Transportation Engineering Commons^™

Road Zipper™, Purdue Ect Team

ECT Fact Sheets Archive

Construction work zones are growing in number around the world. The natural aging of existing roadway infrastructure ensures that more and more maintenance and rehabilitation will be required. Work zones, by their very definition, create two major problems that must be addressed in some way: safety and mobility. In the United States, highway work zones are responsible for almost 25% of all non-recurring congestion and 10% of overall congestion. Vehicle accidents are more common in work zones, and traffic congestion through work zones on urban arterials and freeways is often considered to be “unavoidable." To address these issues, ROAD ZIPPER™ …

Pavement Condition Index And Cost Of Ownership Analysis On Preventative Maintenance Projects In Kentucky, Dominic J. Michels

Theses and Dissertations--Civil Engineering

The Commonwealth of Kentucky has seen increasing use over time of preventative maintenance treatments on its asphalt pavements. Performance of two of the most prevalent treatments employed by the Kentucky Transportation Cabinet (KYTC) – Thin Asphalt Overlay (Thinlay) and Microsurfacing – had yet to be examined in-depth through condition surveys. This thesis describes the data collection process to find the Pavement Condition Index (PCI) of each preventative maintenance site in Kentucky from the last 10 years. With PCI from each site, deterioration curves were generated for each treatment – providing the estimated life extension benefit of each. The analysis then …

Development Of A Test Level 3 Transition Between Guardrail And Portable Concrete Barriers, Robert W. Bielenberg, David Gutierrez, Ronald K. Faller, John D. Reid, Phil Tenhulzen

Department of Civil and Environmental Engineering: Faculty Publications

Road construction often requires that work zones be created and shielded by portable concrete barriers (PCBs) to protect workers and equipment from errant vehicles as well as to prevent motorists from striking other roadside hazards. For an existing W-beam guardrail system installed adjacent to the roadway and near the work zone, guardrail sections are removed so a PCB system can be placed. A study was done to develop a crashworthy transition between W-beam guardrail and PCB systems. Design concepts were developed and refined through computer simulation with LS-DYNA. Additionally, a study of critical impact points was conducted to determine impact …

Bayesian Approach On Quantifying The Safety Effects Of Pedestrian Countdown Signals To Drivers, Angela E. Kitali

UNF Graduate Theses and Dissertations

Pedestrian countdown signals (PCSs) are viable traffic control devices that assist pedestrians in crossing intersections safely. Despite the fact that PCSs are meant for pedestrians, they also have an impact on drivers’ behavior at intersections. This study focuses on the evaluation of the safety effectiveness of PCSs to drivers in the cities of Jacksonville and Gainesville, Florida. The study employs two Bayesian approaches, before-and-after empirical Bayes (EB) and full Bayes (FB) with a comparison group, to quantify the safety impacts of PCSs to drivers. Specifically, crash modification factors (CMFs), which are estimated using the aforementioned two methods, were used to …

The Impact Of Project Delivery Methods On Dispute Occurrence In Public Highway Projects, Samaneh Nasrollahi, Ghada M. Gad, Alan Atalah

Master of Technology Management Plan II Graduate Projects

The construction industry is a complex and competitive industry in which different participants with different expertise, talents, and levels of knowledge work together to achieve their objectives and complete a project. Sine different participants with different interest involve in a construction project, therefore, conflicts arise and become inevitable. Conflicts in projects will cause an adversarial environment which result to disputes. Hence, if conflicts are not well managed and resolved in a timely manner, they quickly turn into disputes, which prevent the successful completion of the construction project, in terms of cost and time, and increasing the potential for poor project …

Lucidpipe™ Power System, Purdue Ect Team

ECT Fact Sheets Archive

In most gravity fed water transmission pipelines, it is desired to reduce excess pressure head to prevent undue strain on a pipeline and lower the incidence of leaks. Normally this is done with pressure reducing valves that essentially burn off this excess pressure as heat. The LucidPipe™ system converts it to low cost electricity thereby removing unwanted pressure and generating energy at the same time - energy that can be put used behind the grid or put back on the grid. The LucidPipe™ system extracts a small percentage of pressure head providing nearly invisible operation allowing water operators to fulfill …

Analysis Of Transit Accessibility For People With Disabilities, Rostam Khalid Mohammed Ameen Qatra

Masters Theses

The inconvenience of public transit systems and unavailability of bus stops in the United States has resulted in a heavy reliance on the private automobile. One of the main issues in transit services is accessibility, particularly for people with disabilities. This research is intended to compare estimated job accessibility measures by transit in Kalamazoo county for workers with reduced physical mobility and without. Using OpenTripPlanner (OTP) software, General Transit Feed Specification (GTFS), Open Street Map (OSM) and Longitudinal Employer-Housing Dynamics (LODES) data were analyzed to estimate job accessibility for people with mobility constraints. By using the shortest tree path method, …

Portable Modular Conveyor, Purdue Ect Team

ECT Fact Sheets Archive

The Portable Modular Conveyor-Material Placer (PMC) is a quick, easy, dependable and cost effective way to place materials in the limits of the confined grade or work area. This specialized piece of equipment was developed to place concrete in front of a concrete slip form-paving machine. The typical method of placing concrete requires a self-propelled belt placer, which is very expensive to purchase and mobilize to the jobsite. The PMC creates a significant cost savings in labor and equipment with the PMC. It is a direct replacement for conventional material placing equipment, including all in grade belt placing machines. As …

Comparison Of Safety And Operational Performances For Three Engineering Countermeasures, Ali Hamzah Hussein Alzuhairi

Masters Theses

While there have been many studies on engineering treatments for reducing traffic crashes or for improving intersection efficiency, few studies have been simultaneously taking both impacts into consideration. This thesis analyzed impacts of engineering countermeasures and determines when these countermeasures are cost effective with respect to the amount of traffic and the number of crashes. Both crash reduction and operational costs were compared for analysis. This study specifically investigated three countermeasures: changing from permitted to protected for a left-turn on minor approaches, leading pedestrian interval (LPI), and exclusive pedestrian phase (Barnes Dance). The general Safety Performance Functions (SPFs) from the …

Storm Damage - Murphy's Law, Dale Sedler, Mark Bailey

Purdue Road School

Examination of a disastrous event that required 4 coinciding occurrences happening that individually would likely have resulted in minor or no damage.

Storm Damage - Floating Culverts, Dale Sedler, Mark Bailey

Purdue Road School

A review of buoyancy issues culverts experience due to blockage. Includes discussion of blockage due to floating debris and issues with multiple culverts. Provides information on characteristics that help to determine if a culvert has "floated."

Storm Damage - Sr-57 June 2008, Dale Sedler, Mark Bailey

Purdue Road School

A review of the impact of the White River leaving its watershed and destroying a box culvert under SR-57 in Greene County, IN. Includes discussion about impact of illegal levee, and photos and discussion on contraction scour.

State-Of-The-Art Review Of Cathodic Protection For Reinforced Concrete Structures, Aimee Byrne, Niall Holmes, Brian Norton

Articles

Cathodic protection (CP) limits the corrosion of a metal surface by making it the cathode of an electrochemical cell. This can be achieved either by using a more active sacrificial anode to create a driving current, or by using inert anodes and impressing a current onto the cathode surface using an external direct current (DC) source. Impressed current cathodic protection (ICCP) is preferred where widespread protection is required, particularly in reinforced concrete structures. ICCP needs a constant DC power supply that is usually provided through a grid connection or independent generators. This paper presents the currently available CP systems for …

Bridge End Settlement Evaluation And Prediction, Jiwen Zhang

Theses and Dissertations--Civil Engineering

A bridge approach is usually built to provide a smooth and safe transition for vehicles from the roadway pavement to the bridge structure. However, differential settlement between the roadway pavement resting on embankment fill and the bridge abutment built on more rigid foundation often creates a bump in the roadway. Previous work examined this issue at a microscopic level and presented new methods for eliminating or minimizing the effects at specific locations.

This research studies the problem at a macroscopic level by determining methods to predict settlement severity to assist designers in developing remediation plans during project development to minimize …

Expedient Airfield Runway Repair Using Folded Fiberglass Mat, Christopher Y. Tuan, Willaim C. Dass

Department of Civil and Environmental Engineering: Faculty Publications

For expedient airfield runway repair, the US Air Force has developed a folded fiberglass mat to cover craters repaired with a well-compacted granular base material. The objective of this study was to evaluate the adequacy of using polymer plugs to anchor the mat to a repaired asphalt pavement for heavy aircraft operations. The effort consisted of materials testing, field experiments and analytical modeling. An 89,800-kg (198,000-pound) load cart having the footprint of a single C-5 main gear was pulled on a mat with wheels locked to simulate full braking forces. Anchor bushings were instrumented to measure anchor loads. A simplified …

Influence Of Warping On Stress For Restrained Concrete Slabs: For Application To Crcp, Corey M. Beck, W. Jason Weiss, Nathan T. Todd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Continuously-reinforced concrete pavement (CRCP) is widely used in transportation system because of its low maintenance requirement. However, the need for large volumes of steel creates a high cost for new construction. The Illinois Tollway is preparing to substantially renovate highways in and around Chicago and this work seeks to understand how concretes of varying mixture designs can be made thinner by reducing the amount of built-in stress. The experiment examines warping in beams subjected to various degrees of restraint, in an effort to assess effectiveness at reducing warping in continuously reinforced concrete pavements. Value added methodologies such as internal curing …

Developed Pipe Bursting Specifications Using High Density Poly Ethylene (Hdpe), Manoj Mohanraj

Master of Technology Management Plan II Graduate Projects

Pipe bursting is a trenchless method for replacing old deteriorated or under sized pipe by fracturing or splitting. Earlier published pipe bursting specifications do not completely cover the current state of the art and without proper allocation of risks. Specifications are set of written instructions given by the owner to the contractor. The developed Pipe Bursting specification with HDPE will help the owners, contractor, and engineers to carry out a successful burst timely and economically. In this research study, sixteen specifications from various sources were collected. Various agreements and disagreements among these specifications were identified, analyzed, and considered while developing …

A Microscopic Simulation Approach To Performance Evaluation Of Intelligent Transportation System Corridors: A Case In Michigan, Matthew Levi Clark

Masters Theses

A cost and benefit evaluation of the Michigan Department of Transportation’s (MDOT) Intelligent Transportation Systems (ITS) is performed through integration of analytical techniques and microscopic traffic microsimulation. Observed freeway corridor incident logs and characteristics are studied to determine representative incident management patterns on choice study corridors. The Quadstone Paramics microsimulation traffic package is used to model the selected corridors during various analysis scenarios and investigate the effects of ITS on freeway incident management performance.

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

College of Graduate Studies: Theses & Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

L&D Manual Turn Lane Storage Validation/Update, Deogratias Eustace, Sowjanya Ponnada

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Queuing occurs at intersections mostly due to overflow or inadequacy of turn bays. The ODOT L&D Manual Volume 1 has storage requirements for both signalized and unsignalized intersections. Figures 401-9E and 401-10E of the L&D Manual provide the required turn lane storage lengths which should be compared with the real world conditions to check for adequacy of these lengths as a measure of ensuring that accesses to the left turn lanes are not blocked. In addition to the projected turn lane volume, ODOT’s methodology incorporates both deceleration (based on the speed of the roadway) and potential blockage from the adjacent …

Identification Of Risk Factors Associated With Motorcycle-Related Fatalities In Ohio, Deogratias Eustace, Vamsi Krishna Indupuru, Peter W. Hovey

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Out of the 7,138,476 motorcycles operating on U.S. roads, 346,925 were registered in the state of Ohio in the year 2007. Although motorcycles represent only 2.8% of all registered vehicles in the state of Ohio, motorcycling accounts for more than 13% of Ohio highway traffic fatalities. Since 2005, Ohio has had a distressing distinction of being among the fifteen states that have sustained more than half of all motorcycle fatalities recorded in the USA (NHTSA 2007; NHTSA 2008a). For the past ten years, the overall motorcycle crash fatalities have been increasing while the motor vehicle occupant crash fatalities have been …

Optimal Loop Placement And Models For Length-Based Vehicle Classification And Stop-And-Go Traffic, Heng Wei, Qingyi Ai, Deogratias Eustace, Ping Yi

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Inductive loops are widely used nationwide for traffic monitoring as a data source for a variety of needs in generating traffic information for operation and planning analysis, validations of travel demand models, freight studies, pavement design, and even emission impact analysis of traffic operation. The loop data have also been used for vehicle length-based classification in many states including Ohio. The dual-loop detector consists of two single loop detectors which are placed apart at a fixed short distance, and this configuration enables the dual-loop detector data a potential real-time data source for speed and vehicle classifications. However, the existing dual-loop …

Development Of A Problem-Based Learning (Pbl) And Cooperative Learning (Cl) Transportation Engineering Course For Undergraduate Students, Deogratias Eustace

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

This study reports the findings of a project that was done during the implementation of a problem-based learning (PBL) and cooperative learning (CL) elements into an undergraduate transportation engineering course. The study procedure used the student course evaluations, including a survey questionnaire, and university-wide standardized student evaluations. Additionally, student homework, tests, and exam grades were used as part of the evaluation process. Two methods of teaching formats were evaluated: the traditional teaching method of lecturing and using end-of-chapter book questions for homework assignments and the new currently used teaching method of student field data collection, preparation of a lab report …

Evaluation Of The Role Of Driver’S Knowledge Of Who Has The Right-Of-Way Contributes To Interstate On-Ramp Crashes, Deogratias Eustace, Vamsi Krishna Indupuru

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

The knowledge of drivers on who has the right-of-way between the one on mainline lanes of a freeway and the one entering the freeway through on-ramp junction lane was evaluated. In addition, drivers’ opinions on how to make the on-ramp junctions safer were collected. A survey instrument with 21 items requesting drivers’ information in regard with demographics, freeway driving experience, knowledge of right-of-way and merging practices was used for data collection. The results show that crashes are relatively rare events and for some reasons, most of them never happen but result into near misses, which can not be reported and …

Rapid Runway Repair (Rrr): An Optimization For Minimum Operating Strip (Mos) Selection, David J. Duncan

Theses and Dissertations

Minimum Operating Strip (MOS) selection determines the exact placement of the MOS on the damaged runway, and therefore, the amount of munitions that need to be neutralized and the amount of damage that will need to be repaired. MOS selection, in essence, is the key determinant of the time required to attain an operational takeoff and recovery surface. Since the MOS selection stage determines the events and scope of work for all of the Rapid Runway Repair (RRR) stages that follow, it could be argued that this is the most important stage in the entire RRR process. The primary purpose …

Development Of Multiple Growth Strategies For Use In Developing Traffic Forecasts: A Robustness Approach, Deogratias Eustace, Eugene R. Russell, E. Dean Landman

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Decisions that may be based on misleading forecasts may lead to a misallocation of funds and to under-performing projects during construction and operation. Poor projections of demographic and socioeconomic data are usually cited as the major source of poor traffic assignment projections and hence, unfavorably conceived planning and construction of street and highway infrastructure facilities.

This report evaluated the accuracy of long range projections by using a transportation study done the in 1970s, projecting transportation demand 20 years into the future. The projected travel model inputs were compared with what actually happened after the horizon year had been reached and …

Performance Comparison Of A Roundabout Versus Two-Way Stop Controlled (Twsc) Intersections, Deogratias Eustace

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

The superior safety record of modern roundabouts is well known in Western Europe, Australia and in most British-influenced countries around the world. The experience from a single modern roundabout installed in the City of Manhattan, Kansas, some three years ago, also shares the same experience. A major study of the performance of Manhattan, Kansas, modern roundabout was conducted at Kansas State University (KSU) and was co-sponsored by Mac-Blackwell National Rural Transportation Study Center, Kansas State University, and the City of Manhattan. The study examined three intersections, one modern roundabout and two Two-Way Stop Controlled (TWSC) intersections with similar traffic conditions. …

The Engineer Speaks: Memoirs Covering Five Decades Of Highway Problems In Duval County, Arthur Neyle Sollee Sr

Arthur N. Sollee, Sr. Textual Materials

Published in 1982, this book details the history and problems creating the Jacksonville we know today. PALMM.

Sun, Sand And Water: A History Of The Jacksonville District U.S. Army Corps Of Engineers 1821-1975, George E. Buker

Books

A history of the Jacksonville district of the U. S. Army Corp of Engineers and their challenges to develop Jacksonville as a viable harbor and intracoastal waterways from 1821-1975

Bridge / Tunnel Crossing Study : Portland Harbor - Fore River, Portland - South Portland, Maine Department Of Transportation

Maine Collection

Bridge / Tunnel Crossing Study : Portland Harbor - Fore River, Portland - South Portland

Report by Fay, Spofford & Thorndike, Inc., Engineers, Boston, Mass.

Prepared for the Maine Department of Transportation, Augusta, Maine, 1973.

Contents: Table of Contents / List of Figures / List of Tables / Introduction / Summary of Findings / Section 1 - General Background - Location Study / Section 2 - Alternative Facilities and Locations / Section 3 - Comparison of Construction Costs - Tunnel Versus Bridge / Section 4 - Traffic Analysis / Section 5 - Cost Effectiveness Analysis / Section 6 - Financial …