Structural Engineering Commons^™

Advancing Solar Farm Resilience: Cfd-Driven Wind Load Optimization, Aly Mousaad Aly

Faculty Publications

This study investigates wind load design methods for ground-mounted solar panels and arrays by comparing Computational Fluid Dynamics (CFD) simulations with design standards. A case study of a solar farm impacted by Hurricane Maria examines the effects of elevation height, tilt angle, and variations in the American Society of Civil Engineers (ASCE) standards on wind loads and structural failure. Turbulence models, including Reynolds Stress Model, k–ε Model, and Large Eddy Simulation (LES), are used to analyze wind pressures, lift, drag, and peak pressures. Results show Phase 1 experienced higher wind loads than Phase 2 due to design differences. A cost-benefit …

Fast Penetration Test As An In-Situ Method For Assessing Buildability In 3d Concrete Printing, Ali Fasihi, Nicolas Ali Libre

Miners Solving for Tomorrow Research Conference

No abstract provided.

Digital Fabrication With Fiber-Reinforced Concrete, Haodao Li, Kamal H. Khayat

Miners Solving for Tomorrow Research Conference

No abstract provided.

Quality Assurance Framework For Recovered Binders And Aggregates From Asphalt Mixtures Incorporating Recycled Materials, Eslam Deef-Allah, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study proposes that a proactive quality assurance (QA) framework for asphalt mixes with recycled materials, i.e., reclaimed asphalt pavement and recycled asphalt shingles, should be developed. Quality control (QC) is generally concerned with the contractor's obligation to produce mixes which meet the job mix formula (JMF) targets. However, QA considers the variability in fabrication processes and materials and offers monitoring by evaluating the contractor's performance. Although both aggregate gradations and asphalt contents were within the JMF specifications, the recovered binders revealed significant differences from the contract binders in the JMF. Rheological tests indicated increased stiffness and elasticity but reduced …

Underlying Mechanisms Of The Effect Of Microfines Of Manufactured Sand On Non-Linear Structural Build-Up Of Cement Paste, Jiang Zhu, Jiaping Liu, Kamal H. Khayat, Xin Cheng, Wei Zhao, Zhen Li, Xin Shu, Yongbo Huang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The rheological properties of cement-based materials made with manufactured sand vary with the content and physio-chemical properties of microfines in the sand. However, the evaluation of rheological properties regarding the structural build-up at early-age hydration remains challenging for the cementitious materials prepared with different manufactured sands, due to complicated underlying structuration mechanisms. This paper studies the effect of disparate microfines of different manufactured sands on the non-linear growth of static yield stress of cement pastes at rest. The paste mixtures were prepared with 0.40 and 0.275 water-to-cement mass ratio (W/C) and had a fixed mini-slump flow of 240 ± 5 …

Experimental Investigation Of Multi-Cell Column Foun-Dations Under Bending Loads, Mostafa Abdo Abdllah Sharp

Journal of Engineering Research

This study investigates the structural behavior of connections between multi-cell columns and foundations under bending loads. The term "multi-cell" refers to sections with multiple longitudinal hollow cores separated by thin webs. A total of eight specimens were modeled and analyzed using the finite element software ABAQUS/CAE [1], under a single loading line system until failure. To facilitate this study, a control specimen was created as a benchmark, enabling the assessment of various parameters' impact on the connection. These parameters include embedment depth, the number of cells in the column, the presence of shear studs, internal plates, and concrete infill within …

The Performance Of Different Systems In Resisting Seismic Loading For High Rise Concrete Structures, Samy A. Fawzy

Journal of Engineering Research

High-rise buildings are subjected to gravity and mostly lateral loading from seismic and wind loads that affect the behavior of such structures. In this study, we will deal with the seismic behavior of different concrete systems. Moment resisting frame, Shear wall, global bracing and dual system are used in this study. A 3D model in static and dynamic analysis was done using ETABS software then a pushover analysis and a parametric study as well for different systems. The study proved that the case of moment resisting frame is the worst in resisting displacements and drift as well. Although the model …

Numerical Analysis Of Cold-Formed Built-Up Battened Steel Columns Under Eccentric Compressive Loading, Mai Mohamed Sheta, Hanan Hussein Eltobgy, Mohamed Massoud El Saadawy, Khaled Abdallah Gharib

Journal of Engineering Research

This paper presents a 3D finite element model simulation using ABAQUS finite element software to investigate the behavior of steel battened beam columns under uniaxial loads. The columns consist of double-channel cold-formed slender open sections. The study highlighted the effects of various factors on the ultimate capacity of these beam-column members.

By considering both global and local imperfections, the model focuses on the structural strength and performance of battened cold-formed steel columns made from built-up sections. These cold-formed steel (CFS) columns have a slenderness ratio ranging from 50 to 162. Axial loads are applied at the pin-ended support of the …

Non-Linear Analysis Of Axially Loaded Built-Up Open Section Cold-Formed Columns, Mai Mohamed Sheta, Hanan Hussein Eltobgy, Mohamed Massoud El Saadawy, Khaled Abdallah Gharib

Journal of Engineering Research

Built-up open cold-formed sections are commonly used in entrances, structural corners, and window frames. These elements exhibit low torsional stiffness and are highly susceptible to cross-sectional deformation. Battened built-up cold-formed steel (CFS) open columns offer enhanced load-carrying capacity when individual profiles cannot withstand applied loads.

Extensive research has focused on understanding the buckling behavior of these structural elements. However, limited studies have explored the impact of spacing between cold-formed C-channel sections. Existing research suggests that battened columns with adequately spaced members exhibit superior structural performance compared to those with closely spaced channels.

A critical factor affecting the performance of battened …

Numerical Study For Strengthening Hexagonal Castellated Steel Beams Using Hexagonal Ring Stiffeners, Amany M. Morad, Omnia F. Kharoub, Nashwa Yossef

Journal of Engineering Research

This paper investigates numerically how the castellated steel beams are affected by the addition of hexagonal stiffeners around hexagonal web openings. Increasing the CSBs' load-bearing capacity and improving their overall structural behavior are the main objectives of this strengthening technique. Although there are different failure modes as a result of castellation, the main emphasis of this study is web post-buckling. Using ABAQUS software, a 3D finite element model is created to analyze the beam's behavior. The model's accuracy was validated by comparing its results with those from previous experimental studies. Failure loads, failure modes, and load-deflection curves of CSBs are …

Bell Ford Bridge Reconstruction Project, Daniel Kurdziel, Jim Barker, Matt Lee

Purdue Road School

The Bell Ford Bridge was originally constructed in 1869 until it collapsed in the 20th century. The remains were salvaged and stored for 20 years until it was to be rebuilt in Hamilton County, IN. This is the only remaining Combination Post Truss in existence and was rebuilt using 95% of the original iron and 10% of the original timber.

Design Of An Electro-Hydraulic Laboratory Test System For Adjusting The Inclination Angle Of Sowing Machines, Aytac Moralar, Figan Dalmis, Bahattin Akdemir

The Philippine Agricultural Scientist

Field testing of grain sowing machinery requires favorable field conditions and sufficient time periods, making laboratory tests a preferred alternative for determining performance under controlled conditions. However, a standardized testing system for evaluating sowing machinery has not yet been established. In this study, a test system was designed for laboratory testing of universal grain sowing machines. A movable platform was built on a chassis made using sheet metal with different dimensions and profiles. It operates through a hydraulic system via a programmable logic controller-based control system. The sowing machine placed on this platform allows for inclination adjustments (front, back, right, …

Proof Of Concept: Using Uas Technology To Accomplish Aerial Roof Inspections, Madison R. Fanning

Theses and Dissertations

With the growing use of simulation across industries, the digital twin remains an underexplored research area, particularly in emergency management and response. Its real-time updating capability is often overlooked due to the misconception that "digital twin" is merely a complex term for simulation. This paper highlights its distinctiveness through an evasion exercise involving two independent entities in a collocated environment. Using a highly integrated virtual environment (HIVE) and internet of things (IoT) devices, we link the physical system with an analytical simulation, demonstrating the impact of lag times in high-pressure scenarios. The computational model leverages agent-based modeling (ABM) and discrete-event …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

Impact Of Aggregate Characteristics On Frictional Performance Of Asphalt-Based High Friction Surface Treatments, Alireza Roshan, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

High Friction Surface Treatments (HFST) are recognized for their effectiveness in enhancing skid resistance and reducing road accidents. While Epoxy-based HFSTs are widely applied, they present limitations such as compatibility issues with existing pavements, high installation and removal costs, and durability concerns tied to substrate quality. As an alternative to traditional Epoxy-based HFSTs, this study investigated the effects of aggregate gradation as designated by agencies on the performance of asphalt-based HFST. Various aggregate types were assessed to evaluate friction performance and the impact of polishing cycles on non-Epoxy HFST. It was found that adjustments in aggregate size and gradation may …

Correlating The Compositional Changes To The Rheological Properties Of Recovered Asphalt Binders From Recycled Asphalt Mixtures: Insights From The Thermogravimetric Measurements, Eslam Deef-Allah, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Assessing the binder performance of thermal characterization is critical for quality control. This is pertinent for recovered binders from mixtures, which may not be in adequate quantities to evaluate their performance, particularly in mixtures containing reclaimed asphalt pavement (RAP). The present study deployed a thermogravimetric analyzer to evaluate compositional changes in recovered binders from RAP-containing mixtures, focusing on thermograph and derivative of thermograph (DTG) characteristics and correlating the results to rheological features. Incorporating RAP in mixtures influenced recovered binders' DTG shapes, reducing low-combusted components (%LCC) and increasing residues (%R). The recovered binder from the zero-RAP-containing mixture showed a 4.36% increase …

Flexural Strengthening Of Reinforced Concrete Beams Using Nsm Gfrp: Assessing Key Parameters, Berlant Arab

Theses and Dissertations

The structural integrity and longevity of Reinforced Concrete (RC) beams are critical to modern construction, influencing safety, usability, and maintenance costs over time. As civil engineering endeavors to meet the challenges posed by aging infrastructure and evolving usage demands, rehabilitating and strengthening RC structures have become essential practices globally. This research focuses on a prevalent yet innovative method of enhancing RC beams: the application of Near Surface Mounted (NSM) Glass Fiber Reinforced Polymer (GFRP) bars.

GFRP is increasingly favored in structural engineering due to its superior properties to traditional materials. These include high tensile strength, resistance to corrosion, lightweight nature, …

Effect Of Shrinkage-Mitigating Materials, Fiber Type, And Repair Thickness On Flexural Behavior Of Beams Repaired With Fiber-Reinforced Self-Consolidating Concrete, Jingjie Wei, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

While self-consolidating concrete (SCC) has emerged as a highly effective approach for the repair of concrete structures, there have been few investigations regarding the effect of the combination of different fiber and shrinkage-mitigating material types (shrinkage-reducing admixture, SRA; superabsorbent polymer, SAP; and expansive agent, EA) on the flexural behavior of repaired structures. This study aims to explore the influence of three different shrinkage-mitigating materials (1.25%–2.5 % SRA, 4%–8% EA, and 0.2%–0.4 % SAP), four fiber types (two macro synthetic fibers, MSFA and MSFB; 5D hooked steel fibers, 5D; a combination of 80 % 3D hooked steel +20 % short steel …

Simulation-Based Models For Postearthquake Response: A Survey And Research Directions, Abhijit Gosavi, Lauryn A. Spearing, Lesley H. Sneed

Engineering Management and Systems Engineering Faculty Research & Creative Works

Computer simulation is increasingly being used by emergency planners as a tool to improve disaster response given that it can model real-world scenarios, such as earthquakes. Although there has been an increase in simulation research focused on disaster response, much of this literature is from disparate fields and across disaster scenarios. To bridge this gap, this paper surveys simulation-based models for post-earthquake response from the year 2000 onward. Advantages of simulation over closed-form statistical models are discussed. Three main subproblems in post-earthquake response models are explored: (1) service distribution (e.g., food, water), (2) infrastructure restoration (at the building and transportation …

Optimization Of The Cross-Section Of Generic Flexible Bridges, Manal Kamal Zaki, Mina M. Helmy, Mark M. Tawadros

Journal of Engineering Research

This paper investigates the behavior of flexible bridges prone to aerodynamic instabilities due to wind. Optimal cross-sections that reduce aerodynamic forces are recommended. This is achieved by studying a variety of bridge sections with different widths of upper and lower sloping edges in addition to studying the upper and lower cramps of the deck. The wind velocities are also parameterized. Computations are developed based on the powerful computational fluid dynamics (CFD) method known as FLUENT and embedded in ANSYS software. For parametric study, a design of experiments (DOE) is performed based on the response surface methodology (RSM) combined with the …

Preliminary Spectral Matching Analysis Of The Rod El-Farag Region In Cairo, Egypt, Ahmed F. Youssef, Amr Z. Elkady, Ayman A. Seleemah

Journal of Engineering Research

Abstract: Earthquake engineering assessments are essential for evaluating the seismic response of structures. Nonlinear dynamic analysis is a highly effective method for evaluating seismic re-sponse, considering the complex, three-dimensional, and dynamic behaviour of structures during earthquakes. The complexity of seismic damage assessment arises from ground motion and struc-tural modelling parameters. Spectral matching is a key method in seismic codes and aids in selecting earthquake accelerograms for performance- and force-based designs. Spectrum-matched data is increasingly used to estimate nonlinear structural responses. Spec-tral matching utilizes the wavelet adjustments introduced by Abra-hamson (1992) and refined by Hancock et al. (2006) to adjust earth-quake …

Optimizing And Validation Of Sustainable Uhpc With Waste Glass Powder Utilizing Modified Particle Packing Approach And Response Surface Methodology, Mohamed Taman, Elsaid Maaty, Alaa Mehrez, Ahmed Kamal Isaac

Journal of Engineering Research

The current study explores the potential of utilizing Waste glass powder (WGP) as an alternative to cement in the development of sustainable eco-friendly Ultra-high-performance concrete (UHPC). UHPC mixtures underwent optimization through the application of a Modified Andreasen and Andersen (MAA) particle packing model, resulting in a reduction of cement content from 900 to 800 kg/m³. Six mixes were cast, with varying levels of cement replacement ratios with WGP up to 50%. The evaluation focuses on the flowability, dry density, and mechanical properties of UHPC at different ages using normal curing. A statistical model utilizing response surface methodology (RSM) …

Improved Minimum Variance Channel Estimation Techniques For Ofdm Systems, Kwame S. Ibwe

Tanzania Journal of Engineering and Technology (TJET)

Orthogonal frequency division multiplexing (OFDM) systems face challenges in channel estimation due to noise, variability, and the doubly dispersive nature of wireless channels, which degrade performance. To address these challenges, a multichannel minimum variance double dispersive channel estimator is proposed. The method employs a hybrid approach that combines subspace and minimum variance techniques, optimizing the filter bank output power under a signal-to-noise ratio (SNR) constraint. This design preserves the desired signal while effectively suppressing disturbances, achieving robust performance with reduced computational complexity compared to existing methods. Simulation results demonstrate that the proposed estimator outperforms subspace and asymptotic methods in terms …

Design And Implementation Of Secured Hybrid Gateway Node For Securing Iot - Enabled Distribution Automation, Ally Bitebo

Tanzania Journal of Engineering and Technology (TJET)

The integration of smart grid and Internet of Things (IoT) technologies plays a crucial role in enhancing the quality of services provided by traditional electrical grids. This combination has enabled the introduction of new services, such as demand response, automatic meter reading, and IoT-enabled Distribution Automation (IoT-DA), which incorporates sensors, actuators, intelligent electrical devices (IEDs), and information and communication technologies to monitor and control the grid. However, this integration also introduces network security risks, including Denial of Service (DoS) attacks, false data injection, and masquerading attacks, such as system node impersonation that can transmit incorrect readings, trigger false alarms, and …

Review On State Of Art Of Smoothed Particle Hydrodynamics Method And Its Advances In Solid Dynamics, Harold J. Mtyana

Tanzania Journal of Engineering and Technology (TJET)

The world is witnessing continued collapse of both buildings and other structures during earthquakes, which is an example of a dynamic effect. One cause of such disasters may be inadequacies of techniques for modeling of these structures during analysis and design as compared to their actual responses during dynamic events. Also, techniques for numerical modeling and analysis of structures in place are meshed methods which do not accurately capture the actual behavior of structural elements especially under high dynamic actions due to the assumption that mesh geometry is unchanged geometry tend to change with respect to time step of such …

Effects Of Technical Debt On Software Interoperability, Leonard Peter Binamungu

Tanzania Journal of Engineering and Technology (TJET)

Technical debt (TD) refers to sub-optimal development decisions that make the software costly to maintain and evolve. Examples of TD include structural complexity, violation of coding styles, and code complexity. Existing research has investigated the nature, causes and indicators of TD, as well as tools and strategies for managing TD. However, although TD could hinder the ability of a software system to be interoperable with others, existing literature has limited evidence on how TD affects systems interoperability. This limits the ability of software engineering teams to manage TD in ways that do not hinder systems interoperability. To fill this void, …

The Development Of Sustainable Synthetic Fiber Reinforced Concrete Mix Design With Low Maintenance Cost, Kentesha L. High

Civil Engineering Dissertations - Archive

This dissertation presents the mix design of polypropylene SYN-FRC as an alternative to traditional concrete mixtures in construction roadways. The primary scope of work was to develop and implement a pavement system at The University of Texas at Arlington, specifically designed for the Dallas area, to minimize long-term maintenance. Additionally, the project aimed for expeditious construction to avoid traffic closure during new construction and maintenance. It also involved evaluating the pavement performance, providing the City of Dallas with specifications for the mix design of SYN-FRC. The sustainability of the synthetic fiber mix design for concrete roadways, compared to traditional concrete, …

Assessment Of Long Term Durability Of Prefabricated Frp Strip Systems For The Rehabilitation Of Concrete, Karunya Kanagavel

Civil Engineering Theses - Archive

Fiber Reinforced Polymer (FRP) composites provide an extremely effective means of rehabilitating deteriorating and understrength concrete elements due to their characteristics of high specific strength and stiffness, corrosion resistance, and potential long-term durability, lightweight nature, and ease of placement in the field. Despite significant use of these materials, there is still a lack of long-term durability data. With this in mind, the current study investigates the impact of environmental exposure and aging on 3 commercially available prefabricated carbon fiber reinforced composite strips and their recommended adhesives used in externally bonded rehabilitation with the aim of providing a comprehensive set of …

Floating Offshore Structures: A Literature Review Of Current Technologies, Dynamic Behavior, And Energy Applications Post-2021, Stephen Michael Nolin

Honors Theses and Capstones

No abstract provided.

Developing Inexpensive Sensors That Can Detect Roof Collapse From Snow Loads, Edward Sandy

Dissertations, Master's Theses and Master's Reports

In cold regions in the United States, residential timber structures are susceptible to roof collapses due to heavy snow accumulation. The recent updates in ASCE 7-22 have introduced reliability-targeted ground snow loads, leading to significant increases in design snow loads for certain areas. Despite this development, existing buildings in these regions designed under historical code requirements may be under-designed for snow load. This fact provides motivation to owners of these structures to pursue effective monitoring and mitigation strategies to prevent structural failures. This research focuses on the development of an early warning system utilizing cost-effective slope monitoring sensors to estimate …