Electrical and Computer Engineering Commons^™

Zero-Broadening Measurement In Brillouin Based Slow-Light Delays, Andrzej Wiatrek, Ronny Henker, Stefan Preußler, Max Ammann, Andreas Schwarzbacher, Thomas Schneider

Articles

A novel method for the achievement of zero-broadening in a SBS based slow-light system is discussed in theory and demonstrated experimentally. The system is realized just with a single broadened Brillouin gain. It is shown, that if the gain bandwidth is much broader than the initial pulse width, the output pulse width decreases with increasing pump power. A compression of approximately 90 % of the initial pulse width was achieved in simulation and experiment.

Inverse Scattering Solutions With Applications To Electromagnetic Signal Processing, Jonathan Blackledge, Timo Hamalainen, Jyrki Joutsensalo

Articles

When a signal is recorded that has been physically generated by some scattering process (the interaction of electromagnetic, acoustic or elastic waves with inhomogeneous materials, for example), the ‘standard model’ for the signal (i.e. information content convolved with a characteristic Impulse Response Function) is usually based on a single scattering approximation. An additive noise term is introduced into the model to take into account a range of non-deterministic factors including multiple scattering that, along with electronic noise and other background noise sources, is assumed to be relatively weak. Thus, the standard model is based on a ‘weak field condition’ and …

Engineering Of A Single Alkaline Fuel Cell Part I: Construction Of A Test Bed, Jonathan Blackledge, James Brunton, Eugene Coyle, David Kennedy, Heinz Schmidt-Walter, Hans Kohnke, Gerhard Sauer, Steffen Schudt, James Hamilton

Articles

Fuel Cells offer a realistic, sustainable and clean alternative energy option for stationary and mobile applications. Hydrogen and fuel cell technologies are recognised by many as possible long term energy solutions, but to-date have failed to make an impact on the energy market. This is due to a number of key reasons, some of which include, efficiency, scale, accessories and power output. Applying fuel cells to small telecommunication components requires the applications of Micro and Nanotechnology, which have yet to be perfected to make them long lasting and cost effective. This paper outlines the reasons for commercialisation of fuel cells …

Engineering Of A Single Alkaline Fuel Cell Part Ii: Long Term Operation In Air, Jonathan Blackledge, Eugene Coyle, David Kennedy, Heinz Schmidt-Walter, Hans Kohnke, Steffen Schudt, Gerhard Sauer, James Hamilton

Articles

Research into renewable energy sources has previously lacked sufficient investment. However, emphasis has now shifted and funding is being made available in a proactive manner by various governments eager to encourage renewable energy technology and reduce carbon taxes. Fuel Cells offer a realistic, sustainable and clean alternative energy option for stationary and mobile applications. Hydrogen and fuel cell technologies are recognised by many as possible long term energy solutions, but to-date, have failed to make an impact on the energy market. This is due to a number of key reasons, some of which include efficiency, scale, accessories and power output. …

Hand-Held Flyback Driven Coaxial Dielectric Barrier Discharge: Development And Characterization, Victor J. Law, Vladimir Milosavljevic, Neil O’Connor, James F. Lalor, Steven Daniels

Articles

The development of a handheld single and triple chamber atmospheric pressure coaxial dielectric barrier discharge driven by Flyback circuitry for helium and argon discharges is described. The Flyback uses external metal-oxide-semiconductor field-effect transistor power switching technology and the transformer operates in the continuous current mode to convert a continuous dc power of 10–33 W to generate a 1.2–1.6 kV 3.5 μs pulse. An argon discharge breakdown voltage of ∼768 V is measured. With a 50 kHz, pulse repetition rate and an argon flow rate of 0.5–10 argon slm (slm denotes standard liters per minute), the electrical power density deposited in …

Real-Time Plasma Controlled Chemistry In A Two-Frequency, Confined Plasma Etcher, Vladimir Milosavljevic, Albert R. Ellingboe, Cezar Gaman, John V. Ringwood

Articles

The physics issues of developing model-based control of plasma etching are presented. A novel methodology for incorporating real-time model-based control of plasma processing systems is developed. The methodology is developed for control of two dependent variables (ion flux and chemical densities) by two independent controls (27 MHz power and O2flow). A phenomenological physics model of the nonlinear coupling between the independent controls and the dependent variables of the plasma is presented. By using a design of experiment, the functional dependencies of the response surface are determined. In conjunction with the physical model, the dependencies are used to deconvolve the sensor …

Influence Of Fiber Manufacturing Tolerances On The Spectral Response Of A Bend Loss Based All-Fiber Edge Filter, Pengfei Wang, Gerald Farrell, Yuliya Semenova, Ginu Rajan

Articles

It is shown that manufacturing tolerances of the fiber parameters bend radius and NA significantly influence the fiber bend loss performance and spectral response of a fiber-based edge filter. A theoretical model, validated by experimental results, is used to determine the changes in key spectral parameters for an edge filter, resulting from changes within their manufacturing tolerance range, for both the bend radius and NA. Finally is shown that bend-radius tuning during fabrication of such filters is a means of mitigating the effect of manufacturing variations.

Group Velocity Dispersion Reduction In Fibre-Based Slow-Light Systems Via Stimulated Brillouin Scattering, Ronny Henker, A. Wiatrek, K. U. Lauterbach, Max Ammann, Andreas Schwarzbacher, Thomas Schneider

Articles

Presented are theoretical investigations and simulations of a reduction of the group velocity dispersion (GVD) in slow-light systems by an optimisation of the gain spectrum of the stimulated Brillouin scattering (SBS). A comparison between a natural Brillouin gain spectrum and a broadened Brillouin gain spectrum with and without two additional losses at its wings is demonstrated. The focus of the theoretical examination was set on the superposition of a gain and two losses with an equal magnitude. Therefore, a low GVD and a high group index change could be achieved and hence, a small pulse distortion and a high time …

Reduction Of Ground-Plane-Dependent Effects On Microstrip-Fed Printed Rectangular Monopoles, Matthias John, Jonathan Evans, Max Ammann, J. C. Modro, Z. N. Chen

Articles

Methods to mitigate the strong dependence of impedance bandwidth on the ground- plane size for a rectangular printed planar monopole is described. It is shown that the bandwidth limitation may be overcome by introducing feed-line asymmetry, which alters the purity and the Q of the higher frequency modes and by ground-plane augmentation, which effects the lower frequency modes. A method of extending the ground plane without increasing the overall antenna size is shown to improve both the bandwidth and gain and also to enable the use of significantly smaller ground planes. The effects of these techniques on radiation pattern are …

Investigation On The Performance Of Upqc-Q For Voltage Sag Mitigation And Pq Improvement At A Critical Load Point, Malabika Basu, S. P. Das, Gopal Dubey

Articles

The unified power quality conditioner (UPQC) is one of the major custom power solutions, which is capable of mitigating the effect of supply voltage sag at the load end or at the point of common coupling (PCC) in a distributed network. It also prevents the propagation of the load current harmonics to the utility and improves the input power factor of the load. The control of series compensator (SERC) of the UPQC is such that it injects voltage in quadrature advance to the supply current. Thus, the SERC consumes no active power at steady state. The other advantage of the …

A Surface Inspection Machine Vision System That Includes Fractal Texture Analysis, Jonathan Blackledge, Dmitry Dubovitskiy

Articles

The detection, recognition and classification of features in a digital image is an important component of quality control systems in production and process engineering and industrial systems monitoring, in general. In this paper, a new pattern recognition system is presented that has been designed for the specific task of monitoring the quality of sheet-steel production in a rolling mill. The system is based on using both the Euclidean and Fractal geometric properties of an imaged object to develop training data that is used in conjunction with a supervised learning procedure based on the application of a fuzzy inference engine. Thus, …

Object Detection And Classification With Applications To Skin Cancer Screening, Jonathan Blackledge, Dmitryi Dubovitskiy

Articles

This paper discusses a new approach to the processes of object detection, recognition and classification in a digital image. The classification method is based on the application of a set of features which include fractal parameters such as the Lacunarity and Fractal Dimension. Thus, the approach used, incorporates the characterisation of an object in terms of its texture.

The principal issues associated with object recognition are presented which includes two novel fast segmentation algorithms for which C++ code is provided. The self-learning procedure for designing a decision making engine using fuzzy logic and membership function theory is also presented and …

V-Shaped Electro-Optic Response Observed In A Chiral Ferroelectric Smectic Liquid Crystal, V. Manjuladevi, Yuri Panarin, Jang-Kun Song, B. K. Sadashiva

Articles

We report on the observation of V-shaped switching in a ferroelectric liquid crystal cell over a wide range of temperatures. Results of the optical transmittance in the visible region give us the helical pitch for various temperatures of the ferroelectric liquid crystalline compound used. We show that the helical pitch, in addition to the spontaneous polarization (PS) and thickness of the alignment layer of the cell, is an important factor in giving V-shaped switching. A longer or helical compensated mixture gives a better V-shaped switching. © 2008 American Institute of Physics.

Extended Nonnegative Tensor Factorisation Models For Musical Sound Source Separation, Derry Fitzgerald, Matt Cranitch, Eugene Coyle

Articles

Recently, shift-invariant tensor factorisation algorithms have been proposed for the purposes of sound source separation of pitched musical instruments. However, in practice, existing algorithms require the use of log-frequency spectrograms to allow shift invariance in frequency which causes problems when attempting to resynthesise the separated sources. Further, it is difficult to impose harmonicity constraints on the recovered basis functions. This paper proposes a new additive synthesis-based approach which allows the use of linear-frequency spectrograms as well as imposing strict harmonic constraints, resulting in an improved model. Further, these additional constraints allow the addition of a source filter model to the …

Electro-Optic And Dielectric Study Of The De Vries-Type Smectic A* Phase Exhibiting Transitions To Smectic-C*A And Smectic-C* Phases, U. Manna, Jang-Kun Song, Yuri Panarin, Atsuo Fukuda, J. K. Vij

Articles

Mixtures of different compositions of an antiferroelectric liquid crystal compound that exhibits direct smectic-A*(Sm-A*)-smectic-C*A(Sm-C*A) transition with a ferroelectric liquid crystal compound that exhibits Sm-A*-smectic-C*(Sm-C*) transition are studied using electro-optics and dielectric spectroscopy. The results of optical texture, birefringence, and the tilt angle suggest that a part of the Sm-A* phase is of de Vries type, since an increase in the tilt angle with decreasing temperature results in a reduction in the value of the birefringence in the Sm-A* phase, whereas the birefringence at Sm-A* to Sm-C* transition goes up by 12.7%. The soft mode relaxation strength, the Landau coefficient of …

High Performance Zno Varistors Prepared From Nanocrystalline Precursors For Miniaturised Electronic Devices, Suresh Pillai, Declan Mccormack, John Kelly, Raghavendra Ramesh

Articles

An industrially viable solution-based processing route using minimal amounts of solvent has been used to prepare bulk quantity nanopowders (average particle size 15.3 nm) for the fabrication of ZnO varistors. The xerogels, calcined powders and sintered materials were fully characterised. The preparation of varistors from nanopowders has been optimised by studying the effect of temperature on grain growth, densification and breakdown voltage. The varistors are prepared by sintering at 1050 C for 2 hours, a temperature that is significantly lower than that used in the current industrial process. Highly dense varistor discs prepared from the sintered material produce devices, with …

Analysis Of Financial Data Using Non-Negative Matrix Factorization, Ruairí De Fréin, Konstantinos Drakakis, Scott Rickard, Andrzej Cichocki

Articles

We apply Non-negative Matrix Factorization (NMF) to the prob-lem of identifying underlying trends in stock market data. NMF is arecent and very successful tool for data analysis including image andaudio processing; we use it here to decompose a mixture a data, thedaily closing prices of the 30 stocks which make up the Dow Jones In-dustrial Average, into its constitute parts, the underlying trends which govern the financial marketplace. We demonstrate how to impose ap-propriate sparsity and smoothness constraints on the components of thedecomposition. Also, we describe how the method clusters stocks to-gether in performance-based groupings which can be used for …

Dual-Frequency Dual-Sense Circularly-Polarized Slot Antenna Fed By Microstrip Line, Xiulong Bao, Max Ammann

Articles

A new design of a dual-frequency dual circularly-polarized slot antenna is presented. The dual-frequency is achieved using a single-layer microstrip-fed configuration coupled to a modified annular-slot antenna. The dual sense circular-polarization is obtained by four unequal linear slots which augment the annular slot. Experimental results show the proposed antenna has good circular polarization characteristics for both right-hand circular polarization (RHCP) and left-hand circular polarization (LHCP). The 10 dB return loss impedance bandwidths for the lower (RHCP) and higher (LHCP) bands are 26.7% and 11.3%, respectively. The 3 dB axial-ratio bandwidths are 6.1% and 6.0% with respect to 1.5 GHz (RHCP) …

A Low Polarization Sensitivity All-Fiber Wavelength Measurement System, Ginu Rajan, Yuliya Semenova, Gerald Farrell, Qian Wang, Pengfei Wang

Articles

A low polarization-sensitive all-fiber wavelength measurement system using a twisted macro-bend fiber edge filter together with polarization-insensitive (PI) 3-dB coupler is presented. Eliminating the polarization-dependent loss (PDL) is essential when macro-bending single-mode fiber is utilized as an edge filter. A new bending configuration to eliminate the PDL of a fiber edge filter is proposed in this letter by twisting the fiber by 90deg between two bending sections with equal length. The PDL of this configuration retains a low value even while the bending length is increased to achieve a steeper response for the edge filter. This configuration together with a …

An All-Fiber Temperature Sensor Based On A Macro-Bend Singlemode Fiber Loop, Ginu Rajan, Yuliya Semenova, Gerald Farrell

Articles

An all-fibre temperature sensor is proposed based on a macro-bend singlemode fibre loop using a ratiometric power measurement scheme. The sensor has a linear characteristic with temperature at a fixed wavelength and bend radius. A direct linear relationship between the bend loss of the singlemode fibre and temperature is reported for the first time. By measuring the change in bend loss of the system a change in temperature can be measured assuming the system is calibrated. The proposed sensor has a higher temperature resolution than other conventional fibre-optic sensors and also benefits from simplicity.

Investigation On Singlemode-Multimode-Singlemode Fiber Structure, Qian Wang, Gerald Farrell, W. Yan

Articles

This paper presents an investigation on a single-mode-multimode-single-mode fiber structure. A one-way guided-mode propagation analysis for the circular symmetry waveguide is employed to model the light propagation and the approximated formulations are derived and evaluated concerning the accuracy. Phase conjunction of the multimode interference within the fiber structure is revealed. A simple way to predict and analyze the spectral response of the structure is presented through the space to wavelength mapping with the derived approximated formulations. The prediction of spectral response is verified numerically and experimentally.

Dual Frequency Dual Circularly-Polarised Patch Antenna With Wide Beamwidth, Xiulong Bao, Max Ammann

Articles

A dual-frequency dual-circularly polarised patch antenna with wide beamwidth is proposed. The two-layer structure comprises circular patches with offset circular slots connected to rectangular slots. They provide orthogonal perturbations realising RHCP and LHCP for the lower and upper bands, respectively. The wide beamwidth is realised by extending the substrate beyond the groundplane. Measurements show a maximum beamwidth of 180deg and gains of 3.9 and 0.5 dBic for zenith and 10deg elevation, respectively, for the upper band. The measured beamwidth for the low band is 130deg with a maximum gain of 3.9 and -0.7 dBic for zenith and 10deg elevation, respectively. …

Ratiometric Wavelength Monitor Based On Singlemode-Multimode-Singlemode Fiber Structure, Agus Hatta, Gerald Farrell, Qian Wang, Ginu Rajan, Pengfei Wang, Yuliya Semenova

Articles

An all-fiber ratiometric wavelength monitor for optical wavelength measurement is proposed and is investigated theoretically and experimentally. Two edge filters with opposite slope spectral responses based on singlemode-multimode-singlemode (SMS) fiber structures are developed. A ratiometric wavelength measurement system employing the developed SMS edge filters demonstrates a high discrimination range of 20.41 dB and a potential wavelength measurement resolution of 10 pm over a wavelength range from 1530 to 1560 nm.

Covert Encryption And Document Authentication Using Texture Coding, Jonathan Blackledge, Mary Hallot

Articles

With the improvements in the quality of Commercial-Off-The-Shelf (COTS) printing and scanning devices, the ability to counterfeit documents has become a widespread problem. Consequently, there has been an increasing demand to develop digital watermarking techniques which can be applied to both electronic and printed images (and documents) that can be authenticated, prevent unauthorized copying and withstand abuse and degradation. In this paper , a new approach to digital watermarking is presented and a range of possible applications are considered. The process is defined by using concepts and techniques borrowed from Cryptography. It is based on computing a 'scramble image' by …

Audio Data Verification And Authentication Using Frequency Modulation Based Watermarking, Jonathan Blackledge, Omar Farooq

Articles

An approach to watermarking digital signals using frequency modulation - ‘Chirp Coding’ - is considered. The principles underlying this approach are based on the use of a matched filter to reconstruct a ‘chirp stream’ code that is uniquely robust. The method is generic in the sense that it can, in principle, be used for a variety of different signal (the authentication of speech and biomedical signals, for example). Further, by generating a bit stream that is signal dependent, chirp coding provides a method of self-authentication, which has a wide range of applications including copyright protection and digital rights management. However, …

Experimental Study Of High-Temperature Smectic-C*F12 Phase In Chiral Smectic Liquid Crystals That Exhibit Phase-Sequence Reversal, K. L. Sandhya, J. K. Song, Yuri Panarin, J. K. Vij, S. Kumar

Articles

We report the results of an experimental study of a recently observed phase sequence reversal of smectic-C*FI2 [SmC*(qT=1/2); a four layer antiferroelectric] phase appearing in the temperature range above the smectic-C* (SmC*) phase from the results of optical birefringence, spontaneous polarization, selective reflection, conoscopy, and dielectric spectroscopy. The SmC*FI2 phase is observed in an antiferroelectric liquid crystalline compound, 10OHF, in a temperature range above that of SmC*A phase and is found to be thermodynamically monotropic, i.e., it appears only upon cooling from SmC*A phase. This is also unstable as if it is once transformed to SmC* by the application of …

Practical Sensor For Measurement Of Nitrogen, Dusan Popovic, Vladimir Milosavljevic, Steven Daniels

Articles

This paper presents a method for precise measurement of atomic and molecular nitrogen in an oxygen-nitrogen dc plasma. This is achieved by monitoring the intensities of the atomic nitrogen spectral line at 821.6 nm and the molecular nitrogen bandhead at 337.1 nm, relative to the atomic oxygen spectral line at 844.7 nm. Oxygen is one of the most frequently used gases for surface chemical treatment, including deposition and etching, therefore the ability to measure and control the process and chemical composition of the process is essential. To validate this oxygen actimometry method for N2-xO2 (where x varies from 0 to …

Wideband Printed Monopole Design Using A Genetic Algorithm, Matthias John, Max Ammann

Articles

A method for the design and optimisation of wide-band printed planar monopoles using a genetic algorithm is presented. This novel technique employs overlapping sub-patches which ensures electrical contact in such constellations where two sub-patches are touching only at the corner, hence re-ducing losses. The method was usd optimisation of wide-band printed planar monopoles using a genetic algorithm is presented. This novel technique employs overlapping sub-patches which ensures electrical contact in such constellations where two sub-patches are touching only at the corner, hence re-ducing losses. The method was used to design a wideband monopole antenna with application in higher cellular, WLAN …

Resolution Investigation Of A Ratiometric Wavelength Measurement System, Qian Wang, Ginu Rajan, Pengfei Wang, Gerald Farrell

Articles

Theoretical analysis and experimental investigations are presented on the resolution of a ratiometric wavelength measurement system. Theoretical modeling indicates that the resolution of a ratiometric wavelength measurement system is determined by the signal-to-noise ratio of the input signal and the noise of the photodetectors associated with optical-to-electronic conversion. For experimental verification, a ratiometric system employing a macrobending standard single-mode fiber is developed and corresponding results are in good agreement with the theoretical prediction.

Polarization Dependence Of Bend Loss For A Standard Singlemode Fiber, Qian Wang, Ginu Rajan, Pengfei Wang, Gerald Farrell

Articles

Polarization dependence of bend loss caused by the polymer coating layer for a standard singlemode fiber (SMF28) is investigated theoretically and experimentally. Bend loss for SMF28 for both the TE and TM mode is calculated separately. Normalized polarization dependent loss is proposed for the characterization of the polarization sensitivity of bend loss for different bend radii. Corresponding experimental tests are presented, which agree with the theoretical results. Both the theoretical and experimental results show that the polymer coating layer has a significant influence on the polarization dependence of bend loss.