Computer Engineering Commons^™

Tolerance Specification Of Robot Kinematic Parameters Using An Experimental Design Technique, Y.H. Andrew Liou, Paul P. Lin, Richard R. Lindeke, Hsiang-Dih Chiang

Mechanical Engineering Faculty Publications

This paper presents the tolerance specification of robot kinematic parameters using the Taguchi method. The concept of employing inner and outer orthogonal arrays to identify the significant parameters and select the optimal tolerance range for each parameter is proposed. The performance measure based on signal-to-noise ratios (S/N) using the Taguchi method is validated by Monte Carlo simulations. Finally, a step-by-step tolerance specification methodology is developed and illustrated with a planar two-link manipulator and a five-degree-of-freedom Rhino robot.

The Application Of Neural Networks To Optimal Robot Trajectory Planning, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

Interpolation of minimum jerk robot joint trajectories through an arbitrary number of knots is realized using a hardwired neural network. Minimum jerk joint trajectories are desirable for their similarity to human joint movements and their amenability to accurate tracking. The resultant trajectories are numerical rather than analytic functions of time. This application formulates the interpolation problem as a constrained quadratic minimization problem over a continuous joint angle domain and a discrete time domain. Time is discretized according to the robot controller rate. The neuron outputs define the joint angles (one neuron for each discrete value of time) and the Lagrange …

Suboptimal Robot Joint Interpolation Within User-Specified Knot Tolerances, Daniel J. Simon, Can Isik

Electrical and Computer Engineering Faculty Publications

Approximation of a desired robot path can be accomplished by interpolating a curve through a sequence of joint-space knots. A smooth interpolated trajectory can be realized by using trigonometric splines. But, sometimes the joint trajectory is not required to exactly pass through the given knots. The knots may rather be centers of tolerances near which the trajectory is required to pass. In this article, we optimize trigonometric splines through a given set of knots subject to user-specified knot tolerances. The contribution of this article is the straightforward way in which intermediate constraints (i.e., knot angles) are incorporated into the parameter …

Robot Force Velocity Control Using Expert System For Control Mode Changes, William R. Doggett

Electrical & Computer Engineering Theses & Dissertations

The most important property of an automated mechanical system is reliable execution of a specified task. Automated mechanical systems work best in precisely structured environments where all operations are repeatable. Typically, these systems are difficult to modify and expensive to install. Sensors can be used to detect disturbances, thus reducing hardware cost by offsetting the need for precise rigid construction components. Sensors, however, increase the complexity and cost of the control software. Efficient methods of reacting to sensor information during automated system operation are required to reduce software complexity and expense.

This thesis analyzes a robotic construction task and describes …

Matching Points To Lines: Sonar-Based Localization For The Psubot, Kevin Blythe Stanton

Dissertations and Theses

The PSUBOT (pronounced pea-es-you-bought) is an autonomous wheelchair robot for persons with certain disabilities. Its use of voice recognition and autonomous navigation enable it to carry out high level commands with little or no user assistance. We first describe the goals, constraints, and capabilities of the overall system including path planning and obstacle avoidance. We then focus on localization-the ability of the robot to locate itself in space. Odometry, a compass, and an algorithm which matches points to lines are each employed to accomplish this task. The matching algorithm (which matches "points" to "lines") is the main contribution to this …

An Efficient Technique For Finding The Desired Global Optimum Of Robotic Joint Displacement, Paul P. Lin, An-Jen J. Yang

Mechanical Engineering Faculty Publications

For an industrial robot on a daily operation basis such as pick and place, it is desired to minimize the robotic joint displacements when moving the robot from one location to another. The objective of the optimization here is to simultaneously minimize a robot end effector's positional error and the robotic joint displacements. By modifying the searching algorithm in the existing complex optimization method, this article presents a technique for finding the desired global optimum solution more efficiently. To compare the optimum searching capability between the proposed and existing searching algorithms, a modified Himmelblau's function is used as an objective …

An Intelligent Database For Psubot, An Autonomous Wheelchair, Dieudonne Mayi

Dissertations and Theses

In the design of autonomous mobile robots, databases have been used mainly to store information on the environment in which the device is to operate. For most of the models and ready systems, the database when used, is not a stand alone component in the system, rather it is only intended to keep static information on the disposition and properties of objects on the map.

In this thesis is implemented an intelligent database. It combines static facts to build more information. An intelligent database such as this one will be a plus for an intended autonomous machine such as the …

Low To Medium Level Image Processing For A Mobile Robot, Cecilia H. Espinosa

Dissertations and Theses

The use of visual perception in autonomous mobile systems was approached with caution by mobile robot developers because of the high computational cost and huge memory requirements of most image processing operations. When used, the image processing is implemented on multiprocessors or complex and expensive systems, thereby requiring the robot to be wired or radio controlled from the computer system base.

Hereby developed is a simple, inexpensive and automatic image processing subsystem that is completely implementable on a PC-386SX with 640K base memory. The subsystem will serve as the front end of the vision system for the PSUBOT, an autonomous …

An Improved Method For Online Calculation And Compensation Of The Static Deflection At A Robot End-Effector, Paul P. Lin, Hsiang-Dih Chiang, Xiu Xun Cui

Mechanical Engineering Faculty Publications

Traditionally, robotic deflection analysis for a low-weight robot has been performed based on an assumption that each link is treated as a cantilever beam, which leads to no angular deflection at a joint. In practice, a robotic intermediate joint is linearly and angulary deflected when a load is applied at the end-effector. It is found in this study that the additional link deflection resulting from the angular deflection of a robotic revolute joint substantially contributes to the end-effector's total deflection. This article presents an improved method via a combination of classical beam theory, energy methods and the concepts of differential …

A Detailed Analysis Of Dynamic Robotic Simulation, Lonnie J. Love

Mechanical & Aerospace Engineering Theses & Dissertations

Future space missions may require the utilization of automation technology for assembly, maintenance, repair, and a variety of repetitive or hazardous operations. Many tasks which are likely candidates for robotic or telerobotic execution are either difficult or impossible to duplicate in the laboratory. With an accurate simulation package, many of these tasks can be evaluated by computer simulation before committing the resources required for laboratory experimentation. With this motivation, the ROBSIM robot simulation software has been developed by NASA Langley Research Center in conjunction with the Martin Marietta Corporation. ROBSIM is a versatile tool with features including the ability to …

Impacts Of Industrial Robotics: Potential Effects On Labor And Costs Within The Metalworking Industries, Steven M. Miller

Research Collection School Of Computing and Information Systems

According to leading expert opinion, industrial robots are among the most important innovations of recent decades. Yet there is very considerable uncertainty (and disagreement) as to the rate at which the use of robots will spread and what their effects on employment, costs, and market structure will be. As stressed in 1983 by Congress’s Office of Technology Assessment: “A central question for an analysis of the social and economic impacts of programmable automation is whether programmable automation is likely to spread especially rapidly among firms and industries, and why.” The author analyzes the job displacement effects of industrial robots, as …

Two Dimensional And Three Dimensional Path Planning In Robotics, Hyun Suk Kim

Dissertations and Theses

A methodology for 2D and 3D collision free path planning algorithm in a structured environment is presented. The isolated free convex areas are represented as a nodes in a graph, and a graph traversal strategy that dynamically allocates costs to graph path is used. Modification of the algorithm for small computational time and optimality is discussed. The 3D path planning is done in the three orthogonal two-dimensional projections of a 3D environment. Collision checking to increase the optimality for 3D paths is done in each of the three orthogonal two-dimensional subspaces.

Impact Of Automation On Process Control Decision-Making, Steven M. Miller, Susan R. Bereiter

Research Collection School Of Computing and Information Systems

This paper investigates changes in the process control of a vehicle assembly plant which had been modernized from a principally manual procedure to one that uses programmable automation extensively. Process control is defined as the information flow and decision-making required to perform basic process operations. We investigate the effects of implementing a computer-integrated production system on the amount and types of process control decision-making and on the distribution of process control decision-making between humans and machines. After automation, the emphasis on decisions regarding product quality specifications increased and the emphasis on decisions related to flexibility in handling a variety of …

Computers And Robotics, Wayne Tinga

Pro Rege

No abstract provided.

Impacts Of Robotics And Flexible Manufacturing Technologies On Manufacturing Costs And Employment, Steven M. Miller

Research Collection School Of Computing and Information Systems

The issues analyzed in this paper are the extent to which unit costs and production labor requirements might be reduced in manufacturing industries if there is more widespread use of industrial robots and flexible systems. The analysis is reported in detail in Miller (1983). These issues are analyzed from two different perspectives. The technological focus of the first perspective is narrowly confined to the use of robotic manipulators. It is assumed that robotic manipulators will be “retrofitted” into existing production facilities without making major changes in the organization of production within the factory, other than modifying individual work stations so …

Robotic Realities: Near Term Prospects And Problems, Robert U. Ayres, Steven M. Miller

Research Collection School Of Computing and Information Systems

Industrial robots are automation, but with a difference. Other machine tools are extensions of human capabilities, while robots are seen mainly as substitutes for human workers. Robots will find most of their industrial applications during the next decade or two in the metal-working sectors, where they will begin to displace semiskilled machine operatives in medium to large batch production operations. They cannot substitute for skilled machinists or other workers doing nonroutine jobs, or specialized, dedicated hard automation used in mass production. The current generation of robots, lacking sensory data processing and interpretation capabilities, can potentially replace up to 1.3 million …

Robotics And The Conservation Of Human Resources, Robert U. Ayres, Steven M. Miller

Research Collection School Of Computing and Information Systems

Due to rapid expansion in the field of robotics, policy issues have arisen in regard to developing human skills to deal with the new technology and to deal with the obsolescent human skills which are the inevitable result of this growth pattern. Industrialists, educators, union leaders, and government officials must work cooperatively to insure that the coming changes are made with minimum disruption. Improved training methods and courses have to be developed for the skills needed to control, manage and supervise the new machines. Some of the ways in which this can be accomplished are through offering financial incentives for …