Electrical and Computer Engineering Commons^™

Control Of Power Electronic Interfaces In Distributed Generation., Mohammad Mohebbi

Electronic Theses and Dissertations

Renewable energy has gained popularity as an alternative resource for electric power generation. As such, Distributed Generation (DG) is expected to open new horizons to electric power generation. Most renewable energy sources cannot be connected to the load directly. Integration of the renewable energy sources with the load has brought new challenges in terms of the system’s stability, voltage regulation and power quality issues. For example, the output power, voltage and frequency of an example wind turbine depend on the wind speed, which fluctuate over time and cannot be forecasted accurately. At the same time, the nonlinearity of residential electrical …

Ground Station Tracking System, Garret Hilton, Carter Mciver, Steven Hamby, Trevor Gahl, Casey Coffman, David Schwehr

2017 Academic High Altitude Conference

One of the Eclipse Ballooning Project’s main goals was to stream live video of the eclipse to the internet. To accomplish this task a tracking antenna was built to follow the balloon payload. As an added challenge, the task had to be completed on a budget. The “ground station” is the center for communication between the payload and user. This system utilizes GPS position reports from the payload via the iridium network to determine the balloons position. The computer algorithm takes in additional GPS and IMU data from the ground station to determine a relative heading to orientate the antenna …

Co-Existence Of Microbial Ecology In A Chemostat Using A Robust Feedback, Hector Puebla, Mariana Rodriguez-Jara, Margarita M. Gonzalez-Brambila, Eliseo Hernandez-Martinez, Alejandra Velasco-Perez, Ennio Piceno-Diaz

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

Food Web Control And Synchronization Using A Robust Feedback, Hector Puebla, Mariana Rodriguez-Jara, Cesar S. Lopez-Monsalvo, Eliseo Hernandez-Martinez, Alejandra Velasco-Perez

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

Quantitative Analysis Of Regenerative Energy In Electric Rail Traction Systems, Mahmoud Saleh, Oindrilla Dutta, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper aims at determining the influential factors affecting regenerative braking energy in DC rail transit systems. This has been achieved by quantitatively evaluating the dependence of regenerative energy on various parameters, such as vehicle dynamics, train scheduling, ground inclination and efficiency of the electrical devices. The recuperated power and energy have been presented by a mathematical model, comprising of a set of empirical forms, which allows for thorough analysis. A detailed simulation model of a typical DC-traction system has been developed to validate the developed empirical forms. The results verified the validity of the proposed mathematical model, and demonstrated …

Optimal Microgrids Placement In Electric Distribution Systems Using Complex Network Framework, Mahmoud Saleh, Yusef Esa, Nwabueze Onuorah, Ahmed Mohamed

Publications and Research

This paper provides a new approach to find the optimal location for Microgrids (MGs) in electric distribution systems using complex network analysis. An optimal location in this paper refers to a location that would result in increased grid resilience, reduced power losses, less line loading, higher voltage stability and secured supply to critical loads during power outage. The criteria used to find the optimal placement of MGs were based on the centrality analysis adopted from complex network theory, the center of mass concept used in physics, and the controlled delivery grid (CDG) concept. An IEEE 30-bus system was used as …

Event And Time-Triggered Control Module Layers For Individual Robot Control Architectures Of Unmanned Agricultural Ground Vehicles, Tyler Troyer

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Automation in the agriculture sector has increased to an extent where the accompanying methods for unmanned field management are becoming more economically viable. This manifests in the industry’s recent presentation of conceptual cab-less machines that perform all field operations under the high-level task control of a single remote operator. A dramatic change in the overall workflow for field tasks that historically assumed the presence of a human in the immediate vicinity of the work is predicted. This shift in the entire approach to farm machinery work provides producers increased control and productivity over high-level tasks and less distraction from operating …

Energy Management Algorithm For Resilient Controlled Delivery Grids, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed, Haim Grebel, Roberto Rojas-Cessa

Publications and Research

Resilience of the power grid is most challenged at power blackouts since the issues that led to it may not be fully resolved by the time the power is back. In this paper, a Real-Time Energy Management Algorithm (RTEMA) has been developed to increase the resilience of power systems based on the controlled delivery grid (CDG) concept. In a CDG, loads communicate with a central controller, periodically sending requests for power. The central controller runs an algorithm, based on which it may decide whether to grant the requested energy fully or partially. Therefore, the CDG limits loads discretionary access to …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

Pursuit Evasion With Multiple Pursuers : Capturing A Ground Vehicle On A Road Network With Multiple Drones, Blake Wilson, Shreyas Sundaram, Amritha Prasad

The Summer Undergraduate Research Fellowship (SURF) Symposium

Unmanned Aerial Vehicles (UAV) have many military and civilian applications, one of which is monitoring a given area (such as a road network) for threats. An important question in this application is to determine the latest time to dispatch UAVs for the guaranteed capture of threats attempting to travel through the network. In this work, we consider a pursuit evasion scenario with multiple pursuers (UAVs) trying to catch a single evader (ground vehicle), where information about the evader’s path is provided by ground sensors. In this scenario, we consider the problem of finding the maximum delay with which the pursuers …

Observation And Estimation Study For Sensorless Control Of Linear Vapor Compressors., Joseph Latham

Electronic Theses and Dissertations

Linear vapor compressors have become widely investigated for refrigeration applications due to their high efficiency in comparison to the more common rotary type compressors. However, the nature of the linear compressor adds complexity to the control of these machines. The unconstrained motion of the piston in a linear compressor allows for continuous modulation of the compressor output, but requires knowledge of the mechanical dynamics to effectively control the compressor and prevent collision of the piston with the cylinder head. This control is made more difficult by the highly nonlinear nature of the force of gas compression acting against the piston. …

Two Senior Projects: 2.4 Ghz, 40% Efficiency Radio Frequency Amplifier, Ieee Design Contest, & Design And Implementation Of A Software Costas Loop For Audio Frequencies, Robert J. Tong

Electrical Engineering

How to Read this Document:

This document combines two senior project reports. The first senior project documents designing a class AB RF amplifier. The second, discusses the design and implementation of a software Costas loop for audio frequencies. The first report begins on the next page, while the Costas loop report starts on page 24. The two reports are orthogonal from one another. It is not a prerequisite to read the RF amplifier report before reading the Costas loop report. This document is merely two reports combined into one document. The second report, about the Costas loop, was written as …

Statistical Movement Classification Based On Hilbert-Huang Transform, Shanqi Sun

Graduate Theses and Dissertations

The goal of this project is to introduce an automatic movement classification technique of

finger movement signals using Hilbert-Huang Transform (HHT). Due to the nonlinear and

nonstationary processing behavior, movement signals are analyzed with the Hilbert-Huang

Transform (HHT). The slope of auto-correlation function and mean of frequency from first

three Intrinsic Mode Functions (IMFs) was used as feature parameters for each category.

Finally, performing support vector machine (SVM) for pattern classification completes clas-

sifying types of finger movement. According to the records of 669 trial samples of two types

of finger movement signals (thumb and pinky), average accuracy is 93.28%. …

Ros Based High Performance Control Architecture For An Aerial Robotic Testbed, Christoph Hintz

Electrical and Computer Engineering ETDs

The purpose of this thesis is to show the development of an aerial testbed based on the Robot Operating System (ROS). Such a testbed provides flexibility to control heterogenous vehicles, since the robots are able to simply communication with each other on the High Level (HL) control side. ROS runs on an embedded computer on-board each quadrotor. This eliminates the need of a Ground Base Station, since the complete HL control runs on-board the Unmanned Aerial Vehicle (UAV).

The architecture of the system is explained throughout the thesis with detailed explanations of the specific hardware and software used for the …

Autonomous Speed Control For Kia Optima, Andrew J. Combs, Kyle Fugatt, Kevin Mcfall

The Kennesaw Journal of Undergraduate Research

The standard method for speed control is the cruise control system built into most modern vehicles. These systems employ a PID controller which actuates the accelerator thus, in turn, maintains the desired vehicle speed. The main drawback of such a system is that typically the cruise control will only engage above 25 mph. The goal of this paper is to describe a system which we used to control vehicle speed from a stop to any desired speed using an Arduino microcontroller and a CAN BUS shield, from where autonomous features can be built upon. With this system, we were able …

Acceleration Amplitude Control System For Oscillating Silicon Oil Physics Experiment, Eric Chen

Electrical Engineering

This project is an ‘acceleration amplitude control system’ for use in an ‘oscillating silicon oil physics experiment’. The physics experiment has a tray of silicon oil. This tray must oscillate vertically at a specific amplitude (either at or just below the level for Faraday Waves). This control systems manages taking measurements of acceleration amplitude, and also manages correcting the shaker’s driving signal to obtain the correct acceleration. Features of the control system are designed for ease of use, because the system will mostly be operated by professor/ students without background knowledge in electrical engineering.

Dc House Energy Management System, Zachary L. Eldredge, Zoe M. Hay

Electrical Engineering

In this work, a previously completed proof of concept for an Energy Management System (EMS) for the DC House project has been revised and re-implemented. The implemented design changes will improve the performance and reproducibility of the system. This new design of the EMS replaces the two-separate buck and boost DC-DC converters with a single bidirectional DC-DC converter to reduce components and improve efficiency. Analysis of the bidirectional DC-DC converter shows high efficiency especially at larger load currents. The code of the previous work was updated for smoother operation as well as to accommodate an LCD capable of displaying more …

Dc-Dc Converter Control System For The Energy Harvesting From Exercise Machines System, Alexander Sireci

Master's Theses

Current exercise machines create resistance to motion and dissipate energy as heat. Some companies create ways to harness this energy, but not cost-effectively. The Energy Harvesting from Exercise Machines (EHFEM) project reduces the cost of harnessing the renewable energy. The system architecture includes the elliptical exercise machines outputting power to DC-DC converters, which then connects to the microinverters. All microinverter outputs tie together and then connect to the grid. The control system, placed around the DC-DC converters, quickly detects changes in current, and limits the current to prevent the DC-DC converters and microinverters from entering failure states.

An artificial neural …

Light Sensing Automated Blinds, Andrew B. Hodges, Ryan C. Flick

Electrical Engineering

This project is solving the problem of wasted energy within buildings and homes, because currently the lights turned on inside building do not utilize natural, ambient light from the sun. Rather than having unnecessary light from a light source, the automated light sensing smart blinds can sense the amount of light outside the window and in the room, and then adjust the angle of the blinds to save energy by utilizing the available outdoor light. This way, the light source will not be running at maximum power output while there is excess light coming through the window. This project aims …

Mini High Temperature Test Unit Final Design Report, Kevin Liu, Juan P. Castillo

Mechanical Engineering

Lawrence Livermore National Laboratory has invested considerable effort to develop new standard for nuclear grade HEPA filters that can withstand high temperatures along with methods to optimally test not only the experimental filter media, but also new frame seals and media binders. Therefore, LLNL in collaboration with Cal Poly has designed and built a Mini High Temperature Testing Unit (MHTTU) to recreate conditions observed during a fire and to test different materials in an effective, inexpensive, regulated and reliable method. The existing prototype was unable to achieve the ideal testing conditions of 1000°F air at the low flow rates of …

Modeling And Charging Control Of A Lithium Ion Battery System For Solar Panels, Garrett David Heinen

Master's Theses

The advancement in solar panel and battery technology makes them useful for energy supply and storage. This thesis involves the modeling and charging control of a lithium ion battery system for solar panels. The proposed model is based on the parameters and characteristics of a realistic battery and solar panel system; and the hybrid control approach combines the advantages of the adaptive incremental conductance method and the perturb and observe method to track the maximum power point of the solar panel for charging the battery unit. Computer simulation results demonstrate that this proposed approach offers a faster convergence rate than …

An Exact Analysis For Four-Order Acousto-Optic Bragg Diffraction Which Incorporates Both Incident Light Angle And Sound Frequency Dependencies, Adeyinka Sunday Ademola

Electrical Engineering Theses

This thesis extends the prior work which produced an exact solution to the four-order acousto-optic (AO) Bragg cell with assumed fixed center frequency and with exact Bragg angle incident light. The extension predicts the model that incorporates the dependencies of both the input angle of light and the sound frequency. Specifically, a generalized 4^th order linear differential equation (DE), is developed from a simultaneous analysis of four coupled AO system of DEs. Through standard methods, the characteristic roots, which requires solving a quartic equation, is produced. Subsequently, a derived system of homogeneous solutions, which absorbs the roots obtained using …

Automation In Entertainment: Concept, Design, And Application, Ryan Thally

Undergraduate Honors Theses

The focus of this thesis is to explore the automation technology used in the modern entertainment industry. Upon completion of my thesis, I will deliver a working prototype of the chosen technology and present its capabilities in a choreographed show.

A Novel Time-Domain Method Of Fault Diagnosis In Induction Motors, Bryan J. Davis

Honors Scholar Theses

This paper introduces a novel time-domain method for detecting the four major types of induction motor faults without requiring complex signal processing or additional sensors other than those already in place for closed-loop motor control. This method artificially modulates the motor current feedback signal with a perturbed frequency that oscillates about the characteristic frequency of the fault in question. After filtering out the unwanted frequency components that result from the modulation, the selected fault-indicative component is a very slow sinusoid that is only present when the fault is present. The method looks for this fault-indicative component by monitoring the time …

Hardware Realization Of A Residential Static Var Compensator, Muhammad Kamran Latif

Boise State University Theses and Dissertations

Conservation by Voltage Reduction (CVR) is the implementation of a distribution voltage strategy whereby all distribution voltages are lowered to the minimum allowed by the equipment manufacturer. This strategy is rooted in the fact that many loads consume less power when they are fed with a voltage lower than nominal. Electric utility companies consider CVR as a potential solution for managing power in distribution networks. However, a difficult challenge is to keep end-of-line (EOL) voltages within an acceptable range of the ANSI Standard C84.1. Therefore, to achieve maximum benefit from CVR, electric utilities should be able to regulate residential voltages …

Hybrid-Impulsive Higher Order Sliding Mode Control In Reduced Information Environment, Fathi M. Aldukali

Research Horizons Day Posters

No abstract provided.

Centralized Control For Dc Microgrid Using Finite State Machine, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

In this paper, an autonomous communication-based centralized control for DC microgrids (MG) has been developed and implemented. The proposed controller enables smooth transition between various operating modes. Finite state machine (FSM) has been used to mathematically describe the various operating modes (states), and events that may lead to mode changes (transitions). Therefore, the developed centralized controller aims at optimizing the performance of MG during all possible operational scenarios, while maintaining its reliability and stability. Results of selected cases have been presented. These results show stable transition between modes, verifying the validity and applicability of the proposed controller.

Optimizing Control Of Shell Eco-Marathon Prototype Vehicle To Minimize Fuel Consumption, Chad Louis Bickel

Master's Theses

Every year the automotive industry strives to increase fuel efficiency in vehicles. When most vehicles are designed, fuel efficiency cannot always come first. The Shell Eco-marathon changes that by challenging students everywhere to develop the most fuel-efficient vehicle possible. There are many different factors that affect fuel efficiency, and different teams focus on different vehicle parameters. Currently, there is no straightforward design tool that can be used to help in Shell Eco-marathon vehicle design. For this reason, it is difficult to optimize every vehicle parameter for maximum fuel efficiency.

In this study, a simulation is developed by using basic vehicle …

A Framework For Categorization Of Industrial Control System Cyber Training Environments, Evan G. Plumley

Theses and Dissertations

First responders and professionals in hazardous occupations undergo training and evaluations for the purpose of mitigating risk and damage. For example, helicopter pilots train with multiple categorized simulations that increase in complexity before flying a real aircraft. However in the industrial control cyber incident response domain, where incident response professionals help detect, respond and recover from cyber incidents, no official categorization of training environments exist. To address this gap, this thesis provides a categorization of industrial control training environments based on realism. Four levels of environments are proposed and mapped to Blooms Taxonomy. This categorization will help organizations determine which …

P26. Global Exponential Stabilization On So(3), Soulaimane Berkane

Western Research Forum

Global Exponential Stabilization on SO(3)