Structural Engineering Commons^™

Joining Methods For Continuous Fiber Reinforced Thermoplastic Composites In Structural Applications, Andrew Moran

Electronic Theses and Dissertations

Continuous fiber reinforced thermoplastic (CFRTP) composites have been proposed as an alternative to metals in structural applications. CFRTP composites can be used to create structures that are lighter weight, have better resistance to environmental factors, and have the potential to be recycled. However, one of the main challenges to CFRTP composites is connections between structural members. The goal of this thesis is to investigate the feasibility of joining CFRTP composites to both similar and dissimilar materials through literature review, coupon testing, design of a structural joint, and a small scale laboratory prototype of the joint. To achieve this goal the …

Integration Of Material Characterization, Thermoforming Simulation, And As-Formed Structural Analysis For Thermoplastic Composites, Philip M. Bean, Roberto A. Lopez-Anido, Senthil Vel

Civil Engineering Faculty Scholarship

An improved simulation-based thermoforming design process based on the integration of material characterization and as-formed structural analysis is proposed. The tendency of thermoplastic composites to wrinkle during forming has made simulation critical to optimized manufacturing, but the material models required are complex and time consuming to create. A suite of experimental methods has been developed for measurement of several required properties of the molten thermoplastic composite. These methods have the potential to enhance thermoplastic composites manufacturing by simplifying and expediting the process. These material properties have been verified by application to thermomechanical forming predictions using commercial simulation software. The forming …

Evaluating The Effects Of Shored Construction On Steel Girder Composite Bridges, Parker Brooks

Doctoral Dissertations and Master's Theses

Steel composite girder bridges provide economic advantages and higher load-carrying capacity than non-composite alternatives. Over the years, a conventional sequence of un-shored construction for steel girder composite bridges has been developed. There is an alternative construction sequence, known as shored construction, that uses temporary supports (discretely or fully supported) for the superstructure during the installation of metal forms and the pouring of concrete. Shored construction also can be used in an Accelerated Bridge Construction (ABC) practice where construction occurs at a nearby site and fully-formed elements are transported to the final site using self-propelled modular transporters (SPMTs). In order to …

Analysis Of Laminated Beams: A Bibliometric Review, Arati Waghmare, Sanjay Kulkarni

Library Philosophy and Practice (e-journal)

In this paper statistical analysis of literature on “Analysis of Laminated Beams” using Scopus and Web of Science database is done. Reason behind bibliometric study of literature is to understand the extent of research in this particular area. Since Scopus and Web of Science indexing are known as the most reliable sources amongst all the peer reviewed journals, literature from Scopus and Web of Science database only is taken into consideration. Benchmarks used for the analysis are publications in a year, published articles of different authors, citations of authors etc. Considered period is from 2000 to 2020. It is found …

Seismic Design Coefficients For Speedcore Or Composite Plate Shear Walls - Concrete Filled (C-Psw/Cf), Shubham Agrawal, Morgan Broberg, Amit H. Varma

Bowen Laboratory Research Reports

This report summarizes the results from FEMA P695 analytical studies conducted to verify the seismic design factors for composite plate shear walls – concrete filled (C-PSW/CF), also referred to as Speedcore. ASCE 7-16 provides the seismic design factors, which include the seismic response modification factor, R, deflection amplification factor, C_d, and overstrength factor, Ω_o, for various approved seismic systems. C-PSW/CFs are assigned a response modification factor of 6.5, a deflection amplification factor of 5.5, and an overstrength factor of 2.5 for C-PSW/CFs. These seismic design factors were selected based on the seismic performance of similar structural …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Novel Structural Health Monitoring And Damage Detection Approaches For Composite And Metallic Structures, Shervin Tashakori

FIU Electronic Theses and Dissertations

Mechanical durability of the structures should be continuously monitored during their operation. Structural health monitoring (SHM) techniques are typically used for gathering the information which can be used for evaluating the current condition of a structure regarding the existence, location, and severity of the damage. Damage can occur in a structure after long-term operating under service loads or due to incidents. By detection of these defects at the early stages of their growth and nucleation, it would be possible to not only improve the safety of the structure but also reduce the operating costs. The main goal of this dissertation …

Buckling Analysis Of Laminated Composite Box Beams, Domagoj Lanc, Goran Turkalj, Josip Brnic

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Behaviour Of Reinforced Concrete And Composite Conical Tanks Under Hydrostatic And Seismic Loadings, Ahmed Elansary

Electronic Thesis and Dissertation Repository

Conical liquid storage tanks are widely used to store different liquids and to provide water supply at cities and municipalities. However, no comprehensive guidelines currently exist in the codes of practice for the structural analysis and design of such tanks. The walls of a conical tank can be made of steel, reinforced concrete, or a combination of the two materials in a composite type of construction in which steel and concrete walls are connected using steel studs. The research conducted in this thesis provides a comprehensive understanding of the structural behaviour of reinforced concrete and composite conical tanks under hydrostatic …

Application Of Polyurethane Products In Accelerated Construction Of Innovative Noise Barrier, Bahman Daee

Electronic Thesis and Dissertation Repository

Noise barriers (sound walls) are usually constructed along roadways to mitigate the airborne noise emanating from vehicles. They are currently built using various materials including precast concrete panels, masonry, wood and transparent sheets. The main challenge in roadside construction is the obstruction of roadways during the construction, which may result in traffic congestion, public dissatisfaction, car collision and subsequently fatalities. In order to decrease the risk of roadside construction, accelerated and non-obstructive methods are highly preferred by transportation authorities.

An innovative wall system comprised of polyurethane products is proposed, developed and investigated for application in accelerated construction of noise barriers. …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

Interfacial Strength Between Prestressed Hollow Core Slabs And Cast-In-Place Concrete Toppings, Ryan M. Mones

Masters Theses 1911 - February 2014

The horizontal shear strength of the interface between prestressed concrete hollow core slabs and cast-in-place concrete topping slabs was evaluated through a set of 24 push-off experiments. The push-off test specimens featured segments of dry-mix and wet-mix hollow core slabs with a variety of surface treatments including machine finished, sandblasted, broom roughened, rake roughened and grouted. A cast-in-place slab was poured on top of the hollow core specimens to form a 15 inch by 15 inch interface between the two materials. Results indicate the average horizontal shear strength of the push-off specimens was 227 psi. Higher shear strength and slip …