Structural Engineering Commons^™

Design And Performance Of Fiber-Reinforced Concrete With Adapted Rheology For Construction And Repair Of Bridge Structures, Ahmed Abdelrazik

Doctoral Dissertations

“The objective of this document is to design high-performance fiber-reinforced self-consolidating concrete (FR-SCC) for infrastructure repair and fiber-reinforced super-workable concrete (FR-SWC) for bridge construction. The investigated fibers included propylene synthetic fibers, hooked steel fibers, double and triple hooked steel fibers, hybrid crimped steel fiber and polypropylene multifilament fibers, and micro-macro steel fibers. The fiber volume varied between 0 and 0.75%. An expansive agent (EA) was incorporated to compensate for shrinkage and induce compression in the concrete at early age. Two types of EA (G and K) were employed at 0 to 8%, by mass of binder. The investigated FRSCC and …

Incorporation Of Contaminated Sediment Into Environmentally Safe Concrete, Andrew Needs

Williams Honors College, Honors Research Projects

The research performed through this project provided some interesting results on how the different properties of the contaminated sediment can impact the strength of the new concrete.

Average three, seven, and fourteen-day strengths increased when comparing to the baseline mix developed for the experiment. Increases in strengths were notices in the ten and twenty-five percent soil replacement mixes. The largest increase was approximately thirty-three percent greater than the baseline average.

The results from the forty percent replacement test showed a significant decrease in strengths when comparing against the baseline mix. A loss of about thirty percent was observed between the …

Analysis Of Standardized Concrete Mixes, Riley Graybeal

Williams Honors College, Honors Research Projects

Concrete is one of the most common materials used in construction. It is mass produced throughout the country, with numerous different designs for concrete mixes. A common practice among concrete manufacturers is to use a standardized concrete mix design. These standardized mix designs are pre-tested and are not usually altered frequently. The hypothesis of this research project is that manufacturers do not constantly investigate new ways to save on their mixes, and simply use the same standardized mix designs.

In this research, investigations into what alterations may reduce the cost of standardized mixes began with a baseline mix design provided …

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …

State-Based Peridynamic Particle Method, Siavash Nikravesh Kazeroni

Civil Engineering ETDs

In this study, a novel discrete Peridynamics framework called the “State-Based Peridynamic Particle Model (SPPM)” is introduced. In this approach, a solid body is simulated by neither solving differential equations nor integral equations; instead, the simulation is accomplished by directly solving discrete systems of equations using finite summations. SPPM is formulated for a random distribution of particles, hence, it can be considered as a meshfree method. The assumptions of continuity and homogeneity are not necessary for this approach. The SPPM is a generalization of the “State-Based Peridynamic Lattice Model (SPLM)”. In the SPLM formulation, for sake of simplicity and computational …

Shrinkage Cracking In Concrete Tilt-Up Construction, Stewart Hooks, Jack Robinson

Architectural Engineering

The purpose of this project is to investigate a particular, undesirable cracking pattern in concrete tilt-up panels that, until now, did not have a known definite cause. The cause of this cracking pattern is hypothesized to be due to shrinkage restraint of the concrete panels. The cracking under investigation occurs at the bottom corners of the Tilt-Up panels, suggesting that the base of the panel is restrained from shrinkage. This project models various components of Tilt-Up Construction that have potential for restraining the panels from shrinking. This project consists of the following main components.

The first aspect of this project …

Evaluating The Bond Behavior Between Frp And Grooved Concrete Specimens Using Single Shear Pull Out Test, John Omboko

Master's Theses (2009 -)

Surface preparation affects the bond behavior between Fiber Reinforcing Polymer (FRP) composite material and concrete. In this research, a special type of surface preparation known as grooving, which involves cutting transverse grooves, is conducted on concrete blocks (specimens) that are categorized as either Unfilled (U) or Filled (F). This idea is to ascertain how the grooves affect the strength of FRP-bonded-concrete specimen. These two categories are then benchmarked to control (C) specimens which do not have grooves on them. Category U specimens only have the epoxy applied on the concrete surface while category F specimens have epoxy applied on both …

Ductile Corrosion-Free Gfrp-Stainless Steel Reinforced Concrete Elements, Maged A. Youssef, Mohamed E. Meshaly, Ahmed Elansary

Civil and Environmental Engineering Publications

Corrosion of steel rebars is known to cause deterioration of concrete structures that can lead to catastrophic failures. To mitigate this problem, steel rebars can be replaced with Glass Fiber-Reinforced Polymer (GFRP) rebars. However, the lack of ductility of GFRP-reinforced elements has prevented their use in many structural applications, especially in seismic areas. Stainless Steel (SS) rebars are corrosion resistant and have adequate energy absorption and ductility. However, they are much more expensive than steel rebars. This paper proposes the combined use of SS and GFRP rebars to achieve ductile and corrosion-free elements. The first challenge for such a proposal …

Identifying Damage, Predicting Expansion, And Determining The Effectiveness Of Sealers On Concrete Affected By Alkali-Silica Reaction And Freeze-Thaw, Matthew Caleb Waidner

Graduate Theses and Dissertations

Premature cracking of the barrier wall and pavement on I-49 south of Fayetteville, Arkansas due to a combination of Alkali-Silica Reaction (ASR) and freeze-thaw has led to ASR and freeze-thaw research at the University of Arkansas. Potential for further expansion (PFET), Damage Rating Index (DRI), and mitigation of freeze-thaw and ASR with sealers testing and results are contained herein. PFET results indicated that the pavement will not continue to expand from ASR. With other interstate pavements deteriorating prematurely throughout Arkansas, DRI has shown that most are damaged not only by ASR but by freeze-thaw too. Recommendations for freeze-thaw’s inclusion into …

Seismic Design Of A Prestressed Concrete Bridge, Alperen Ozel

LSU New Orleans Theses and Dissertations

Latest advancements in software have become an indispensable tool in structural analysis. The main goal of this thesis is to examine dynamic responses of bridges in seismic activity with the help of such tool as CSi Bridge. Therefore, throughout this study, a prestressed concrete bridge model will be thoroughly designed. In the first section, the required materials and structural components will be introduced. The following section will cover calculations required for modeling. The actual modeling of the structure will be carried out in Section 3. In Section 4, the set of required analysis for seismic design such as modal, pushover …

Effect Of Fly Ash Fortification In The Manufacture Process Of Making Concrete Towards Characteristics Of Concrete In Sulfuric Acid Solution, Asep Handaya Saputra, Muhammad Shohibi, Masatoshi Kubouchi

Makara Journal of Technology

Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH)2 within concrete. The reduced content of Ca(OH)2 through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete). In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics …

Phase I Evaluation Of Selected Concrete Material Models In Ls-Dyna, Bradley J. Winkelbauer

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Numerous roadside safety systems are configured with reinforced concrete materials, such as bridge railings, median barriers, and roadside parapets. These protective barrier systems are intended to safely contain and redirect errant vehicles as well as prevent impacts into hazardous fixed objects or other geometric features. The analysis and design of these structures may involve impact simulation with finite element software, like LS-DYNA, which includes multiple concrete material models. For such investigations, limited guidance is available for selecting preferred concrete material models and determining appropriate values for specific parameters. This Phase I study investigated the viability and performance of existing concrete …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

UBT International Conference

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the well-functioning of the entire structure. The use of a crystalline admixture during the …

Characterisation And Applications Of Iron Ore Tailings In Building And Construction Projects, Francis Atta Kuranchie

Theses: Doctorates and Masters

The mine tailings are generated as the wastes worldwide as a result of exploration, excavation, blasting, beneficiation and extraction of mineral ores. In Western Australia, due to the extensive mining activities and increasing low grade ores, there is generation of mine tailings in large quantities, which could lead to environmental and disposal problems. The common practice of handling the tailings are to store them in tailing dams or as stockpiles near mine sites. Limited quantities are sometimes used as backfills and other applications. The utilisation of tailings in building and construction projects, which may consume a large volume of wastes, …

Mechanical And Transport Properties Of Alkali-Activated Natural Pozzolans As Sustainable Binders, Brittany Radke

Calvert Undergraduate Research Awards

OPC production accounts for 5 to 7% of the global carbon dioxide (CO₂) emissions, contributing to global warming. The desire to reduce CO₂ emissions and produce more durable concrete has given impetus to search for new binders. It is suggested that alkali-activated natural pozzolans have the potential for use as a sustainable replacement for OPC in concrete.

The current study presented herein evaluated fresh, mechanical, and transport properties of alkali-activated natural pozzolan mortars containing various concentrations of sodium hydroxide solutions as an alkaline activator. To this aim, alkali-activated natural pozzolan mortars were made with concentrations of sodium …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

Reliability-Based Design Optimization Of Concrete Flexural Members Reinforced With Ductile Frp Bars, Bashar Behnam, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

In recent years, ductile hybrid FRP (DHFRP) bars have been developed for use as tensile reinforcement. However, initial material costs regain high, and it is difficult to simultaneously meet strength, stiffness, ductility, and reliability demands. In this study, a reliability-based design optimization (RBDO) is conducted to determine minimum cost DHFRP bar configurations while enforcing essential constraints. Applications for bridge decks and building beams are considered, with 2, 3, and 4-material bars. It was found that optimal bar configuration has little variation for the different applications, and that overall optimized bar cost decreased as the number of bar materials increased.

Precast/Prestressed Concrete Truss-Girder For Roof Applications, Peter S. Samir

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

Steel trusses are the most popular system for supporting long span roofs in commercial buildings, such as warehouses and aircraft hangars. There are several advantages of steel trusses, such as lightweight, ease of handling and erection, and geometric flexibility. However, they have some drawbacks, such as high material and maintenance cost, and low fire resistance. In this paper, a precast concrete truss is proposed as an alternative to steel trusses for spans up to 160 ft. without intermediate supports. The proposed design is easy to produce and has lower construction and maintenance costs than steel trusses. The proposed design is …

Bringing To Life The World’S Tallest Structure, Jonathan Weigand

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

Intended as the centerpiece of constructional developments in Dubai, the Burj Khalifa now stands as the tallest building ever constructed. The uniquely designed foundation consists of a concrete raft supported by a cast-in-place pile system protected by waterproofing membrane to inhibit corrosion. The structural design integrates high-performance reinforced concrete and steel and incorporates an engineered “Y” shape that limits the lateral wind pressure on the building. Engineers applied the latest advancements in high-rise technology to develop an optimized construction plan that consisted of segmented tasks that promoted the staff to work at a quick yet manageable pace. This article details …

Experimental And Numerical Investigations On Bond Durability Of Cfrp Strengthened Concrete Members Subjected To Environmental Exposure, Haider Al-Jelawy

Electronic Theses and Dissertations

Fiber reinforced polymer (FRP) composites have become an attractive alternative to conventional methods for external-strengthening of civil infrastructure, particularly as applied to flexural strengthening of reinforced concrete (RC) members. However, durability of the bond between FRP composite and concrete has shown degradation under some aggressive environments. Although numerous studies have been conducted on concrete members strengthened with FRP composites, most of those studies have focused on the degradation of FRP material itself, relatively few on bond behavior under repeated mechanical and environmental loading. This thesis investigates bond durability under accelerated environmental conditioning of two FRP systems commonly employed in civil …

Pullout Strength Of Epoxy Anchors Installed Underwater, Jeffrey Lee Blanchette

Master's Theses

This work presents the development of a test program and the results from the final round of testing to better understand the effect a submerged anchor installation has on the pullout strength of epoxy anchors. Two different epoxies were tested at embedment depths of two, four, and six bar diameters. These tests utilized three distinct installation procedures under dry and submerged conditions. The testing program occurred over five phases, with the final round used in analysis consisting of 24 anchor pullout tests. These tests showed that the presence of water did not have an effect on the epoxy bond when …

Effects Of Alternate Cementitious Materials On Compressive Strength And Environmental Impacts Of Cement Mix Designs., Mitchell R. Bush

Materials Engineering

Specific proportions of Portland cement, fly ash, and blast furnace slag cement mixtures where chosen by a ternary phase diagram to be investigated. By experimental testing and company data history fly ash was limited to not exceed 30% and contribution of Portland cement must be over 50%. Ten chosen mix designs were batched by following ASTM C305-94 and cured for twenty-eight and forty-two days, the extended cure length allows the reaction of pozzolanic material with calcium hydroxide to complete. Compressive strength testing at forty-two days yielded low strength for mix designs with 20% or less Portland cement compared to our …

Structural Performance Of Reinforced Concrete Flat Plat Buildings Subjected To Fire, Sara Jean George

UNLV Theses, Dissertations, Professional Papers, and Capstones

Reinforced concrete structures are typically considered to have inherent resistance to fire. However, several concrete structures around the world have experienced partial or total collapse under fire. Reinforced concrete flat-plate is a type of structural system widely used for office and residential buildings. Flat plate construction is prone to punching shear failure at slab-column connections which may lead to a catastrophic progressive collapse. The slabs of flat-plates generally have very thin concrete cover leaving steel reinforcement more sensitive to thermal loads. Little is known in the engineering community about the structural performance of flat-plate structures subjected to fire. Through a …

Accelerated Construction For Pedestrian Bridges: A Comparison Between High Strength Concrete (Hsc) And High-Strength Self Consolidating Concrete (Hs-Scc), John J. Myers, Kurt Bloch

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

High-strength concrete (HSC) and glass fiber reinforced polymer (GFRP) bars are materials utilized in bridge construction to lower cost, reduce construction time, and increase service life of bridge structures. Recently, high-strength self-consolidating concrete (HS-SCC), a highly flowable concrete that does not require vibration, has been developed as a viable alternative to HSC for use in situations with congested steel or a need for rapid construction. Coupling HS-SCC with GFRP bars could create durable structures built rapidly. Several performance related issues remain to be investigated such as the behavior of prestress loss, shear, creep, shrinkage, thermal gradients, mechanical property development, time …

Recycling Waste Latex Paint In Overlays, Rigid Pavements, And Pervious Concrete, Oscar Inez Quiroz

UNLV Theses, Dissertations, Professional Papers, and Capstones

With over 16 million gallons of latex paint (WLP) being disposed every year it is the largest by volume, liquid hazardous waste in the United States. WLP is difficult to recycle and hazardous to the environment due to the volatile organic compounds it contains. Several methods exist for disposing WLP including paint swaps, combustion, drying and discarding in a landfill, and by placing pigments in cement. Many communities are moving to dispose WLP by drying and placing in a landfill due to the reduced cost. However, this is the least preferred technique for the environment because it creates a need …

Piedras Blancas Light Station Vista Point Improvement Plan, Larissa Heeren, Reuben Juster, Annamarie Usher, John Rossi, Nick Mitchell

Mechanical Engineering

Piedras Blancas Light station Improvement Involved the design of two separate parking lot/vista point plans as well as the creation of a concrete Iron Ranger located near the gift shop on site.

Frp Confined Reinforced Concrete Circular Cross Section Seismic Applications, Jeffrey G. Lyon

Master's Theses

In recent earthquakes, structures have not performed as well as expected resulting in a need for better means of retrofitting and improvements in seismic design. Fiber Reinforced Polymers (FRP), as a material with potential to increase strength and ductility of columns in conjunction with capacity design methodology, has promise for seismic design. By investigating the displacement, ductility, and flexural strength properties of FRP confined reinforced concrete circular cross sections, this study analyzes the seismic applications of FRP confinement.

The study is performed by incorporating an FRP confined concrete stress-strain model into a developed Moment-Curvature and PM Interaction software. This software …

Nonlinear Model For Reinforced Concrete Under Cyclic Loading, Aly Said, M. Elmorsi, M. Nehdi

Civil and Environmental Engineering and Construction Faculty Research

Most of the available shear models for reinforced concrete rely on empirical formulations. In this study, a rational shear stress function is used to define the shear stress–strain envelope for reinforced concrete. Cyclic rules are proposed to define the loading, unloading and reloading relationships for reinforced concrete under shear stress reversals. A normal stress function describing the cyclic relationship of concrete under axial stress is also introduced. The proposed functions are verified using experimental data of reinforced concrete panels tested under monotonic and cyclic loading. Subsequently, the normal and shear stress functions along with their cyclic rules are integrated in …