Computer Engineering Commons^™

A Realization Of Sc-Cnn-Based Circuit Using Ftfn, Eni̇s Günay, Esma Uzunhi̇sarcikli, Recai̇ Kiliç, Mustafa Alçi

Turkish Journal of Electrical Engineering and Computer Sciences

In this paper, a realization of the State Controlled Cellular Neural Network (SC-CNN)-based circuit using Four Terminal Floating Nullor (FTFN) as active element is presented. In this realization, a new version of autonomous Chua's circuit has been considered using FTFN realization of SC-CNN-based circuit. The performance of the proposed SC-CNN-based circuit is demonstrated by PSpice simulations.

Prior Knowledge Input Method In Device Modeling, Serdar Heki̇mhan, Serdar Menekay, N. Serap Şengör

Turkish Journal of Electrical Engineering and Computer Sciences

The artificial neural networks are being used in modelling electronic elements and devices especially at microwave frequencies where non-linearity and dependence on frequency cannot be neglected. In this paper, instead of using artificial neural networks as a unique modelling device prior knowledge input method based on feed-forward artificial neural network structures as multi-layer perceptrons and wavelet-based neural networks is investigated. The benefits of prior knowledge input method over plain usage of artificial neural networks in modelling BJT is explored by comparing models obtained with and without prior knowledge input. The novelty of the paper is utilizing wavelet-based neural networks as …

Transformer Protection Using The Wavelet Transform, Okan Özgönenel, Güven Önbi̇lgi̇n, Çağri Kocaman

Turkish Journal of Electrical Engineering and Computer Sciences

This paper introduces a novel approach for power transformer protection algorithm. Power system signals such as current and voltage have traditionally been analysed by the Fast Fourier Transform. This paper aims to prove that the Wavelet Transform is a reliable and computationally efficient tool for distinguishing between the inrush currents and fault currents. The simulated results presented clearly show that the proposed technique for power transformer protection facilitates the accurate discrimination between magnetizing inrush and fault currents in transformer protection.

Multilayer Capacitor Model Of The Earth's Upper Crust, Berk Üstündağ, Özcan Kalenderli̇, Haluk Eyi̇doğan

Turkish Journal of Electrical Engineering and Computer Sciences

In this study, an equivalent electric circuit model of Earth's upper crust is proposed to explain the behavior of measurement patterns acquired from network of the earthquake forecast project. A multi-layer capacitor model having active components that couples with the monopolar probe close to the surface is used to determine earthquake precursory patterns due to structural changes in time. Equivalent circuit model was developed for a) dilatency process that is assumed to be a stress weakening reason and b) external force source that increases shear stress over the fault until sudden decrement before the earthquake. A data acquisition system consisting …

Turbo Codes: The Issue Of Average Union Upper Bound Under Imperfect Channel State Information In Rayleigh Fading Channels, Erhan A. İnce, Syed Amjad Ali

Turkish Journal of Electrical Engineering and Computer Sciences

The potential of turbo codes to demonstrate excellent performance in the region of low signal to noise ratio is now a familiar fact. The idea of turbo codes was first introduced by Berrou and was based on the clever utilization of the existing decoding mechanism of BCJR with a change in the encoder by introducing feedback and an interleaver in the overall scheme. Since then, these powerful forward error correcting codes have attained a significant attention and have either replaced or have become a sturdy candidate for many applications in this era of modern communication systems. So far, a lot …

Two-Variable Scattering Formulas To Describe Some Classes Of Lossles Two-Ports With Mixed, Lumped Elements And Commensurate Stubs, Ahmet Sertbaş

Turkish Journal of Electrical Engineering and Computer Sciences

Using the semi-analytic method based on the construction of two-variable scattering functions, which describe lossless two-ports with two kinds of elements, for some classes of ladder networks formed with lumped elements and commensurate stubs, the explicit descriptive formulas are produced up to six mixed-elements. To exhibit the efficiency of the explicit descriptive equations in the design of the broadband microwave circuits, a single matching design problem (UHF antenna matching) is solved by using the obtained two-variable scattering formulas.

Performance Analysis Of A Fuzzy Logic Based Rotor Resistance Estimator Of An Indirect Vector Controlled Induction Motor Drive, Y. Miloud, Azeddine Draou

Turkish Journal of Electrical Engineering and Computer Sciences

This paper presents a simple method for estimating rotor resistance in an indirect vector-controlled induction motor drive. This is important in vector control, if high-performance torque control is needed. For this purpose, a rotor resistance estimator using fuzzy logic technique is used and analysis, design, and digital simulations are carried out to demonstrate the effectiveness of the proposed estimator.

A Robustness Analysis Procedure For Realistic Missiles, Reşat Özgür Doruk, Erol Kocaoğlan

Turkish Journal of Electrical Engineering and Computer Sciences

This paper presents a robustness analysis procedure for short range realistic missile autopilots. The sensitivity of the autopilots to the aerodynamic parameter uncertainties is investigated through the structured singular value theory where the results are verified through nonlinear simulations. Different types of perturbations are implemented in order to measure the complete performance of the missile.

Implementation Of A New Self-Tuning Fuzzy Pid Controller On Plc, Onur Karasakal, Engi̇n Yeşi̇l, Müjde Güzelkaya, İbrahi̇m Eksi̇n

Turkish Journal of Electrical Engineering and Computer Sciences

In this study, the self-tuning method for fuzzy PID controllers that has been developed in a previous study of the authors is implemented on PLC in order to control some standard processes formed on FEEDBACK PCS 327 Process Control Simulator. In this tuning method, the input scaling factor corresponding to the derivative coefficient and the output scaling factor corresponding to the integral coefficient of the fuzzy PID controller are adjusted using a fuzzy inference mechanism with a new input called ``normalized acceleration''. The results of the implementation have been compared with those of the classical fuzzy PID controller without a …

A Survey On The H.264/Avc Standard, Nükhet Özbek, Turhan Tunali

Turkish Journal of Electrical Engineering and Computer Sciences

H.264/AVC is a recently completed video compression standard jointly developed by ITU-T VCEG and ISO/IEC MPEG standards committees. The standard is becoming more popular as it promises much higher compression than that possible with earlier standards. The standard provides flexibilities in coding and organization of data which enable efficient error resilience. The increased coding efficiency offers new application areas and business opportunities. As might be expected, the increases in compression efficiency and flexibility come at the expense of increase in complexity, which is a fact that must be overcome. This paper provides an overview of the technical features of H.264 …

Control Charts Approach For Scenario Recognition In Video Sequences, Ersi̇n Elbaşi, Long Zuo, Kishan Mehrotra, Chilukuri Mohan, Pramod Varshney

Turkish Journal of Electrical Engineering and Computer Sciences

A new approach, based on control charts, is presented for the task of recognition of events and scenarios in video image sequences. For each image in the sequence, low level image processing and feature extraction steps result in feature descriptors for objects of interest detected in the images. Control charts analysis is then explored to classify the nature of the activity depicted by the temporal changes in these features over the image sequence. Scenario recognition with higher accuracy is achieved using this simple approach.

A Model For User Profiling Systems With Interacting Agents, Sanem Sariel, Tevfi̇k Akgün

Turkish Journal of Electrical Engineering and Computer Sciences

Service systems according to users' personal demands and preferences are on their way to provide required services in many application domains. Emulation of interactive model of human societies produces valuable outcomes for such systems. In this work, a system model with interactive agents for multi user service systems is proposed. A novel social interactive agent model using different interaction forms is also included in this proposal. In this model, agents decide how to serve to their users by considering their users' profiles and information from other agents. User clusters are formed by clustering techniques. The Q-learning algorithm is used for …

A Content-Based Fuzzy Image Database Based On The Fuzzy Artmap Architecture, M. Uysal, Fatoş Tünay Yarman Vural

Turkish Journal of Electrical Engineering and Computer Sciences

A major design issue in content-based image retrieval system is the selection of the feature set. This study attacks the problem of finding a discriminative feature for each class, which is optimal in some sense. Fuzzy ARTMAP architecture is used to find this discriminative feature set. For this purpose, initially, a large variety of features are extracted from the regions of the pre-segmented images. Then, the feature set of each object class is learned using the Fuzzy Art Map Architecture, by identifying the weights of each feature for each object class. In the querying phase, trained set of feature weights …

Color Image Profiling Using Fuzzy Sets, Amine Ait Younes, Isis Truck, Herman Akdag

Turkish Journal of Electrical Engineering and Computer Sciences

In this article, a software for image indexing and retrieval is presented. The classification proposed here is based on the dominant color(s) of the images. The process consists in assigning a colorimetric profile to the image in HLS space (Hue, Lightness, Saturation). First, the definition of hue is done thanks to a fuzzy representation to take into account the non-uniformity of colors distribution. And then, lightness and saturation are represented through linguistic qualifiers also defined in a fuzzy way. Finally, the profile is built through fuzzy functions representing the membership degree of the image to different classes. In order to …

Gain-Bandwidth Product Optimization Of Heterostructure Avalanche Photodiodes, Oh-Hyun Kwon, Majeed M. Hayat, Joe C. Campbell, Bahaa E.A. Saleh, Malvin Carl Teich

Electrical and Computer Engineering Faculty Research and Publications

A generalized history-dependent recurrence theory for the time-response analysis is derived for avalanche photodiodes with multilayer, heterojunction multiplication regions. The heterojunction multiplication region considered consists of two layers: a high-bandgap Al/sub 0.6/Ga/sub 0.4/As energy-buildup layer, which serves to heat up the primary electrons, and a GaAs layer, which serves as the primary avalanching layer. The model is used to optimize the gain-bandwidth product (GBP) by appropriate selection of the width of the energy-buildup layer for a given width of the avalanching layer. The enhanced GBP is a direct consequence of the heating of primary electrons in the energy-buildup layer, which …

The Effect Of Time Delays On The Stability Of Load Balancing Algorithms For Parallel Computations, John Chiasson, Zhong Tang, Jean Ghanem, Chaouki T. Abdallah, J. Douglas Birdwell, Majeed M. Hayat, Henry Jérez

Electrical and Computer Engineering Faculty Research and Publications

A deterministic dynamic nonlinear time-delay system is developed to model load balancing in a cluster of computer nodes used for parallel computations. The model is shown to be self consistent in that the queue lengths cannot go negative and the total number of tasks in all the queues and the network are conserved (i.e., load balancing can neither create nor lose tasks). Further, it is shown that using the proposed load balancing algorithms, the system is stable in the sense of Lyapunov. Experimental results are presented and compared with the predicted results from the analytical model. In particular, simulations of …

Exponential Time Response In Analogue And Geiger Mode Avalanche Photodiodes, C. Groves, C. H. Tan, J. P.R. David, G. J. Rees, Majeed M. Hayat

Electrical and Computer Engineering Faculty Research and Publications

The mean avalanche current impulse response in an avalanche photodiode exhibits an initial transient and then grows or decays, above or below breakdown, at exponential rates which depend only on the probability distributions of the electron and hole ionization events. The process continues while the electric field profile remains unchanged by the applied bias or the evolving space charge. Below breakdown the distribution in the avalanche duration also exhibits an initial transient and then decays exponentially at the same rate as the mean current. Below breakdown the standard deviation in current decays exponentially at one half of the rate of …

Information-Theoretic Criterion For The Performance Of Single-Photon Avalanche Photodiodes, David A. Ramirez, Majeed M. Hayat, Sergio N. Torres, Bahaa E.A. Saleh, Malvin Carl Teich

Electrical and Computer Engineering Faculty Research and Publications

A channel-capacity metric is introduced for assessing the performance of single-photon avalanche photodiodes (SPADs) when used as detectors in laser communication systems. This metric is employed to theoretically optimize, with respect to the device structure and operating voltage, the performance of SPADs with simple InP or In/sub 0.52/Al/sub 0.48/As-InP heterojunction multiplication regions. As the multiplication-region width increases, an increase is predicted in both the peak and the full-width at half-maximum of the channel capacity curve versus the normalized excess voltage. Calculations also show the existence of an optimal In/sub 0.52/Al/sub 0.48/As-InP heterojunction multiplication region that maximizes the peak channel capacity …

Theoretical Investigation Of Quantum-Dot Avalanche Photodiodes For Mid-Infrared Applications, Sanjay Krishna, Oh-Hyun Kwon, Majeed M. Hayat

Electrical and Computer Engineering Faculty Research and Publications

A novel midinfrared sensor, called the quantum-dot avalanche photodiode (QDAP), is proposed which is expected to have improved signal-to-noise ratio (SNR) in the presence of Johnson noise over its quantum-dot (QD) counterpart. In the QDAP, an intersubband QD detector is coupled with a thin, low-noise GaAs avalanche layer through a tunnel barrier. The avalanche layer provides the necessary photocurrent gain required to overcome Johnson noise and nearly achieve the dark-current-limited SNR of the QD detector. In the proposed three-terminal device, the applied biases of the QD-detector and the avalanche-photodiode sections of the QDAP are controlled separately. This feature permits the …

The Effects Of Influent Debit On Hydrodynamic Characteristic Of Bojongsoang Facultative Pond: Without Wind Effects, Rositayanti Hadisoebroto, Suprihanto Notodarmojo

Makara Journal of Technology

The Effects of Influent Debit on Hydrodynamic Characteristic of Bojongsoang Facultative Pond: Without Wind Effects. The performance of facultative pond in Bojongsoang WWTP have reported to be unstable. One of the cause of the unstable performance is the hydrodynamic characteristics that not met the criterion. The improper hydrodynamic characteristics are included the existence of dead-zone, the short-circuiting, and the turbulence due to eddy current. The study was to analyze the effect of the influent debit variation on the hydrodynamic characteristics of the pond using mathematical model. The two-dimensional hydrodynamic model was built from two hydrodynamic equations which are continuity and …

Fuel Injection System For One Cylinder Motor Cycle Engine, Bambang Sugiarto

Makara Journal of Technology

Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel …

Influence Of Connection Placement To The Behavior Of Precast Concrete Exterior Beam-Column Joint, Elly Tjahjono, Heru Purnomo

Makara Journal of Technology

Influence of Connection Placement to the Behavior of Precast Concrete Exterior Beam-Column Joint. This paper presents an experimental study on the influence of connection placement to the behaviour of exterior beamcolumn joint of precast concrete structure under semi cyclic loading. Four half-scale beam-column specimens were investigated. Three beam-columns were jointed through connection that are placed in beam-column joint region and the forth is connected at the plastic hinge potensial region of the beam. Crack patterns, strength, stiffness and ductility of the test specimens have been evaluated. The test result indicated that all beam-column specimens show good ductility behavior.

Modelling And Simulation Of Packed Bed Catalytic Converter For Oxidation Of Soot In Diesel Powered Vehicles Flue Gas, Mohammad Nasikin, Praswasti P.D.K. Wulan, Vita Andrianty

Makara Journal of Technology

Modelling and Simulation of Packed Bed Catalytic Converter for Oxidation of Soot in Diesel Powered Vehicles Flue Gas. Diesel vehicle is used in Indonesia in very big number. This vehicle exhausts pollutants especially diesel soot that can be reduces by using a catalytic converter to convert the soot to CO2. To obtain the optimal dimension of catalytic converter it is needed a model that can represent the profile of soot weight, temperature and pressure along the catalytic converter. In this study, a model is developed for packed bed catalytic converter in an adiabatic condition based on a kinetic study that …

Optic Properties On Aggase2 Polycristal Fabrication, A. Harsono Soepardjo, I Dewa Made Janusetiawan

Makara Journal of Technology

Optic Properties on AgGaSe2 Polycristal Fabrication. Polycristal AgGaSe2, is compound (I-III-VI2) a semiconductor as basic material for thin film for solar cell. Polycristal was succesfully grown using Bridgmann Method, heated on sequential temperature treatment until 850°C and cooled down slowly until room temperature. Results observed were in the form of ingot (bars) with more or less 3 cm length and 13 mm in diameter. By using X-Ray Fefraction, composition obtained of each element (weight %) was Ag = 29,3996 %, Ga = 36,8123 % and Se = 30,29 % while using X-Ray Difraction lattice parameter obtained/calculated a = 4,4112 Å, …

Condition Monitoring Of Squirrel-Cage Induction Motors Fed By Pwm-Based Drives Using A Parameter Estimation Approach, Behrooz Mirafzal, F. Fateh, Chia-Chou Yeh, Richard J. Povinelli, Nabeel Demerdash

Electrical and Computer Engineering Faculty Research and Publications

Abstract:

A rotor condition monitoring technique is presented in this paper based on a parameter estimation approach. In this technique, the stator currents, voltages and motor speed are used as the input signals, where the outputs will be the rotor's inductance, resistance and consequently rotor time constant. This approach is verified by simulation of two different induction motor cases. These simulations are buttressed by experimental data obtained for a 2-hp induction motor in the case of healthy as well as one, three and five rotor bar breakages. In these tests, the induction motor was energized from a PWM-based drive, in …

Thermodynamic Modeling, Energy Equipartition, And Nonconservation Of Entropy For Discrete-Time Dynamical Systems, Wassim H. Haddad, Qing Hui, Sergey G. Nersesov, Vijaysekhar Chellaboina

Department of Electrical and Computer Engineering: Faculty Publications

We develop thermodynamic models for discrete-time large-scale dynamical systems. Specifically, using compartmental dynamical system theory, we develop energy flowmodels possessing energy conservation, energy equipartition, temperature equipartition, and entropy nonconservation principles for discrete-time, large-scale dynamical systems. Furthermore, we introduce a new and dual notion to entropy; namely, ectropy, as a measure of the tendency of a dynamical system to do useful work and grow more organized, and show that conservation of energy in an isolated thermodynamic system necessarily leads to nonconservation of ectropy and entropy. In addition, using the system ectropy as a Lyapunov function candidate, we show that our discrete-time, …

Hierarchical Hybrid Multicast An End System Multicast Algorithm Approach, Guillermo Loaisiga

Electrical & Computer Engineering Theses & Dissertations

Due to the rapid development in the computer and communication technologies, the Internet is experiencing an increasing demand of high-speed, real-time distributed applications, such as live streaming multimedia, videoconferencing, distributed simulations, and multiparty games. Multicast is an efficient transmission mechanism to support these applications. Historically, IP Multicast (IPM) has provided multicast support with well-known benefits, especially in bandwidth savings. However, it has experienced little deployment due to economic and architectural limitations.

Overlay multicast holds promise for the implementation of large scale Internet multicast services. An overlay network is a virtual topology constructed on top of the Internet infrastructure. This concept …

Huffman Approach To Opcode Compression, Jason B. Shreve

Electrical & Computer Engineering Theses & Dissertations

Instructions are the building blocks of computer programs. They are composed of opcodes, which uniquely identify each instruction, and the operands or data. In most architectures, the instruction length is a set multiple of the word size. The size and number of operands vary by instruction. Due to programmer usage, program need, or compiler design, opcodes do not occur with a constant distribution. Likely, some opcodes occur very frequently, whereas others occur very infrequently or not at all. If the length of an opcode were representative of its frequency, compression in program size might be achieved.

This thesis is an …

Micro-Switches With Sputtered Au, Aupd, Au-On-Aupt, And Auptcu Alloy Electric Contacts, Ronald A. Coutu Jr., P. E. Kladitis, R. Cortez, R. E. Strawser, Robert L. Crane

Electrical and Computer Engineering Faculty Research and Publications

This work is the first to report on a new analytic model for predicting micro-contact resistance and the design, fabrication, and testing of microelectromechanical systems (MEMS) metal contact switches with sputtered bi-metallic (i.e. gold (Au)-on-Au-platinum (Pt), (Au-on-Au-(6%)Pt)), binary alloy (i.e. Au-palladium (Pd), (Au-(2%)Pd)), and tertiary alloy (i.e. Au-Pt-copper (Cu), (Au-(5%)Pt-(0.5%)Cu)) electric contacts. The micro-switches with bi-metallic and binary alloy contacts resulted in contact resistance between 1-2 /spl Omega/ and, when compared to micro-switches with sputtered Au electric contacts, exhibited a 3.3 and 2.6 times increase in switching lifetime, respectively. The tertiary alloy exhibited a 6.5 times increase in switch lifetime …

A Comparison Of Micro-Switch Analytic, Finite Element, And Experimental Results, Ronald A. Coutu Jr., P. E. Kladitis, Lavern A. Starman, J. R. Reid

Electrical and Computer Engineering Faculty Research and Publications

Electrostatically actuated, metal contact, micro-switches depend on having adequate contact force to achieve desired, low contact resistance. In this study, higher contact forces resulted from overdriving cantilever beam style switches, after pull-in or initial contact, until the beam collapsed onto the drive or actuation electrode. The difference between initial contact and beam collapse was defined as the useful contact force range. Micro-switch pull-in voltage, collapse voltage, and contact force predictions, modeled analytically and with the CoventorWare finite element software package, were compared to experimental results. Contact resistance was modeled analytically using Maxwellian spreading resistance theory. Contact resistance and contact …