Transportation Engineering Commons^™

Inspection And Evaluation Of Load‐Bearing Capacity Of Hollow‐Box Arch Bridge, Song Zegang, Yang Min

Journal of China & Foreign Highway

The inspection and evaluation of the load-bearing capacity of in-service bridges are crucial for ensuring structural and operational safety. This paper investigates a 90 m span hollow-box arch bridge, assessing its damage condition, material properties, and state parameters to determine partial evaluation coefficients. The bridge’s ultimate limit state and serviceability limit state load-bearing capacities of the main arch ring were then evaluated using both the original design standards and the current code. The results show that, compared to the original design standards, the safety factor for the compressive load-bearing capacity of the main arch ring cross-section is significantly reduced when …

Model Test Study On Mechanical Characteristics Of Spherical Joints In Multi‐Point Support Swivel System, Zeng Lifei

Journal of China & Foreign Highway

As a critical load-bearing component in bridge swivel systems, the mechanical behavior of spherical joints is essential for the safety of bridge swiveling operations. This study focuses on the spherical joints of a multi-point support swivel system for the bridge over the Xiangyang North Marshalling Yard. Model tests were conducted to analyze the effects of the number of supporting legs, swivel speed, track smoothness, and wind load on the stress of spherical joints. The stress variation patterns of spherical joints under different working conditions were investigated. The results show that increasing the number of supporting legs improves the uniformity of …

Analysis On Vehicle‐Bridge Interaction Of High‐Pier Continuous Rigid Frame Bridge, Liu Huaquan, Yang Dehai, Cai Chengqi, Huang Zhenming, Chen Zhouqi

Journal of China & Foreign Highway

To study the dynamic response characteristics of the vehicle-bridge system under moving vehicle loads, a three-span high-pier continuous rigid frame bridge was selected as the research object. A 2-axle, 7-degree-of-freedom vehicle model was applied to explore the effects of vehicle speed, number of vehicles, and vehicle load on the dynamic response of the vehicle-bridge system. The results show that vehicle speed has minimal impact on the peak displacement response of the bridge. However, when vehicles travel at the same speed, the peak displacement response differs across bridge spans, with resonance occurring at a vehicle speed of 40 km/h. As the …

Analysis And Reinforcement Measures For Unconventional Cracks In Gravity U‐Type Abutment, Cheng Kun, Du Yinguang, Liu Zhang

Journal of China & Foreign Highway

Horizontal cracking at the foundation level is uncommon in gravity U-type abutments. This paper investigates the causes and reinforcement measures for unconventional horizontal cracks in the foundation and vertical cracks in the abutment wall of a gravity U-type abutment on a highway bridge. Survey and analysis results show that the vertical cracks in the abutment wall are structural cracks caused by excessive reaction forces from permanent loads combined with the impact loads from vehicles at expansion joints. The horizontal foundation cracks result from the presence of filler interlayers at the foundation, which softened over time due to water exposure, leading …

Research On Application Of Equivalent Stiffened Plate Elements In Local Stability Calculation Of U‐Shaped Stiffened Plates, Chen Xiangjun

Journal of China & Foreign Highway

To address the issue of excessively large computational models in the numerical simulation of U-shaped stiffened plates in large-span flat steel box girder main girders, this paper proposes a finite element calculation theory using equivalent stiffened plate elements and a simplified method for U-shaped stiffened plates. By simplifying the U-shaped small box ribs in U-shaped stiffened plates into equivalent stiffening strips, the transverse stiffness of the cover plate is redistributed, and the effect of equivalent stiffeners on the stress of the plates is calculated. Stability analysis was conducted using Fortran language developed on the Ansys platform, and the results were …

Study On Supporting Effect Of Pre‐Stressed Rock Bolts On Tunnel Face, Shen Xiangqian, Chen Daoyun, Zheng Chao

Journal of China & Foreign Highway

Focusing on the stability issues of the tunnel face in the large deformation section of soft rock in the Muzhailing Tunnel on the Weiyuan-Wudu Expressway, this paper proposes a technical solution for temporary reinforcement of the tunnel face using pre-stressed rock bolts. Numerical simulations were conducted to evaluate the reinforcement effect and effective range of pre-stressed rock bolts on the tunnel face, and the influence of initial ground stress on the reinforcement effect was further analyzed. The results show that under the given engineering conditions, pre-stressed rock bolts demonstrate significantly better reinforcement effects on the tunnel face compared to fully …

Optimization Research Of Laying Method And Material Type Selection Of Thermal Insulation Layer For Tunnels In Cold Region, Wu Tao, Liu Zhichun, Liu Xuejiao, Zhang Hongfei

Journal of China & Foreign Highway

To address the issue of frost damage in tunnels in cold regions, research on thermal insulation and frost prevention is crucial. This paper utilizes an improved analytic hierarchy process combined with grey relational analysis to identify optimal insulation materials suitable for different laying methods that provide effective insulation. Numerical simulation methods were then used to calculate and analyze the tunnel temperature field under various combinations of insulation materials and laying methods. Based on the “composite temperature field” comparison results, the optimal insulation scheme was determined. The results show that the “off-wall laying + Furritek insulation board” combination is the optimal …

Research On Gas Migration And Ventilation Disaster Prevention In Highway Tunnel, Wang Zhongqi, Lin Zhi, Feng Sen, Yang Hongyun, Chen Xiang, Liu Jiang

Journal of China & Foreign Highway

To understand the gas migration patterns and ventilation disaster prevention techniques during tunnel construction, this paper uses a real tunnel as the engineering context. A 3D transient ventilation physical model was established using Ansys Fluent, and the effects of ventilation on gas concentration were analyzed in combination with on-site monitoring data. The results show that the uneven diffusion of gas and airflow is prominent. Gas concentration and wind speed stabilize at a distance of 120 m from the tunnel face as ventilation time increases. During gas monitoring and prevention, special attention should be paid to the area between the tunnel …

Study On Health State Evaluation Method Of Highway Tunnel Based On Neutrosophic Theory, Deng Fayou, Xia Caichu, Xu Chongbang

Journal of China & Foreign Highway

The structural complexity and inherent uncertainties of highway tunnels necessitate comprehensive consideration of various uncertain factors to reasonably evaluate their health state. By introducing neutrosophic theory, which accounts for structural uncertainties, this paper proposes a health state evaluation method for highway tunnels based on neutrosophic cosine and tangent similarity measures. The proposed method was applied to evaluate the health state of 10 samples. A comparison between the actual evaluation grades and the results obtained using the proposed method shows that the evaluation results are consistent with the actual grades. This indicates that the proposed method effectively addresses uncertainties in the …

Interlayer Bonding Performance Of Wtr/Apao Composite Modified Asphalt, Ji Hongyan, Yan Kezhen, Yuan Jian, Zhang Xuanyu

Journal of China & Foreign Highway

To investigate the bonding performance of waste tire rubber (WTR)/ amorphous α-olefin copolymer (APAO) composite modified asphalt as a waterproof bonding layer in asphalt pavements on cement concrete bridges, shear and pull-off tests were conducted. The shear strength and pull-off strength of SBS-modified asphalt, WTR-modified asphalt, and WTR/APAO composite modified asphalt were compared under different application rates and temperatures. The results show that WTR/APAO composite modified asphalt exhibits the best bonding performance, followed by WTR-modified asphalt, with SBS-modified asphalt performing the worst. Based on the shear and pull-off strengths at different temperatures, the optimal application rates were determined as 1.7 …

Study On Modification Of Phosphate Pretreated Aggregate Vegetation Porous Concrete, Li Zhengxing, Hou Zebiao

Journal of China & Foreign Highway

To enhance the interfacial structure between aggregates and cementitious materials in vegetation porous concrete and improve its compressive strength, this paper investigates the effects of phosphate pretreatment on aggregate properties and the corresponding compressive strength of vegetation porous concrete. The performance of untreated aggregates, water-washed aggregates, and acid-treated aggregates was evaluated, and the modification mechanism was explored from the perspective of the interfacial transition zone (ITZ) using scanning electron microscopy (SEM). The results show that phosphate effectively removes impurities from the aggregate surface and increases surface roughness, thus improving the compactness and stability of the ITZ. After soaking the aggregates …

Optimization Study On Indoor Vibratory Compaction Curves Of Cement Stabilized Macadam, Qiu Youqiang, Zhang Liujun

Journal of China & Foreign Highway

To obtain well-defined secondary convex vibratory compaction curves and reduce the need for supplemental compaction point tests, this paper uses vibratory compaction tests for cement stabilized macadam in laboratory settings. Tests were conducted for two pavement sections along National Highway 110 (Hohhot to Bikeqi), exploring the influence of predefined moisture content intervals on vibratory compaction curves under varying cement dosages. The vibratory compaction curves were also compared with heavy compaction curves for analysis. The results show that the vibratory compaction curve is significantly influenced by the predefined moisture content intervals and cement dosage. For a moisture content interval of 1%, …

Selection Of Phase Change Materials For Asphalt Pavement Based On Molecular Dynamics Simulation, Liu Fujun, Tian Xin, Liang Meichen, Guo Meng

Journal of China & Foreign Highway

Phase change materials (PCMs) have significant application potential in temperature regulation for asphalt pavements. To select suitable PCMs for road applications, this paper utilizes molecular dynamics simulation to analyze the molecular behaviors of lauric acid and polyethylene glycol (PEG). Experimental studies were conducted to validate the simulation results. The results show that molecular dynamics simulation provides an efficient and convenient method for comparing the performance of PCMs. PEG outperforms lauric acid in terms of molecular density, cohesive energy density, solubility parameters, and thermal conductivity, making it more suitable as a phase change material for asphalt pavements.

Experimental Study On Water Stability Of Sand Compound Modified Mud Road, Chai Ruixiang, Wu Kai, Ye Wei, Cui Jinmei, Wang Jicheng, Li Zhantao

Journal of China & Foreign Highway

Sand compound modified mud, as a coupled medium of sand and soil, differs from traditional modified mud. To further investigate its water stability indicators, orthogonal design was employed to conduct indoor water stability simulation tests (surface infiltration test, underground capillary water test, and dry-wet cycle test) on sand compound modified mud. The water stability of the modified mud was characterized using the change rate of unconfined compressive strength (UCS). The results show that the unconfined compressive strength and water stability of the modified mud were significantly improved. Under different water disturbance conditions, the order of influence of factors such as …

Experimental Study On Influence Of Phosphorus Slag Powder On Pervious Concrete, Lou Jianxin, Yang Jianyong, Zhang Yuxian, Li Jun, Wang Jie, Liu Jian

Journal of China & Foreign Highway

This paper investigates the effects of replacing cement with phosphorus slag powder on the mechanical properties, permeability, and pavement performance of pervious concrete. The results show that incorporating a certain amount of phosphorus slag powder as a partial replacement for cement in pervious concrete is feasible. When the replacement ratio of phosphorus slag powder is within 10%, it enhances the strength of pervious concrete. The optimal replacement ratio of phosphorus slag powder is 8%, achieving a compressive strength of 24.18 MPa, a void ratio of 15.37%, and a permeability coefficient of 2.45 mm/s, which meet the requirements for fully permeable …

Study On Alkali Excitation Mechanism Of Large Dosage Slag Fine Powder, Mei Yang

Journal of China & Foreign Highway

To reveal the alkali excitation mechanism of high-dosage slag, this paper combines a three-factor, three-level orthogonal design with macro- and micro-performance tests and microstructure analysis. The effects of different activators, including Ca(OH)2, Na2SiO3, Na2SO4, and CaSO4, in single and dual combinations on the initial and final setting times, pore solution pH, and strength of concrete were explored. The results show that the impact on the strength of hardened paste of composite cementitious materials is ranked as: activator type > dosage > dual-mix ratio. The optimal dual-mix dosage is 4%, with the best combination being Ca(OH)2 and Na2SiO3 at a ratio of 5:1. …

Dynamic Load Response Analysis Of Rubber Powder Modified Asphalt Mixture, Yang Sanqiang, Sun Shuang, Li Qian, Liu Xinlei, Qin Lusheng

Journal of China & Foreign Highway

To investigate the mechanical response of rubber powder modified asphalt pavement under dynamic loads, this paper, based on the “Full-Scale Accelerated Pavement Loading Testing” project, designed experimental schemes for asphalt mixtures with varying rubber powder contents. The paper employed accelerated loading test equipment to evaluate the stress and deformation of pavement structures, obtaining dynamic strain response data to analyze the strain response patterns of various structural layers. Combining finite element numerical simulations and a custom loading program, the paper examined the dynamic responses of rubber powder modified asphalt pavements under variable temperature conditions. The results show that through microscopic testing, …

Aging Asphalt Concrete Cracking Performance Under Different Cyclic Loading Frequencies, Yan Jingchen, Ma Yanpei, Yan Junjie

Journal of China & Foreign Highway

Using digital speckle technology, this paper examines the crack propagation behavior of asphalt concrete under repeated loading, analyzing the crack propagation mechanism from macro- and micro-perspectives under different aging conditions and loading frequencies for four types of asphalt concrete. The results show that the basalt fiber-reinforced asphalt concrete beam specimens delay the onset of the unstable crack propagation phase, thus extending the service life of the asphalt concrete. Aging accelerates the progression of asphalt concrete to the unstable crack propagation point, advancing this stage by 4%-5%. Under repeated loading frequencies of 5 Hz, 10 Hz, and 15 Hz, the damage …

Study On Microstructure Of Asphalt Modified By Oil‐Coal Blend, Guo Pengfei, Zhou Xinfeng

Journal of China & Foreign Highway

To investigate the microstructure and modification mechanism of asphalt modified with oil-coal blend, SK-90# asphalt was mixed with 5%, 10%, 15%, 20%, and 25% (external blending method) oil-coal blend to produce modified asphalt. The performance and microstructural changes of the modified asphalt were analyzed using contact angle testing, infrared spectroscopy, cross-sectional SEM, and X-ray photoelectron spectroscopy. The results show that the oil-coal blend exhibits good compatibility with asphalt. During the modification process, esterification reactions occurred, resulting in a decrease in hydroxyl-containing aromatic compounds and an increase in carbonyl-containing aromatic compounds. Macroscopically, the oil-coal blend-modified asphalt demonstrated excellent high-temperature performance.

Design And Development Of Two And Three Dimensional Integration System For Highway Based On Webgis, Che Defu, Zhou Huajun

Journal of China & Foreign Highway

To address the inefficiencies, lengthy cycles, and high resource demands in the process of determining the annual project database for highway maintenance quotas in Liaoning Province, a 2D and 3D integration system for highways based on WebGIS was designed and developed. This system not only provides a macroscopic view of the geographic distribution and overall characteristics of highways but also offers a detailed and intuitive representation of the spatial relationships and conditions of roadbeds and pavement damage. The system meets the needs of modern highway management and can serve as a reference for other highway maintenance quota tasks.

Research On Influence Factors And Efficiency Analysis Of Expressway Maintenance Marketization, Zhong Wen, He Shoukui, Wang Xiaodong

Journal of China & Foreign Highway

To promote market-oriented reform of highway maintenance, this paper investigates its influencing factors and outcomes and proposes an evaluation model for assessing its effects. A panoramic analysis method within a three-dimensional framework was employed to determine the evaluation content. Drawing on the balanced scorecard concept, the analysis incorporates four dimensions: business, user, internal management, and learning and growth, with the innovative addition of a social responsibility dimension to construct an evaluation indicator system. Subsequently, a cloud-based extension model was developed to evaluate the effectiveness of expressway maintenance marketization and calculate the evaluation grade. Empirical analysis was conducted using data from …

Analysis Of Expressway Routine Maintenance Performance Management Based On Dea, Li Yuhuan, Shi Xiaoli, Gao Nan

Journal of China & Foreign Highway

To allocate maintenance resources efficiently and improve management levels, this paper examines the maintenance performance and improvement strategies of routine maintenance projects for 23 expressways in Shaanxi Province using 2018 operational maintenance data and data envelopment analysis. The results show that for some inefficient subsidiaries, traditional radial- and slack-based performance improvement methods are challenging and impractical in the short term. Therefore, a scenario-dependent model-based long-term incremental improvement strategy is proposed. By leveraging relative improvement values, this strategy enables phased improvements for inefficient subsidiaries. It provides a feasible approach for subsidiaries to set lower short-term performance improvement targets while achieving gradual …

Study On The Minimum Radius Of Vertical Curve Of Highway Main Line Entrance Section Based On Merging Sight Distance, Li Yang, Zhao Yemei, Chen Tianxing

Journal of China & Foreign Highway

Given the limited research on the vertical curve radius of highway mainline entrance sections and the lack of differentiation between entrance and exit sections in existing studies, this paper identifies merging sight distance as the primary influencing factor for the vertical curve radius of entrance sections. Using merging sight distance as the control condition, the vertical curve radius of entrance sections was studied. A safety merging sight distance calculation model for highway mainline entrance sections was established by analyzing the traffic behavior characteristics of vehicles on the entrance mainline and considering drivers’ psychological and physiological characteristics. The sight distance model …

Safety And Operational Assessment Of Rural Free Right-Turn Ramp Intersections, Jonathon Camenzind

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Free right-turn (FRT) ramps are alternative right-turn lane designs for intersecting highways. As of 2023, 79 FRT ramps exist at 68 rural highway intersections in Nebraska. FRT ramps may be located on three-legged or four-legged intersections and may be on the minor, the major, or both minor and major approaches of the same intersection.

This research compared the 68 rural FRT intersections to 24 similar non-FRT rural intersections to identify differences in crash frequency and crash rate and tested for statistical significance using a two-sample t-test. Crash data were obtained for the ten- year period of 2010-2019, with a focus …

Historic Downtown Streetscape Plan Price City, Utah, Patricia Beckert

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

The idea of a small-town Main Street has profound meaning within the American culture that has prevailed for the past two centuries. Historically, Main Street serves as the beating heart of a community, a place where economic, social, cultural, and civic activities are centered (Francaviglia, 1996; Main Street America, n.d.). Since the beginning of the 19th century, many factors have led to the decline of Main Streets, and despite a variety of efforts from different stakeholders, that decline has only intensified in recent decades (Isenberg, 2008; Orvell, 2014 Howard, 2015). In 1980, after a three-year project conducted by the National …

Evaluation Of The Effect Of Mls Density Level Data On Dem, Essam Ghanem, Mostafa Rabah, Fekry Ashraf

Mansoura Engineering Journal

Mobile laser scanning (MLS) systems are quickly establishing themselves as the primary source of high-quality digital elevation models (DEM). Data density is the key element that determine the quality of DEMs. Moreover, point density acts a vital role in MLS operation planning and MLS project's cost. This study's goal was to evaluate the impact of point density from MLS on creating DEMs and the accuracy of computed volume in different interpolation methods. The finding demonstrated that the DEM's quality and the volume are more impacted by density level and interpolation method. Interpolation methods are affected by point density. There is …

Feasibility Study For A Continuous Mansfield Hollow State Park Multi-Use Path, Owen P. Spangler

Honors Scholar Theses

This report aims to design a pedestrian river crossing that connects the north and south ends of Mansfield Hollow State Park, utilizing both a new paved pathway and bridge construction. This report first uses GIS data to complete a feasibility study on pathway routing and cost. A preliminary route was selected based on grading and cost analysis. The requirements for constructing a multi-use pathway in the State of Connecticut were then explored, attempting to find a best-fit pathway alignment to accomplish that goal. Through a lengthy literature review, it was found that the pathway design would have to deviate from …

Analysis On Influence Factors Of Swelling Deformation Of Gravel Pile In Soft Soil Area Based On Orthogonal Numerical Test, Fan Liujun, Lu Xiaoming, Miao Peng

Journal of China & Foreign Highway

The gravel pile composite foundation is usually accompanied by swelling deformation when vertical settlement deformation occurs. The research on the swelling deformation characteristics and influencing factors of gravel pile composite foundations is of great importance for analyzing the settlement rule and deformation mechanism of gravel pile composite foundations. Based on an orthogonal numerical test, this paper used the finite element software Midas GTS to analyze the main influencing factors of the swelling deformation of the gravel pile and used range and variance analysis to analyze the sensitivity and significance of each influencing factor. Finally, through regression analysis, the optimized swelling …

Study On Ultimate Bearing Capacity Characteristics Of Overlying Shell Foundation, Bian Guirong, Li Fuyou, Qian Xiaotong, Xie Ke

Journal of China & Foreign Highway

For the calculation of the ultimate bearing capacity of the overlying hard crust foundation, based on the theory of Meerhoff and Hanna’s impact and shear failure, the sealing effect and stress diffusion effect of the overlying hard crust foundation were considered, and the formula for calculating the ultimate bearing capacity of the overlying hard crust double-layer foundation was derived and verified by an actual engineering example. The maximum error between the measured value and the calculated value of Hansen’s weighted average method, diffusion angle method, and Meerhoff and Hanna’s method was 74.2%, 31.5%, and 15.2% respectively, while the error was …

Analysis On Pavement Early Damage Characteristics And Influence Factors Of Baiyin Section Of National Highway 109, Shi Fuzhou, Han Fei, Tang Dandan, Liu Wuwen, Zhang Jinyuan

Journal of China & Foreign Highway

In order to explore the cause of early damage of highway asphalt pavement in Baiyin area of Gansu Province, this paper analyzed the main factors that affected the performance of asphalt pavement and investigated the use of asphalt pavement in this area, climate environment, and traffic conditions. By taking Baiyin section of National Highway 109 as an example, the specific data were deeply analyzed. Based on the investigation of pavement use, the situation and decay rule of local asphalt pavement were summarized. According to the investigation of the climate environment, the influence of solar radiation, temperature difference, and other conditions …