Electrical and Computer Engineering Commons^™

Limiting Maximum Drag Reduction Asymptote For The Moment Coefficient Of An Enclosed Rotating Disk With Fine Spiral Grooves, Budiarso Budiarso, Keizo Watanabe, Satoshi Ogata

Makara Journal of Technology

In this study, the limiting maximum drag reduction asymptote for the moment coefficient of an enclosed rotating disk with fine spiral grooves in turbulent flow region were obtained analytically. Analysis which were based on an assumption for a simple parabolic velocity distribution of turbulent pipe flow to represent relative tangential velocity, was carried out using momentum integral equations of the boundary layer. For a certain K- parameter the moment coefficient results agree well with experimental results for maximum drag reduction in an enclosed rotating disk with fine spiral grooves and drag reduction ratio approximately was 15 %. Additionally, the experimental …

Co2 Absorption From Its Mixture With Ch4 Or N2 Through Hollow Fiber Membrane Contactor Using Water As Solvent, Sutrasno Kartohardjono, Anggara Anggara, Subihi Subihi, Yuliusman Yuliusman

Makara Journal of Technology

CO2 Absorption from Its Mixture with CH4 or N2 through Hollow Fiber Membrane Contactor using Water as Solvent. Hollow fiber membrane contactors have been widely used as gas-liquid contactors recently such as in the CO2 absorption process from gas stream. This research aims to evaluate the effectiveness of hollow fiber membrane contactor to absorb CO2 from its mixture with CH4 or N2 using water through mass transfer and hydrodynamic tests. There are 3 membrane modules used in this research with shell diameter of 1.9 cm, length of 40 cm, outer fiber diameter of 2.7 mm and fiber number in the …

Reverse Link Cdma System Capacity Evaluation For Stratospheric Platform Mobile Communications, Iskandar Iskandar

Makara Journal of Technology

We propose an analysis of reverse link CDMA multispot beam stratospheric platforms (SPF) in this paper. The SPF is currently proposed as a novel wireless technology for the development of the next generation fixed and mobile communications. The geometry of this technology is different from that of the terrestrial but rather similar to the satellite based cellular system. However, evaluation on the CDMA system capacity of this technology has not been much reported. This paper addresses all possible multiple access interference analyses including the effects of channel fading and shadowing in order to evaluate the system capacity. Single SPF and …

The Potency Of Fire And Explosion Hazard On Premium Oil Storage Tank At Depot X 2007, Fatma Lestari, Warid Nurdiansyah

Makara Journal of Technology

The Potency of Fire and Explosion Hazard on Premium Oil Storage Tank at Depot X 2007. Premium oil storage tanks have fire and explosion risk because Premium oil is flammable liquid. Because of that, fire and explosion risk assessment on Premium oil storage tank at Depot X is needed as foundation to fire and explosion risk management, and comply with regulations. Method of this research is Dow’s Fire and Explosion Index. This research indicate that F&EI value for Premium oil storage tank is 118,82. Based on that F&EI value, level of risk at Premium oil storage tank is intermediate risk.

Analysis Of Three Phase Controlled Rectifier With The Same Distance Control As Compared To The Same Angle Control, Sudirman S., Sri Kurniati A.

Makara Journal of Technology

Analysis of three phase controlled rectifier with the same distance control as compared to the same angle control. This research aim to compare the firing of the same distance and the same angle control at three phase controlled rectifier with seen generated harmonic at input (AC side). Then calculate of rectifier efficiency and power factor comparison from both the control type. The rectifier use passive filter with resistance 11 ohm and is analysed with program simulation using PSPICE version 7.1. Result of research indicate that use of the same distance control generates the 5th and 7th harmonics, while the same …

The Use Of Red Cabbage’S Anthocyanine Extract As A Photosensitizer On A Dye-Sensitized Nanocrystalline Tio2 Solar Cell, Akhiruddin Maddu, Mahfuddin Zuhri, Irmansyah Irmansyah

Makara Journal of Technology

The use of Red Cabbage’s anthocyanine extract as a photosensitizer on a Dye-Sensitized Nanocrystalline TiO2 Solar Cell. A solid-state dye-sensitized nanocrystalline TiO2 solar cell utilizing anthocyanin extract form red cabbage as photosensitizer was fabricated. The solar cell was formed in sandwich structure, which two electrodes sandwiching polymer electrolyte containing a redox couple (I-/I3 -). One of the electrodes, namely working electrode, TiO2 layer on TCO (transparent conducting oxide) coated glass substrate was sensitized with anthocyanin dye as electron donor in the system. Another electrode was a carbon sheet as a counter electrode. Gel electrolyte based on PEG (polyethylene glycol) containing …

Effect Of Contact Time On Interface Reaction Between Aluminum Silicon (7% And 11%) Alloy And Steel Dies Skd 61, Bambang Suharno, Neni Octapiani Nurhayati, Bustanul Arifin, Sri Harjanto

Makara Journal of Technology

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11%) Alloy and Steel Dies SKD 61. Die soldering (die sticking) is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz …

College Of Engineering Senior Design Competition Spring 2007, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Biodesulphurization Within Natural Gas In Oil And Gas Field, Sri Astuti Rahayu, M. Fierdaus, Syafrizal Syafrizal, M. Udiharto

Makara Journal of Technology

The presence of sulphur compounds in natural gas can interfere to the quality of natural gas. The decline of combustion gas capacity, metal instrument corrosion in gas piping, and the environmental pollution from gas emission can affect by their presence. Bio-filter is one of the methods that selected to reduce sulphur content in natural gas. A lab scale study of hydrogen sulphide reduction in natural gas had conducted in oil and gas field using bio-filter method. The bio-filter system (±1 L volume) contains an active carbon and thiosulphide medium as a substrate, Thiobacillus thioparus as a single culture of sulphur …

Mechanical Study On Using Of Accr Thermal Conductor At 500 Kv Sutet, Suprihadi Prasetyono

Makara Journal of Technology

Mechanical Study on using of ACCR Thermal Conductor at 500 kV SUTET. At the height of electricity demand increasing recently, circumstance of environment more limited and also expense of high investment, making thermal conductor (conductor thermal resistance) considered to be one of alternative in the electricity transmission bottlenecks. These days it has been developed thermal conductor ACCR (Aluminium Conductor Composite Reinforced) which can operate with temperature up to 240oC, so that making the current carrying capacity being higher than conventional conductor. This research aimed to study load current leading to mechanical characteristic ACCR conductor included tension, length of elongation and …

Production Of Medium Chain Length Polyhydroxyalkanoates From Oleic Acid Using Pseudomonas Putida Pga1 By Fed Batch Culture, Sidik Marsudi, Irene K.P. Tan, Seng Neon Gan, K. B. Ramachandran

Makara Journal of Technology

Bacterial polyhydroxyalkanoates (PHAs) are a class of polymers currently receiving much attention because of their potential as renewable and biodegradable plastics. A wide variety of bacteria has been reported to produce PHAs including Pseudomonas strains. These strains are known as versatile medium chain length PHAs (PHAs-mcl) producers using fatty acids as carbon source. Oleic acid was used to produce PHAs-mcl using Pseudomonas putida PGA 1 by continuous feeding of both nitrogen and carbon source, in a fed batch culture. During cell growth, PHAs also accumulated, indicating that PHA production in this organism is growth associated. Residual cell increased until the …

Simple: System Automatic Essay Assessment For Indonesian Language Subject Examination, Anak Agung Putri Ratna, Bagio Budiardjo, Djoko Hartanto

Makara Journal of Technology

SIMPLE: System Automatic Essay Assessment for Indonesian Language Subject Examination. Evaluation of study of a student is a very important aspect of an educational process. Evaluation is aimed at measuring the level of student understanding of the given lecture materials. Measuring student understanding of the course material, using essay-type exam, is generally used as the evaluation tool. In this essay-type exam, the student has to answer questions using sentences, whereby choices of possible answers are not indicated. The student has to answer the questions with his/her sentences. The answers may vary, since it reflects the student’s best thoughts of the …

Utilization Of Bagasse Cellulose For Ethanol Production Through Simultaneous Saccharification And Fermentation By Xylanase, M. Samsuri, Misri Gozan, R. Mardias, M. Baiquni, Heri Hermansyah, Anondho Wijanarko, Bambang Prasetya, M. Nasikin

Makara Journal of Technology

Utilization of Bagasse Cellulose for Ethanol Production through Simultaneous Saccharification and Fermentation by Xylanase. Bagasse is a solid residue from sugar cane process, which is not many use it for some product which have more added value. Bagasse, which is a lignosellulosic material, be able to be use for alternative energy resources like bioethanol or biogas. With renewable energy resources a crisis of energy in Republic of Indonesia could be solved, especially in oil and gas. This research has done the conversion of bagasse to bioethanol with xylanase enzyme. The result show that bagasse contains of 52,7% cellulose, 20% hemicelluloses, …

Construction Of Short-Length High-Rates Ldpc Codes Using Difference Families, Deny Hamdani, Ery Safrianti

Makara Journal of Technology

Low-density parity-check (LDPC) code is linear-block error-correcting code defined by sparse parity-check matrix. It is decoded using the massage-passing algorithm, and in many cases, capable of outperforming turbo code. This paper presents a class of low-density parity-check (LDPC) codes showing good performance with low encoding complexity. The code is constructed using difference families from combinatorial design. The resulting code, which is designed to have short code length and high code rate, can be encoded with low complexity due to its quasi-cyclic structure, and performs well when it is iteratively decoded with the sum-product algorithm. These properties of LDPC code are …

Kinetic Model For Triglyceride Hydrolysis Using Lipase:Review, Heri Hermansyah, A. Wijanarko, Dianursanti Dianursanti, Misri Gozan, Praswasti P. D.K Wulan, Rita Arbianti, Roekmijati W. Soemantojo, Tania Surya Utami, Yuliusman Yuliusman, Momoji Kubo, Naomi Shibasaki Kitakawa, Toshiy Yonemoto

Makara Journal of Technology

Triglyceride hydrolysis using lipase has been proposed as a novel method to produce raw materials in food and cosmetic industries such as diacylglycerol, monoacylglycerol, glycerol and fatty acid. In order to design a reactor for utilizing this reaction on industrial scale, constructing a kinetic model is important. Since the substrates are oil and water, the hydrolysis takes place at oil-water interface. Furthermore, the triglyceride has three ester bonds, so that the hydrolysis stepwise proceeds. Thus, the reaction mechanism is very complicated. The difference between the interfacial and bulk concentrations of the enzyme, substrates and products, and the interfacial enzymatic reaction …

Sulfonation Of Cptfe Film Grafted Styrene For Proton Exchange Membrane Fuel Cell, Yohan Yohan

Makara Journal of Technology

Sulfonation of cPTFE Film grafted Styrene for Proton Exchange Membrane Fuel Cell. Sulfonation of γ-ray iradiated and styrene-grafted crosslinked polytetrafluoroethylene film (cPTFE-g-S film) have been done. The aim of the research is to make hydropyl membrane as proton exchange membrane fuel cell. Sulfonation was prepared with chlorosulfonic acid in chloroethane under various conditions. The impact of the percent of grafting, the concentration of chlorosulfonic acid, the reaction time,and the reaction temperature on the properties of sulfonated film is examinated. The results show that sulfonation of surface-grafted films is incomplete at room temperature. The increasing of concentration of chlorosulfonic acid and …

Heating Methods And Detection Limits For Infrared Thermography Inspection Of Fiber-Reinforced Polymer Composites, Jeff R. Brown, H. R. Hamilton

Publications

The use of fiber-reinforced polymer (FRP) composites to strengthen existing civil infrastructure is expanding rapidly. Many FRP systems used to strengthen reinforced concrete are applied using a wet lay-up method in which dry fibers are saturated on site and then applied to the surface. This research investigated using infrared thermography (IRT) as a nondestructive evaluation (NDE) tool for detecting air voids and epoxy-filled holes in FRP systems bonded to a concrete substrate. Four small-scale specimens with FRP thicknesses ranging from 1 to 4 mm (0.04 to 0.16 in.) containing fabricated defects were constructed and inspected in a laboratory setting. Three …

Characterization Of On-Road Petrol Vehicle Emissions Patterns In Dar Es Salaam City (Tanzania), Geoffrey John

Tanzania Journal of Engineering and Technology (TJET)

Motor vehicle emissions have been identified to be the major source of air pollution in most urban cities. It has serious impact on urban air quality and public health. The Governments of many countries need to adopt stringent vehicle emissions regulations to protect the air quality, the undertaking of which can only be implemented once the problem at hand is known. In the present study, the characteristics of on road vehicle emissions from the selected local ar~as at the city of Dar es Salaam in a developing country for in-use petrol vehicles for urban driving conditions ranging from idling, lOkm/h …

2006 Fall Engr333 Project Final Report, 2006 Fall Engr333

ENGR 333

The objective of this project was to demonstrate Calvin’s interest in alternative energy. The development of a short-term plan to implement a demonstration wind turbine and a long-term plan to determine the feasibility of a larger turbine for the future demonstrates this interest. The class was divided into five teams: management, external relations, long-term technology, short-term technology, and campus infrastructure. While each team had its own objectives, everyone worked together to share information and accomplish the overall project goals. This management technique provided necessary structure and simulated an environment typically found in a career environment.

College Of Engineering Senior Design Competition Fall 2006, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

2006 Fall Engr333 Project Posters, 2006 Fall Engr333

ENGR 333

To demonstrate Calvin’s interest in alternative energy by developing a short-term plan to implement a demonstration wind turbine and a long-term plan to determine the feasibility of a larger turbine for the future.

Biogasoline Production From Palm Oil Via Catalytic Hydrocracking Over Gamma-Alumina Catalyst, Anondho Wijanarko, Dadi Ahmad Mawardi, Mohammad Nasikin

Makara Journal of Technology

Biogasoline Production from Palm Oil Via Catalytic Hydrocracking over Gamma-Alumina Catalyst. Bio gasoline conversion from palm oil is an alternative energy resources method which can be substituted fossil fuel base energy utilization. Previous research resulted that palm oil can be converted into hydrocarbon by catalytic cracking reaction with γ-alumina catalyst. In this research, catalytic cracking reaction of palm oil by γ-alumina catalyst is done in a stirrer batch reactor with the oil/catalyst weight ratio variation of 100:1, 75:1, and 50:1; at suhue variation of 260 to 340oC and reaction time variation of 1 to 2 hour. Post cracking reaction, bio …

Segmental Sinusoidal Model For Speech Signal Coding, Florentinus Budi Setiawan, Soegijardjo Soegijoko, Sugihartono Sugihartono, Suhartono Tjondronegoro

Makara Journal of Technology

Segmental Sinusoidal Model for Speech Signal Coding. Periodic signal can be decomposed by sinusoidal component with Fourier series. With this characteristic, it can be modeled referring by sinusoidal form. By the sinusoidal model, signal can be quantized in order to encode the speech signal at the lower rate. The recent sinusoidal method is implemented in speech coding. By using this method, a block of the speech signal with 20 ms to 30 ms width is coded based on Fourier series coefficients. The new method proposed is quantization and reconstruction of speech signal by the segmental sinusoidal model. A segment is …

A Study On Parallel Computation Tools On Networked Pcs, Heru Suhartanto

Makara Journal of Technology

A Study on Parallel Computation Tools on Networked PCs. Many models for natural phenomena, engineering applications and industries need powerfull computing resources to solve their problems. High Performance Computing resources were introduced by many researchers. This comes in the form of Supercomputers and with operating systems and tools for development such as parallel compiler and its library. However, these resources are expensive for the investation and maintenance, hence people need some alternatives. Many people then introduced parallel distributed computing by using available computing resource such as PCs. Each of these PCs is treated as a processors, hence the cluster of …

Crude Oil Sludge Degradation In Microcosmic Scale: Simple Simulation As Preliminary Study On Land Treatment Bioremediation., Astri Nugroho

Makara Journal of Technology

Crude Oil Sludge Degradation in Microcosmic Scale: Simple Simulation as Preliminary Study on Land Treatment Bioremediation. A study in microcosmic condition has been carried out to evaluate the bacterial hydrocarbonoclastic capability in increasing the oil sludge degradation being mixed with NPK fertilizer as nitrogen resources. Aerobic test was carried out by putting erlenmeyers in a shaker incubator, 120 rpm shaking speed, at 50°C temperature. While 150 days in microcosmic one observation showed that the consortium has the potential to grow up to 50% (v/v) sludge oil load. Maximum growth and maximum growth rate of the consortium occurred in the III …

Determination Of Operation Condition And Product Dimension Accuracy Optimization Of Filament Deposition Modelling On Layer Manufacturing Application, Slamet A. Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santoso Budi Rochardjo

Makara Journal of Technology

Layer manufacturing process has proven as a process that can produce a high complexity mechanical part. Now, Improvement of LM methods continuously conduct that is aimed to increase precessions and efficiency of these processes. Pressure filament deposition modelling is a form of layer manufacturing process that is designed to produce a plastic part with controlling its semisolid phase. In this research, the equipment of filament depositor is designed and tested to make the product filament deposition. With operation condition observation, the optimal temperature and pressure of deposition process was determined. These experiments used PVC as crystalline material and polypropylene as …

Magnetic Field Effects On Caco3 Precipitation Process In Hard Water, Nelson Saksono, Setijo Bismo, Elsa Krisanti, Azwar Manaf, Roekmijati Widaningrum

Makara Journal of Technology

Magnetic Field Effects on CaCO3 Precipitation Process in Hard Water. Magnetic treatment is applied as physical water treatment for scale prevention especially CaCO3, from hard water in piping equipment by reducing its hardness. Na2CO3 and CaCl2 solution sample was used in to investigate the magnetic fields influence on the formation of particle of CaCO3. By changing the strength of magnetic fields, exposure time and concentration of samples solution, this study presents quantitative results of total scale deposit, total precipitated CaCO3 and morphology of the deposit. This research was run by comparing magnetically and non-magnetically treated samples. The results showed an …

Stress Corrosion Cracking Behavior Of Stainless Steel 304 In The Sulfuric Acid Environment Due To Prestrain, Mohammad Badaruddin, Ahmad Suudi, Arinal Hamni

Makara Journal of Technology

Stress Corrosion Cracking Behavior of Stainless Steel 304 in the Sulfuric Acid Environment Due to Prestrain. The aim of research is to investigate the effect of prestrain on the stress corossion cracking behavior of AISI 304 stainless steel in the sulfuric acid of 10% concentration under the static cantilever loading according to ASTM E-1681 standart. The specimen of 304 Stainless steel was strain up over the yield strength until reaching the uniform strain of 5% and 10% using servopulser UTM 9506 under the displacement control of 0,3 mm/sec. The results of test show that the prestrain of 5% specimen is …

Using Coupled Eulerian And Lagrangian Grids To Model Explosive Interactions With Buildings, Braden Lusk, William P. Schonberg, Jason Baird, Robert S. Woodley, Warren Noll

Mining Engineering Faculty Research & Creative Works

This paper presents the development of a computational model that can be used to study the interactions between structures and detonating explosives contained within them. This model was developed as part of an effort to develop a rubble characterization model for use in AmmoSIM, an agent based urban tactical decision aid (UTDA) software for weapon-target pairing. The rubble pile created following the collapse of a building in a combat situation can significantly impact mission accomplishment, particularly in the area of movement and maneuver. The information provided by AmmoSIM will enable both platoon level and command center staff to make informed …

2006 Fall Engr333 Project Assignment, Matthew K. Heun

ENGR 333

In the Fall 2006 semester, I challenged the ENGR333 students to “construct a realistic plan to make a significant impact on the Calvin College campus with electrical power generated from wind resources.”

Customer

The customer for this project was Calvin’s VP for finance Henry DeVries.