator and sensor faults in such systems.

One fault detection and identification menthol employs state augmentation, whereby a set of time-varying faults of interest are modeled as outputs of exogenous linear, time-invariant systems and augmented to the state of the nominal system model. The resulting model represents the system dynamics due to a particular actuator-sensor fault configuration. …

Optimization Of Solar Cell Arrays Using The Fibonacci Search Algorithm, Felicia Tyyan Farrow

Electrical & Computer Engineering Theses & Dissertations

In our energy hungry world, there is a growing demand to develop creative mechanisms to extract, conserve, and use energy from different resources. The use of solar cells to extract and convert solar energy into electrical energy is a growing and popular field of study because solar energy is clean, free, and renewable. One limitation for photovoltaic (PU) or solar technology is its loss in efficiency and availability as a result of shading or partial shading. Shading or partial shading decreases the total capable output power that the PV system can produce because the array is receiving irradiation from the …

Improving The Efficiency Of P3ht:Icba Organic Solar Cells By Modifying The Photoactive Solution Preparation Step, Matthew Blaine Samson

Electrical & Computer Engineering Theses & Dissertations

Organic solar cells (OSCs) are a promising alternative to conventional silicon solar cells. These organic devices offer the promise of facile low cost large scale solution based processing on lightweight, flexible, plastic substrates. At the present state of the technology, however, OSCs exhibit relatively low power conversion efficiencies. To improve these efficiencies, new materials are constantly being developed.

One such material is the fullerene indene-C₆₀ bisadduct (ICBA). When implemented in a poly(3-hexylthiophene-2, 5-diyl) (P3HT) : ICBA bulk heterojunction solar cell, these devices exhibit open circuit voltages exceeding 0.8 V, a value much higher than the devices made implementing phenyl-C …

Improving The Stability Of High And Low Bandgap Polymers Organic Photovoltaic Devices Using A Solution Based Titanium Sub-Oxide Interfacial Layer, Kurniawan Foe

Electrical & Computer Engineering Theses & Dissertations

The improvement in device efficiency has brought organic photovoltaic (OPV) devices closer to commercial viability, highlighting the importance of studying the lifetime and stability of OPV devices. At present, the lifetime and stability of OPV devices is much shorter and poor mainly caused by oxygen, moisture, and light resulting in the oxidation on low work function electrodes and the degradation of the morphology of the photoactive layer. To improve the lifetime and stability of the OPV devices, we used newly developed low bandgap polymer, PCDTBT, as the electron acceptor material and a solution based titanium sub-oxide (TiOx) interfacial layer inserted …

Study Of Spatiotemporal Signatures Between Objects To Improve Video Segmentation In Complex Environments, Adam Robert Reckley

Electrical & Computer Engineering Theses & Dissertations

Background subtraction is often considered to be a required stage of any video surveillance system being used to detect objects in a single frame and/or track objects across multiple frames in a video sequence. Most current state-of-the-art techniques for object detection and tracking utilize some form of background subtraction that involves developing a model of the background at a pixel, region or frame level and designating any elements that deviate from the background model as foreground. Most existing approaches are capable of segmenting a number of distinct components, but are unable to distinguish between the desired object of interest and …

Time Synchronization For Ofdm Transmission With Applications To 4g Wimax Wireless Systems, Hamad Alhajri

Electrical & Computer Engineering Theses & Dissertations

Orthogonal Frequency Division Multiplexing (OFDM) has recently gained a lot of attention as a promising new technology for Broadband Wireless Access. OFDM-based communication systems decompose a high rate data stream into a set of lower data rate streams that are transmitted simultaneously over multiple subcarriers. WiMAX is an efficient and reliable wireless transmission standard that employs OFDM transmission. Due to its flexibility and mobility, WiMAX is becoming a preferred air interface for next generation broadband wireless systems. OFDM systems, including WiMAX, are very sensitive to time offsets introduced by radio signal propagation between transmitters and receivers. The lack of time …

Impact Of Primary User Activity On The Performance Of Energy-Based Spectrum Sensing In Cognitive Radio Systems, Sara L. Macdonald

Electrical & Computer Engineering Theses & Dissertations

Increasing numbers of wireless devices and mobile data requirements have led to a spectrum shortage. However spectrum utilization percentages are often low due to the current static spectrum allocation process where primary users (PUs) are given exclusive use to spectrum. Several mechanisms to increase spectrum utilization have been proposed including opportunistic spectrum access (OSA). Cognitive Radio (CR) is an emerging concept in wireless communication systems that aims to enable OSA in licensed frequencies by secondary users (SUs). CR systems are expected to sense the spectrum in order to determine if the PU is transmitting. Therefore OSA performance relies on the …

Fast Transients In Non-Volatile Resistive Memories (Rram) Using Tantalum Pentoxide As Solid Electrolyte, Pragya Rasmi Shrestha

Electrical & Computer Engineering Theses & Dissertations

The semiconductor electronics industry has followed Moore's law austerely since 1965 fueling the microelectronics revolution and major technological advancements. Over the recent decades, the semiconductor industry has proven to be very successful, particularly by scaling the geometry of devices ever smaller. The device scaling has been very effective in boosting productivity yielding astonishing integration levels while simultaneously dramatically dropping the price per bit. However, the future of device scaling remains unclear. It is certain that device scaling will face severe reliability, cost and energy issues in the future. Therefore, there is a need to identify alternative technology platforms. Reconfigurable devices …

Investigation Of Nbnx Thin Films And Nanoparticles Grown By Pulsed Laser Deposition And Thermal Diffusion, Ashraf Hassan Farha

Electrical & Computer Engineering Theses & Dissertations

Niobium nitride films (NbNx) were grown on Nb and Si (100) substrates using pulsed laser deposition (PLD), laser heating, and thermal diffusion methods. Niobium nitride films were deposited on Nb substrates using PLD with a Q-switched Nd: YAG laser (λ = 1064 nm, 40 ns pulse width, and 10 Hz repetition rate) at different laser fluences, different nitrogen background pressures and deposition temperatures. The effect of changing PLD parameters for films done by PLD was studied. The seen observations establish guidelines for adjusting the laser parameters to achieve the desired morphology and phase of the grown NbNx films.

When the …

Fault Detection System For Solar Tracking Applications, Hareen Sekhar Illa

Electrical & Computer Engineering Theses & Dissertations

Oil, coal and natural gas reserves are being depleted faster than forecasted due to continued increase in demand for energy sources. We need, therefore, to develop renewable energy sources, such as solar, wind, biomass, geothermal, hydro power and tidal energy. In spite of having very high potential, harvesting solar energy has been a challenge because of the relatively low efficiency of solar cells. In the past few years different methods have been developed to increase the efficiency of the photovoltaic (PV) system: (I) improve the efficiency of solar cells (ill use a solar tracking system to increase the received solar …

Configuration Studies Of Electrostatic And Magnetostatic Active Space Radiation Shielding, Trac K. Nguyen

Electrical & Computer Engineering Theses & Dissertations

Developing successful and optimal solutions for mitigating the hazards of radiation in deep space is critical for the success of deep-space long duration explorations, including mission to the Moon, Mars and beyond. A recent report (Tripathi et al., 2008) had explored the feasibility of using electrostatic shielding in conjunction with state-of-the-art materials shielding technologies.

In this thesis research, we study the active electrostatic shielding strategy and examine a hybrid configuration that utilizes both electrostatic and magnetostatic fields. The main advantages of this system are shown to be: (i) much lower magnetic fields that could be below the thresholds set for …

Subnanosecond Exposure Systems For Biological Studies, Jongbong Nah

Electrical & Computer Engineering Theses & Dissertations

The research of bioelectrics has expanded to subnanosecond pulse region and entered a new domain of biophysics of cell interaction with ultra-short and intense electric fields. As subnanosecond pulses may be delivered by antennas to the human body and is very attractive to the medical community, the study of subnanosecond pulse effects calls for exposure systems for both cells and tissues. Two systems were designed in the scope of this thesis, used for cells and tissues respectively. The exposure system designed for cell exposure is a cuvette consisting of two parallel aluminum gaps. This cuvette is placed in a coaxial …

Nonthermal Plasma Jet Efficacy On Candida Kefyr, Amber Marie Mattson Jackson

Electrical & Computer Engineering Theses & Dissertations

The inactivation abilities of a nonthermal plasma jet were investigated with the yeast C. kefyr, a pathogen with increasing importance in healthcare. The plasma is generated using a microhollow cathode discharge (MHCD) geometry operated with a DC voltage of 2 kV and a current of 30 mA using air as the operating gas at an airflow rate of 8 SLM. The plasma discharge approaches room temperature at a few mm away from the plasma jet allowing for the use on heat sensitive surfaces. Dry air and humid air were used as the operating gas to see if humidity plays …

Modeling Leakage Currents In Metal Insulator Metal Structures With High K Materials, Priyamvada Maleeswaran

Electrical & Computer Engineering Theses & Dissertations

Various products such as personal computers, cellular phones and mobile devices require high speed and low power consumption. Such improvements have been attained by minimizing physical dimensions of electronic devices, leading to high density integration of transistors and capacitors on integrated chips (]Cs). However, as a consequence of down-scaling device dimensions, tunneling of electrons through thin gate oxides (SiO₂) increases, leading to increased static power leakage. This constitutes wastage in power, and for the case of memory applications necessitates faster refresh cycles. In order to overcome such issues, high-k materials (such as HfO₂ and ZrO₂) …

Dynamics Of Non-Thermal Plasma Jets Under Variable Pressure, Mehmet Arda Akman

Electrical & Computer Engineering Theses & Dissertations

Non-thermal plasma (NTP) jets driven by short DC pulses have attracted the attention of researchers within the past decade due to their promising bio-medical applications in the fields of wound healing, cancer treatment and sterilization. The ability to operate at atmospheric pressure, room temperature and simple device configuration has greatly contributed to their appeal and adoption in the plasma science community. However, the mechanisms that sustain the plasma generation and propagation in ambient air are currently a topic of debate. For instance, what appears as a continuous stream of a plasma plume extending outwards from a plasma device into the …

Performance Optimization Over Wireless Links With Operating Constraints, Shiny Abraham

Electrical & Computer Engineering Theses & Dissertations

Wireless communication is one of the most active areas of technological innovations and groundbreaking research ranging from simple cellular phones to highly complex military monitoring devices. The emergence of radios with cognitive capabilities like software defined radios has revolutionized modern communication systems by providing transceivers which can vary their output waveforms as well as their demodulation methods. This adaptability plays a pivotal role in efficient utilization of radio spectrum in an intelligent way while simultaneously not interfering with other radio devices operating on the same frequency band. Thus, it is safe to say that current and future wireless systems and …

Synthesis Of A Superlattice Structure Of Alternating Layers Of Antimony Telluride And Bismuth Telluride By Atomic Layer Deposition For Thermoelectric Applications, David Nminibapiel

Electrical & Computer Engineering Theses & Dissertations

Alloys composed of bismuth, antimony and telluride compounds exhibit very high figure of merit ZT values at relatively low temperatures, making them exceptional thermoelectric materials. Advancement in thermoelectric devices and applications hinges on increasing ZT, which is a ratio of the thermoelectric power factor to the thermal conductivity. One of the proposed avenues to achieving this goal is the use of low dimensional structures such as quantum wells, quantum dots, superlattices (SL) and nanolaminates to affect heat transport. SL structures can effectively confine charge carriers as well as scatter phonons which contribute significantly to thermal conductivity. In this thesis, the …

Diamond This Film Patterning Technique Using Selective Nucleation Growth, Characterization And Application, Weican Xiao

Electrical & Computer Engineering Theses & Dissertations

Diamond is the hardest bulk material with the highest thermal conductivity. It is also an excellent wide band gap material; hence, diamond is suitable for electronic, mechanical and biological applications. Unfortunately, natural diamond is prohibitively expensive for most technological applications. Polycrystalline diamond, with properties close to those of natural diamond, has been synthesized since the 1950s. Among many methods employed for diamond thin film synthesis, chemical vapor deposition (CVD) using microwave plasma (MW) is quite popular for several reasons. Well-confined plasma that does not touch the reaction chamber walls can be produced directly on the substrate. Hence, contamination in the …

Optimization Framework For A Radio Frequency Gun Based Injector, Alicia S. Hofler

Electrical & Computer Engineering Theses & Dissertations

Linear accelerator based light sources are used to produce coherent x-ray beams with unprecedented peak intensity. In these devices, the key parameters of the photon beam such as brilliance and coherence are directly dependent on the electron beam parameters. This leads to stringent beam quality requirements for the electron beam source. Radio frequency (RF) guns are used in such light sources since they accelerate electrons to relativistic energies over a very short distance, thus minimizing the beam quality degradation due to space charge effects within the particle bunch. Designing such sources including optimization of its beam parameters is a complex …

Creation Of Large Scale Face Dataset Using Single Training Image, Qun Wang

Electrical & Computer Engineering Theses & Dissertations

Face recognition (FR) has become one of the most successful applications of image analysis and understanding in computer vision. The learning-based model in FR is considered as one of the most favorable problem-solving methods to this issue, which leads to the requirement of large training data sets in order to achieve higher recognition accuracy. However, the availability of only a limited number of face images for training a FR system is always a common problem in practical applications. A new framework to create a face database from a single input image for training purposes is proposed in this dissertation research. …

A Vision-Based Automatic Safe Landing-Site Detection System, Yufei Shen

Electrical & Computer Engineering Theses & Dissertations

An automatic safe landing-site detection system is proposed for aircraft emergency landing, based on visible information acquired by aircraft-mounted cameras. Emergency landing is an unplanned event in response to emergency situations. If, as is unfortunately usually the case, there is no airstrip or airfield that can be reached by the un-powered aircraft, a crash landing or ditching has to be carried out. Identifying a safe landing-site is critical to the survival of passengers and crew. Conventionally, the pilot chooses the landing-site visually by looking at the terrain through the cockpit. The success of this vital decision greatly depends on the …