Electrical and Computer Engineering Commons^™

Logic Simulation And Methodologies For Design For Testability, Ravi Shankar Prasad Mallampalli

Theses

This thesis describes the method used for developing the standard TTL blocks using the logic simulator SPLICE1. It also gives a comprehensive overview of methods which can be used for designing a circuit which is testable. A format called Electronic Design Interchange Format (EDIF) is also described as a tool which can be used for transporting design data in the VLSI indgstry.

Multi-H Continuous Phase Modulation : Its Properties And Analysis, Jyung-Cheng Chen

Theses

Multi-h CPM, a generalization of CPFSK and also one of the so-called Combined Modulation and Coding schemes, is useful in digital communication systems where both the bandwidth and power are constrained. The increased signal processing complexity, which can be viewed as the third communication resource, is used to trade for both power and bandwidth, and to approach the error-free communication promised by Shannon's theorem.

The transmitted multi-h CPM signal carries a coded sequence of continuous phase changes; the possible phase states form a cylindrical trellis in phase and time, in which the modulation indices are reused in a cyclical fashion. …

Reliability Of Dielectrics : Using Noise As A Diagnostic Tool, Ramesh K. Jain

Theses

The aim of this thesis is to develop a screening method to predict the reliability of a dielectric material. The screen chosen is an electrical noise. The dielectric material studied is varnished fibre glass cloth material supplied by Westinghouse Electric Corporation.

The dielectric material will have varying amount of voids, crystal defects, and surface contaminants impurities introduced during manufacturing process. On application of the electric stress, ionization (corona) will take place. The corona degrades the material due to thermally generated heat, chemical reactions in the voids and ionic bombardment of the material.

An experimental set up is developed to monitor …

Gallium Film Formation By Ion Cluster Beam Deposition, Te-Chuan Hsu

Theses

Gallium thin films were deposited by Ion Cluster Beam (ICB) from pure gallium. This research had two objectives: to develop a practical method of crucible heating to generate gallium clusters; and to investigate the influence of ICB system parameters on the formation of clusters and film properties. An electron-bombardment crucible heater with a novel construction was designed. The top section of the carbon crucible was kept at a higher temperature than the middle section to prevent clogging of the nozzle and " spitting " phenomena which were found to occur with the conventional design. Crucible temperatures up to about 1360°C …

The Modeling Of A Self-Oscillating Dc-To-Dc Converter, Frank Andrew Linkowsky

Theses

This thesis develops a model of a nonlinear self oscillating current-or-voltage step-up dc-to-dc converter. Expressions are given that predict the operation of the converter in the time domain and in the state plane. To verify these expressions, a large signal computer simulation technique [1] is used to compare theoretical results with actual measurements. This type of simulation allows a nonlinear switching converter to be modeled with a series of piecewise-linear operating intervals. The resulting waveforms predicted by the developed model show close agreement with waveforms found in the laboratory. Therefore, the model represents a powerful tool that may be used …

Design And Optimization Of Nmos Sense Amplifiers For Vlsi Drams, Nimish K. Shah

Theses

The aim of this thesis is to study and optimize the performance of NMOS sense amplifiers used in modern VLSI DRAMs.

Initially dynamic memory cells and popular sense amplifier circuits are surveyed.

A standard five transistor sense amplifier is later chosen for detailed analysis. Layout of the circuit is drawn to get the physical parameters. Using SPICE simulator, various effects of circuit parameters are studied. From these results optimal values of these parameters are arrived at.

Also an effort is made to derive theoretically equations for the latching time of a post amplifier which is the most important part in …

Reliability Studies On Solid Tantalum Electrolytic Capacitors By Means Of Accelerated Life Tests, Venkata R. Golthi

Theses

The purpose of this thesis is to understand the failure mechanisms in Solid Tantalum Capacitors encapsulated in plastic, and to suggest the precautionary measures that prevent the occurrence of these failures.

The reliability of Solid Tantalum Capacitors encapsulated in plastic is of considerable interest because in some applications where the mechanical accelerations or shocks are considerable the "better" "hermitically" sealed type are not able to sustain themselves. Poor adherence between the dielectric film and the base metal Tantalum under the conditions of sudden mechanical shocks, causes problems.

Our study was carried out in two different directions, theoretical and experimental. The …

Linearization Accuracy In Probabilistic Load Flow, Guan-Zhong Liang

Theses

This paper presents a linear load flow method which can be used for probabilistic load flow analysis. The method is based on least-square estimation. To estimate its accuracy in linear load flow calculations, the method and a previously developed linear load flow method are applied to a typical power system and the results evaluated. Comparable accuracy is noted.

On-Line Analysis Of Highly Coherent Brain Activity During Transcendental Meditation And Automated Biofeedback, Deepak Dinkerrai Rawal

Theses

Occurance of highly coherent brain activity (EEG) specific to the meditation has been reported in the literature. The present thesis is an effort to look into the mechanics of meditation using the recent technique of analysis of high coherence in the EEG. Based on previous work, reporting increased EEG coherence during practice of Transcendental Meditation, a closed loop model and hypothesis is proposed using biofeedback to close the loop. The hypothesis proposes that very high coherence in the EEG is a very significant neurophysiological parameter, reflecting instantaneous quality of meditation in the form of an average high coherence above threshold. …

Replacement Of Surface Ducted Rays Near Caustics With Guassian Beams, Carlos Javier Ruiz

Theses

Conventional approach to a solution of a wave propagation problem in an inhomogeneous medium is to utilize either rays or modes to represent the wave field. Asymptotic ray theory (ART) starts to fail in the vicinity of caustics due to rays experiencing many reflections. Even uniform representations do not properly correct this deficiency of rays when caustics start to pile up in the far range. One possible alternative is to replace these rays with modal bundles and remainders [1]. A promising technique using Gaussian Beams has been used to represent the total field due to a point or a line …

Ray And Beam Representation Of The Glancing Phenomena, Michael Sotiriou Vogas

Theses

Asymptotic ray theory (ART) is a widely used method dealing with problems of wave propagation in an inhomogeneous medium. The main deficiency of ART is in transition regions where rays near caustics, glancing and critical incidence fail to represent the actual wave field. Ray bundles in such transition regions have been successfully replaced with modal bundles and remainders El] in well defined profiles. However , in practical problems it is difficult to implement modal representations and almost impossible to express remainders. Recently emerging Gaussian beam method (GBM) has shown promising results in representing the total field produced by a source …

Multi-Channel Arrhythmia Analysis In The Clinical Exercise Electrocardiogram, Shi-Xiong Yang

Theses

This thesis studied methods of using 2 channel ECG signals for noise elimination and arrhythmia detection. Clinical data were recorded from patients stress tests and were stored on diskettes for off-line processing. Spatial velocity vector and noise estimation methods in addition to analog and digital filters were combined to remove the noise produced from different sources. Feature extraction and matched filter methods were employed for classification of normal and abnormal QRS complexs, while rhythm computing was used in addition for PVCs and other arrhythmia discrimination. This algorithm was tested on clinical stress test recordings and a computer simulated arrhythmia recording …

Microcomputer Local Area Network Interface, David W. Juan

Theses

A Microcomputer Local Area Network Interface system for use in the study of Local Area Network has been built and tested. The special feature of the system is data transmission/receiving and error detection/recovery. The system adapted the International Standards Organization (ISO) Open System Interconnection COSI) model. It used the star topology and implemented the physical layer, data link layer and network layer. The results of the system indicated the data communications and resources—sharing between microcomputers.

Design And Evaluation Of Performance For The Multi-Microprocessor System, Sang-Soo Lee

Theses

A tightly coupled multiple-microprocessor with two MPU's that can be run at different clock speeds has been built and tested. The method of interconnection for this multiprocessor is a timeshared common bus with shared memories having a tightly coupled architecture. The signal timipg of the multiprocessor system for different speeds has been investigated using a logic analyzer for simulation modeling. The desired timing results have been obtained. According to the timing results, the simulation model for the General Purpose Simulation System has been correctly designed and performance of the multiprocessor system for the various clock speeds has been evaluated by …

An 8052 Ah - Basic, Based Development System, Suresh Vishwanath Leley

Theses

This project exploits the latest in microcontrollers-an entire environment for developing and prototyping a microcontroller application. With one key chip, a little glue, and a Dumb terminal a powerful system is achieved at a vanishingly small cost. This "one chip" system is adequate for realizing a wide range of applications calling for a small computer or an embedded processor.

Besides economy of system cost, the turn around time from concept to functioning application can be extremely short, even when the development engineer is not particularly well acquainted with traditional assembly language and microprocessor development practices. This economy is achieved by …

An Analysis Of Minimum Shift Keying From The Viewpoints Of Quadrature Multiplexed And Multi-H Continuous Phase Modulation Signaling, Alfred Anthony De Seta

Theses

Minimum Shift Keying (MSK) is a bandwidth efficient modulation scheme which offers superior performance over Quadrature Phase Shift Keying (QPSK) and Offset Quadrature Phase Shift Keying (OQPSK). This paper discusses these modulation techniques from a quadrature multiplexed signaling viewpoint and compares them in terms of error performance, bandwidth properties and bandlimiting and hardlimiting effects. MSK is also considered as a special case of a multi-h Continuous Phase Modulation (CPM) signal and the Viterbi algorithm is presented as an optimal detection scheme for this class of signals. A computer simulation is performed with the VA as the detection mechanism for an …

A Computer Aided Manufacturing System For Small Quantity Prototype Board Production, Santiago Garcia-Perez

Theses

A matrix addressed manufacturing tool has been built, tested, and integrated in a system aimed to exploit wire-wrap wiring technology for protoboard production in small quantities. Extensive software exploits the power and economy of the personal computer as a superb manufacturing tool and documentation system. Computer graphics are used as a visual aid that takes advantage of the cognitive capabilities of the human mind and eliminates the boredom and high costs involved with heavy automation achieving instead a tolerable level of human engagement with significantly increased efficiency. The approach presented is new and delivers substantial gains in productivity. The software …

Measurements Of Basic Semiconductor Properties, Abdolreza Ariantaj

Theses

Mobility, resistivity, and total impurity concentration of several purchased p-type silicon samples with known resistivities were measured by Hall effect, experiments utilizing the Van Der Pauw method. The silicon samples will serve as Hall effect standards for future measurements on other semiconductor materials, particularly gallium nitride ion cluster beam (ICB) deposited thin films. The samples which were Freshly etched with hydrofluoric acid had measurement values of 455 cm ² / V.sec, 45.9 Ω cm, and 2.6 X 10¹⁴ cm³ for mobility, resistivity, and total impurity concentration, respectively. The mobility values were within 9.9 per cent, of the published values …

The Acquisition Of Direct Sequence Spread Spectrum Communication Systems, Anthony Donald Demeri

Theses

This Paper surveys different techniques of acquiring Direct Sequence Spread Spectrum Systems.

It classifies different systems, indicates the strongpoints and weakness of each, along with some applications.

One method, The Single Dwell Serial PN Acquisition System is then focused on in detail. The detail includes analysis of standard version, derivation of the mean time to acquire, the variance, the probability of detection and the probability of a false alarm.

In the last section of the paper the analytical results of the Single Dwell Serial PN Acquisition System shall be confirmed by computer simulation.

Effect Of Humidity And Moderate Temperature On Microcircuit Failure, Antoine Mikhayel Chaia

Theses

The increased use of microprocessors has brought forth many questions concerning the reliability of these devices.

This research discuss the TTL integrated circuit failure rates, and provides information on the effects of temperature, device complexity and packaging on TTL failure rates under storage condition of 100% R.H. (Relative Humidity) and 100°C and no added humidity at 100°C. Other factors which can affect failure rate are also discussed, including designs, materials process.

Approximately 200 microcircuits of TTL (74LS00) were subjected to extend life testing at 100°C; where 125 chips are tested at 100°C ± 2° and no added humidity and the …

Nervous System Simulation, Jian Chen

Theses

This thesis deals with the nervous system simulation. The Hodgkin-Huxley model and Stein's model are used as basic tools. The author has tried to describe some practical problems by mathematical models.

First, the horse-shoe crab eye is investigated. Light intensity is reported to the brain by the firing frequency of the photoreceptoe. A Poisson process is used to simulate the stimulus to the receptor. The result of the stochastic model coincides with the theoretical one: receptor overlapping decreases the resolving power of the eye; and the lateral inhibition compensates the effect of overlapping.

Second, a nerve muscle model was set …

Realization And Implementation Of A Recursive Digital Convolution Algorithm In Cmos, Lik Tang Cheng

Theses

This thesis describes the implementation of a digital convolver. A recursive digital convolution algorithm was realised and implemented by using CMOS circuitry. This thesis also gives a technical overview of current CMOS processing technologies as well as various novel CMOS logic circuit techniques.

Waveform Analysis Using A Micro Computer, Dakshina K. Murthy

Theses

Harmonic analysis through a micro computer was performed at Brookhaven National laboratory to determine the magnitude and extent of hormonic dIstortionon in their electrical power supply system. DT 2801 Hardware and MADCAP software were used to accomplish the Harmonic anylysis through forier transform.

The Dielectric Slab-Wedge Antenna, B. Keith Christensen

Theses

A theoretical model and numerical investigation of the directive gain of a dielectric slab-wedge radiator is presented. The model is based on a union of the classical dielectric slab equations, local mode theory, and equivalent current distribution treatments of the truncated dielectric slab and wedge geometries.

The far field is developed from the sum of two current distributions. The slab region, up to the transition plane between slab and wedge, is replaced by equivalent electric and magnetic surface current densities. The wedge contribution is developed from a volume polarization current distribution.

Conservation of power is used to approximate the field …

Computer-Aided Design Of A Waveguide To A Suspended Stripline Transition For Millimeter-Wave Applications, Hsin-Yen Peng

Theses

Realization of millimeter-wave systems on suspended striplines necessitates transitions from such lines into waveguides for measurements and other purposes. Transition can be obtained through coupling TE10 mode in the waveguide into a TEM mode in the suspended stripline. A continuous transition using tapered complementary unilateral finline and two gradually increasing conducting tapered ridges is studied here. The tapered region is modelled using a number of uniform sections with gradually changing cross sections. The junction separating the tapered section from the suspended stripline is modelled via physically and electrically continuous terminations. Physical continuity approach is more flexible for manufacturing purpose at …

Reliability Study Of Liquid Crystal Display, Kalpesh Mahendra Desai

Theses

The purpose of this thesis is to study the reliability of liquid crystal display under different temperature conditions. To accomplish this, accelerated life testing was done on the soft glass and the hard glass liquid crystal display units at 77 C and 85 C temperature without any added humidity or voltage.

As the current is a usefu1 indicator for probable wear of liquid crystal display, leakage current was measured at 0 hour, 1000 hours, 2000 hours and 3000 hours when the units have stabilized at room temperature.

The date shows higher spread for the hard glass units. This may indicate …

The Interfacing Between The A/D Converter, Buffer Memory And Hx-40 Microcomputer, Yu-Hwa Chu

Theses

The data acquisition system which includes A/D converter, buffer memory, and address generator, is to digitize the signal for the computer use. The special feature of this system is the computer controlled digitizing rate over a range from 35K to 0.

The interfacing between Motorola 68000 E.C.B. to H.P. 64000 Development System is the simple example for data communication. How to make the protocal to be compatible is the main point. H.P. 64000 is treated as a host computer because it has the capability for data management and large memory for storing data.

Digital Signal Processing On Tms32010 Evaluation Module And Analog Interface Board, Jiming Sun

Theses

The TMS32010 Evaluation Module (EVM) and Analog Interface Board (AIB) have been used to implement a digital signal processing system. This new system will be the hardware basis for research and development in the DSP field at NJIT in the future. This thesis will serve as a user's guide and overall technical manual for the system.

TMS32010 Assembler, Linker and Simulator in VAX-11 are used to develop the system software, then we can down load the object codes to the EVM through the MODEM in order to test them. By using the A/D and D/A converter as input and output …

Optimization Of Reactive Ionized Cluster Beam (R-Icb) Technique For Deposition Of Gan Films, Veronica S. Kyriacou

Theses

The deposition of GaN film onto glass substrate, using the Reactive - Ionized Cluster Beam deposition technique was studied. The creation of clusters is dictated by various parameters such as the vacuum pressure inside and outside the crucible, the crucible temperature, and the nozzle diameter of the crucible. Optimization of these parameters was experimentally studied, and deposition of gallium films on glass substrates was tried as a first step.

The direct heating method was used at first to get the 1100¬1300°C crucible temperature which was required for the creation of gallium clusters. Although different tungsten wire diameters and different number …

The Gpib User's Manual For Hx-40, Ding-Tang Li

Theses

A completed RS-232 to GPIB interfacing system has been built for HX-40 to master the GPIB oriented machine through its serial port. GPIB commands and data can be transfered between HX-40 and the slave station, which is a HP 3582A spectrum analyzer in this project. The data acquisition from serial to GPIB is done by a well-made GPNET mode 10 interfacing board in a transmitting rate of 9600 baud rate. GPNET exchanges data and commands with HX-40 through a RS-232 port, and passes them to the slave station through a GPIB port which is coordinated by GPIB protocol. A software …