Electrical and Computer Engineering Commons^™

Methodology For Calculating The Technical And Economic Indicators Of A Photovoltaic Thermal Installation Based On A Thin-Film Cadmium Telluride Module, Islom Rakhmatovich Jurayev, Isroil Abriyevich Yuldoshev, Zukhra Islamovna Jurayeva

Technical science and innovation

This article presents a methodology for calculating the technical, economic and environmental indicators of the developed design of a photovoltaic thermal installation with a nominal electric power of 1,2 kW and a thermal power of 2.17 kW for simultaneous production of electric energy and hot water for household needs of consumers. The capacity of the installation is 5.26 kWh of electricity and 30 liters/hour of heated water. The schemes of obtaining hot water by additional heating of the heated water produced by the installation in the cool seasons of the year are presented. This installation allows to receive total energy …

Study Of The Physical-Chemical Properties Of Chitosan Synthesized By The Cryogenic Method From Apis Mellifera Bees, Dilnoza Sohibovna Isomitdinova, Gulnora Akmalovna Ikhtiyarova, Jahongir Mustaqim O’G’Li Sharopov

Technical science and innovation

Chitosan was synthesized from Apis Mellifera dead bees by traditional and cryogenic methods, and the degree of deacetylation, viscosity, and molecular mass of the synthesized sample was studied. Chitosan was synthesized by deacetylation of chitin under cryogenic conditions. NaOH concentration 40%, temperature 90 ± 3 °C, time 120 min. The degree of deacetylation, and molecular mass was determined using an Ubbelode viscometer. DDA was determined by conductometric titration under standard conditions. The degree of deacetylation of Apis Mellifera chitosan was 87%. synthesized by cryogenic method DDA of chitosan was 83% synthesized by traditional method. Conducting the synthesis in liquid nitrogen …

Development Of A Universal Humidity Converter At Ultra High Frequency, Hulkar Asadullayevna Usmonova, Asadulla Turgunbayev

Technical science and innovation

The article proposes the and principle of operation of a universal primary measuring transducer of humidity at an ultra-high frequency with reciprocating motion along the vertical axis of rotation, which allows increasing the information redundancy of the primary measuring transducer (the influence of inhomogeneities, including humidity in the composition of the material, on the measurement result is averaged). The design of the primary measuring transducer under consideration provides for correction of the moisture measurement result by the mass (density) of the material, which will make it possible to carry out measurements without preliminary weighing the sample. The obtained results of …

Analysis Of The Drives Of Pumping Stations In The Southern Part Of The Angren Coal Mine Of Uzbekugol Jsc, Shukhrat Badretdinovich Umarov, Murakam Mirzakhmatovich Mirsaidov, Islombek A’Lobekovich Abdullabekov, Saidamirkhon Hayrullakhon O‘G‘Li Oripov

Technical science and innovation

This article presents the results of a comprehensive analysis of the operation of pumping station drives in the southern part of the Angren coal mine of Uzbekugol JSC. The modes of operation and designs of pumps of various types are considered, including СPSH 850-240, D320-50, D1200-125 and GR170-30. The study covers the performance characteristics of these pumps, as well as their adaptation to the specific conditions of the coal mine. Special attention is paid to the impact of climate change on the operating modes of pumping units. Changes in the amount and intensity of precipitation, as well as fluctuations in …

Impulse, Fall 2024, Jill Fier, Micayla Standish, Jerome J. Lohr College Of Engineering

Impulse (Jerome J. Lohr College of Engineering Publication)

2 | Math Teacher Counts Her Blessings
3 | New Roles for Burckhard
4 | Three New Department Heads
6 | New Faculty and Staff
8 | Taking Engineering on The Road
10 | Dennis Helder Named Distinguished Alum
12 | Mccomish Endowment Making an Impact
14 | Innovate Sodak Supports Local Projects
16 | R1 the SDSU Way
18 | Nation’s Top Civil Engineering Student Chapter
22 | Hunter Wallster Setting Records
24 | Jenna Currier: When Passion Meets Talent
28 | Student Teams Compete
30 | RASC-AL Team Overcomes Setback
32 | Break the Ice Team Comes Home …

Design Of An Above Pavement Wireless Sensor Node (Apwsn) For Real-Time Roadway Monitoring Using Piezoelectric Energy-Harvesting, Jochy Jonathan Perez

Theses and Dissertations

The evolution of Smart Highway and Internet of Things (IoT) technologies offers new opportunities to improve the safety and efficiency of vehicular traffic on roads. This research effort describes the development of a wireless pavement sensor that provides a novel method to detect key pavement parameters while incorporating low-power energy harvesting that leverages the kinetic energy generated by vehicular traffic. The Above Pavement Wireless Sensor Node (APWSN) is the embodiment of the approach. APWSN can facilitate the strategic deployment of sensors on a wide variety of roads to enable real-time data collection to support decision-making processes for road infrastructure maintenance …

Design Frameworks For Ventilative Cooling: Perceptions From Building Design Practitioners In Ireland And The United Kingdom, Maha Sohail, Adam O'Donovan, Paul D. O'Sullivan

Publications

The global increase in building cooling demands poses a challenge for designers striving for net zero energy consumption. The prevalent use of mechanical cooling underscores the necessity for designers to consider Ventilative Cooling as a viable alternative in the early stages of building design. This paper presents findings from an exploratory survey and semi-structured interviews of industry experts in Ireland and the United Kingdom about their design processes and experienced-based approaches to designing Ventilative Cooling. The findings suggest that the pre-design stage has the same influence for promoting ventilative cooling strategies as the schematic and detailed design stages for practitioners, …

Estimation Of Vehicle Traffic Parameters Using An Optical Distance Sensor For Use In Smart City Road Infrastructure, Rafał Burdzik, Ireneusz Celiński, Minvydas Ragulskis, Vinayak Ranjan, Jonas Matijošius

Henry M. Rowan College of Engineering Departmental Research

In recent decades, the dynamics of road vehicle traffic have significantly evolved, compelling traffic engineers to develop innovative traffic monitoring solutions, especially for dense road networks. Traditional methods for measuring traffic volume along road sections may no longer suffice for modern traffic control systems. This is particularly true for induction loops, a widely used method since the last century. In contrast, measuring techniques using microwaves or visible light offer better accuracy but are often hindered by the high cost of sensors. This paper presents new techniques for measuring traffic flow and other parameters that adapt to changing traffic dynamics using …

Remote Vibration Based Monitoring Of Bridge Scour, Alan Kazemian

Dissertations

The gradual erosion of the sediment around a bridge foundation is called Scour. This erosion is caused by water flow and increases during times of high-water flow such as flooding. The scour leaves the bridges structurally unsound over time and jeopardizes the safety of the structure. Approximately 60 percent of bridge failures in the United States are caused by scour. A variety of types of devices have been used to detect scour. Most of these devices only observe the scour and not the structural integrity of the bridge. The typical approach has relied on visual inspections of the bridges after …

Exploring The Impact Of Artificial Intelligence On Project Management Across The Manufacturing, Technology, And Construction Industries, Susie Diaz Ferrera

Harrisburg University Dissertations and Theses

This study explores the impact of Artificial Intelligence (AI) on project management across the manufacturing, technology, and construction industries. The research focuses on understanding the benefits, challenges, and long-term implications of AI utilization in these sectors. Key findings indicate that 46% of participants use AI mainly for task automation and enhancing functions like brainstorming and communication, which significantly boosts efficiency and team productivity. Despite these benefits, the research identifies several obstacles, including high initial costs, inadequate training, technical issues, and unclear regulatory guidelines. The study addresses four main questions, revealing that AI not only enhances project management processes but also …

Electrical Design For Moringa Leaf Dryer, Jake Weiss

Construction Management

The objective of this project is to provide a methodology to the electrical scope of mechanical leaf dryers. This dryer was particularly designed for an off-grid farm in New Longoro, Ghana in which resources and materials are limited. The electrical system must be designed so that it works with motors, variable frequency drives, worm gears, and other materials that could be sourced in Ghana. The system should also draw minimal power so that remaining photovoltaic energy could be utilized on the farm. The system should be simplistic and repeatable for other farmers to utilize. By using both a numerical analysis …

Estimation Of Useful-Stage Energy Returns On Investment For Fossil Fuels And Implications For Renewable Energy Systems, Emmanuel Aramendia, Paul E. Brockway, Peter G. Taylor, Jonathan B. Norman, Matthew K. Heun, Zeke Marshal;

University Faculty Publications and Creative Works

The net energy implications of the energy transition have so far been analysed at best at the final energy stage. Here we argue that expanding the analysis to the useful stage is crucial. We estimate fossil fuelsʼ useful-stage energy returns on investment (EROIs) over the period 1971–2020, globally and nationally, and disaggregate EROIs by end use. We find that fossil fuelsʼ useful-stage EROIs (~3.5:1) are considerably lower than at the final stage (~8.5:1), due to low final-to-useful efficiencies. Further, we estimate the final-stage EROI for which electricity-yielding renewable energy would deliver the same net useful energy as fossil fuels (EROI …

Regular Algorythms For Synthesis Of Optimal Control Systems For Dynamic Objects, Igamberdiyev Husan, Uktam Farkhodovich Mamirov, Xankeldiyeva Zebiniso

Technical science and innovation

The article presents algorithms for the synthesis of an optimal control system for dynamic objects. As a model, we consider a differential equation of a continuous one-dimensional system in the form of a state space, which has the properties of controllability and observability. The paper shows the need to use an observation device in order to assess how the properties of the controlled system change with the slightest change in the parameters of the control object, to assess the sensitivity of the system to these changes. When finding a solution to the equation formulated to find the parameters of the …

Studying The Production Of Nanocelluloses, Shohzodbek Abduvahobovich Rashidov, Elmurod Abduqodirovich Egamberdiev, Sadritdin Maxamatdinovich Turabdjanov

Technical science and innovation

Nanoscience is a broad field that includes nanophysics and nanochemistry. Nanotechnologies are aimed at obtaining nanoparticles with new properties and creating materials and devices based on them. This is one of the modern trends in the development of science in the 21st century.

Based on the study of information about nano-sized materials, the mechanisms of their production and changes in their properties, we will consider the technology for producing nanocellulose from organic substances, i.e. from cellulose. The article describes a technology that examines devices for producing nanocellulose and the principles of their operation, as well as a combined method of …

Comparative Analysis Of Cutting Forces In Axial-Compliant And Rigid Chamfering Tools, Sultonmurod Bekpulatovich Normatov, Oybek Tuyboyov, Azimjon Axror O'G'Li Pardayev, Alisher G‘Ayratjon Ogli Boratov, Shohjahon Tuxtasin Ogli Abdullayev

Technical science and innovation

This study delves into the analysis of cutting forces in axial-compliant systems, focusing specifically on the comparison between axially spring-compensated 90° conical tools and rigid chamfering tools. The research incorporates a predictive model for chamfer size calculation in the axially spring-compensated tools, verified through experimental tests on representative parts. The study aims to control chamfer size within tolerances by adjusting process conditions and optimizing processing efficiency. By exploring the fundamentals of the chamfering process, this research offers insights into breaking sharp edges on components with positional errors and shape deformations, with a particular emphasis on aero-engine casings. The integration of …

Reducing Glass Loss During Transportation And Storage, Abdulaziz Muzafarovich Qurbanov, Mirzaabdullayev Jaxongir Baxtiyorovich

Technical science and innovation

The article discusses the processes of transportation and storage of sheet glass in the production of protective glass for cars. The experience of organizing the transportation and storage of glass in developed countries of the world was analyzed in order to study the problems of losses of raw materials during the transportation and storage of laminated glass, as well as to develop and approve a regulatory and technical document. in this field. The supplies of various brands of polished laminated glass used in the production of protective glass for cars to Avtooina LLC from different addresses, from different manufacturers were …

Ferroresonance In Three-Phase Electrical Networks, Shavkat Ernstovich Begmatov

Technical science and innovation

Possible modes of ferroresonance in three-phase electric networks and analysis of substitution schemes where ferroresonance voltage increase is observed are considered. The most complete magnetization curve of the transformer core and the analysis of the generalized equivalent substitution scheme are presented, as a result of which more accurate formulas for determining the values of equivalent parameters of the electrical network and voltage transformer in ferroresonance mode are obtained. Factor of ferroresonance voltage increase is introduced, which determines ratio between amplitude values of transformer phase voltage and mains voltage. The method of determination of boundary conditions of steady ferroresonance voltage increase …

Main Prospects Of Natural Gas Purification Technologies From Acidic Compounds, Oybek Yusupdjanovich Aripdjanov, Diyora Zokhid Qizi Khayrullaeva, Jonibek Avazek Ogli Abdumuminov

Technical science and innovation

The article discusses the main prospects for the technology of purifying natural gas from acidic components and the problems of ensuring the purity of oil and gas products in accordance with state standards. An increase in the degree of purification from H₂S, CO₂, elemental sulfur, carbonyl sulfide, ethyl mercaptans (thiols), methyl mercaptan, carbon disulfide, sulfides, disulfides (dithioethers), thiophene, sulfoxides and sulfones is considered. Also, the physicochemical properties of the absorbent for the purification of sulfur compounds (generated during natural gas processing) are studied. Based on the study of various absorbents (ethanolamine (EA), methylethanolamine (MEA), diethanolamine (DEA), …

Use Of Mathematical Skills For Technical Condition Assessment Of Power Autotransformers, Dilafruz Rustamjon Qizi Abdullabekova, Nurali Berdiyorovich Pirmatov

Technical science and innovation

In this paper, we review innovative approaches to assess the technical condition of autotransformers using mathematical methods. The main purpose of these methods is to increase the efficiency of diagnostics and prevent possible failures in power systems. The developed mathematical expression is based on complex data analysis, application of statistical methods and machine learning technologies. This makes it possible to achieve more accurate and earlier detection of potential problems. As a result of these innovative approaches, the possibilities for early detection and prevention of faults are significantly increased. This is important for ensuring the smooth operation of power systems and …

Quantitative Assessment And Characterization Of Tool Wear Phenomena In Advanced Manufacturing Processes, Oybek Valijonovich Tuyboyov

Technical science and innovation

This paper explores the quantitative assessment and characterization of tool wear phenomena in advanced manufacturing processes, employing a multifaceted approach encompassing traditional measurements, image processing, machine learning, and predictive modeling. The study emphasizes the intricate dynamics of tool wear and its direct impact on cutting tool performance, addressing challenges in real-time monitoring and optimization of machining operations. Traditional methods like VBmax measurement are juxtaposed with advanced techniques such as the improved conditional generative adversarial net with a high-quality optimization algorithm (CGAN-HQOA), efficient channel attention destruction and construction learning (ECADCL), and shape descriptors based on contour, moments, orientations, and texture. Artificial …

Implementing A Solar Photovoltaic Station In Watering Systems Utilizing Complex Software, Akbarxon Sarvar O'G'Li Uroqov, Faxriddin Jaylovovich Nosirov, G'Olibjon Pardayevich Arzikulov, Zarina Amriddin Qizi Sayfutdinova

Technical science and innovation

This article explores the benefits of transitioning from traditional agricultural irrigation systems to more cost-effective alternatives powered by renewable energy sources. By integrating solar photovoltaic technology into irrigation processes, significant reductions in resource wastage, estimated at 45-50%, are achievable through the implementation of drip irrigation techniques. This results in enhanced agricultural productivity. Moreover, the utilization of solar panels in green zones mitigates surface temperature increases, contributing to a 2-5% boost in electricity production. Currently, irrigation facilities primarily rely on the main energy grid. However, transitioning to renewable energy sources decreases reliance on non-renewable fuels, reduces greenhouse gas emissions, and fosters …

Selective Oxidation Of Iron In Chalcopyrite For Enhanced Copper Recovery, Khojiakbar Shuxrat O'G'Li Sultonov, Shokhrukh Toshpulatovich Khojiev, Gulnoza Berdiyor Qizi Beknazarova, Malika Sayfullayevna Saidova

Technical science and innovation

This study explores the thermodynamic feasibility of selectively oxidizing iron contained in chalcopyrite mineral while preventing the oxidation of copper sulphide, with the ultimate goal of enhancing the copper concentration in the sulphide concentrate. A redox reaction in the solid phases between chalcopyrite and copper (I) oxide was constructed and subjected to thermodynamic analysis. The research identifies a crucial temperature range of 498-598 K (225-325 °C) as the most favourable for the redox reaction. The equilibrium constants at the selected optimal temperatures, 1.152 for chalcopyrite and 1.137 for copper (I) oxide, indicate that the redox reaction adheres to the expected …

Solving Water Resources Problems - Water Saving In The Republic Of Uzbekistan, Rustam Muxammatdjanovich Raximov

Technical science and innovation

In this article we will talk about the problems of water resources in the Republic of Uzbekistan. The problem of drinking water supply, solutions to provide drinking water to the population of Uzbekistan. The largest consumers of fresh water in Uzbekistan are farmers. Due to outdated infrastructure, 40% of water is wasted. Rising food prices and the risk of spreading disease are the first signs of water shortages that we may experience in the coming еars. Uzbekcosmos told how to solve the problem. Water is an invaluable resource used not only in the home, but also in the production and …

Modelling Of Heat Transfer In An Air Solar Collector, Shakhnoza Abduvaxitovna Sultanova, Jasur Esirgapovich Safarov, A.A. Mambetsheripova

Technical science and innovation

This study is the prediction, depending on time and different geographical and climatic situations, of different operating parameters: solar radiation, ambient and outlet coolant temperature, heat exchange coefficients and losses. All these determine, in the absence of measurements, the efficiency of the system modelled with existing models with respect to these parameters. These models are usually compared with experimental results. Before modelling, it is necessary to investigate the different heat transfer and exchange regimes that exist between the different elements of this system in order to eventually have a system of equations governing this exchange. The modelling principle is to …

A Study On The Influence Of Cutting Parameters On Surface Roughness And Visualization Through Contour Plots And 3d Surface Profiles, Zayniddin Nosirovich Muxiddinov

Technical science and innovation

This research investigates the intricate relationship between cutting parameterscutting speed, feed rate, and depth of cut and surface roughness in machining processes. Surface roughness is a key determinant of machined surface quality, and optimizing cutting parameters is crucial for achieving superior finishes. Employing advanced visualization techniques, including contour plots and 3D surface profiles, the study offers a comprehensive exploration of surface topography dynamics. Statistical analyses and regression modeling enhance the quantitative understanding of how cutting parameters interact to shape surface roughness. The research affirms the significant influence of cutting speed, feed rate, and depth of cut, providing practical insights for …

Theory Of Development And Improvement Of The Mathematical Model Of The Methodology Of Public Control In The Management Of Occupational Safety And Industrial Risks, Aliakbar Khamidullaevich Rasulev, Sunnatilla Suleymanovich Suleymanov, Nodira Bakhadirzhanovna Gaibnazarova

Technical science and innovation

The article develops and analyzes a mathematical model based on a logical flowchart of the methodology of public control in the management of occupational safety and industrial risks and probability theory, according to the model, the results of compliance with the requirements of social cooperation on occupational safety lead to a sharp increase in the probability of reliability, management efficiency becomes higher. Analysis of the mathematical model of the developed logical flowchart based on probability theory has shown that when the parties cooperate to monitor the results of compliance with labor protection requirements, they lead to a sharp increase in …

Research Of The Influence Of Dust On Photovoltaic Modules, Anvarjon Mirolimov, Xalmurat Iliev

Technical science and innovation

The influence of dust concentrations on the current-voltage characteristics (voltampere characteristics) of photovoltaic modules (PVM) based on crystalline silicon in laboratory conditions. It was investigated how an uncleaned panel affects the output power. The tests were carried out in the city of Tashkent on the territory of the “National Research Institute of Renewable Energy Sources”. The objects were located co-plurally as specified in GOST R 60904-1 Photoelectric devices. Part 1. Measurement of current-voltage characteristics. Measurements of a cleaned photovoltaic module with a maximum power of 330 W and not a cleaned one of 236 W were obtained. Based on the …

Watercave: Virtual Reality For Engaging The Next Generation In Wastewater Management, Leeza Duller

Graduate Student and Postdoctoral Fellow Symposium

Within the next five to ten years, a significant portion of water and wastewater personnel are expected to retire, posing a substantial challenge for the utilities industry. The potential shortage of experienced workers poses inherent risks to the continuity of water services. WaterCAVE emerges as one of several tools designed to address this impending issue by engaging and inspiring the next generation to consider careers in the wastewater industry. This virtual reality (VR) simulation utilizes a ten-sided immersive display and was designed using Unity's 3D real-time development platform. Students from various educational levels, ranging from Pre-K to 12, are invited …

Modeling Recovery Of The Florida Electric Transmission Grid After Severe Weather Event, Wei B. Guan

Theses and Dissertations

Predicted changes to the climate are expected to increase the frequency and severity of extreme weather events. The Florida electric grid is a critical infrastructure system susceptible to severe weather events, especially hurricanes, causing widespread damage and outages. A foundational concept of the electric grid’s resilience is its ability to recover after extreme weather events, such as hurricanes and flooding. The recovery of the electrical grid after an extreme event is predicated upon the electrical asset's remoteness and the component's level of damage. Using fragility analysis, previous models have assessed the mean time to recover for transmission towers and substations …

Life Cycle Analysis Of Mobile Nuclear Reactor Compared To Other Alternative Fuels In Indopacom, Maria J. Hurtado

Theses and Dissertations

Energy is an item that makes the military vulnerable as it is something that they depend on the most which can have negative impacts. Mobile nuclear reactors are gaining the interest of many leaders in the military as a viable option of a potential alternative fuel source. There are many positives in utilizing mobile nuclear reactors in terms of environmental impacts and feasibility of transport. Studies have shown that mobile nuclear reactors can produce very low or negligible carbon emissions during operations. The focus of this thesis is to determine the environmental impacts of nuclear reactors, logistical requirements, and determine …