Transportation Engineering Commons^™

Study On Dynamic Allocation Optimization Of Highway Pavement Maintenance Funds, Zou Yi

Journal of China & Foreign Highway

The conflict between the lack of maintenance funds and the growth of maintenance demand restricts the improvement of highway pavement technologies. In this paper, the state space of pavement maintenance demand was defined by the technical condition of the pavement, and the state of demand under different maintenance measures was designed as a Markov decision process. The dynamic allocation optimization model of highway pavement maintenance funds was established, and the corresponding genetic algorithm was designed. Finally, an example was given to simulate the optimized model. The results show that the Markov decision process can dynamically allocate highway pavement maintenance funds, …

Influence Factors Of Deicing And Thaw Performance Of Asphalt Mixture With Low Freezing Point, Zhou Shuiwen, Lin Fang, Zhang Xiaohua, Zhang Lingbo, Jiang Haoqiu

Journal of China & Foreign Highway

The conductivity test was used to study the release law of thawing and deicing components. The freezing test was used to study the cooling law of the mixture, and the thawing rate test was used to study the thawing and deicing performance. The results show that the release of thawing and deicing components of materials with a low freezing point is temperature-dependent, and the release at the high temperature is 3.49–3.77 times that at the low temperature. The granular materials tend to dissolve in water, which results in the release rate of thawing and deicing components faster than that of …

Experimental Analysis On Recycling And Mechanical Properties Of Waste Cement, Chen Liang

Journal of China & Foreign Highway

In order to recycle waste cement, construction waste cement materials were collected in the laboratory, and they were crushed, ground, and heat treated to facilitate reuse. Then, the waste cement was combined with the commonly used active fly ash admixture to prepare a new cement material for test analysis. The results show that the new cement material produced by industrial by-product, fly ash and waste cement material is feasible. A small amount of construction waste cement material (about 5%) can increase the 28-day compressive strength of cement by more than 50%, and the compressive strength of the prepared building material …

Experimental Study On Characteristics And Stability Of Different Aged Steel Slag Aggregate, Zhang Hongri, Wang Guiyao, Feng Jian, Lan Tianzhu, Wu Tao

Journal of China & Foreign Highway

Steel slag aggregate has good building material properties, but the utilization rate of steel slag in road engineering is low at present. In this paper, the chemical composition, basic physical and mechanical indexes, f⁃CaO, f⁃MgO, pulverization rate, CRB expansion rate, and other indexes of open-air aged steel slag aggregate in Fangchenggang, Guangxi Province for 0, 6, and 12 months were studied. The results show that the physical and mechanical properties of steel slag aggregate basically meet the requirements of road base materials and subgrade fillers, but the indexes of f⁃CaO, pulverization rate, and CRB expansion rate of steel slag aggregate …

Study On Effect Of Fiber Stabilizers On Water Temperature Cycle Damage Resistance Of Drainage Asphalt Mixtures, Liu Fuming, Wu Di, He Qingde, Yang Zhiping

Journal of China & Foreign Highway

In order to study the effect of fiber stabilizer on the water temperature cycle damage resistance of drainage asphalt mixture, drainage asphalt mixture without fiber stabilizer and with wood fiber, polyester fiber, and basalt fiber, respectively, were compared through tests. By standard dispersion test and immersed dispersion test, the anti-spalling ability of the mixture was analyzed. Under the same asphalt condition, the standard dispersion loss of the drainage asphalt mixture was reduced to different degrees after adding fiber stabilizer, which could increase the anti-spalling property of the drainage asphalt mixture to some extent. The splitting, indirect tensile, and rutting tests …

Study On Road Performance Of High Content Phosphogypsum Cement Stabilized Red Clay, Yang Dezhong, Chen Kaisheng, Li Qiang

Journal of China & Foreign Highway

In response to the waste of phosphogypsum resources and engineering characteristics of red clay, by referring to the mix ratio design method of fly ash mixtures, 18 sets of mix ratio samples were set up indoors. By conducting compaction tests, seven-day unconfined compression strength tests, water-stability tests, and CBR tests, exploratory research was conducted on the road performance of high content phosphogypsum stabilized red clay. The results indicate that the optimal water content of high content phosphogypsum stabilized red clay is lower than that of plain red clay. The seven-day unconfined compression strength is 1.8-3.7 times that of plain red …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Development Of Cost-Effective High-Modulus Asphalt Concrete (Hmac) Mixtures Using Crumb Rubber And Local Construction Materials In Louisiana., Ibrahim A.I.E Elnaml

LSU Master's Theses

One of the emerging solutions to enhance the durability of asphalt pavements is the use of a French asphalt mix known as “High-Modulus Asphalt Concrete (HMAC).” This mix uses a hard asphalt binder, high binder content (about 6%), and low air voids content as compared to Superpave mixtures. The key objective of this study was to develop a cost-effective HMAC mixture using crumb rubber and local materials in Louisiana. To achieve this objective, four HMAC mixtures were prepared using two asphalt binders (PG 82-22 and PG 76-22 plus 10% crumb rubber) and two Reclaimed Asphalt Pavement (RAP) contents (20% and …

Research And Applications Of Artificial Neural Network In Pavement Engineering: A State-Of-The-Art Review, Xu Yang, Jinchao Guan, Ling Ding, Zhanping You, Vincent C.S. Lee, Mohd Rosli Mohd Hasan, Xiaoyun Cheng

Michigan Tech Publications, Part 1

Given the great advancements in soft computing and data science, artificial neural network (ANN) has been explored and applied to handle complicated problems in the field of pavement engineering. This study conducted a state-of-the-art review for surveying the recent progress of ANN application at different stages of pavement engineering, including pavement design, construction, inspection and monitoring, and maintenance. This study focused on the papers published over the last three decades, especially the studies conducted since 2013. Through literature retrieval, a total of 683 papers in this field were identified, among which 143 papers were selected for an in-depth review. The …

Experimental Investigation Of The Performance Of A Hybrid Self-Healing System In Porous Asphalt Under Fatigue Loadings, Shi Xu, Liu Xueyan, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, which is designed to achieve autonomic damage repair in asphalt pavement, offers a great life-extension prospect and therefore not only reduces pavement maintenance costs but also saves energy and reduces CO2 emissions. The combined asphalt self-healing system, incorporating both encapsulated rejuvenator and induction heating, can heal cracks with melted binder and aged binder rejuvenation, and the synergistic effect of the two technologies shows significant advantages in healing efficiency over the single self-healing method. This study explores the fatigue life extension prospect of the combined healing system in porous asphalt. To this aim, porous asphalt (PA) test specimens with …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

The Role Of Rejuvenators In Embedded Damage Healing For Asphalt Pavement, Shi Xu, Xueyan Liu, Amir Tabakovic, P Lin, Y Zhang, S Nahar, B J. Lommerts, Erik Schlangen

Articles

Rejuvenator encapsulation technique showed great potential for extrinsic asphalt pavement damage healing. Once the capsules are embedded within asphalt pavement, the healing is activated on-demand via progressing microcrack. When the microcrack encounters the capsule, the fracture energy at the tip opens the capsule and releases the rejuvenator. Then the released rejuvenator wets the crack surfaces, diffuses into and softens the aged bitumen, allowing two broken edges to come in the contact, preventing further asphalt pavement deterioration. The quality and speed of the damage repair process strongly depend on the quality of rejuvenator, thus it is important to choose a proper …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

Laboratory Testing And Mechanistic Analysis Of Treated Subgrade Soils, Hari Kumar Reddy Yarrapureddi

Civil Engineering Theses

Calcium-based stabilizing agents such as cement and lime have been extensively used to improve the engineering properties of base and subgrade layers of pavement systems. Recently, polymers and chemical stabilizers have become popular due to cost efficiency, ease of application, and fast curing times. In this study, California Bearing Ratio (CBR) values of polymer and chemical treated soils were compared with the CBR values of soils treated with conventional stabilizers. Parametric sensitivity analyses was carried out on key parameters including the type of subgrade soil, stabilizing agent, stabilizing agent treatment levels, and moisture conditioning. Additionally, numerical analyses was performed to …

Bio-Binder—Innovative Asphalt Technology, Amir Tabakovic

Articles

The global road network spans 16.3 million km [1], of which 5 million km is in the EU. These road networks fulfil major economic and social goals by facilitating the movement of goods and people throughout the EU, and are therefore of the utmost importance to the economic and social life of the EU [2]. National governments invest heavily in their road networks, e.g., in 2014, EUR 53.33 billion was invested in the development and maintenance of the EU road network [3]. Each year, the world produces 1.6 trillion tonnes of asphalt [4], of which 218 million tonnes is produced …

An Investigation Into The Effects Of Fly Ash On Freeze-Thaw Durability Prediction, Yancy Schrader

Graduate Theses and Dissertations

Air is purposefully entrained into concrete primarily to improve resistance to freeze-thaw deterioration while saturated with water. Air entraining admixtures (AEAs) are chemical admixtures designed to entrain air into the concrete to provide adequate resistance to the effects of freezing and thawing. One of the challenges associated with air entrainment in concrete is the interaction of an AEA with supplementary cementitious materials present in the concrete, particularly fly ash. Fly ash is a by-product of the coal fired electrical generation industry, and often contains residual unburned carbon and other components that can increase the AEA demand of a particular concrete …

Effect Of Citric Acid On Slump, Compressive Strength, And Setting Time Of Belitic Calcium Sulfoaluminate Concrete, Israel Aguilar Rosero

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement has well established advantages related to fast setting time, fast strength gain, long-term strengths, shrinkage, and sustainability. Due to its fast setting and hardening, this type of cement has historically been used to repair concrete structures, highways, and runways. This work provides much needed guidance on establishing mix design criteria for BCSA cement. Guidance is also given on the effects of set retarders on strength, slump, and setting times. Citric acid and a phosphonic acid-based admixture were tested as retarders for different concrete mixtures. Three studies were performed. In the slump study five different water …

Application Of Percentage Within Limits Concepts On A Balanced Mix Design Of Asphalt Mixtures, Elvis Alexander Castillo Camarena

Graduate Theses and Dissertations

Many agencies have incorporated rutting, and more recently cracking, laboratory test requirements in the design process of asphalt mixtures. The objective of each additional specification is to produce a balance between the stability and durability of the final product. Although a performance-engineered mixture design (PEMD), denoted here as a balanced mix design (BMD), offers compelling benefits, there is concern regarding the compatibility of the BMD with current construction practices. The objective of this work is to correlate a BMD method with realistic binder content construction tolerances by applying the concepts of a percent-within-limits (PWL) approach to field QC/QA. First, Chapter …

Exploring The Variability In The Gray Scale Imaging Process Of Asphalt Samples, David Oluwawade Olatunji

Civil Engineering Undergraduate Honors Theses

Gray scale image analysis is a powerful tool for testing asphalt concrete materials. From material composition to surface properties, gray scale analysis has shown evidence as a non-invasive way to obtain information from asphalt samples. Casillas et al. used a gray scale analysis to measure the Representative Volume Element of three asphalt sample geometries to understand the minimum size at which an asphalt sample is representative of a larger homogeneous mixture [1]. While the gray scale analysis used in this experiment yielded results, there were unknown factors in the image capturing process. Particularly, not much was known about the effect …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …

Correction To: Recommendations Of Rilem Tc 260-Rsc For Using Superabsorbent Polymers (Sap) For Improving Freeze–Thaw Resistance Of Cement-Based Materials (Materials And Structures, (2019), 52, 4, (75), 10.1617/S11527-019-1375-4), Viktor Mechtcherine, Christof Schröfl, Michaela Reichardt, Agnieszka J. Klemm, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Agnieszka J. Klemm is affiliated to Glasgow Caledonian University, Glasgow, UK.

A Novel Self-Healing System: Towards A Sustainable Porous Asphalt, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, aimed to produce a sustainable asphalt pavement using green technology, has been studied in the past two decades. Technologies including encapsulated rejuvenator and induction heating have been proposed, demonstrated in the laboratory, and gradually evaluated in field application. This paper looks into the synergy effect of the above two technologies, where induction heating serves as the asphalt damage repair mechanism, requiring just 2 min heating time and encapsulated rejuvenator will replenish (rejuvenate) aged asphalt binder and reinstate bitumen’s healing ability. Moreover, the increased temperature from induction heating could in turn accelerate the diffusion process of rejuvenator into aged …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Data

Corresponding data set for Tran-SET Project No. 18PLSU13. Abstract of the final report is stated below for reference:

"Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Data

Corresponding data set for Tran-SET Project No. 18CTAM03. Abstract of the final report is stated below for reference:

"Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Data

Corresponding data set for Tran-SET Project No. 18STUTA01. Abstract of the final report is stated below for reference:

"This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Publications

Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized that by adding a thin layer of highly ductile ECC material between the existing pavement and overlay, reflective …

Investigation Of Physical And Dynamic Properties Of High Porous Concrete, Ildar Akhmadullin

Publications

This project pursued two main objectives: (1) providing opportunities to Baton Rouge Community College (BRCC) students to develop hands-on laboratory skills and exposure to the transportation field, and (2) investigating porous concrete properties. Several BRCC student groups performed the work presented within this report; students prepared samples with different porosity and permeability according to standard specifications. The testing of the samples was performed at the Louisiana Transportation Research Center (LTRC) facility under the supervision of LTRC specialists. Findings indicate that the porosity of samples is backward proportional to the compression strength. This function is not linear but can be estimated …